Recent progresses in thermal treatment of β-Ga_(2)O_(3) single crystals and devices

In recent years,ultra-wide bandgap β-Ga_(2)O_(3) has emerged as a fascinating semiconductor material due to its great potential in power and photoelectric devices.In semiconductor industrial,thermal treatment has been widely utilized as a convenient and effective approach for substrate property modulation and device fabrication.Thus,a thorough summary of β-Ga_(2)O_(3) substrates and devices behaviors after high-temperature treatment should be significant.In this review,we present the recent advances in modulating properties of β-Ga_(2)O_(3) substrates by thermal treatment,which include three major applications:(ⅰ)tuning surface electrical properties,(ⅱ)modifying surface morphology,and(ⅲ)oxidating films.Meanwhile,regulating electrical contacts and handling with radiation damage and ion implantation have also been discussed in device fabrication.In each category,universal annealing conditions were speculated to figure out the corresponding problems,and some unsolved questions were proposed clearly.This review could construct a systematic thermal treatment strategy for various purposes and applications of β-Ga_(2)O_(3).

The effects of radio frequency atmospheric pressure plasma and thermal treatment on the hydrogenation of TiO_(2) thin film

The effects of radio frequency(RF)atmospheric pressure(AP)He/H_(2)plasma and thermal treatment on the hydrogenation of TiO_(2)thin films were investigated and compared in this work.The color of the original TiO_(2)film changes from white to black after being hydrogenated in He/H_(2)plasma at160 W(gas temperature~381℃)within 5 min,while the color of the thermally treated TiO_(2)film did not change significantly even in pure H_(2)or He/H_(2)atmosphere with higher temperature(470℃)and longer time(30 min).This indicated that a more effective hydrogenation reaction happened through RF AP He/H_(2)plasma treatment than through pure H_(2)or He/H_(2)thermal treatment.The color change of TiO_(2)film was measured based on the Commission Internationale d’Eclairage L*a*b*color space system.Hydrogenated TiO_(2)film displayed improved visible light absorption with increased plasma power.The morphology of the cauliflower-like nanoparticles of the TiO_(2)film surface remained unchanged after plasma processing.X-ray photoelectron spectroscopy results showed that the contents of Ti3+species and Ti-OH bonds in the plasma-hydrogenated black TiO_(2)increased compared with those in the thermally treated TiO_(2).X-ray diffraction(XRD)patterns and Raman spectra indicated that plasma would destroy the crystal structure of the TiO_(2)surface layer,while thermal annealing would increase the overall crystallinity.The different trends of XRD and Raman spectra results suggested that plasma modification on the TiO_(2)surface layer is more drastic than on its inner layer,which was also consistent with transmission electron microscopy results.Optical emission spectra results suggest that numerous active species were generated during RF AP He/H_(2)plasma processing,while there were no peaks detected from thermal processing.A possible mechanism for the TiO_(2)hydrogenation process by plasma has been proposed.Numerous active species were generated in the bulk plasma region,accelerated in the sheath region,and bumped toward the TiO_(2)film,which will react with the TiO_(2)surface to form OVs and disordered layers.This leads to the tailoring of the band gap of black TiO_(2)and causes its light absorption to extend into the visible region.

Comparison of microwave- and thermal-assisted rock fragmentation methods at different temperatures and loading rates

Understanding the effects of microwave irradiation and thermal treatment on the dynamic compression and fragmentation properties of rocks is essential to quantify energy consumption in rock engineering.In this study,Fangshan granite(FG)specimens were exposed to microwave irradiation and heat treatment.The damage of FG specimens induced by these two methods was compared using X-ray CT scanning and ultrasonic wave method.The temperatures of FG after microwave irradiation and thermal treatment were effectively evaluated using a newly proposed technique.A novelty method for precisely determining the geometric features of fragments is developed to estimate the fragmentation energy.Thus,the dynamic uniaxial compressive strength(UCS),the dynamic fragmentation characteristics,and the fragmentation energy of FG after these two pretreatment methods can be reasonably compared.The noticeable distinction of loading rate effect on the dynamic UCS of FG between these two pretreatment methods is first observed.A relationship is established between the dynamic UCS and the damage induced by microwave irradiation and heat treatment.Moreover,fragmentation energy fan analysis is introduced to accurately compare the fragmentation properties of FG after two pretreatment methods in dynamic compression tests.

Mechanical properties and fracture surface roughness of thermally damaged granite under dynamic splitting

In order to understand the mechanical properties and the fracture surface roughness characteristics of thermally damaged granite under dynamic splitting,dynamic Brazilian splitting tests were conducted on granite samples after thermal treatment at 25,200,400,and 600℃.Results show that the dynamic peak splitting strength of thermally damaged granite samples increases with increasing strain rate,showing obvious strain‐rate sensitivity.With increasing temperature,thermally induced cracks in granite transform from intergranular cracks to intragranular cracks,and to a transgranular crack network.Thermally induced damages reduce the dynamic peak splitting strength and the maximum absorbed energy while increasing the peak radial strain.The fracture mode of the thermally damaged granite under dynamic loads is mode Ⅱ splitting failure.By using the axial roughness index Z2 a,the distribution ranges of the wedge‐shaped failure zones and the tensile failure zones in the fracture surfaces under dynamic Brazilian splitting can be effectively identified.The radial roughness index Z_(2)^(r)is sensitive to the strain rate and temperature.It shows a linear correlation with the peak splitting strength and the maximum absorbed energy and a linear negative correlation with the peak radial strain.Z_(2)^(r)can be used to quantitatively estimate the dynamic parameters based on the models proposed.

Comparison of mechanical properties in high temperature and thermal treatment granite

Static mechanical experiments were carried out on granite after and under different temperatures using an electro-hydraulic and servo-controlled material testing machine with a heating device. Variations in obvious form, stress-strain curve, peak strength, peak strain and elastic modulus with temperature were analyzed and the essence of rock failure modes was explored. The results indicate that, compared with granite after the high temperature treatment, the brittle-ductile transition critical temperature is lower, the densification stage is longer, the elastic modulus is smaller and the damage is larger under high temperature. In addition, the peak stress is lower and the peak strain is greater, but both of them change more obviously with the increase of temperature compared with that of granite after the high temperature treatment. Furthermore, the failure modes of granite after the high temperature treatment and under high temperature show a remarkable difference. Below 100 ℃, the failure modes of granite under both conditions are the same, presenting splitting failure. However, after 100 ℃, the failure modes of granite after the high temperature treatment and under high temperature present splitting failure and shear failure, respectively.

Microstructure evolution and thermal expansion of Cu-Zn alloy after high pressure heat treatment

The thermal expansion coefficients of Cu-Zn alloy before and after high pressure treatment were measured by thermal expansion instrument in the temperature range of 25？700 ℃,and the microstructure and phase transformation of the alloy were examined by optical microscope,X-ray diffractometer（XRD） and differential scanning calorimeter（DSC）.Based on the experimental results,the effects of high pressure treatment on the microstructure and thermal expansion of Cu-Zn alloy were investigated.The results show that the high pressure treatment can refine the grain and increase the thermal expansion coefficient of the Cu-Zn alloy,resulting in that the thermal expansion coefficient exhibits a high peak value on the α-T curve,and the peak value decreases with increasing the pressure.

Thermal Treatment for Decreasing the Acidity of Crude Oil

Highly acidic crude oil is thermally soaked to investigate how the temperature and time involved affect the removal of organic acid in feedstock. Experimental results indicate that thermal treatment is an effective approach to decreasing acidity and the acid removal rate reaches 80%. Temperature is one of the main factors that determine the acid removal reaction. When the temperature ranges from 420oC to 440oC, the acid removal rate increases with the rise of the reaction temperature, but the increase slows down gradually. At the reaction temperature below 440oC, the long reaction time favors the acid removal. The cracking and polymerization of hydrocarbon molecules take place so that the properties of the crude oil change at the same time when the highly acidic crude is thermally treated.

THERMAL RATE TREATMENT AND ITS EFFECT ON MODIFICATION OF Al-Si ALLOYS

ＴＨＥＲＭＡＬＲＡＴＥＴＲＥＡＴＭＥＮＴＡＮＤＩＴＳＥＦＦＥＣＴＯＮＭＯＤＩＦＩＣＡＴＩＯＮＯＦＡｌＳｉＡＬＬＯＹＳ①ＧｅｎｇＨａｏｒａｎ，ＭａＪｉａｊｉ，ＢｉａｎＸｏｕｆａｎｇＣｏｌｌｅｇｅｏｆＭａｔｅｒｉａｌｓＳｃｉｅｎｃｅａｎｄＥｎｇｉｎｅｒ...

Effects of cryogenic treatment on the thermal physical properties of Cu_(76.12) Al_(23.88) alloy

The thermal diffusion coefficient, heat capacity, thermal conductivity, and thermal expansion coefficient of Cu76.12Al23.88 alloy before and after cryogenic treatment in the heating temperature range of 25℃ to 600℃ were measured by thermal constant tester and thermal expansion instrument. The effects of cryogenic treatment on the thermal physical properties of CU76,12A123,88 alloy were investigated by comparing the variation of the thermal parameters before and after cryogenic treatment. The results show that the variation trend of the thermal diffusion coefficient, heat capacity, thermal conductivity, and thermal expansion coefficient of CU76.12Al23.88 alloy after cryogenic treatment was the same as before. The cryogenic treatment can increase the thermal diffusion coefficient, thermal conductivity, and thermal expansion coeffi- cient of Cu76.12Al23.88 alloy and decrease its heat capacity. The maximum difference in the thermal diffusion coefficient between the before and after cryogenic treatment appeared at 400℃. Similarly, thermal conductivity was observed at 200℃.

Effect of thermal treatment on energy dissipation of granite under cyclic impact loading

High temperature treatment causes thermal damage to rocks in deep mining.To study the thermal effect on the energy dissipation of rocks during the dynamic cyclic loading,cyclic impact loading experiments of heat-treated rocks were carried out using the splitting Hopkinson pressure bar(SHPB)experimental system.The correlations among the energy dissipation,energy dissipation rate,impact times,accumulated absorbed energy per volume,failure mode and temperature were analyzed.The results show that the reflected energy under the first impact increases and finally exceeds the absorbed energy when the temperature increases;however,the total reflected energy decreases above 200℃.The absorbed energy under the first impact and the total absorbed energy all decrease as the temperature increases,the rates of which decrease accordingly.And the same phenomenon appears for the transmitted energy and the rate of the transmitted energy.On the contrary,the rate of the reflected energy increases with the rising temperature.When the temperature increases,the fewer impact times are needed to destroy the sample.In addition,the failure modes are different when the rock is treated at different temperatures;that is,when the temperature is high,even though the absorbed energy is low,the sample breaks into powder after several impacts.

Numerical Simulation on Thermal Stress of Large-scale Bearing Roller during Heating Process of Final Heat Treatment

hi this paper, the non-linear finite element method had been applied to calculate the thermal stress evolving process of the large-scale bearing roller during heating process of final heat treatment. It was found that two stress peaks appeared during heating process and the second stress peak was higher than the first. If the preheating time was elongated, the second stress peak was reduced distinctly. Therefore, the pre-heating time should be elongated suitably to ensure safety in the practical manufacture process.

Influence of Thermal Treatments on In-depth Compositional Uniformity of Culn（S,Se）2 Thin Films

CuIn（S,Se）2 thin films were prepared by thermal crystallization of co-sputtered Cu-In alloy precursors in S/Se atmosphere. In-depth compositional uniformity is an important prereq- uisite for obtaining device-quality CuIn（S,Se）2 absorber thin films. In order to figure out the influence of heat treatments on in-depth composition uniformity of CuIn（S,Se）2 thin films, two kinds of reaction temperature profiles were investigated. One process is ＂one step profile＂, referring to formation of CuIn（S,Se）2 thin films just at elevated temperature （e.g. 500 ℃）. The other is ＂two step profile＂, which allows for slow diffusion of S and Se elements into the alloy precursors at a low temperature before the formation and re-crystallization of CuIn（S,Se）2 thin films at higher temperature （e.g. first 250 ℃ then 500 ℃）. X-ray diffrac- tion studies reveal that there is a discrepancy in the shape of （112） peak. Samples annealed with ＂one step profile＂ have splits on （112） peaks, while samples annealed with ＂two step profile＂ have relatively symmetrical （112） peaks. Grazing incident X-ray diffraction and en- ergy dispersive spectrum measurements of samples successively etched in bromine methanol show that CuIn（S,Se）2 thin films have better in-depth composition uniformity after ＂two step profile＂ annealing. The reaction mechanism during the two thermal processing was also investigated by X-ray diffraction and Raman spectra.

Effects of Chemical Treatments on Thermal Expansion Properties of Cordierite Ceramics

Cordierite honeycomb ceramics was treated with 1.5 M HNO3 , followed with 1.5 M NaOH at 93 ℃. The combination of acid treatment with alkali treatment significantly diminished the rebounding of coefficient of thermal expansion （CTE） caused by heat treatment, a phenomenon observed in samples treated solely with acid. Inductively coupled plasma （ICP） analysis results reveal that the alkali treatment preferentially dissolved ＂free＂ SiO2 left in the acid-treated samples, which is considered to be a key factor responsible for the CTE rebounding.

Influence of Different Surface Treatments of H13 Hot Work Die Steel on Its Thermal Fatigue Behaviors

Thermal fatigue checking is the general failure of hot work die steels, which is relative with the structures and properties of the steels and the stress alternated during the employment. The Uddeholm test method on thermal fatigue is used to compare the behaviors of different samples, which are treated with plasma nitriding、plasma sulfur carbon nitriding、boronizing or not treated. The results show that the nitriding improves the thermal fatigue property of the tool steel, while the plasma sulfur carbon nitriding and the boronizing impair the property. The mechanisms are induced as follows. By increasing the hardness and changing the stress distribution in the surface layer, surface treatment can decrease the plastic deformation and the tensile stress during the cycling. Therefore, the generation and growth of the cracks are restrained. On the other hand, as results of surface treating, in the surface layer the toughness declines and the expanding coefficient ascendes; the latter change caused the strengthening of the tensile and compressive stress during the cycling. Thus the resistance to thermal fatigue is weakened. Whether or not the surface treatment is favor to thermal fatigue of tool steels relies on which factor is dominant.

Effect of thermal-cooling cycle treatment on thermal expansion behavior of particulate reinforced aluminum matrix composites

Two micron SiC particles with angular and spherical shape and the sub-micron Al2O3 particles with spherical shape were introduced to reinforce 6061 aluminium by squeeze casting technology. Microstructures and effect of thermal-cooling cycle treatment （TCCT） on the thermal expansion behaviors of three composites were investigated. The results show that the composites are free of porosity and SiC/Al2O3 particles are distributed uniformly. Inflections at about 300℃ are observed in coefficient of thermal expansion （CTE） versus temperature curves of two SiCp/Al composites, and this characteristic is not affected by TCCT. The TCCT has significant effect on thermal expansion behavior of SiCp/Al composites and CTE of them after 3 cycles is lower than that of 1 or 5 cycles. However, no inflection is observed in Al2O3p/Al composite, while TCCT has effect on CTE of Al2O3p/Al composite. These results should be due to different relaxation behavior of internal stress in three composites.

Effects of Melt Thermal Treatment on A356 Alloy

To increase the casting quality of hypoeutectic Al-Si alloys, the effects of melt thermal treatment on the solidification structure of the A356 alloy were analyzed by a factorial experiment, in which the overheated melt was mixed with the low temperature melt. Experimental results show that the elongation ratio and strength of the treated samples increase remarkably compared with the control sample. The primary dendrite size reduces dramatically and the dendrite changes from columnar to equiaxed, with a little change of the secondary dendrite arm spacing (SDAS). Combined with the measurement of the nucleation undercooling, it is concluded that the solidification structure and refining effect are dependent primarily on the low temperature melt. The refining mechanism is believed as a result of the multiplication of the nuclei in the melt thermal treatment procedure.

Effect of Thermal Treatment and Acid Leaching Process on Pore Characteristics of Nanometer Porous Glass

Porous glass was prepared by thermally treating sodium borosilicate glass for different time, the effect of thermal treatment on pore size distribution was discussed and the pore size of the prepared porous glass was measured by scanning electron microscopy （SEM） and differential thermal analysis （DTA）. The results show that the optimum porous glass with an average diameter of 80 nm can be prepared by thermal treatment at 600℃ for 12 h and then acid treatment for 12 h in 2 mol·L^-1 hydrochloric acid solution.

Impacts of freezing and thermal treatments on dimensional and mechanical properties of wood flour-HDPE composite

Wood plastic composite （WPC） of wood flour （WF）, high density polyethylene （HDPE）, maleic anhydride-grafted polyethylene （MAPE） and lubricant was prepared by extrusion, and then exposed to different temperatures to evaluate the effects of freezing and thermal treatment on its dimensional and mechanical properties. At elevated temperatures, WPC expanded rapidly initially, and then contracted slowly until reaching an equilibrium state. Treatment at 52°C and relative humidity of 50% for 16 days improved the mechanical properties of WPC： flexure, tensile strength, and izod unnotched impact strength increased by 8%, 10% and 15%, respectively. Wide-angle X-ray diffraction （XRD） tests showed that the degree of crystalization of HDPE in WPC declined with increasing treatment temperature.

EFFECTS OF HEAT TREATMENT ON THE THERMAL EXPANSION BEHAVIOR OF SiC WHISKER REINFORCED ALUMINUM COMPOSITE

The thermal expansion behaviors of commercially-available SiC whisker reinforced pure aluminum composites subjected to different heat treatments were studied. The results indicated that the thermal expansion behaviors were greatly affected by heat treatment. To explain the results, the microstructures and thermal mismatch stresses in the matrix of the composite were examined by the transmission electron microscope and X-ray diffraction, respectively. The results show that the dislocation density and thermal mismatch stresses in the matrix of the composites water-quenched from 600°C are much higher than those of the composite slowly cooled from 600°C. The analysis suggests that the coefficients of thermal expansion (CTE) are closely related to the change of thermal mismatch stresses and the yield strength of the matrix of the composite. The comparison of the coefficients of thermal expansion between experiments and calculations suggests that the temperature behaviors of CTE of SiC/Al composite agree better with those of Kerner's model within lower temperature range.

Microstructural Characteristic of Montmorillonite and Its Thermal Treatment Products

The montmorillonite was studied by differen t methods, such as chemical analysis, DAT, TG, X RD, IR, AFM and MAS NMR. The experimental results show that the hydroxyl in octa hedra sheets begins dehydrating when the thermal treatment temperature reaches 659℃, but th e layer structure remains the same,and the corresponding Al(Ⅵ) is turned into Al(Ⅳ) in octahedra sheets. When the temperature reaches 900℃, the layer struct ure of montmorillontite is destroyed, and the new mineral phase μ-cordierite i s found. When the temperature reaches 1200℃, the μ-cordierite phase loses its stability, and decomposes into cristobalite phase and mullite phase.Meanwhile, the recrystallization phenomenon in thermal treatment products is obvious. There is a small quantity of Al Ⅵ signal in MAS NMR spectrum, corresponding to Al of mullite. When the temperature reaches 1350℃, the cristobalite and mullite phases reduce slightly, and more Fe-cordierite phase appears, corresponding to Fe-cordierite spectrum in XRD and MAS NMR.