Comparative Study on Microstructure and Mechanical Properties of Coarse-grained WC-based Cemented Carbides Sintered with Ultrafine WC or (W+C) as Additives

The effects of ultrafine WC(WC_(UF),0.5μm) or W(1μm) and C(0.3μm)(W+C)_(UF) additives on the densification,microstructure and mechanical properties of coarse-grained cemented carbides were compared systematically.Overall,the cemented carbides with WC_(UF)/(W+C)_(UF) additives are almost fully densification to be higher than 99%,and the average grain size is kept above 2.8μm.The WC_(UF) additive assists grains to(truncated)trigonal prism shape by two dimensional(2D) growth,whereas the(W+C)_(UF) additive assists grains to rounded shape by three dimensional(3D) growth,lowers WC contiguity and increases face-centered-cubic Co.The hardness and bending strength of(75WC_(C)-15WC_(UF))-10Co are 86.6 HRA and 2 272 MPa,respectively,both higher than those of(75WC_(C)-15(W+C)_(UF))-10Co,which could be ascribed to the enhanced densification and unblemished grains.However,the fracture toughness of the(75WC_(C)-15(W+C)_(UF))-10Co is 23.5 MPa·m^(1/2),higher than that of the(75WC_(C)-15WC_(UF))-10Co due to the uniform WC-Co structure and flexible binder phase.

Development and application of novel high‐efficiency composite ultrafine cement grouts for roadway in fractured surrounding rocks

The fractured surrounding rocks of roadways pose major challenges to safe mining.Grouting has often been used to reinforce the surrounding rocks to mitigate the safety risks associated with fractured rocks.The aim of this study is to develop highly efficient composite ultrafine cement(CUC)grouts to reinforce the roadway in fractured surrounding rocks.The materials used are ultrafine cement(UC),ultrafine fly ash(UF),ultrafine slag(US),and additives(superplasticizer[SUP],aluminate ultrafine expansion agent[AUA],gypsum,and retarder).The fluidity,bleeding,shrinkage,setting time,chemical composition,microstructure,degree of hydration,and mechanical property of grouting materials were evaluated in this study.Also,a suitable and effective CUC grout mixture was used to reinforce the roadway in the fractured surrounding rock.The results have shown that the addition of UF and US reduces the plastic viscosity of CUC,and the best fluidity can be obtained by adding 40%UF and 10%US.Since UC and UF particles are small,the pozzolanic effect of UF promotes the hydration reaction,which is conductive to the stability of CUC grouts.In addition,fine particles of UC,UF,and US can effectively fill the pores,while the volumetric expansion of AUA and gypsum decreases the pores and thus affects the microstructure of the solidified grout.The compressive test results have shown that the addition of specific amounts of UF and US can ameliorate the mechanical properties of CUC grouts.Finally,the CUC22‐8 grout was used to reinforce the No.20322 belt roadway.The results of numerical simulation and field monitoring have indicated that grouting can efficaciously reinforce the surrounding rock of the roadway.In this research,high‐performance CUC grouts were developed for surrounding rock reinforcement of underground engineering by utilizing UC and some additives.

New insights in nano-copper chromite catalyzing ultrafine AP:Evaluation of dispersity and mixing uniformity

Improving the application of nanomaterials has always been a research hotspot in the field of energetic materials(EMs)due to their obvious catalytic effect on the EMs,especially the uniformly dispersed nanomaterials.However,few studies have reported the dispersion of nanomaterials.In this study,the dispersity and mixing uniformity of nano-CuCr_(2)O_(4)was evaluated based on the difference of solid UV light absorption between the nano-catalytic materials and EMs.The nano-CuCr_(2)O_(4)/ultrafine AP composites with different dispersity of nano-CuCr_(2)O_(4)were prepared by manual grinding and mechanical grinding with different grinding strength and griding time.And then,the absorbance of different samples at 212 nm was obtained by solid UV testing due to the high repeatability of the absorbance at 210-214 nm for three parallel experiments,and the dispersity of different samples was calculated through the established difference equation.Furthermore,the samples were characterized by XRD,IR,SEM,EDS,DSC and TG-MS,which confirmed that different mixing methods did not change the structure of the samples(XRD and IR),and the mixing uniformity improved with the increase of grinding strength and grinding time(SEM and EDS).The scientificity and feasibility of the difference equation were further verified by DSC.The dispersity of nano-CuCr_(2)O_(4)exhibits a positive intrinsic relationship with its catalytic performance,and the uniformly dispersed nano-CuCr_(2)O_(4)significantly reduces the thermal decomposition temperature of ultrafine AP from 367.7 to 338.8℃.The TG-MS patterns show that the dispersed nano-CuCr_(2)O_(4)advanced the thermal decomposition process of ultrafine AP by about 700 s,especially in the high temperature decomposition stage,and the more concentrated energy release characteristic is beneficial to further enhance the energy performance of AP-based propellants.The above conclusions show that the evaluation method of dispersity based on solid UV curves could provide new ideas for the dispersity characterization of nano-catalytic materials in EMs,which is expected to be widely used in the field of EMs.

Microfluidic preparation of surfactant-free ultrafine DAAF with tunable particle size for insensitive initiator explosives

High purity and ultrafine DAAF(u-DAAF)is an emerging insensitive charge in initiators.Although there are many ways to obtain u-DAAF,developing a preparation method with stable operation,accurate control,good quality consistency,equipment miniaturization,and minimum manpower is an inevitable requirement to adapt to the current social technology development trend.Here reported is the microfluidic preparation of u-DAAF with tunable particle size by a passive swirling microreactor.Under the guidance of recrystallization growth kinetics and mixing behavior of fluids in the swirling microreactor,the key parameters(liquid flow rate,explosive concentration and crystallization temperature)were screened and optimized through screening experiments.Under the condition that no surfactant is added and only experimental parameters are controlled,the particle size of recrystallized DAAF can be adjusted from 98 nm to 785 nm,and the corresponding specific surface area is 8.45 m^(2)·g^(-1)to 1.33 m^(2)·g^(-1).In addition,the preparation method has good batch stability,high yield(90.8%-92.6%)and high purity(99.0%-99.4%),indicating a high practical application potential.Electric explosion derived flyer initiation tests demonstrate that the u-DAAF shows an initiation sensitivity much lower than that of the raw DAAF,and comparable to that of the refined DAAF by conventional spraying crystallization method.This study provides an efficient method to fabricate u-DAAF with narrow particle size distribution and high reproducibility as well as a theoretical reference for fabrication of other ultrafine explosives.

Enabling High-Performance Sodium Battery Anodes by Complete Reduction of Graphene Oxide and Cooperative In-Situ Crystallization of Ultrafine SnO_(2)Nanocrystals

The main bottleneck against industrial utilization of sodium ion batteries(SIBs)is the lack of high-capacity electrodes to rival those of the benchmark lithium ion batteries(LIBs).Here in this work,we have developed an economical method for in situ fabrication of nanocomposites made of crystalline few-layer graphene sheets loaded with ultrafine SnO_(2)nanocrystals,using short exposure of microwave to xerogel of graphene oxide(GO)and tin tetrachloride containing minute catalyzing dispersoids of chemically reduced GO(RGO).The resultant nanocomposites(SnO_(2)@MWG)enabled significantly quickened redox processes as SIB anode,which led to remarkable full anode-specific capacity reaching 538 mAh g^(−1)at 0.05 A g^(−1)(about 1.45 times of the theoretical capacity of graphite for the LIB),in addition to outstanding rate performance over prolonged charge–discharge cycling.Anodes based on the optimized SnO_(2)@MWG delivered stable performance over 2000 cycles even at a high current density of 5 A g^(−1),and capacity retention of over 70.4%was maintained at a high areal loading of 3.4 mg cm^(−2),highly desirable for high energy density SIBs to rival the current benchmark LIBs.

Polypyrrole-Coated Zein/Epoxy Ultrafine Fiber Mats for Electromagnetic Interference Shielding

To reduce the environmental pollution and meet the needs for wearable electronic devices, new requirements for electromagnetic interference(EMI) shielding materials include flexibility, biodegradability, and biocompatibility. Herein, we reported a polypyrrole-coated zein/epoxy(PPy/ZE) ultrafine fiber mat which was inherently biodegradable and skin-friendly. In addition, it could maintain its ultrafine fibrous structure after coating, which could provide the mat with mechanical compliance, high porosity, and a large specific area for high EMI shielding. With the assistance of the epoxide cross-linking, the breaking stresses of the PPy/ZE fiber mats could achieve 3.3 MPa and 1.4 MPa and the strains were 40.1% and 83.0% in dry and wet states, respectively, which met the needs of various wearable electronic devices. Along with the extension in the PPy treatment duration, more PPy was loaded on the fiber surfaces, which formed more integrated and conductive paths to generate increasing conductivities up to 401.76 S·m^(-1). Moreover, the EMI shielding performance was raised to 26.84 dB. The biobased mats provide a green and efficient choice for EMI shielding materials, which may be a promising strategy to address EMI problems in multiple fields.

MoS_(2) nanoflowers coupled with ultrafine Ir nanoparticles for efficient acid overall water splitting reaction

Bi-functional electrocatalysts for acid overall water splitting reactions are crucial but still challenging to the development of proton exchange membrane water electrolysis.Herein,an efficient bi-functional catalyst of Ir/MoS_(2) nanoflowers(Ir/MoS_(2) NFs) catalyst was reported for acidic water electrolysis which can be constructed by coupling three-dimensionally interconnected MoS_(2) NFs with ultrafine Ir nanoparticles.A more suitable adsorption ability for the H* and *OOH intermediates was revealed,where the Ir sites were proposed as the main active center and MoS_(2) promoted the charge relocation to electronically modify the interfacial structure.The significant interfacial charge redistribution between the MoS_(2) NFs and the Ir active sites synergistically induced excellent catalytic activity and stability for the water electrolysis reaction.Specifically,the catalyst required overpotentials of 270 and 35 mV to reach a kinetic current density of 10 mA cm^(-2)for OER and HER,respectively,loading on the glass carbon electrode,with high catalytic kinetics,stability,and catalytic efficiency.A two-electrode system constructed by Ir/MoS_(2) NFs drove 10 mA cm^(-2)at a cell voltage of 1.55 V,about 70 mV lower than that of the commercial Pt/C||IrO_(2) system.In addition,partial surface oxidation of Ir nanoparticles to generate high-valent Ir species was also found significant to accelerate OER.The enhanced catalytic performance was attributed to the strong metal-support interaction in the Ir/MoS_(2) NFs catalyst system that changed the electronic structure of Ir metal and promoted the synergistic catalytic effect between Ir and MoS_(2) NFs.The work presented a novel platform of Ir-catalyst for proton exchange membrane water electrolysis.

Shear hydrophobic flocculation and flotation of ultrafine Anshan hematite using sodium oleate

Effects of stirring speed and time, pH and sodium oleate concentration on the shear hydrophobic flocculation of ultrafine Anshan hematite with sodium oleate as the surfactant were discussed. The results show that these parameters significantly affect the shear hydrophobic flocculation of ultrafine hematite. The optimum conditions for the flocculation are： stirring speed 1 400 r/min, flocculation time 20 min, pH 9 and sodium oleate concentration 3.94×10-4 mol/L; the flotation recovery of hematite flocs is remarkably high compared with non flocculated ultrafine hematite. According to the extended DLVO theory, the total interaction potential of Anshan ultrafine hematite was determined. The calculation results indicate that the hydrophobic flocculation state of the ultrafine hematite-sodium oleate system is mainly dominated by electric double layer repulsive interaction potential and hydrophobic interaction potential. A mechanical agitation is required to impart particles a kinetic energy to overcome potential barrier between them due to the existence of electric double layer repulsive interaction potential. Those particles further approach to form flocs due to the significant increase of the hydrophobic interaction potential.

Dynamic experiments on flocculation and sedimentation of argillized ultrafine tailings using fly-ash-based magnetic coagulant

In order to accelerate the sedimentation of super-large-scale argillized ultrafine tailings with bad features such as low settling velocity, muddy overflow water, and large flocculant dosage, a fly-ash-based magnetic coagulant （FAMC） was used in a dynamic experimental device. To obtain the best possible combination of the impact factors （magnetic intensity, FAMC dosage, flocculant dosage, and feed speed） for minimum overflow turbidity, a response surface methodology test coupled with a four-factor five-level central composite design was conducted. The synergy mechanism of FAMC and flocculant was analyzed based on the potential measurement and scanning electron microscopy. The results show that the flocculant dosage, overflow turbidity, and solid content can be reduced by 50%, 90%, and 80%, while the handling capacity per unit and efficiency of backfill and dry stacking can be promoted by 20%, 17%, and 13%, respectively, with a magnetic intensity of 0.3 T, FAMC dosage of 200 mL/t, flocculant dosage of 30 g/t, and feed speed of 0.6 t/（m^2·h）. Therefore, synergy of FAMC and flocculant has obvious efficiency in saving energy and protecting the environment by allowing 70×10^6 t/a of argillized ultrafine tailings slurry to be disposed safely and efficiently with a cost saving of more than 53×106 Yuan/a, which gives it great promise for use in domestic and foreign mines.

N-doped ordered mesoporous carbon as a multifunctional support of ultrafine Pt nanoparticles for hydrogenation of nitroarenes

Due to the advantages of high surface areas, large pore volumes and pore sizes, abundant nitrogen content that favored the metal-support interactions, N-doped ordered mesoporous carbons are regarded as a kind of fascinating and potential support for the synthesis of effective supported cat-alysts. Here, a N-doped ordered mesoporous carbon with a high N content （9.58 wt%）, high surface area （417 m^2/g）, and three-dimensional cubic structure was synthesized successfully and used as an effective support for immobilizing Pt nanoparticles （NPs）. The positive effects of nitrogen on the metal particle size enabled ultrasmall Pt NPs （about 1.0 ± 0.5 nm） to be obtained. Moreover, most of the Pt NPs are homogeneously dispersed in the mesoporous channels. However, using the ordered mesoporous carbon without nitrogen as support, the particles were larger （4.4 ± 1.7 nm） and many Pt NPs were distributed on the external surface, demonstrating the important role of the nitrogen species. The obtained N-doped ordered mesoporous material supported catalyst showed excellent catalytic activity （conversion 100%） and selectivity （〉99%） in the hydrogenation of halogenated nitrobenzenes under mild conditions. These values are much higher than those achieved using a commercial Pt/C catalyst （conversion 89% and selectivity 90%）. This outstanding catalytic perfor-mance can be attributed to the synergetic effects of the mesoporous structure, N-functionalized support, and stabilized ultrasmall Pt NPs. Moreover, such supported catalyst also showed excellent catalytic performance in the hydrogenation of other halogenated nitrobenzenes and nitroarenes. In addition, the stability of the multifunctional catalyst was excellent and it could be reused more than 10 times without significant losses of activity and selectivity. Our results conclusively show that a N-doped carbon support enable the formation of ultrafine metal NPs and improve the reaction ac-tivity and selectivity.

Purification of Ultrafine Diamond Synthesized by Detonation

Ultrafine diamond (UFD) is produced at high pressure and high temperature generated by explosive detonation. We manage to search for a new technology to purify the UFD by using potassium permanganate and concentrated sulfuric acid as oxidant. The experiment results show that, compared with others, the purifying effect by this technology is satisfactory and is a more efficient, cheaper, and safer purification technology with less pollution and less investment. It can be put into commercial use. The related principle of the technology is discussed. It is believed that the atomic state oxygen produced during the reaction mechanism is an active substances which would react with the graphite——the main impurity existing in the detonation soot, and the reaction temperature is the key factor in the process.

Application of Composite Ultrafine Particles in ER Fluids

Aim To obtain a kind of electrorheological (ER) flind with high comprehensive properties in order to satisfy the needs of engineering application. Methods A new type of dispersed phase── composite ultrafine particles (UFP) was obtained by the method of microemulsion, which was used to mix with silicon oil. aam electroinduced stress and apparent viscosity of the ER fluids with three different volume fractions were tested under the conditions of different temperatures, electric fields and shear rates. Results A series of systematic tests show that the new type of ER fluids with volume fraction of 30% possesses obvious ER effect. Conclusion The double layers polarization plays an important role in ER effect.

Preparation and hydrogen storage properties of ultrafine pure Mg and Mg-Ti particles

The ultrafine pure Mg and Mg-Ti particles were prepared through a direct current （DC） arc plasma method. The X-ray diffraction （XRD）, transmission electron microscopy （TEM）, pressure-composition-temperature （PCT） method and TG/DTA techniques were used to study the phase components, microstructure and hydrogen sorption properties of the powders before and after hydrogen absorption. It is revealed that most of the ultrafine Mg and Mg-Ti particles are hexagonal in shape with particle size in the range of 50-700 nm. According to the Van’t Hoff equation, the hydrogenation enthalpy of Mg-Ti powders is determined to be about -67 kJ/mol H2 based on the PCT curves of hydrogen absorption plateau pressures. This value is much higher than -78.6 kJ/mol H2 for pure Mg powders. TG/DTA analyses show that the onset dehydriding temperature of hydrogenated Mg-Ti powders is 386 °C, which is significantly lower than that of the hydrogenated Mg （423 °C）. The results prove that the addition of Ti into Mg through arc evaporation method can improve the thermodynamic properties of Mg for hydrogen storage.

PREPARATION OF ULTRAFINE METAL PARTICLES BY COMBINED METHOD γ-RAY RADIATION—HYDROTHERMAL CRYSTALLIZATION

The γ-ray radiation technique combined with hydrothermal crystallization was firstly used to prepare ultrafine metallic particles of An,Cu and Au-Cu alloy.Particle size for Au in average is about 10 nm.The morphologies were observed by TEM.The nucleation mechanism of metal particles and their stability are discussed.

EFFECT OF PRECIPITANT ON THE PROPERTIES OF ULTRAFINE YTTRIA POWDER PRODUCED BY PRE CIPITATION METHOD

Using yttriu m nitrate as the m other salt , synthesis of ultrafine yttria po w der through w et che mical route w as investigated . Choice of precipitant has dra m atic effects on co m position ,particle size distribution and particle m orphology of the precipitates . When a m m onia solutionw as used as the precipitant , the precursor precipitate w as m ainly Y2( O H) 5 14( N O3) 0 86· H2 O with co m paratively large particle size , broad size distribution and co m plex particleshapes . When sodiu m hydroxide solution w as used , roughly spherical α Y( O H)3·3 H2 Opre cipitate w ith sm all particle size and narro w size distribution w as obtained . The transfor m a tion sequence of dry α Y( O H)3 ·3 H2 O gel during calcination w as determ ined to be α Y( O H) 3·3 H2 O→ Y O O H→ Y2 O3 . After calcining at 600 ℃ for 1 hour , both Y2( O H) 5 14( N O3) 0 86· H2 O and α Y( O H) 3·3 H2 O transfor m to well crystallized Y2 O3 pow ders ,w ith particle sizes of 50 ～3000 n m and 20 n m , respectively .

Microstructures and Toughness of Weld Metai of Ultrafine Grained Ferritic Steel by Laser Welding

3 mm thick 400 MPa grade ultrafine grained ferritic steel plates were bead-on-plate welded by CO2 laser with heat input of 120-480 J/mm. The microstructures of the weld metal mainly consist of bainite, which form is lower bainite plates or polygonal ferrite containing quantities of dispersed cementite particles, mixed with a few of low carbon martensite laths or ferrite, depending on the heat input. The hardness and the tensile strength of the weld metal are higher than those of the base metal, and monotonously increase as the heat input decreases. No softened zone exists in heat affected zone (HAZ). Compared with the base metal, although the grains of laser weld are much larger, the toughness of the weld metal is higher within a large range of heat input. Furthermore, as the heat input increases, the toughness of the weld metal rises to a maximum value, at which point the percentage of lower bainite is the highest, and then drops.

Adsorption Behavior of Methyl Orange onto Modified Ultrafine Coal Powder

The adsorption of methyl orange onto ultrafine coal powder （UCP） and modified ultrafine coal powder （MUCP） from aqueous solutions were studied, in which the influence of contact time, dosage, temperature, pH, and methyl orange concentration in the solution were investigated. The adsorption kinetics of methyl orange by UCP and MUCP can be described by the Lagergren first-order and pseudo second-order kinetic models, respectively. The adsorption isotherms of methyl orange onto MUCP at 303, 313 and 323 K follow the Freundlich and Langmuir isotherm equation. Values of △G^0 for methyl orange adsorption onto MUCP are -22.55, -23.10 and -23.79 kJ·mol^-1 at 303, 313, and 323 K, respectively. The values of △H^0 and △S^0 are -3.74 kJ· mol^-1 and 61.99 J·mol^-1, respectively. The adsorption process is spontaneous and exothermic.

Ultrafine monolayer Co-containing layered double hydroxide nanosheets for water oxidation

For many two-dimensional(2D)materials,low coordination edges and corner sites offer greatly enhanced catalytic performance compared to basal sites,motivating the search for new synthetic approaches towards ultrathin and ultrafine 2D nanomaterials with high specific surface areas.To date,the synthesis of catalysts that are both ultrathin(monolayer)and ultrafine(lateral size<10nm)has proven extremely challenging.Herein,using a facile ultrasonic exfoliation procedure,we describe the successful synthesis of ultrafine ZnCo-LDH nanosheets(denoted as ZnCo-UF)with a size^3.5 nm and thickness^0.5 nm.The single layer ZnCo-UF nanosheets possess an abundance of oxygen vacancies(Vo)and unsaturated coordination s让es,thereby affording outstanding electrocatalytic water oxidation performance.DFT calculations confirmed that Vo on the surface of ZnCo-UF enhanced H20 adsorption via increasing the electropositivity of the nanosheets.

Preparation of ultrafine silver powders with controllable size and morphology

The ultrafine silver powders were prepared by liquid reduction method using Arabic gum as dispersant.The effects of different dispersants,pH values,and temperature on the morphology and particle size of silver powders were investigated.It is found that Arabic gum can better adsorb on silver particles via chemical adsorption,and it shows the best dispersive effect among all the selected dispersants.The particle size of silver powders can be finely tuned from 0.34 to 4.09μm by adjusting pH values,while the morphology of silver powders can be tuned by changing the temperature.The silver powders with high tap density higher than 4.0 g/cm3 were successfully prepared in a wide temperature range of 21.8-70°C.Especially,the tap density is higher than 5.0 g/cm3 when the temperature is optimized to be 50°C.The facile process and high silver concentration of this method make it a promising way to prepare high quality silver powders for electronic paste.

Solvent-Free Synthesis of Ultrafine Tungsten Carbide Nanoparticles-Decorated Carbon Nanosheets for Microwave Absorption

Carbides/carbon composites are emerging as a new kind of binary dielectric systems with good microwave absorption performance.Herein,we obtain a series of tungsten carbide/carbon composites through a simple solvent-free strategy,where the solid mixture of dicyandiamide(DCA)and ammonium metatungstate(AM)is employed as the precursor.Ultrafine cubic WC1-x nanoparticles(3-4 nm)are in situ generated and uniformly dispersed on carbon nanosheets.This configuration overcomes some disadvantages of conventional carbides/carbon composites and is greatly helpful for electromagnetic dissipation.It is found that the weight ratio of DCA to AM can regulate chemical composition of these composites,while less impact on the average size of WC1-x nanoparticles.With the increase in carbon nanosheets,the relative complex permittivity and dielectric loss ability are constantly enhanced through conductive loss and polarization relaxation.The different dielectric properties endow these composites with distinguishable attenuation ability and impedance matching.When DCA/AM weight ratio is 6.0,the optimized composite can produce good microwave absorption performance,whose strongest reflection loss intensity reaches up to-55.6 dB at 17.5 GHz and qualified absorption bandwidth covers 3.6-18.0 GHz by manipulating the thickness from 1.0 to 5.0 mm.Such a performance is superior to many conventional carbides/carbon composites.