UV-curing of hyperbranched polyurethane acrylate-polyurethane diacrylate/SiO_2 dispersion and TGA/FTIR study of cured films

UV-curable hyperbranched polyurethane acrylate-polyurethane diacrylate/SiO2 dispersion （HBPUA-PUDA/SiO2） was prepared with isophorone diisocyanate （IPDI）, hyperbranched polyester Boltorn H20 （H20）, hydroxy-ethyl acrylate （HEA）, polyethyleneglycol （PEG-200）and nano-SiO2. The UV curing kinetics of the films was investigated by FTIR. The results show that the curing speed of the films increases with the adding of nano-SiO2 and decreases with the adding of PUDA due to the slower chain movement. The thermal stability of the HBPUA-PUDA/SiO2 films was studied by using thermogravimetric analysis coupled with Fourier transform infrared spectroscopy （TGA/FTIR）. The results show that all films exhibit two degradation stages located at about 320 and 440℃ corresponding to the degradation for hard segments of urethane-acrylate and the degradation for soft segment and polyester core. In addition, the results from the analysis of TGA/FTIR also indicate that the decomposition temperature of HBPUA-PUDA/SiO2 film is 15℃ higher than that obtained for pure polymer. The degradation mechanism was proposed according to TGA/FTIR results.

Synthesis and properties of UV curable polyurethane acrylates based on two different hydroxyethyl acrylates

Two kinds of UV curable polyurethane acrylate oligomers （PUPA and PUCA） were synthesized via the addition reaction between isophorone diisocyanate （IPDI） and polyethylene glycol monoacrylate （PEA6） or polycaprolactone modified hydroxyethyl acrylate （PCLA2）. The structures of PUPA and PUCA were characterized by Fourier transform infrared spectroscopy （FT-IR）, IH nuclear magnetic resonance （^H NMR）, gel permeation chromatography （GPC） and differential scanning calorimeter （DSC）, and the thermal stability and dynamic mechanical thermal properties of their cured films were measured by thermogravimetric analysis （TGA） and dynamic mechanical analysis （DMA）, respectively. The viscosity of the oligomers and mechanical properties of the cured films were also studied. The results show that both oligomers have narrow molecular weight distribution. The viscosity of PUPA is 2.310 Pa.s at 25 ℃, while that of PUCA is： up to 3.980 Pa-s. The UV cured PUPA and PUCA films have homogeneous phase structure, and the PUCA film shows higher glass transition temperature and storage modulus. Furthermore, the PUCA film possesses better mechanical properties than PUPA, while the latter shows better alkali resistance.

Water-soluble UV curable urethane methyl acrylate coating：preparation and properties

Two kinds of water-soluble and ultraviolet (UV) curable oligomers were synthesized and characterized. The oligomers were evaluated as resins for water-based UV curable coating. The rheology of the two oligomers' aqueous so-lutions was investigated in terms of solid fraction, pH dependence, and temperature dependence. The solutions were found to be Newtonian fluid showing rather low viscosity even at high solid fraction of 0.55. The drying process of the coatings and the properties of the cured coatings were studied by comparing them with water-dispersed UV-curable polyurethane methyl acrylate. It was evident that the water-soluble coating dried more slowly; and that the overall properties were inferior to those of the water-dispersed coating.

Hyperbranched Polyurethane Acrylate Applied to UV Curable Flame Retardant Coatings

UV curable hyperbranched prepolymers based on amine-ester, ester-amide and ether-amide started with AB_2-type monomers have been prepared by the authors. A series of work on allyl ether maleate hyperbranched polyesters for UV curing coatings by Hult and his colleagues has been reported. However, the UV cured films from those materials are all flammable when attached to fire without addition of flame retardants.

Lithium bis(trifluoromethanesulfonyl)imide blended in polyurethane acrylate photocurable solid polymer electrolytes for lithium-ion batteries

The increased demand of electronic devices promotes the development of advanced and more efficient energy storage devices, such as batteries. Lithium-ion batteries (LIBs) are the most studied battery systems due to their high performance. Among the different battery components, the separator allows the control of lithium ion diffusion between the electrodes. To overcome some drawbacks of liquid electrolytes, including safety and environmental issues, solid polymer electrolytes (SPEs) are being developed. In this work, a UV photocurable polyurethane acrylate (PUA) resin has been blended with lithium bis(trifluoromethanesulfonyl) imide (LiTFSI) up to 30 wt% LiTFSI content to reach a maximum ionic conductivity of 0.0032 mS/cm at room temperature and 0.09 mS/cm at 100 ℃. Those values allowed applying the developed materials as photocurable SPE in Swagelok type Li/C-LiFePO_(4) half-cells, reaching a battery discharge capacity value of 139 mAh.g^(−1) at C/30 rate. Those results, together with the theoretical studies of the discharge capacity at different C-rates and temperatures for batteries with LiTFSI/PUA SPE demonstrate the suitability of the developed photocurable SPE for LIB applications.

Preparation and Surface Properties of Silicon-Containing Waterborne Polyurethane Functionalized with Fluorine-Containing Acrylate and Micro-Nano Silica

In order to prepare hydrophobic waterborne polyurethane coatings with better performances, the silicon-containing waterborne polyurethane（SiWPU） with functional chain extender hydroxyethyl acrylate（HEA） was prepared first, and then a series of silicon＆fluorine-containing polyurethane/acrylate（FSiPUA） emulsions were obtained with flourine containing acrylic monomer by seed emulsion polymerization, introducing micro-nano SiO2 into FSiPUA emulsion to make the final hybrid emulsion. The properties of Si WPU, FSiPUA and SiO2/FSiPUA were investigated by fourier transform infrared spectra（FTIR）, transmission electron microscope（TEM）, Scanning Electron Microscope（SEM） and some other analytical methods. The results revealed that FSiPUA emulsion particles possessed composite core-shell structure and FSiPUA films with suitable ratio performed better than Si WPU films in hardness, water resistance and solvent resistance. The SiO2/FSiPUA films with micro-nano dual roughness structure showed a water contact angle of 136° with good resistance to acid and alkali.

Use of the Newly Synthesized Aqueous Polyurethane Acrylate Binders for Printing Cotton and Polyester Fabrics

The use of the four new synthesized polyurethane acrylate binders in the pigment print paste for screen printing cotton and polyester fabrics and pigment fixation through the polymerization process of the binder by using the thermofixation technique as well as the UV curing technique was studied. The effect of changing time and temperature of thermofixation, and the time of UV curing on the color strength, and prints fastness properties were also studied. The results showed that, the newly synthesized polyurethane acrylate binders could be successfully used for pigment fixation on cotton and polyester using the two fixation techniques and in general their prints possessed better color strength values as compared to those obtained upon using the selected commercial binders.

Preparation, morphology and mechanical properties of acrylate-modified polyurethane/unsaturated polyester resin graft-IPNs

Acrylate modified polyurethane resin was first synthesized, and interpenetrated with unsaturated polyester resin to form IPNs and gradient IPNs which cured at room temperature. The polymerization process was traced by an IR spectroscopy technique and the simultaneous interpenetrating techniques were determined. The morphology of these IPNs were estimated by TMA and TEM methods. The results indicated that large amount of interpenetrating and entanglement make T g linked up effectively, and domains between two phases can be in nanometre ranges, which changed with composition ratios. The mechanical properties results showed that IPNs varied from elastomeric to plastic materials. It was noteworthy that, with the introduction of modified groups and the formation of graft construction in IPNs, the miscibility in the systems was improved a lot. These further led to the improved mechanical properties of IPNs with elastomer reinforced and plasticizer toughened as well. The reinforced miscibility between the networks can apparently change mechanical property especially for the gradient ones when the materials are elongated.

PREPARATION AND MECHANICAL PROPERTIES OF POLY(METHYL METHACRYLATE)/ URETHANE ACRYLATE COPOLYMERS

The urethane acrylate(UA) was made of poly(tetramethylenc oxide), 4,4’-diphenylmethane diisocyanate, and 2-hydroxyethyl methacrylate. A series of poly(methyl methacrylate) / urethane acrylate copolymers was prepared by using a redox initiating system. The copolymers had cross linked structures and two-phase morphologies as indicated by the results of the dynamic mechanical measurement and swelling test.

Part 1: Synthesis and Evaluation of Novel Nano Scale Powdered Polyurethane Acrylate Binders

Some new an aqueous polyurethane acrylate (waterborne binder) based on polyethylene glycol with different M. wt. mixed with polyol were carried out. Seven different polyurethane acrylate co-polymers were prepared aiming at substituting the two hydroxyl groups of polyethylene glycol (6000, 12,000 and 20,000 g/mol) and two primary hydroxyl groups of polyol through their reaction with corresponding calculated amounts of either isophorone diisoyanate or toluene diisocyanate and caped the remaining isocyanate group with either hydroxy ethyl acrylate or hydroxy propyl methacrylate to get on the polyurethane acrylate polymers [PUA]. From DSC measurement the result of Tg of synthesized PUA are in range from -8.78℃ to 36.4℃. So they can classify as soft binders. The infrared spectra, rheological properties, viscosity measurement, the weight average molecular weight, of the synthesize binders were investigated.

PROPERTIES AND MORPHOLOGY OF UNSATURATED POLYESTER/ACRYLATE-TERMINATED POLYURETHANE/ORGANO-MONTMORILLONITE NANOCOMPOSITES

Unsaturated polyester resin （UPR）/acrylate-terminated polyurethane （ATPU）/organo-modified montmorillonite （OMMT） nanocomposites were prepared by the in situ intercalative polymerization method. Samples were prepared by the sequential mixing, i.e. mixture of the ATPU and styrene （S） and OMMT were prepared in the first step; UPR was then added to the pre-intercalates of ATPU/S/OMMT. Results indicate that the mechanical properties and thermal properties of UPR/ATPU/OMMT nanocomposites greatly depend on the amount of ATPU and OMMT. Results show that the addition of ATPU could increase the impact strength of UPR/ATPU composites, but the tensile strength, flexural strength and heat resistance of the materials are obviously decreased. When the weight ratio between UPR, ATPU and OMMT were 82：15：3, the impact strength and heat distortion-temperature of nanocomposite were greatly improved, meanwhile there was little change for other properties of the nanocomposites. The synergistic enhancement effects of ATPU and OMMT on the composites were observed. The structures and morphology of the composites were investigated by X-ray diffraction, scanning electron microscopy and transmission electron microscopy.

MODIFIED ULTRAVIOLET-CURABLE WATER DISPERSIBLE POLYURETHANE-ACRYLATES

Three kinds of UV-curable self-emulsified polyurethane-acrylate (PUA) prepolymer, i.e., conventional, chain extended and grafted PUAs, were prepared. The relatively small particle size of the PUA dispersions indicates that the PUA prepolymers exhibit sufficient aqueous dispersibility. The PUA prepolymers can substantially lower the interfacial tension of water. Chain-extended PUA dispersions exhibit pseudoplastic behavior and thixotropy to a greater extent than do their conventional counterpart. The chain-extended and grafted PUA photocure to higher conversion than do the conventional PU equivalent. The results of DSC measurement suggest that there exists phase mixing between the hard and the soft segment phases for the PUAs based on PEG 400 that is the comparatively short soft segment in the prepolymer. For the PUA prepolymers based on PEG having higher M-n values, chain-extending and grafting could impede the phase separation between the hard and the soft segment domains. The adhesion, impact strength and flexibility of the photocured films were tested.

Influence of Initiator on Synthesis and Properties of Polyurethane-acrylate Hybrid Emulsion

The prepolymer polyurethanes （PUs） based on isophorone diisocyanate （IPDI）, poly（propylene glycol） （PPG）, 1,4-butanediol （BDO） and dimethylopropionic acid （DMPA） were synthesized at 75-80 ℃ for 7-8 hours, using dibutyltin dilauate （DBTDL） as catalyzer, and polyurethane-acrylate hybrid emulsion was prepared after methyl methacrylate （MMA） was polymerized, using potassium persulfate and azobisisobutyronitrile （AIBN） as initiator, respectively. The influences of these factors such as the kind of initiator, the feed method of initiator and the addition of initiator on properties of polyurethane-acrylate were studied. The FTIR and GPC of aqueous polyurethane were analyzed. The FTIR spectra show that the degree of microphase-separate between the soft segments and rigid segments is high. The analysis of molecular weights stated that molecular weights increased most significantly after amine was added. The experimental results reveal that the appearance of emulsion is excellent, the film is harder and the water absorption radio of the film is less when oil-solubility AIBN is used as initiator. The semi-continuous can increase the molecular weight of polymer and the optimum amount of the initiator was 3% for MMA.

Removal of Dye Using Lignin-Based Biochar/Poly(ester amide urethane)Nanocomposites from Contaminated Wastewater

The pursuit of incorporating eco-friendly reinforcing agents in polymer composites has accentuated the exploration of various natural biomass-derived materials.The burgeoning environmental crisis spurred by the discharge of synthetic dyes into wastewater has catalyzed the search for effective and sustainable treatment technologies.Among the various sorbent materials explored,biochar,being renewable,has gained prominence due to its excellent adsorption properties and environmental sustainability.It has also emerged as a focal point for its potential to replace other conventional reinforcing agents,viz.,fumed silica,aluminum oxide,treated clays,etc.This study introduces a novel class of polymer nanocomposites comprising of lignin-based biochar particles and poly(ester amide urethane)matrix via a feasible method.The structural evaluation of these nanocomposites was accomplished using Fourier-transform infrared spectroscopy,X-ray photoelectron spectroscopy,and powder X-ray diffraction.The polymer nanocomposites exhibited superior mechanical properties with an increment in tensile strength factor by 45%in comparison to its pristine matrix,along with an excellent toughness value of 90.22 MJm^(−3)at a low loading amount of only 1 wt%.The composites showed excellent improvement in thermal properties with a sharp rise in the glass transition temperature(Tg)value from−28.15℃to 84℃,while also championing sustainability through inherent biodegradability attributes.Beyond their structural prowess,these polymer nanocomposites demonstrated excellent potential as adsorbents,displaying efficient removal of malachite green and tartrazine dyes from aqueous systems with a removal efficiency of 87.25%and 73.98%,respectively.The kinetics study revealed the pseudo second order model to be the precision tool to assess the dye removal study.Complementing this,the Langmuir adsorption isotherm provided a framework to assess the sorption features of the polymer nanocomposites.Overall,these renewable biochar integrated polymer matrices boast remarkable recovery capabilities up to seven cycles of usage with an excellent dye recovery percentage of 95.21%for the last cycle,thereby defining sustainability as well as economic feasibility.

Incorporation of Reactive Corrosion Inhibitor in Waterborne Acrylic Polyurethane Coatings and Evaluation of its Corrosion Performance

Hydroxyl-epoxy phosphate （HEP） as a reactive corrosion inhibitor was innovatively synthe- sized by the reaction of bisphenol A epoxy resin with phosphoric acid. HEP was mixed with hydroxyl acrylate resin, and crosslinked with waterborne isocyanate curing agent, which was used to form waterborne HEP/acrylic polyurethane composite （HEP-APU） coatings on Q235 steel surfaces. Electrochemical impedance spectroscopy and polarization curves were applied to analyze the corrosion behavior of the HEP-APU coatings in 3.5wt% NaCl solutions. The results indicated that the HEP-APU coatings show a superior passivation property and efficient corrosion protection of Q235 steel. The waterborne acrylic polyurethane coating containing 0.5wt% HEP exhibited the best corrosion performance among all the coating specimens. The improved flash-rust resistance can be attributed to the introduction of the phosphate group which could form phosphate film on the steel substrate.

Polyurethanes from Kraft Lignin without Using Isocyanates

The reaction of a desulphurized kraft lignin with hexamethylene diamine and dimethyl carbonate has allowed the development of isocyanate-free polyurethane resins.The present research work is based on previous studies made with hydrolyzable and condensed tannins,but takes advantage of the higher number of hydroxyl groups present in lignin and their different aliphatic and aromatic character.The obtained materials were analyzed by Fourier transform infrared(FTIR)spectroscopy,matrix-assisted laser desorption ionization time-of-flight(MALDI-TOF)mass spectrometry and solid-state cross-polarization/magic angle spinning(CP MAS)13C nuclear magnetic resonance(NMR),which have revealed the presence of urethane functions.The interpretation of the results has shown a larger number of species than when tannins were used and has indicated the presence of two types of bonds in the new molecules formed:ionic and covalent bonds.

Development and Characterization of Eco-Friendly Non-Isocyanate Urethane Monomer from Jatropha curcas Oil for Wood Composite Applications

The aim of this research work was to evaluate the potential of using renewable natural feedstock,i.e.,Jatropha curcas oil(JCO)for the synthesis of non-isocyanate polyurethane(NIPU)resin for wood composite applications.Commercial polyurethane(PU)is synthesized through a polycondensation reaction between isocyanate and poly-ol.However,utilizing toxic and unsustainable isocyanates for obtaining PU could contribute to negative impacts on the environment and human health.Therefore,the development of PU from eco-friendly and sustainable resources without the isocyanate route is required.In this work,tetra-n-butyl ammonium bromide was used as the activator to open the epoxy ring with 3-Aminopropyltriethoxisylane as a catalyst to yield urethane of JCO(UJCO).The UJCO were characterized by Fourier Transform Infra-Red spectroscopy(FTIR)and their oxirane,and hydroxyl values were measured.The result showed that a decrease in oxirane value was found while the hydroxyl value was increased during the time,confirming that the urethane group was formed.The presence of functional groups in FTIR spectra at wave numbers 1732.08,1562.34,and 3348.42 cm^(−1) indicates the functional groups of C=O(urethane carbonyl),–NH,and–OH,respectively confirmed this finding.The potential applications of NIPU in the wood composite were also outlined.

Effects of urethane on the response properties of visual cortical neurons in young adult and old cats

Previous studies have shown that visual cortical neurons in old mammals exhibit higher spontaneous activity,higher responsiveness to visual stimuli,and lower selectivity for stimulus orientations and motion directions than did neurons in young adult counterparts.However,whether the responsive difference in cortical neurons between young and old animals resulted from different effects induced by anesthetics has remained unclear.To clarify this issue,we recorded the response properties of individual neurons in the primary visual cortex of old and young adult cats while systematically varying the anesthesia level of urethane,a widely used anesthetic in physiology experiments.Our results showed that cumulatively administrating 50 mg and 100 mg of urethane upon the minimal level of urethane required to anesthetize an old or young adult cat did not significantly alter the degree of neuronal response selectivity for stimulus orientations and motion directions nor significantly change the visually-driven response and spontaneous activity of neurons in old and young adult cats.Cumulatively administrating 150 mg of urethane decreased neuronal responsiveness similarly in both age groups.Therefore,urethane appears to exert similar effects on neuronal response properties of old and young adult animals.

Anti-fouling ultrafiltration membrane prepared from polysulfone-graft-methyl acrylate copolymers by UV-induced grafting method

Membrane fouling is one of the most important challenges faced in membrane ultrafiltration operations. The copolymers of polysulfone-graft-methyl acrylate were synthesized by homogeneous photo-initiated graft copolymerization. The variables affecting the degree of grafting, such as the time of UV （Ultraviolet-visible） irradiation and the concentrations of the methyl acrylate and photoinitiator, were investigated. The graft copolymer membranes were prepared by the phase inversion method. The chemical and morphological changes were characterized by attenuated total reflection-Fourier transform infrared spectroscopy （ATR/FT-IR）, scanning electron microscopy, and water contact angles measurements. Results revealed that methyl acrylate groups were present on the membranes and the graft degree of methyl acrylate had remarkable effect on the performance of membranes. Pure water contact angle on the membrane surface decreases with the increase of methyl acrylate graft degree, which indicated that the hydrophilicity of graft copolymer membranes was improved. The permeation fluxes of pure water and bovine serum albumin solution were measured to evaluate the antifouling property of graft copolymer membranes, the results of which have shown an enhancement of antifouling property for graft copolymer membranes.