Greatly enhanced corrosion/wear resistances of epoxy coating for Mg alloy through a synergistic effect between functionalized graphene and insulated blocking layer

The poor corrosion and wear resistances of Mg alloys seriously limit their potential applications in various industries.The conventional epoxy coating easily forms many intrinsic defects during the solidification process,which cannot provide sufficient protection.In the current study,we design a double-layer epoxy composite coating on Mg alloy with enhanced anti-corrosion/wear properties,via the spin-assisted assembly technique.The outer layer is functionalized graphene(FG)in waterborne epoxy resin(WEP)and the inner layer is Ce-based conversion(Ce)film.The FG sheets can be homogeneously dispersed within the epoxy matrix to fill the intrinsic defects and improve the barrier capability.The Ce film connects the outer layer with the substrate,showing the transition effect.The corrosion rate of Ce/WEP/FG composite coating is 2131 times lower than that of bare Mg alloy,and the wear rate is decreased by~90%.The improved corrosion resistance is attributed to the labyrinth effect(hindering the penetration of corrosive medium)and the obstruction of galvanic coupling behavior.The synergistic effect derived from the FG sheet and blocking layer exhibits great potential in realizing the improvement of multi-functional integration,which will open up a new avenue for the development of novel composite protection coatings of Mg alloys.

Large energy-loss straggling of swift heavy ions in ultra-thin active silicon layers

Monte Carlo simulations reveal considerable straggling of energy loss by the same ions with the same energy in fully-depleted silicon-on-insulator （FDSOI） devices with ultra-thin sensitive silicon layers down to 2.5 rim. The absolute straggling of deposited energy decreases with decreasing thickness of the active silicon layer. While the relative straggling increases gradually with decreasing thickness of silicon films and exhibits a sharp rise as the thickness of the silicon film descends below a threshold value of 50 nm, with the dispersion of deposited energy ascending above ~10%. Ion species and energy dependence of the energy-loss straggling are also investigated. For a given beam, the dispersion of deposited energy results in large uncertainty on the actual linear energy transfer （LET） of incident ions, and thus single event effect （SEE） responses, which pose great challenges for traditional error rate prediction methods.

Plasma Surface Cu Alloyed Layer as a Lubricant on Stainless Steel Sheet:Wear Characteristics and On-job Performance in Incremental Forming

To solve the problems of poor forming and easy adhesion of the stainless steel,Cu alloyed layer on the stainless steels was prepared by the double glow plasma surface alloying technique.The experimentalresults indicated that the supersaturated copper dispersedly precipitated in grain interior and crystalboundaries and formed the vermicular structure.The tribologicaltests indicated that the friction coefficient of the Cu alloyed layer was lower than that of the stainless steels.The wear rate of stainless steelin the presence of Cu alloyed layer was approximately 2-fold lower than that in the absence of the alloyed layer.The results of the incrementalforming indicated that the ploughing phenomenon was not observed on the stainless steelin the presence of Cu alloyed layer during the incrementalforming,while the stainless steelpresented the deep ploughing.Therefore,Cu alloyed layer on stainless steelexhibited excellent self-lubrication and forming properties.

Microstructure and abrasion wear behavior of Ni-based laser cladding alloy layer at high temperature

Ni-based alloy coating on 21-4-N heat-resistant steel was prepared using CO2 laser, and the high-temperature abrasion wear was tested. The microstructure of this cladding layer and its abrasion wear behavior at high temperature by changing compositions and temperatures were investigated by means of optical microscope and scanning electron microscope. Among the three compositions of cladding layer, i.e. Ni21+20%WC+0.5%CeO2, Ni25+20%WC+0.5%CeO2 and Ni60+20%WC+0.5%CeO2, the experimental results show that Ni21+20%WC+ 0.5%CeO2 cladding layer is made up of finer grains, and presents the best abrasion wear behavior at high temperature. The wear pattern of laser cladding layer is mainly grain abrasion at lower temperature, and it would be changed to adhesive abrasion and oxide abrasion at higher temperature.

Wear Performance of Ni/ZrO_2 Infiltrated Composite Layer

The Ni/ZrO2 was used as raw materials to fabricate the surface infiltrated composite layer with 1-4 mm thickness on cast steel substrate through vacuum infiltrated casting technology. The microstructure indicated that the infiltrated composite layer included surface composite layer and transition layer. Wear property was investigated under room temperature and 450 ~C. The results indicated that the abrasion volume of substrate was 8 times that of the infiltrated composite layer at room temperature. The friction coefficient of infiltrated composite layer decreased with the increasing load. The wear resistance of infiltrated composite layer with different ZrO2 contents had been improved obviously under high temperature. The friction coefficient of infiltrated composite layer was decreased comparing with that at room temperature. The oxidation, abrasive and fatigue abrasion was the main wear mechanism at room temperature. Oxidation abrasion, fatigue wear and adhesive wear dominated the wearin~ process under elevated temperature.

Optical properties of ultra-thin InN layer embedded in InGaN matrix for light emitters

We theoretically investigate the optical properties of an ultra-thin InN layer embedded in InGaN matrix for light emitters. The peak emission wavelength extends from ultraviolet （374 nm） to green （536 nm） with InN quantum well thickness increasing from 1 monolayer to 2 monolayers, while the overlap of electron–hole wave function remains at a high level （larger than 90%）. Increase of In content in InGaN matrix provides a better approach to longer wavelength emission, which only reduces the spontaneous emission rate slightly compared with the case of increasing In content of the conventional InGaN quantum well. Also, the transparency carrier density derived from gain spectrum is of the same order as that in the conventional blue laser diode. Our study provides skillful design on the development of novel structure InN-based light emitting diodes as well as laser diodes.

Study on characteristics of a double-conductible channel organic thin-film transistor with an ultra-thin hole-blocking layer

The properties of top-contact organic thin-film transistors （TC-OTFTs） using ultra-thin 2, 9-dimethyl-4, 7- diphenyl-1, 10-phenanthroline （BCP） as a hole-blocking interlayer have been improved significantly and a BCP interlayer was inserted into the middle of the pentacene active layer. This paper obtains a fire-new transport mode of an OTFT device with double-conductible channels. The accumulation and transfer of the hole carriers arc limited by the BCP interlayer in the vertical region of the channel. A huge amount of carriers is located not only at the interface between pentacene and the gate insulator, but also at the two interfaces of pentacene/BCP interlayer and pentacene/gate insulator, respectively. The results suggest that the BCP interlayer may be useful to adjust the hole accumulation and transfer, and can increase the hole mobility and output current of OTFTs. The TC-OTFTs with a BCP interlayer at VDS = --20 V showed excellent hole mobility μFE and threshold voltage VTH of 0.58 cm^2/（V-s） and -4.6 V, respectively.

On the viability of wearing evaluation by Thin Layer Activation in the presence of non-occupationally exposed individuals

Thin Layer Activation is a nuclear technique that has key advantages over other wear measuring techniques for mechanical systems,especially for in site experiments on equipment important to safety in nuclear plants.Still,it incurs radioactive dose and,thus,must be proved radiologically safe before use,otherwise,the utilization of this technique may be hindered inviable.Proving said technique is safe previous to any operational/monetary cost is key,providing a methodology for this early assertion is the main contribution of this work—here,only non-occupationally exposed individuals are considered.This work offers a methodology,through a case study,to ascertain the Thin Layer Activation parameters to obtain safe levels of radioactive dose while maintaining statistically reliable results.This methodology consists of using simulations,through the Monte Carlo Method,to obtain the floors and ceilings for the previously mentioned activation parameters based on operation and work conditions on site.

MICROSTRUCTURE AND MECHANISM OF A NEW TYPE OF Ni－Fe－W－P－S WEAR－RESISTANT BRUSH PLATING LAYER

ＭＩＣＲＯＳＴＲＵＣＴＵＲＥＡＮＤＭＥＣＨＡＮＩＳＭＯＦＡＮＥＷＴＹＰＥＯＦＮｉ－Ｆｅ－Ｗ－Ｐ－ＳＷＥＡＲ－ＲＥＳＩＳＴＡＮＴＢＲＵＳＨＰＬＡＴＩＮＧＬＡＹＥＲＨｕｉＷｅｎｈｕａ（惠文华）ＺｈａｎｇＪｉｎｐｉｎｇ（张瑾平）ＳｈａｏＬｉｗｅｉ（邵力为）...

Effect of Micro-addition Rare Earth and Chrome on Friction and Wear Behavior of Boronized layer

Application of powder boronizing to mechanical industry has been restricted because of the brittleness of boronized layer, which inevitably leads to decrease of service life of boronized parts. Therefore, attention should be paid to reducing the brittleness of boronized layer without decreasing its high hardness. In the present paper, a study on the effect of micro-addition rare earth and chrome on friction and wear behavior of boronized layer was carried out using an MM-200 wear test machine. Compared with that of pure single Fe2B phase, the brittleness of the boronized layer containing minim rare earth and chrome elements, obtained by powder RE-chrome-boronizing, is reduced, which results in increasing the bearing capacity and wear resistance of the boronized layer. The friction and wear mechanism is also briefly analyzed.

Interface characteristics and wear resistance of Ni-B_(4)C plated ZTA reinforced high chromium cast iron composite

A chemical composite plating of Ni-B_(4)C was used to prepare the surface-modified zirconia toughened alumina(ZTA)ceramic particles.The ceramic preforms were prepared by the plated ZTA and sodium silicate solution binder,followed by casting infiltration to prepare the ZTA particles reinforced high chromium cast iron(HCCI)composites.The result reveals that a distinct interface layer forms at the ZTA/HCCI interface,which consists of phases of ZrB_(2),FeB,Fe_(2)B,and NaSiO_(4).The interfacial wettability between ZTA and HCCI is improved by the diffusion and reaction of Ni and B_(4)C.The wear test reveals that the Ni-B_(4)C plated ZTA particles can effectively improve the wear resistance of the ZTA/HCCI composite,and the wear rate of the composite is decreased to 11.6%of HCCI.

Cartilage Wear in Healthy and Osteoarthritis Joints

This study is designed to determine whether the outermost layer of articular cartilage is deficient in Osteoarthritis (OA). Phospholipids present in healthy and osteoarthritis (OA) synovial fluid show significant differences in their concentration. While examining the surface properties of OA joints, we found that OA PLs molecules cannot support lubrication, and increased friction was observed. Our lubrication mechanism was based on a surface active phospholipids (SAPL) multibilayer which in OA condition was deactivated and removed from the cartilage surface under OA conditions. Cartilage wettability study clearly demonstrated a significant decrease in hydrophobicity, the contact angle, θ (theta), dropping from 103° from bovine healthy cartilage to 65° in surface partially depleted and 35.1° for completely depleted surface. These results are discussed in the context that surface active phospholipid (SAPL) and lubricin, each has specific roles in a lamellar-repulsive lubrication system. However, deactivated phospholipid molecules are major indicator of cartilage wear (model) introduced in this study.

Improving wear resistance of magnesium alloy AZ91D by TiN-CrN multilayer coating

Applying a novel method of arc-glow plasma depositing, a 2μm-thick coating with 12 sub-layers of TiN and CrN was deposited alternately on the surface of magnesium alloy AZ91D to improve its wear resistance. The wear behavior was investigated by test of ball on disc sliding. The composition and microstructure of the coating were also analyzed by means of X-ray diffraction (XRD) and glow discharge spectrum (GDS), and the morphology of TiN-CrN film was surveyed through scanning electronic microscopy (SEM) and atom force microscopy (AFM).The adhesion strength between film and matrix was evaluated by ways of stick-peeling test. The surface micro-hardness of the coating is above HK0.011 433, and the specific wear ratio of specimens coated with TiN-CrN films tested decreases greatly compared to that of the bare metal.

超薄磨耗层抗滑性能的衰变规律及其影响因素

为了精确评价沥青超薄磨耗层开放交通后抗滑性能衰变过程、机理及影响因素,首先利用弧形模具及其配套的轮碾机来制备弧形超薄磨耗层试件;然后通过驱动轮式加速加载系统对4种级配类型和3个沥青胶结料等级的沥青超薄磨耗层试件进行加速加载试验;最后借助激光纹理扫描仪对一定轮载次数作用后的试件分别进行扫描。结合试验数据分别建立了基于S型函数的沥青超薄磨耗层宏观和微观构造深度衰变模型,以及基于灰色关联分析方法来分析各空隙率和沥青胶结料对抗滑性能的独立和耦合作用。试验研究结果显示:采用驱动轮式加速加载系统结合S型函数模型可以定量地评价和预测沥青超薄磨耗层性能的演变过程;空隙率影响超薄磨耗层宏观和微观构造深度的前期衰减速率,空隙率越大,则超薄磨耗层的宏观和微观构造深度的前期衰减速率越大;宏观构造深度的中后期衰减速率受沥青胶结料等级影响更大,沥青胶结料性能等级越高,则宏观构造深度的中后期衰减速率越慢;空隙率和沥青胶结料等级对超薄磨耗层微观构造深度中后期衰减速率的影响相当。因此,在进行超薄磨耗层抗滑性能设计时,选择大空隙率的开级配超薄磨耗层混合料级配对路面抗滑耐久性是有益的,而沥青胶结料的性能等级则可以根据交通量的大小合理选择。

多物理场下超薄吸波磨耗层微波加热性能研究

微波加热技术在沥青路面除冰中的应用得到了广泛的关注,然而目前多对沥青路面整体进行微波加热增强,从而导致路表加热效率提升缓慢。为了进一步提高沥青路面路表的微波加热性能,采用碳化硅(SiC)微波增强集料制备了一种超薄吸波磨耗层,通过微波加热以及除冰试验分析了超薄吸波磨耗层的微波加热性能以及加热耐久性,确定了超薄吸波磨耗层的最佳厚度。并采用COMSOL Multiphysics有限元软件建立了多物理场沥青混凝土微波加热模型,分析了超薄吸波磨耗层的设置对微波加热过程中电磁场的强度与分布以及温度场的影响。研究结果表明:在2.45 GHz频率的微波加热下,超薄吸波磨耗层具有良好的微波加热性能,10 mm厚的超薄吸波磨耗层的微波加热效率相比于普通沥青混合料以及整体微波增强的沥青混合料提高了4.47倍和1.40倍。SiC稳定的微波吸收性能保证了超薄吸波磨耗层具有良好的微波除冰耐久性,在经过反复的微波加热除冰后超薄吸波磨耗层的除冰时间仍然可以保持在45 s左右。数值仿真模拟结果表明超薄吸波磨耗层较强的微波吸收能力可以局部增强试件表层的电磁场强度,从而使更高的温度分布在试件表层。超薄吸波磨耗层内部的电场强度和磁场强度分别比普通沥青混合料试件提高了50.9%和15.7%。综上可知,超薄吸波磨耗层的设置可以提高沥青路面表面的微波加热性能。

枪管用环保镀层摩擦行为研究

传统枪管内膛表面采用的六价铬镀层,高温耐磨性好,但对环境污染严重。为开发环保镀层,采用超景深三维显微镜、扫描电子显微镜表征了室温和高温(400℃)摩擦磨损试样,对比分析了六价铬、三价铬、钴-镍和镍-钨四种电镀层的磨损特征。研究结果表明:在500℃定性回火后,三价铬、镍-钨、六价铬和钴-镍镀层硬度依次递减,与六价铬层相比,三价铬层脆性大,镍-钨和钴-镍镀层韧性高;室温下与H62黄铜对摩后,六价铬和三价铬镀层摩擦程度较轻,钴-镍和镍-钨镀层呈现明显粘着特征,二者摩擦系数高于两种铬层;400℃下与08Al钢对摩后,六价铬呈粘着磨损特征,摩擦程度较大;三价铬层摩擦系数相对较高;镍-钨镀层呈磨粒磨损特征,摩擦系数与六价铬接近,摩擦程度相对较轻。

Cr_(3)C_(2)/WC的添加对Stellite 12熔覆层耐磨耐蚀性的影响

目的 提高Stellite 12熔覆层的耐磨耐蚀性能。方法将Stellite 12合金粉末与碳化物(Cr_(3)C_(2)、WC)混合,采用激光熔覆技术在H13钢板上制备复合熔覆层。通过超景深显微镜和XRD分析其显微组织和物相,通过显微硬度测试、摩擦磨损试验和电化学腐蚀试验,分别评价熔覆层的硬度、耐磨性和耐蚀性,并通过超景深显微镜对磨痕形貌进行分析。结果添加碳化物后,熔覆层的微观组织以柱状晶和树枝晶为主,物相主要由γ-Co固溶体和碳化物(M23C6、M7C3)组成;Cr_(3)C_(2)的添加使得熔覆层的硬度降低,由610HV0.2降至530HV0.2,但耐磨性得到提高,磨损量由0.45 mm^(3)降至0.33 mm^(3),下降了28%,耐蚀性得到提高,腐蚀电位由-0.385 V增加到-0.264 V,腐蚀电流密度由9.269×10^(-10)A/cm^(2)降至1.496×10^(-10)A/cm^(2),极化电阻由3.982×10^(7)Ω·cm^(2)提升至2.424×10^(8)Ω·cm^(2),提高了1个数量级;WC的添加使其硬度由610HV0.2提高至750HV0.2,磨损深度变浅,磨损量由0.45 mm3降至0.19 mm^(3),下降了43%,但耐腐蚀性有所降低。3种熔覆层的磨损机制主要为磨粒磨损和黏着磨损。结论WC的添加可以有效提高熔覆层的硬度和耐磨性,但耐腐蚀性有所降低;添加Cr_(3)C_(2)后,耐蚀性得到显著提高,耐磨性略微提升,但硬度降低。

激光熔凝处理对P20钢组织及性能的影响

目的提高P20模具钢的表面硬度和耐磨性能。方法采用激光熔凝技术对P20模具钢表面进行强化处理。通过硬度梯度检测和摩擦磨损测试,分别评价熔凝层的硬度分布特征和耐磨性能,并通过光学显微镜和扫描电子显微镜对熔凝层及磨痕形貌进行分析。结果使用激光输出功率为500W、光斑直径为2.5mm、聚焦透镜距离为40 mm、扫描速度为6 mm/s、搭接率为45%、氮气保护的激光熔凝工艺所得熔凝层的组织细小,无脱碳、畸变、裂纹等缺陷,熔凝处理质量高。熔凝过程中单道激光熔凝层呈半椭圆形分布,最大深度为610~620μm。熔凝处理后表面硬度提升显著,熔凝层的硬度分布与熔凝层的区域位置有关,具有较高硬度且硬度保持基本稳定的熔凝层深度约为400μm;单道激光熔凝层最高硬度可达460~480HV,重叠影响区即双熔凝区的最高硬度在540~560HV之间,即熔凝层硬度普遍较基体硬度提高了60%以上。此外,P20模具钢经过激光熔凝处理后耐磨性能提升明显,其平均摩擦因数约为0.85,熔凝处理的磨损失重较未处理的试样减少了约61%,其磨损机制主要表现为磨粒磨损和少量的黏着磨损或剥落脱离。结论激光熔凝处理能够显著提高P20模具钢的表面硬度和耐磨性能,试验采用的激光熔凝工艺可在P20钢表面获得硬度较高且稳定可靠的熔凝层深度在400μm左右,能将P20模具钢的表面硬度及耐磨性提高60%以上。

钛合金摩擦磨损性能及减磨方法研究进展

钛合金具有比强度高、抗腐蚀性强、耐高温以及生物相容性好等优点,在汽车制造、生物医疗等众多领域具有重要应用。但钛合金的摩擦磨损性能较差,会影响机械系统的使用寿命和可靠性。首先论述了摩擦磨损过程中摩擦层的形成过程以及摩擦层对钛合金磨损机理的作用,分析了润滑条件、环境温度、滑动速度、载荷等工况条件对钛合金摩擦磨损性能的影响规律。其次,对比总结了钛合金减磨的常见工艺方法及优缺点,指出了当前钛合金磨损机理研究和性能改善方面存在的问题。最后,对今后的研究工作进行了展望:将实验与仿真相结合,阐明钛合金摩擦层和磨损机理的动态变化规律;考虑各种环境因素对钛合金磨损机理的影响,完善钛合金磨损机制图;通过对多种技术协同配合时的工艺参数进行优化,促进钛合金表面强化复合技术的发展,从而提升钛合金的耐磨减摩性能。

热拌极薄抗滑磨耗层在高速公路抗滑性能提升中的应用

为研究热拌极薄抗滑磨耗层在高速公路养护中的应用,提升路面抗滑性能,论文结合实际工程,介绍了热拌极薄抗滑磨耗层工程特性,详细阐述了热拌极薄抗滑磨耗层原材料及配合比设计,重点对热拌极薄抗滑磨耗层施工技术要点进行研究。结果表明:公路养护中采取热拌极薄磨耗层技术进行处理,其路面抗滑性能得到有效提高,并节约养护成本。