A new type of power supply which was called oxy-fuel combustion power plant was introduced to reduce greenhouse gasses emission. In this paper the volatile emission characteristic of pulverized coal is studied under a...A new type of power supply which was called oxy-fuel combustion power plant was introduced to reduce greenhouse gasses emission. In this paper the volatile emission characteristic of pulverized coal is studied under air atmosphere and oxy-fuel atmosphere. Combustion experiments of Datong bituminous coal were carried out in a wire mesh reactor at heating rates of 1 K/s, 10 K/s and 1000 K/s respectively under air and O2/CO2 atmosphere conditions in order to investigate the volatile emission characteristic. The concentrations of volatile (mainly CO and CH4) emission were on-line measured by infrared gas analyzer. It was indicated that the concentrations of CO and CH4 in O2/CO2 atmosphere were higher than those in air. The direct oxidation of carbon and gasification reaction between carbon and CO2 are the main causes of the increased amount of CO. The higher concentration of CO2 also results in the increased amount of CH4 in O2/CO2 conditions.展开更多
Reducing a Pt loading with improved power output and durability is essential to promote the large-scale application of proton exchange membrane fuel cells(PEMFCs).To achieve this goal,constructing optimized structure ...Reducing a Pt loading with improved power output and durability is essential to promote the large-scale application of proton exchange membrane fuel cells(PEMFCs).To achieve this goal,constructing optimized structure of catalyst layers with efficient mass transportation channels plays a vital role.Herein,PEMFCs with order-structured cathodic electrodes were fabricated by depositing Pt nanoparticles by Ebeam onto vertically aligned carbon nanotubes(VACNTs)growth on Al foil via plasma-enhanced chemical vapor deposition.Results demonstrate that the proportion of hydrophilic Pt-deposited region along VACNTs and residual hydrophobic region of VANCTs without Pt strongly influences the cell performance,in particular at high current densities.When Pt nanoparticles deposit on the top depth of around 600 nm on VACNTs with a length of 4.6μm,the cell shows the highest performance,compared with others with various lengths of VACNTs.It delivers a maximum power output of 1.61 W cm^(-2)(H_(2)/O_(2),150 k Pa)and 0.79 W cm^(-2)(H_(2)/Air,150 k Pa)at Pt loading of 50μg cm^(-2),exceeding most of previously reported PEMFCs with Pt loading of<100μg cm^(-2).Even though the Pt loading is down to 30μg cm^(-2)(1.36 W cm^(-2)),the performance is also better than 100μg cm^(-2)(1.24 W cm^(-2))of commercial Pt/C,and presents better stability.This excellent performance is critical attributed to the ordered hydrophobic region providing sufficient mass passages to facilitate the fast water drainage at high current densities.This work gives a new understanding for oxygen reduction reaction occurred in VACNTs-based ordered electrodes,demonstrating the most possibility to achieve a substantial reduction in Pt loading<100μg cm^(-2) without sacrificing in performance.展开更多
Reducing the loading of noble Pt-based catalyst is vital for the commercialization of proton exchange membrane fuel cell(PEMFC),However,severe mass transfer polarization loss resulting in fuel cell performance decline...Reducing the loading of noble Pt-based catalyst is vital for the commercialization of proton exchange membrane fuel cell(PEMFC),However,severe mass transfer polarization loss resulting in fuel cell performance decline will be encountered in ultra-low Pt PEMFC.In this work,mild oxidized multiwalled carbon nanotubes(mMWCNT)were adopted to construct the catalyst layer,and by varying the loading of carbon nanotubes,the catalyst layer structure was optimized.A high peak power density of 1.23 W·cm^(-2) for the MEA with mMWCNT was obtained at an ultra-low loading of 120μg·cm^(-2) Pt/PtRu(both cathode and anode),which was 44.7%higher than that of MEA without mMWCNT.Better catalyst dispersion,low charge transfer resistance,more porous structure and high hydrophobicity of catalyst layer were ascribed for the reasons of the performance improvement.展开更多
Pulverized coal combustion technology with preheating solid fuel in a circulating fluidized bed was used for the combustion test of ultra-low volatile carbon-based fuel.This paper first validated the feasibility and a...Pulverized coal combustion technology with preheating solid fuel in a circulating fluidized bed was used for the combustion test of ultra-low volatile carbon-based fuel.This paper first validated the feasibility and advantages of applying the combustion technology to this kind of fuel.The carbon-based fuel could achieve a stable preheating process in this test system.After the preheating,the apparent sensible heat of the fuel was significantly increased.This provided a necessary condition for the stable ignition and efficient combustion of the carbon-based fuel in the post-combustion chamber.The relative proportions of CO,H2,and CH4 in preheated coal gas were very low,and the effect of high-temperature coal gas at the entrance of the post-combustion chamber was greatly impaired,indicating that the combustion process in post-combustion chamber was mainly the combustion of preheated char.At the same time,the strong reducing atmosphere in the circulating fluidized bed also facilitated the reduction of fuel-nitrogen into N2,which resulted in low NOx emissions.On this basis,with the combination of preheating combustion technology and air-staging combustion technology,the NOx emissions had drastically decreased when the burnout air distribution position moved down or varied from a single-layer distribution to a multi-layer distribution system.The lowest original NOx emissions were 90.6 mg/m3(at 6%O2),and the combustion efficiency exceeded 97%,which ultimately achieved efficient and clean combustion of ultra-low volatile carbon-based fuel.展开更多
In this paper, pyrolysis of Indonesian oil sands(IOS) was investigated by two different heating methods to develop a better understanding of the microwave-assisted pyrolysis. Thermogravimetric analysis was conducted t...In this paper, pyrolysis of Indonesian oil sands(IOS) was investigated by two different heating methods to develop a better understanding of the microwave-assisted pyrolysis. Thermogravimetric analysis was conducted to study the thermal decomposition behaviors of IOS, showing that 550 °C might be the pyrolysis final temperature. A explanation of the heat–mass transfer process was presented to demonstrate the influence of microwave-assisted pyrolysis on the liquid product distribution. The heat–mass transfer model was also useful to explain the increase of liquid product yield and heavy component content at the same heating rate by two different heating methods. Experiments were carried out using a fixed bed reactor with and without the microwave irradiation. The results showed that liquid product yield was increased during microwave induced pyrolysis,while the formation of gas and solid residue was reduced in comparison with the conventional pyrolysis. Moreover, the liquid product characterization by elemental analysis and GC–MS indicated the significant effect on the liquid chemical composition by microwave irradiation. High polarity substances(ε N 10 at 25 °C), such as oxyorganics were increased, while relatively low polarity substances(ε b 2 at 25 °C), such as aliphatic hydrocarbons were decreased, suggesting that microwave enhanced the relative volatility of high polarity substances. The yield improvement and compositional variations in the liquid product promoted by the microwave-assisted pyrolysis deserve the further exploitation in the future.展开更多
文摘A new type of power supply which was called oxy-fuel combustion power plant was introduced to reduce greenhouse gasses emission. In this paper the volatile emission characteristic of pulverized coal is studied under air atmosphere and oxy-fuel atmosphere. Combustion experiments of Datong bituminous coal were carried out in a wire mesh reactor at heating rates of 1 K/s, 10 K/s and 1000 K/s respectively under air and O2/CO2 atmosphere conditions in order to investigate the volatile emission characteristic. The concentrations of volatile (mainly CO and CH4) emission were on-line measured by infrared gas analyzer. It was indicated that the concentrations of CO and CH4 in O2/CO2 atmosphere were higher than those in air. The direct oxidation of carbon and gasification reaction between carbon and CO2 are the main causes of the increased amount of CO. The higher concentration of CO2 also results in the increased amount of CH4 in O2/CO2 conditions.
基金finically supported by the National Natural Science Foundation of China(22075055)the Guangxi Science and Technology Project(AB16380030)the Innovation Project of Guangxi Graduate Education(YCSW2020052)。
文摘Reducing a Pt loading with improved power output and durability is essential to promote the large-scale application of proton exchange membrane fuel cells(PEMFCs).To achieve this goal,constructing optimized structure of catalyst layers with efficient mass transportation channels plays a vital role.Herein,PEMFCs with order-structured cathodic electrodes were fabricated by depositing Pt nanoparticles by Ebeam onto vertically aligned carbon nanotubes(VACNTs)growth on Al foil via plasma-enhanced chemical vapor deposition.Results demonstrate that the proportion of hydrophilic Pt-deposited region along VACNTs and residual hydrophobic region of VANCTs without Pt strongly influences the cell performance,in particular at high current densities.When Pt nanoparticles deposit on the top depth of around 600 nm on VACNTs with a length of 4.6μm,the cell shows the highest performance,compared with others with various lengths of VACNTs.It delivers a maximum power output of 1.61 W cm^(-2)(H_(2)/O_(2),150 k Pa)and 0.79 W cm^(-2)(H_(2)/Air,150 k Pa)at Pt loading of 50μg cm^(-2),exceeding most of previously reported PEMFCs with Pt loading of<100μg cm^(-2).Even though the Pt loading is down to 30μg cm^(-2)(1.36 W cm^(-2)),the performance is also better than 100μg cm^(-2)(1.24 W cm^(-2))of commercial Pt/C,and presents better stability.This excellent performance is critical attributed to the ordered hydrophobic region providing sufficient mass passages to facilitate the fast water drainage at high current densities.This work gives a new understanding for oxygen reduction reaction occurred in VACNTs-based ordered electrodes,demonstrating the most possibility to achieve a substantial reduction in Pt loading<100μg cm^(-2) without sacrificing in performance.
基金financial supports by the National Key Research and Development Program of China(2019YFB1504500)the National Natural Science Foundation of China(22078031,91834301,21761162015)+1 种基金the Fundamental Research Funds for the Central Universities,CQU(2020CDJQY-A032,2020CDJLHZZ064)the Natural Science Foundation of Chongqing(cstc2020jcyjmsxmX0637)。
文摘Reducing the loading of noble Pt-based catalyst is vital for the commercialization of proton exchange membrane fuel cell(PEMFC),However,severe mass transfer polarization loss resulting in fuel cell performance decline will be encountered in ultra-low Pt PEMFC.In this work,mild oxidized multiwalled carbon nanotubes(mMWCNT)were adopted to construct the catalyst layer,and by varying the loading of carbon nanotubes,the catalyst layer structure was optimized.A high peak power density of 1.23 W·cm^(-2) for the MEA with mMWCNT was obtained at an ultra-low loading of 120μg·cm^(-2) Pt/PtRu(both cathode and anode),which was 44.7%higher than that of MEA without mMWCNT.Better catalyst dispersion,low charge transfer resistance,more porous structure and high hydrophobicity of catalyst layer were ascribed for the reasons of the performance improvement.
基金the support of the National Key Research and Development Program of China(2017YFB0602005)
文摘Pulverized coal combustion technology with preheating solid fuel in a circulating fluidized bed was used for the combustion test of ultra-low volatile carbon-based fuel.This paper first validated the feasibility and advantages of applying the combustion technology to this kind of fuel.The carbon-based fuel could achieve a stable preheating process in this test system.After the preheating,the apparent sensible heat of the fuel was significantly increased.This provided a necessary condition for the stable ignition and efficient combustion of the carbon-based fuel in the post-combustion chamber.The relative proportions of CO,H2,and CH4 in preheated coal gas were very low,and the effect of high-temperature coal gas at the entrance of the post-combustion chamber was greatly impaired,indicating that the combustion process in post-combustion chamber was mainly the combustion of preheated char.At the same time,the strong reducing atmosphere in the circulating fluidized bed also facilitated the reduction of fuel-nitrogen into N2,which resulted in low NOx emissions.On this basis,with the combination of preheating combustion technology and air-staging combustion technology,the NOx emissions had drastically decreased when the burnout air distribution position moved down or varied from a single-layer distribution to a multi-layer distribution system.The lowest original NOx emissions were 90.6 mg/m3(at 6%O2),and the combustion efficiency exceeded 97%,which ultimately achieved efficient and clean combustion of ultra-low volatile carbon-based fuel.
基金Supported by the National Key Research and Development Program of China(2016YFB0301800)the partial support by The Royal Society International Exchange Award(IE161344)the State Scholarship Fund of China Scholarship Council(CSC)(201706255020)
文摘In this paper, pyrolysis of Indonesian oil sands(IOS) was investigated by two different heating methods to develop a better understanding of the microwave-assisted pyrolysis. Thermogravimetric analysis was conducted to study the thermal decomposition behaviors of IOS, showing that 550 °C might be the pyrolysis final temperature. A explanation of the heat–mass transfer process was presented to demonstrate the influence of microwave-assisted pyrolysis on the liquid product distribution. The heat–mass transfer model was also useful to explain the increase of liquid product yield and heavy component content at the same heating rate by two different heating methods. Experiments were carried out using a fixed bed reactor with and without the microwave irradiation. The results showed that liquid product yield was increased during microwave induced pyrolysis,while the formation of gas and solid residue was reduced in comparison with the conventional pyrolysis. Moreover, the liquid product characterization by elemental analysis and GC–MS indicated the significant effect on the liquid chemical composition by microwave irradiation. High polarity substances(ε N 10 at 25 °C), such as oxyorganics were increased, while relatively low polarity substances(ε b 2 at 25 °C), such as aliphatic hydrocarbons were decreased, suggesting that microwave enhanced the relative volatility of high polarity substances. The yield improvement and compositional variations in the liquid product promoted by the microwave-assisted pyrolysis deserve the further exploitation in the future.
