Sandwich structures with tapered tubes as core:A quasi-static investigation

In this article,the experimental and finite element analysis is utilized to investigate the quasi-static compression features of sandwich constructions built with tapered tubes.3D printing technology was utilized to create the hollow centers of the tapering tubes,with and without corrugations.The results demonstrate that the energy absorption(EA)and specific energy absorption(SEA)of the single corrugated tapered tube sandwich are 51.6% and 19.8% higher,respectively,than those of the conical tube sandwich.Furthermore,the results demonstrate that energy absorbers can benefit from corrugation in order to increase their efficiency.Additionally,the tapered corrugated tubes'resistance to oblique impacts was studied.Compared to a straight tube,the tapered tube is more resistant to oblique loads and has a lower initial peak crushing force(PCF),according to numerical simulations.After conducting a parametric study,it was discovered that the energy absorption performance of the sandwich construction is significantly affected by the amplitude,number of corrugations,and wall thickness.EA and SEA of DTS with corrugation number of 8 increased by 17.4%and 29.6%,respectively,while PCF decreased by 9.2% compared to DTS with corrugation number of 10.

Ballistic performances of the hourglass lattice sandwich structures under high-velocity fragments

In this paper,the numerical simulation method is used to study the ballistic performances of hourglass lattice sandwich structures with the same mass under the vertical incidence of fragments.Attention is paid to elucidating the influences of rod cross-section dimensions,structure height,structure layer,and rod inclination angle on the deformation mode,ballistic performances,and ability to change the ballistic direction of fragments.The results show that the ballistic performances of hourglass lattice sandwich structures are mainly affected by their structural parameters.In this respect,structural parameters optimization of the hourglass lattice sandwich structures enable one to effectively improve their ballistic limit velocity and,consequently,ballistic performances.

Lignin‐derived carbon with pyridine N‐B doping and a nanosandwich structure for high and stable lithium storage

Biomass‐derived carbon is a promising electrode material in energy storage devices.However,how to improve its low capacity and stability,and slow diffusion kinetics during lithium storage remains a challenge.In this research,we propose a“self‐assembly‐template”method to prepare B,N codoped porous carbon(BN‐C)with a nanosandwich structure and abundant pyridinic N‐B species.The nanosandwich structure can increase powder density and cycle stability by constructing a stable solid electrolyte interphase film,shortening the Li^(+) diffusion pathway,and accommodating volume expansion during repeated charging/discharging.The abundant pyridinic N‐B species can simultaneously promote the adsorption/desorption of Li^(+)/PF_(6)^(−) and reduce the diffusion barrier.The BN‐C electrode showed a high lithium‐ion storage capacity of above 1140 mAh g^(−1) at 0.05 A g^(−1) and superior stability(96.5% retained after 2000 cycles).Moreover,owing to the synergistic effect of the nanosandwich structure and pyridinic N‐B species,the assembled symmetrical BN‐C//BN‐C full cell shows a high energy density of 234.7Wh kg^(−1),high power density of 39.38 kW kg−1,and excellent cycling stability,superior to most of the other cells reported in the literature.As the density functional theory simulation demonstrated,pyridinic N‐B shows enhanced adsorption activity for Li^(+) and PF_(6)^(−),which promotes an increase in the capacity of the anode and cathode,respectively.Meanwhile,the relatively lower diffusion barrier of pyridinic N‐B promotes Li^(+) migration,resulting in good rate performance.Therefore,this study provides a new approach for the synergistic modulation of a nanostructure and an active site simultaneously to fabricate the carbon electrode material in energy storage devices.

Sandwich Structure-like Meshes Fabricated via Electrospinning for Controllable Release of Zoledronic Acid

Novel sandwich structure-like nanofiber multilayered meshes were fabricated via electrospinning. The purpose of the present work was to control zoledronic acid release via the novel structure of sandwich structure-like meshes. The in vitro release experiments reveal that the drug release speed and initial burst release were controllable by adjusting the thicknesses of electrospun barrier mesh and drug-loaded mesh. Compared with those of other drug delivery systems, the main advantages of the sandwich structure-like fiber meshes are facile preparation conditions and the generality for hydrophobic and hydrophilic pharmaceuticals.

Effects of electric/magnetic impact on the transient fracture of interface crack in piezoelectric-piezomagnetic sandwich structure: anti-plane case

Due to the incompatibility of the interlaminar deformations,the interface debonding or cracking usually happens in a layered magnetoelectric(ME)structure under an applied load.In this paper,the transient responses of the anti-plane interface cracks in piezoelectric(PE)-piezomagnetic(PM)sandwich structures are studied by the standard methods of the integral transform and singular integral equation.Discussion on the numerical examples indicates that the PE-PM-PE structure under electric impact is more likely to fracture than the PM-PE-PM structure under a magnetic impact.The dynamic stress intensity factors(DSIFs)are more sensitive to the variation of the active layer thickness.The effects of the material constants on the DSIFs are dependent on the roles played by PE and PM media during the deformation process.

High Velocity Impact Experiment on Ti/CFRP/Ti Sandwich Structure

Aircraft laminated composite components often suffer a variety of high velocity impacts with large quantity of energy,which usually affects aircraft behavior and would incur component damages,even disastrous consequences.Therefore,one investigates the impact resistance of a new type of composite material,Ti/CFRP/Ti sandwich structure,and launches impact tests by using an air gun test system.Then one acquires the critical breakthrough rate of the structure and analyzes the damages.The results show that the main failure mode of the front titanium sheet is shear plugging and brittle fracture of adhesive layer with fiber breakage,while the back titanium sheet is severely ripped.The rear damage is worse than the front one.Compared with traditional CFRP laminates,the critical breakthrough rate of Ti/CFRP/Ti sandwich structure is improved by 69.9% when suffered the impact of a bearing ball with 2mm radius.

Design and Simulation of Single Hull Side Structure Based on Filling Sandwich

Ship collision accidents are catastrophic accidents, and as the main energy-absorbing structure, the anti-collision capacity of the side structure has an important influence on the crashworthiness of the ship. It is necessary to improve the crashworthiness of the ship by increasing energy absorption of the side structure, in such ways as adding a filling sandwich in a single hull. The aim of the present study is to discuss the crashworthiness of the side structure stressed under lateral dynamic loads through simulation with the finite element code MSC/Dytran. The collision force, the damage deformation, the critical collision speed as well as the energy absorption of a side structure improved with a filling sandwich are compared to the standard structure through numerical simulations. The results indicate that a sandwich panel structure is an advanced ship protection structure that can remarkably improve the ability of the side structure to withstand collisions; the effect of the tube-style sandwich panel structure has the best results. The outcome of this study provides a reference for the crashworthiness assessment of side structures and the crashworthiness optimization design of new side structures.

Prediction of Compressive and Shear Moduli of X-cor Sandwich Structures for Aeronautic Engineering

The so-called″X-cor sandwich structure″is a highly promising novel material as an alternative to honeycomb used in aircraft.Although much work has been conducted on the performance of the X-cor sandwich structure,the gap is still hardly bridged between experimental results and theoretical analyses.Therefore,a method has been innovated to establish semi-empirical formula for the prediction of compressive and shear moduli of X-cor sandwich structure composites,by combining theoretical analyses and experimental data.In addition,aprediction software was first developed based on the proposed method,of which the accuracy was verified through confirmatory experiments.This software can offer a direct reference or guide for engineers in structural designing.

Acousto-Diffusive Waves in a Piezoelectric-Semiconductor-Piezoelectric Sandwich Structure

The propagation of acoustic waves in a homogeneous isotropic semiconducting layer sandwiched between two homogeneous transversely isotropic piezoelectric halfspaces has been investigated. The mathematical model of the problem is depicted by a set of partial differential equations of motion, Gauss equation in piezoelectric material and electron diffusion equation in semiconductor along with the boundary conditions to be satisfied at the piezoelectric-semiconductor interfaces. The secular equations describing the symmetric and asymmetric modes of wave propagation have been derived in compact form after obtaining the analytical expressions for various field quantities that govern the wave motion. The complex secular equation has been solved numerically using functional interaction method along with irreducible cardano method. The computer simulated results are obtained with the help of MATLAB software for 6 mm cadmium selenide (CdSe) piezoelectric material and n-type silicon (Si) semiconductor in respect of dispersion curve, attenuation and specific loss factor of energy dissipation for symmetric (sym) and asymmetric (asym) modes of wave propagation. The study may find applications in non-destructive testing, resonators, waveguides etc.

Experiments and Analyses on Heat Transfer Characteristics from a Solid Wall to a Strip-ShapedWick Structure

Centered or striped wick structures have been used to develop ultrathin heat pipes.Differing from traditional heat pipes,the centered or striped wick structures leave noncontact container surfaces with the wick structure.In this study,experiments andnumerical analyseswere conductedtoinvestigate the influenceof thesenoncontact surfaces.In the experiments,a strip-shaped wick structure was placed vertically,the top was sandwiched between wider rods and the bottom was immersed in a working fluid.The rod width was greater than the wick width;thus,noncontact surfaces were left between the rod and the wick structure.The heat was applied from the rod to the wick structure,and the evaporation heat transfer characteristics of the working fluid from the wick structure were evaluated.Water was used as the working fluid.The experiments were conducted by varying the rod and wick widths.The experimental results were obtained when the wick structures were placed separately.In the numerical analyses,the temperature and heat flux distributions in the rod were obtained.From the experimental and numerical results,it was confirmed that the noncontact surfaces caused the heat flux in the rod near both surfaces of the wick structure to concentrate,which increased the evaporation thermal resistance of the wick structure.A reduction in the noncontact surface area by increasing the wick width was found to be effective in decreasing the evaporation thermal resistance and increasing themaximumheat transfer rate of the wick structure.The separation of the wick structure increased the evaporation surface area.However,its effectiveness was limited when the heat transfer rate was small.

Short beam shear properties and failure modes of the wood-based X-type lattice sandwich structure

A wood-based X-type lattice sandwich structure was manufactured by insertion-glue method.The birch was used as core,and Oriented Strand Board was used as panel of the sandwich structure.The short beam shear properties and the failure modes of the wood-based X-type lattice sandwich structure with different core direction(vertical and parallel),unit specification(120 mm×60 mm and 60 mm×60 mm),core size(50 mm and 60 mm),and drilling depth(9 mm and 12 mm)were investigated by a short beam shear test and the establishment of a theoretical model to study the equivalent shear modulus and deflection response of the X-type lattice sandwich structure.Results from the short beam shear test and the theoretical model showed that the failure modes of the wood-based X-type lattice sandwich structure were mainly the wrinkling and crushing of the panels under three-point bending load.The experimental values of deflection response of various type specimens were higher than the theoretical values of them.For the core direction of parallel,the smaller the unit specification is,the shorter the core size is,and the deeper the drilling depth is,the greater the short beam shear properties of the wood-based X-type lattice sandwich structure is.

Ion Transport and Microstructure of Sandwich Cementitious Materials Exposed to Chloride Environment

Ion transport of sandwich cementitious materials（SCM） exposed to chloride environment was investigated by accelerated diffusion method and natural diffusion method. Pore structure and micromorphology of SCM were investigated by MIP and SEM-EDS. In comparison with the monolayer structural high performance concrete（HPC）, conductive charge for 6 hours, chloride diffusion coefficient, and apparent chloride diffusion coeffi cient of SCM were decreased by 30%-40%, two orders of magnitude and 40%-50%, respectively. Pore structure of ultra low ion permeability cementitious materials（ULIPCM） prepared for the facesheet is superior to that of HPC prepared for the core. As for porosity, the most probable pore radius, the content of pores with radius 50 nm and the surface area of pores, the order is ULIPCM

A Mini Review on Testing Methods for Mechanical Properties of Natural Fibre Honeycomb Sandwich Structure and Fractography Analysis

This paper is a review of the past research of mechanical testing methods for natural fibre honeycomb sandwich structure as well as failure modes analysis at a microscopic level by using Scanning Electron Microscope (SEM). As the world is garnering attention towards renewable resources for environmental purposes, studies of natural fibre have been increasing as well as the application of natural fibre throughout various industries such as aerospace, automobiles, and construction sectors. This paper is started with brief information regarding the honeycomb sandwich structure, introduction to natural fibre, its applications as well as the factors affecting the performances of the structure. Next, the mechanical testing methods are listed out as well as the expected outcomes obtained from the respective testing. The mechanical properties are also identified by conducting lab tests according to the ASTM standard for sandwich and core structures. The microstructure of the deformed samples is then examined under Scanning Electron Microscope (SEM) by using different magnifications to study the failure mechanisms of the samples. The images obtained from the SEM test are analyzed by using fractography which will show the failure modes of the samples. This article is based on past research conducted by professional on the related topic.

A Mini Review on Natural Fiber Honeycomb (NFH) Sandwiched Structure Composite: Flexural Perfomance Perspective

Natural Fiber Honeycomb (NFH) sandwiched structure composite is a type of composite that uses natural fiber as the reinforcement material and honeycomb structure in the form of a sandwich panel. The demand for commercial use of natural fiber-based composites is increasing in the past few years in many industrial sectors. The increase in popularity of natural fibers is because of their particular properties, price, health benefits, and recyclability. This paper aims to analyze the data and analysis of the past research about NFH sandwiched structure composite in terms of the materials used to make the NFH, the physical and mechanical properties, and their applications. Based on the literature review conducted, there were many types of materials used to make the NFH sandwiched structure composite. Some experimental tests were planned and conducted to analyze the mechanical properties of the NFH and its potential to be used in the desired industries. However, there are not many implementations of NFH composite in the construction industry. This is due to the concern related to the issue of the structural integrity of the NFH composite. From the literature review conducted, most of the research shows a positive analysis of the mechanical properties and the potential of the developed NFH to be used for the targeted industry in the study. Therefore, it can be observed that the material used in this study has a high potential to be used in the construction industry.

Discussion on "sandwich"structures and preservation conditions of shale gas in the South Yellow Sea Basin

In order to make a breakthrough in Mesozoic-Paleozoic shale gas exploration in the South Yellow Sea Basin,a comparison of the preservation conditions was made within the Barnett shale gas reservoirs in the Fortworth Basin,the Jiaoshiba shale gas reservoirs in Sichuan Basin and potential shale gas reservoirs in Guizhou Province.The results show that the "Sandwich"structure is of great importance for shale gas accumulation.Therein to,the "Sandwich"structure is a kind of special reservoir-cap rock assemblage which consist of limestone or dolomite on the top,mudstone or shale layer in the middle and limestone or dolomite at the bottom.In consideration of the Mesozoic-Paleozoie in the Lower Yangtze,and Laoshan Uplift with weak Paleozoic deformation and thrust fault sealing On both flanks of the Laoshan Uplift,a conclusion can be drawn that the preservation conditions of shale gas probably developed "Sandwich" structures in the Lower Cambrian and Permian,which are key layers for the breakthrough of shale gas in the South Yellow Sea.Moreover,the preferred targets for shale gas drilling probably locate at both flanks of the Laoshan Uplift.

Development of Composite Cellular Cores for Sandwich Panels Based on Folded Polar Quadra-Structures

An idea to develop a family of cellular cores for sandwich panels using a technology of prepreg folding is presented. Polar folded quadra structures are regarded as a geometric basis for these cores whose standard frag ment has lhe fourlh degree of axial symmelry. The classification of the polar strucluresaredeseribedanda method of various quadra slrueture synthesis is developed. A possibilily to provide high strength of lhe structure due m preservation of faces reinforcement pattern is presented. Arrangemen! of the plane core on a bi curvature surface is also introduced. Besides, provision of isotropyof the core in two or three directions are described. Finally, exam ples of cellular folded cores manufaclured from basalt reinforced plaslic are demonslrated.

Multi-objective optimization design of radar absorbing sandwich structure

By introducing a dimensionless parameter to couple the two objectives, weight and radar absorbing performance, into a single objective function, a multi-objective optimization procedure for the radar absorbing sandwich structure （RASS） with a cellular core is proposed. The optimization models considered are one-side clamped sandwich panels with four kinds of cores subject to uniformly distributed loads. The average specular reflectivity calculated with the transfer matrix method and the periodic moment method is utilized to characterize the radar absorbing performance, while the mechanical constraints include the facesheet yielding, core shearing, and facesheet wrinkling. The optimization analysis indicates that the sandwich structure with a two-dimensional （2D） composite lattice core filled with ultra-lightweight sponge may be a better candidate of lightweight RASS than those with cellular foam or hexagonal honeycomb cores. The 2D Kagome lattice is found to outperform the square lattice with respect to radar absorbing.

Synthesis and Crystal Structure of an Infinite Sandwich-type Cu(I) Coordination Polymer: {[Cu(abpy)_2](H_3bptc)·(H_2O)}_n Constructed by a Tetracarboxylic Acid

The title compound {[Cu（abpy）2]（H3bptc）·（H2O）}n, an ion-pair complex of [Cu（abpy）2]＋ with [（H3bptc）]- （abpy = 3,3＇-dimethyl-2,2＇-bipyridine and H4bptc = 1,1＇-biphenyl-2,2＇,3,3＇-tetracarboxylic acid）, has been synthesized by a hydrothermal reaction, and its structure was deter- mined by X-ray diffraction and characterized by elemental analysis and IR spectrum. The crystal is of triclinic, space group P1 with a = 8.4955（12）, b = 15.164（2）, c = 15.303（2）, α = 105.704（3）, β = 97.374（3）, γ = 96.764（3）o, CuC40H35N4O9, Mr = 779.26, V = 1857.9（4）3, Dc = 1.393 g/cm3, F（000） = 808, μ = 0.649 mm-1, S = 1.026 and Z = 2. The final R = 0.0493 and wR = 0.1034 for 4026 observed reflections with I 2σ（I）. The copper（I） coordination polymer demonstrates a 3-D sandwich-type structure containing 2-D double H3bptc-chain layers intercalated with the [Cu（abpy）2]＋ layers by extensive hydrogen bonding interactions.

An Optimum Analysis Method of Sandwich Structures Made from Elastic-viscoelastic Materials

Due to a viscoelastic damping middle layer,sandwich structures have the capacity of energy consumption.In this paper,we describe the frequency-dependent property of viscoelastic materials using complex modulus model,and iterative modal strain energy method and iterative complex eigenvalue method are presented to obtain frequency and loss factor of sandwich structures.The two methods are effective and exact for the large-scale complex composite sandwich structures.Then an optimum analysis method is suggested to apply to sandwich structures.Finally,as an example,an optimum analysis of a clamped-clamped sandwich beams is conducted,theoretical closed-form solution and numerical predictions are studied comparatively,and the results agree well.

Superplastic Forming and Diffusion Bonding for Sandwich Structure of Ti-6Al-4V Alloy

Superplastic forming and diffusion bonding (SPF/DB) is a well-established process for the manufacture of components almost exclusively from Ti-6AI-4V sheet material. The sandwich structure of Ti-6AI-4V alloy is investigated. The effects of the microstructure on the SPF/DB process were discussed. The microstructure at the interfaces and the distribution of thickness were researched.