The mechanisms of thermal solidification agent promoting steam diversion in heavy oil reservoirs

At high cycles of steam huff&puff,oil distribution in reservoirs becomes stronger heterogeneity due to steam channeling.Thermal solidification agent can be used to solve this problem.Its solution is a lowviscosity liquid at normal temperature,but it can be solidified above 80℃.The plugging degree is up to 99%at 250℃.The sweep efficiency reaches 59.2%,which is 7.3%higher than pure steam injection.In addition,simultaneous injection of viscosity reducer and/or nitrogen foams can further enhance oil recovery.The mechanism of this technology depends on its strong plugging ability,which changes the flowing pattern of steam to effectively mobilize remaining oil.Viscosity reducer and nitrogen foams further expand the sweep range and extends the effective period.Therefore,thermal solidification agent can plug steam channeling paths and adjust steam flowing direction to significantly enhance oil recovery at high cycles of steam huff&puff.

A Real-time Prediction System for Molecular-level Information of Heavy Oil Based on Machine Learning

Acquiring accurate molecular-level information about petroleum is crucial for refining and chemical enterprises to implement the“selection of the optimal processing route”strategy.With the development of data prediction systems represented by machine learning,it has become possible for real-time prediction systems of petroleum fraction molecular information to replace analyses such as gas chromatography and mass spectrometry.However,the biggest difficulty lies in acquiring the data required for training the neural network.To address these issues,this work proposes an innovative method that utilizes the Aspen HYSYS and full two-dimensional gas chromatography-time-of-flight mass spectrometry to establish a comprehensive training database.Subsequently,a deep neural network prediction model is developed for heavy distillate oil to predict its composition in terms of molecular structure.After training,the model accurately predicts the molecular composition of catalytically cracked raw oil in a refinery.The validation and test sets exhibit R2 values of 0.99769 and 0.99807,respectively,and the average relative error of molecular composition prediction for raw materials of the catalytic cracking unit is less than 7%.Finally,the SHAP(SHapley Additive ExPlanation)interpretation method is used to disclose the relationship among different variables by performing global and local weight comparisons and correlation analyses.

An Integrated Optimization Method for CO_(2) Pre-Injection during Hydraulic Fracturing in Heavy Oil Reservoirs

CO_(2) pre-injection during hydraulic fracturing is an important method for the development of medium to deep heavy oil reservoirs.It reduces the interfacial tension and viscosity of crude oil,enhances its flowability,maintains reservoir pressure,and increases reservoir drainage capacity.Taking the Badaowan Formation as an example,in this study a detailed three-dimensional geomechanical model based on static data from well logging interpretations is elaborated,which can take into account both vertical and horizontal geological variations and mechanical characteristics.A comprehensive analysis of the impact of key construction parameters on Pre-CO_(2) based fracturing(such as cluster spacing and injection volume),is therefore conducted.Thereafter,using optimized construction parameters,a non-structured grid for dynamic development prediction is introduced,and the capacity variations of different production scenarios are assessed.On the basis of the simulation results,reasonable fracturing parameters are finally determined,including cluster spacing,fracturing fluid volume,proppant concentration,and well spacing.

Heavy Metal Levels and Ecological Risk in Crude Oil-Contaminated Soils from Okpare-Olomu, Niger Delta, Nigeria

Crude oil spills have inflicted extensive disruption upon the Niger Delta ecosystem, resulting in crop loss and severe environmental damage. Such spills exacerbate heavy metal concentration within soil due to the presence of metallic ions. The Okpare-Olomu community has borne the brunt of crude oil pollution from illicit bunkering, sabotage, and equipment malfunction. This study targets an evaluation of ecological hazards linked to heavy metals (HMs) in crude oil impacted agriculturally soils within Okpare-Olomu in Ughelli South LGA of Delta State. In this study, 24 topsoil samples were obtained from areas affected by crude oil pollution;the heavy metal content was evaluated through atomic absorption spectrometry. The concentration ranges for HMs (mg/kg) in soil were: 24.1 - 23,174 (Cu);0.54 - 37.1 (Cd);9.05 - 54 (Cr);12 - 174 (Ni);18.5 - 8611 (Pb);and 148 - 9078 (Zn) at a soil depth of 0 - 15 cm. Notably, metal concentrations were recorded to be above permissible World Health Organization limits. Predominantly, Zn and Pb recorded higher heavy metal concentration when compared to other heavy metals analysed, notably at sampling points PT7 through PT24. Zinc and Pb contamination exhibited highly significant contamination factors, and contamination severity was evidenced across all sample points, signifying a grave risk level. Pollution load indices indicated pervasive extreme pollution levels. Geoaccumulation indices signaled moderate to strong pollution, mainly by Pb and Zn. Ecological risk assessments revealed variable levels of heavy metal contamination, from low to very high, with potential ecological risk reflecting markedly elevated levels. This study underscores the imperative for soil remediation to rectify ecological imbalances in agriculturally affected soil constituents.

Study of steam heat transfer enhanced by CO_(2) and chemical agents: In heavy oil production

Steam flooding with the assistance of carbon dioxide (CO_(2)) and chemicals is an effective approach for enhancing super heavy oil recovery. However, the promotion and application of CO_(2) and chemical agent-assisted steam flooding technology have been restricted by the current lack of research on the synergistic effect of CO_(2) and chemical agents on enhanced steam flooding heat transfer. The novel experiments on CO_(2)–chemicals cooperate affected steam condensation and seepage were conducted by adding CO_(2) and two chemicals (sodium dodecyl sulfate (SDS) and the betaine temperature-salt resistant foaming agent ZK-05200).According to the experimental findings, a “film” formed on the heat-transfer medium surface following the co-injection of CO_(2) and the chemical to impede the steam heat transfer, reducing the heat transfer efficiency of steam, heat flux and condensation heat transfer coefficient. The steam seepage experiment revealed that the temperature at the back end of the sandpack model was dramatically raised by 3.5–12.8 °C by adding CO_(2) and chemical agents, achieving the goal of driving deep-formation heavy oil. The combined effect of CO_(2) and SDS was the most effective for improving steam heat transfer, the steam heat loss was reduced by 6.2%, the steam condensation cycle was prolonged by 1.3 times, the condensation heat transfer coefficient was decreased by 15.5%, and the heavy oil recovery was enhanced by 9.82%. Theoretical recommendations are offered in this study for improving the CO_(2)–chemical-assisted steam flooding technique.

Petrophysical parameters inversion for heavy oil reservoir based on a laboratory-calibrated frequency-variant rock-physics model

Heavy oil has high density and viscosity, and exhibits viscoelasticity. Gassmann's theory is not suitable for materials saturated with viscoelastic fluids. Directly applying such model leads to unreliable results for seismic inversion of heavy oil reservoir. To describe the viscoelastic behavior of heavy oil, we modeled the elastic properties of heavy oil with varying viscosity and frequency using the Cole-Cole-Maxwell (CCM) model. Then, we used a CCoherent Potential Approximation (CPA) instead of the Gassmann equations to account for the fluid effect, by extending the single-phase fluid condition to two-phase fluid (heavy oil and water) condition, so that partial saturation of heavy oil can be considered. This rock physics model establishes the relationship between the elastic modulus of reservoir rock and viscosity, frequency and saturation. The viscosity of the heavy oil and the elastic moduli and porosity of typical reservoir rock samples were measured in laboratory, which were used for calibration of the rock physics model. The well-calibrated frequency-variant CPA model was applied to the prediction of the P- and S-wave velocities in the seismic frequency range (1–100 Hz) and the inversion of petrophysical parameters for a heavy oil reservoir. The pre-stack inversion results of elastic parameters are improved compared with those results using the CPA model in the sonic logging frequency (∼10 kHz), or conventional rock physics model such as the Xu-Payne model. In addition, the inversion of the porosity of the reservoir was conducted with the simulated annealing method, and the result fits reasonably well with the logging curve and depicts the location of the heavy oil reservoir on the time slice. The application of the laboratory-calibrated CPA model provides better results with the velocity dispersion correction, suggesting the important role of accurate frequency dependent rock physics models in the seismic prediction of heavy oil reservoirs.

Molecular composition of naphthenic acids in a Chinese heavy crude oil and their impacts on oil viscosity

Most heavy crude oils underwent biodegradation and generated a significant amount of naphthenic acids. Naphthenic acids are polar compounds with the carboxylic group and are considered as a major factor affecting the oil viscosity. However, the relationship between the molecular composition of naphthenic acids and oil viscosity is not well understood. This study examined a “clean” heavy oil with low contents of heteroatoms but had a high content of naphthenic acids. Naphthenic acids were fractionated by distillation and caustic extraction. The molecular composition was characterized by high-resolution Orbitrap mass spectrometry. It was found that the 2- and 3-ring naphthenic monoacids with 15–35 carbon atoms are dominant components of the acid fractions;the caustic extraction is capable of isolating naphthenic acids with less than 35 carbons, which is equivalent to the upper limit of the distillable components, but not those in the residue fraction;the total acid number of the heavy distillates is higher than that of the residue fraction;the viscosity of the distillation fraction increases exponentially with an increased boiling point of the distillates. Blending experiments indicates that there is a strong correlation between the oil viscosity and acids content, although the acid content is only a few percent of the total oil.

Rapid accuracy determining DNA purity and concentration in heavy oils by spectrophotometry methods

DNA analysis is the core of biotechnology applied in petroleum resources and engineering. Traditionally accurate determination of DNA purity and concentration by spectrometer is the first and critical step for downstream molecular biology research. In this study, three different spectrophotometry methods, BPM, NDTT and NPMTTZ were compared for their performance in determining DNA concentration and purity in 32 oil samples, and molecule methods like quantitative real-time PCR (qPCR) and high-throughput sequence were also performed to help assess the accuracy of the three methods in determining DNA concentration and purity. For ordinary heavy oil (OHO), extra heavy oil (EHO) and super heavy oil (SHO), the characteristics of high viscosity (η), density (ρ) and resin plus asphaltene content will affect the DNA extraction and UV determination. The DNA concentration was decreased as density increased: OHO (11.46 ± 18.34 ng/μL), EHO (6.68 ± 9.67 ng/μL) and SHO (6.20 ± 7.83 ng/μL), and the DNA purity was on the reverse: OHO (1.31 ± 0.27), EHO (1.54 ± 0.20), and SHO (1.83 ± 0.32). The results suggest that spectrophotometry such as BPM and NPMTTZ are qualitatively favorite methods as the quick non-consumable methods in determining DNA concentration and purity of medium oil and heavy oil.

Mechanism investigation of steam flooding heavy oil by comprehensive molecular characterization

Steam flooding is a widely used technique to enhance oil recovery of heavy oil.Thermal viscosity reduction and distillation effect are considered as two main displacement mechanisms in steam flooding process.However,the molecular composition understanding and contribution for oil production are still unclear.In this study,the composition analysis of the heavy oil was investigated in the core scale steam flooding process with the temperature from 120 to 280℃.The crude oil,produced oils and residual oils were characterized comprehensively by gas chromatography and high-resolution mass spectrometry.It is found that steam flooding preferentially extracts aromatics and remains more resins in the residual oil.Viscosity reduction is the dominant mechanism when steam is injected at a low temperature.Large molecular heteroatoms with high carbon number and high double bond equivalent(DBE)are eluted into the produced oil,while compounds with low carbon number and low DBE are remained in the residual oil.As the steam temperature rises,the increased distillation effect results in the extraction of light hydrocarbons from the residual oil to the produced oil.More small heteroatoms with low carbon number and low DBE enter into the produced oil,especially in the none water cut stage.The compositional difference of produced oils is characterized in DBE versus carbon number distribution of the N and O containing compound classes.This work uses a variety of composition analysis methods to clarify the steam flooding mechanism and provides a novel understanding of steam flooding mechanisms with various temperatures and production stages from the molecular perspective.

Investigation of feasibility of alkali-cosolvent flooding in heavy oil reservoirs

Cold production is a challenge in the case of heavy oil because of its high viscosity and poor fluidity in reservoir conditions.Alkali-cosolvent-polymer flooding is a type of microemulsion flooding with low costs and possible potential for heavy oil reservoirs.However,the addition of polymer may cause problems with injection in the case of highly viscous oil.Hence,in this study the feasibility of alkali-cosolvent(AC)flooding in heavy oil reservoirs was investigated via several groups of experiments.The interfacial tension between various AC formulations and heavy crude oil was measured to select appropriate formulations.Phase behavior tests were performed to determine the most appropriate formulation and conditions for the generation of a microemulsion.Sandpack flooding experiments were carried out to investigate the displacement efficiency of the selected Ac formulation.The results showed that the interfacial tension between an AC formulation and heavy oil could be reduced to below 1o-3 mN/m but differed greatly between different types of cosolvent.A butanol random polyether series displayed good performance in reducing the water-oil interfacial tension,which made it possible to form a Type Il microemulsion in reservoir conditions.According to the results of the phase behavior tests,the optimal salinity for different formulations with four cosolvent concentrations(0.5 wt%,1 wt%,2 wt%,and 3 wt%)was 4000,8000,14000,and 20000 ppm,respectively.The results of rheological measurements showed that Type Ill microemulsion had a viscosity that was ten times that of water.The results of sandpack flooding experiments showed that,in comparison with waterflooding,the injection of a certain Ac formulation slug could reduce the injection pressure.The pressure gradient during waterflooding and AC flooding was around 870 and 30-57 kPa/m,respectively.With the addition of an AC slug,the displacement efficiency was 30%-50%higher than in the case of waterflooding.

Comparative pyrolysis kinetics of heavy oil and its SARA fractions using distributed activation energy model

The pyrolysis behaviors of Qingdao vacuum residue(QD-VR)and its SARA(saturates,aromatics,reins,and asphaltenes)fractions were evaluated by thermo-gravimetric with mass spectrometer(TG-MS).The pyrolysis kinetics were determined by Friedman,one-parallel and four-parallel distributed activation energy model(DAEM),respectively.The results indicated that the pyrolysis behavior of QD-VR was similar to that of aromatics.For saturates,the release of H_(2),CH_(4),CO,and CO_(2) occurred in 80-400℃,while the temperature range for QD-VR and other fractions is 200-800℃.The average activation energy(Ea)via Friedman method was 179.72 kJ/mol and increased with the conversion ratio.One-parallel Gaussian DAEM was more suitable to describe the pyrolysis process of the single SARA fractions,while four-parallel Gaussian DAEM was more suitable to describe the pyrolysis process of heavy oil.Furthermore,comparing the weighted E_(a) from one-parallel(227.64 kJ/mol)and four-parallel Gaussian DAEM(204.63 kJ/mol),the results suggested that during pyrolysis process of heavy oil,there was an interaction between the SARA fractions,which could reduce the E_(a) of heavy oil pyrolysis.Specifically,during heavy oil pyrolysis,resins and asphaltenes could increase the E_(a) of saturates and aromatics,while saturates and aromatics could decrease the E_(a) of resins and asphaltenes.

Molecular composition of low-temperature oxidation products of the heavy oil

Low-temperature oxidation(LTO)is the main reaction that affects fuel formation in the in-situ combustion process,which has important significance for the subsequent combustion propulsion and the successful extraction of crude oil.In this study,heavy oil was subjected to LTO reactions at different temperatures.Three types of reaction products with varying oxidation depths were characterized in terms of the number of oxygen atoms and the polarity of the molecule to reveal the low-temperature oxidation process of the heavy oil.Ketone compounds and acid polyoxides in the oil phase and deep oxidation products with a higher number of oxygen atoms in the coke were identified with increasing oxidation depth.The experimental results showed that the oxidation reaction of the heavy oil changed from kinetic-controlled to diffusion-controlled in the open oxidation system of the heavy oil as the oxidation depth increased.The oxidation reaction of the oil phase reached a maximum and stable value in oxygen content.The molecular compositions of the ketone compound and acid polyoxide did not change significantly with further increase in reaction temperature.The molecular compositions of the deep oxidation products with a higher number of oxygen atoms in the coke phase changed significantly.The coke precursor molecules with a lower oxygen content and condensation degree participated in the coke formation,and the oxidation reaction pathway and the complexity of the oxidation product component also increased.

Study on the Catalytic Reforming Law of Solid-Phase Carbon and Nitrogen Sources Loaded with MnO_(2)at Low Temperatures in Tahe Heavy Oil

MnO_(2)/Melem composites were synthesized with MnO_(2)nanoparticles loaded onto the Melem using the hydrothermal method.As raw materials for C and N carriers,Melem was prepared from melamine roasted at 354℃,and KMnO_(4)as a raw material for Mn,MnO_(2)nanoparticles were prepared using the hydrothermal synthesis of KMnO_(4).Scanning electron microscopy(SEM),transmission electron microscopy(TEM),X-ray diffraction(XRD),and a laser particle size analyzer were used for structural characterization,and the catalytic oxidation performance of the heavy oil was investigated at different reaction temperatures(100℃to 180℃)using MnO_(2)/Melem with an oxidant and donor protonic acid.The results showed that the synthesizedβ-MnO_(2)nanoparticles were successfully loaded onto the Melem surface;the oil samples before and after the reaction at different temperatures were subjected to SARA analysis using Fourier transform infrared(FT-IR),elemental analysis,gas chromatography-mass spectrometry(GC-MS)and viscosity tests,respectively.It was determined that the hydrocarbons in the crude oil were converted to heavy mass by oxidation reactions with the oxidant mainly through a low-temperature oxidation process below 140℃in the heavy oil when the temperature exceeds 140℃,in addition to the oxidation reaction with the oxidant,a cleavage reaction in the carbon chain occurs to form hydrocarbon substances with lower molecular weights.

Enhancing Heavy Crude Oil Flow in Pipelines through Heating-Induced Viscosity Reduction in the Petroleum Industry

The process of transporting crude oil across pipelines is one of the most critical aspects of the midstream petroleum industry.In the present experimental work,the effect of temperature,pressure drop,and pipe diameter on the flow rate of heavy crude oil have been assessed.Moreover,the total discharge and energy losses have been evaluated in order to demonstrate the improvements potentially achievable by using solar heating method replacing pipe,and adjusting the value of the initial pressure difference.Crude oil of API=20 has been used for the experiments,with the studied pipelines sections connecting the separator unit to the storage tank operating at a temperature of 25℃-100℃,pressure drop of 3,4,5,and 6 kg/cm^(2),and with pipe diameter of 4,6,and 8 in.The results show that on increasing the temperature and/or the pressure drop,the flow rate through the pipeline becomes higher,thus raising the total pumping energy(as the pipe diameter increase),while energy losses increase from the last separator to the storage tank in the field.A pipe diameter increase can also produce a growth of the total pumping energy(i.e.,energy losses increase).The results of the present analysis suggest that employing an optimal temperature(50℃)is needed to ensure good performance.

Optimization of the Plugging Agent Dosage for High Temperature Salt Profile Control in Heavy Oil Reservoirs

After steam discharge in heavy oil reservoirs,the distribution of temperature,pressure,and permeability in different wells becomes irregular.Flow channels can easily be produced,which affect the sweep efficiency of the oil displacement.Previous studies have shown that the salting-out plugging method can effectively block these channels in high-temperature reservoirs,improve the suction profile,and increase oil production.In the present study,the optimal dosage of the plugging agent is determined taking into account connection transmissibility and inter-well volumes.Together with the connectivity model,a water flooding simulation model is introduced.Moreover,a non-gradient stochastic disturbance algorithm is used to obtain the optimal plugging agent dosage,which provides the basis for the high-temperature salting-out plugging agent adjustment in the field.

Study on the in situ desulfurization and viscosity reduction of heavy oil over MoO_(3)–ZrO_(2)/HZSM-5 catalyst

Heavy oil is characterized by high viscosity.High viscosity makes it challenging to recover and transport.HZSM-5,MoO_(3)/HZSM-5,ZrO_(2)/HZSM-5 and MoO_(3)–ZrO_(2)/HZSM-5 catalysts were developed to promote in situ desulfurization and viscosity reduction of heavy oil.The physical and chemical properties of catalysts were characterized by XPS,XRD,TEM,NH3-TPD,etc.The effects of temperature,catalyst type and addition amount on viscosity and composition of heavy oil were evaluated.The results showed that the presence of MoO_(3)–ZrO_(2)/HZSM-5 nanoparticles during aquathermolysis could improve the oil quality by reducing the heavy fractions.It reduced viscosity by 82.56%after the reaction at 280℃ and catalyst addition of 1 wt%.The contents of resins and asphaltic in the oil samples were 5.69%lower than that in the crude oil.Sulfur content decreased from 1.45%to 1.03%.The concentration of H2S produced by the reaction was 2225 ppm.The contents of sulfur-containing functional groups sulfoxide and sulfone sulfur in the oil samples decreased by 19.92%after the catalytic reaction.The content of stable thiophene sulfur increased by 5.71%.This study provided a basis for understanding the mechanism of heavy oil desulfurization and viscosity reduction.

Thermomechanical and Hydrous Effect of Heavy Fuel Oil in a Building Material Based on Silty Clayey Soil

This study focuses on the use of heavy fuel oil in construction in Burkina Faso.Mixed with silty and/or clay soil,it is used as a coating to reinforce the walls of raw soil constructions which are very sensitive to water.The interest of this paper is to shed light on the thermomechanical and above all water effects of heavy fuel oil on a sample of silty clayey soil.To achieve this,we used heavy fuel oil added in different proportions to silty clayey soil,to make sample of bricks on which tests were carried out.At the end of the experimental tests carried out on materials made(bricks)with our soil sample,it appears that heavy fuel oil moderately reduces the mechanical resistance of bricks and slightly increases thermal diffusion through them.On the contrary,we note a very good water resistance of the bricks thanks to the heavy fuel oil,in particular their water absorption by capillarity.This confirms that the mixture of heavy fuel oil and a silty-clayey soil used as a coating makes it possible to prevent the infiltration of water into the walls of raw soil constructions.However,its use as a construction material does not guarantee very good mechanical resistance,and slightly increases thermal diffusion.

Effects of Different Heavy Crude Oil Fractions on the Stability of Oil-in-water Emulsions —— Isolation of functional fractions from heavy crude oil and study of their properties

The functional fractions (acid, basic, amphoteric and neutral fractions) are isolated from the Liaohe Du-84 heavy crude oil and Shengli Gudao Kenxi heavy crude oil by ion-exchange chromatography, but the conventional fractions (saturates, aromatics, resins and asphaltenes) are also isolated from the heavy crude oil. These components have been characterized by spectroscopic methods (FT-IR), namely acid number, basic nitrogen number, ultimate analysis and molecular weight measurements using vapor pressure osmometry (VPO). The ion-exchange chromatography method based on separation by a functional group induces a little change on the nature of the crudes and reasonable mass balances can be easily obtained.

Synthesis and evaluation of an oil-soluble viscosity reducer for heavy oil

To reduce the viscosity of highly-viscous oil of the Tahe oilfield （Xinjiang,China）,an oilsoluble polybasic copolymer viscosity reducer for heavy oil was synthesized using the orthogonal method.The optimum reaction conditions are obtained as follows：under the protection of nitrogen,a reaction time of 9 h,monomer mole ratio of reaction materials of 3：2：2 （The monomers are 2-propenoic acid,docosyl ester,maleic anhydride and styrene,respectively）,initiator amount of 0.8% （mass percent of the sum of all the monomers） and reaction temperature of 80 oC.This synthesized viscosity reducer is more effective than commercial viscosity reducers.The rate of viscosity reduction reached 95.5% at 50 oC.Infrared spectra （IR） and interfacial tensions of heavy oil with and without viscosity reducer were investigated to understand the viscosity reduction mechanism.When viscosity reducer is added,the molecules of the viscosity reducer are inserted amongst the molecules of crude oil,altering the original intermolecular structure of crude oil and weakening its ability to form hydrogen bonds with hydroxyl or carboxyl groups,so the viscosity of crude oil is reduced.Field tests of the newly developed oil-soluble viscosity reducer was carried out in the Tahe Oilfield,and the results showed that 44.5% less light oil was needed to dilute the heavy oil to achieve the needed viscosity.

Heavy Oil and Oil Sands:Global Distribution and Resource Assessment

Global recoverable resources of heavy oil and oil sands have been assessed by CNPC using a geology-based assessment method combined with the traditional volumetric method, spatial interpolation method, parametric-probability method etc. The most favourable areas for exploration have been selected in accordance with a comprehensive scoring system. The results show:(1) For geological resources, CNPC estimate 991.18 billion tonnes of heavy oil and 501.26 billion tonnes of oil sands globally, of which technically recoverable resources of heavy oil and oil sands comprise 126.74 billion tonnes and 64.13 billion tonnes respectively. More than 80% of the resources occur within Tertiary and Cretaceous reservoirs distributed across 69 heavy oil basins and 32 oil sands basins. 99% of recoverable resources of heavy oil and oil sands occur within foreland basins, passive continental-margin basins and cratonic basins.(2) Since residual hydrocarbon resources remain following large-scale hydrocarbon migration and destruction, heavy oil and oil sands are characterized most commonly by late hydrocarbon accumulation, the same basin types and source-reservoir conditions as for conventional hydrocarbon resources, shallow burial depth and stratabound reservoirs.(3) Three accumulation models are recognised, depending on basin type: degradation along slope; destruction by uplift; and migration along faults.(4) In addition to mature exploration regions such as Canada and Venezuela, the Volga-Ural Basin and the Pre-Caspian Basin are less well-explored and have good potential for oil-sand discoveries, and it is predicted that the Middle East will be an important region for heavy oil development.