Filtered cathodic vacuum arc(FCVA)deposition is regarded as an important technique for the synthesis of tetrahedral amorphous carbon(ta-C)films due to its high ionization rate,high deposition rate and effective filtra...Filtered cathodic vacuum arc(FCVA)deposition is regarded as an important technique for the synthesis of tetrahedral amorphous carbon(ta-C)films due to its high ionization rate,high deposition rate and effective filtration of macroparticles.Probing the plasma characteristics of arc discharge contributes to understanding the deposition mechanism of ta-C films on a microscopic level.This work focuses on the plasma diagnosis of an FCVA discharge using a Langmuir dualprobe system with a discrete Fourier transform smoothing method.During the ta-C film deposition,the arc current of graphite cathodes and deposition pressure vary from 30 to 90 A and from 0.3 to 0.9 Pa,respectively.The plasma density increases with arc current but decreases with pressure.The carbon plasma density generated by the arc discharge is around the order of10^(10)cm^(-3).The electron temperature varies in the range of 2-3.5 eV.As the number of cathodic arc sources and the current of the focused magnetic coil increase,the plasma density increases.The ratio of the intensity of the D-Raman peak and G-Raman peak(I_(D)/I_(G))of the ta-C films increases with increasing plasma density,resulting in a decrease in film hardness.It is indicated that the mechanical properties of ta-C films depend not only on the ion energy but also on the carbon plasma density.展开更多
For the crystalline temperature of BaSnO_(3)(BTO)was above 650℃,the transparent conductive BTO-based films were always deposited above this temperature on epitaxy substrates by pulsed laser deposition or molecular be...For the crystalline temperature of BaSnO_(3)(BTO)was above 650℃,the transparent conductive BTO-based films were always deposited above this temperature on epitaxy substrates by pulsed laser deposition or molecular beam epitaxy till now which limited there application in low temperature device process.In the article,the microstructure,optical and electrical of BTO and In_(2)O_(3) mixed transparent conductive BaInSnO_(x)(BITO)film deposited by filtered cathodic vacuum arc technique(FCVA)on glass substrate at room temperature were firstly reported.The BITO film with thickness of 300 nm had mainly In_(2)O_(3) polycrystalline phase,and minor polycrystalline BTO phase with(001),(011),(111),(002),(222)crystal faces which were first deposited at room temperature on amorphous glass.The transmittance was 70%–80%in the visible light region with linear refractive index of 1.94 and extinction coefficient of 0.004 at 550-nm wavelength.The basic optical properties included the real and imaginary parts,high frequency dielectric constants,the absorption coefficient,the Urbach energy,the indirect and direct band gaps,the oscillator and dispersion energies,the static refractive index and dielectric constant,the average oscillator wavelength,oscillator length strength,the linear and the third-order nonlinear optical susceptibilities,and the nonlinear refractive index were all calculated.The film was the n-type conductor with sheet resistance of 704.7Ω/□,resistivity of 0.02Ω⋅cm,mobility of 18.9 cm2/V⋅s,and carrier electron concentration of 1.6×10^(19) cm^(−3) at room temperature.The results suggested that the BITO film deposited by FCVA had potential application in transparent conductive films-based low temperature device process.展开更多
This paper introduces working principle and technical features of vacuum filter in emulsion system for tandem cold strip mill.Based on specific cases,this paper analyses and assesses the effect before and after using ...This paper introduces working principle and technical features of vacuum filter in emulsion system for tandem cold strip mill.Based on specific cases,this paper analyses and assesses the effect before and after using the emulsion system with the usage of the vacuum filter for strip mill.Compare with the effect when using the first generation vacuum filter,the emulsion quality is improved significantly by using the second generation vacuum filter,which at the same time ensures steady operation of the rolling mill and surface quality of the mill products. As a result,investment and running costs are lowered,emissions of the waste emulsion are reduced,waste water treatment costs are reduced and so as the environmental pollution.It can be seen the second generation vacuum filter has obvious economic and environmental benefits.Therefor,it suggests that the filter should be used widely in the field of automotive,environmental protection rolling steel and nonferrous metals.展开更多
Diamond like carbon thin film is successfully deposited on silicon, titanium and stainless steel substrate at low temperature in a filtered vacuum arc deposition system. Arc discharges are established on a graphite ...Diamond like carbon thin film is successfully deposited on silicon, titanium and stainless steel substrate at low temperature in a filtered vacuum arc deposition system. Arc discharges are established on a graphite cathode in the system with a toroidal macroparticle filter. A cathode activating magnetic field and a filtered magnetic field to collimate the plasma beam are applied. Ion current convected by the plasma beam is measured with a negatively biased probe. It is shown that the magnetic field of the coils located on the plasma duct has a strong influence on cathode spot behavior. Orthogonally the designed experiments are carried out to optimize the deposition parameters of arc stability. Finally, the diamond like carbon thin films are studied by scanning electron microscope (SEM) and Raman spectrum.展开更多
Diamond like carbon (DLC) films was grown successfully on silicon, titanium and high speed steel (HSS) substrate at low temperature in a filtered vacuum arc deposition system. Arc discharges were established on a gra...Diamond like carbon (DLC) films was grown successfully on silicon, titanium and high speed steel (HSS) substrate at low temperature in a filtered vacuum arc deposition system. Arc discharges were established on a graphite cathode in this home built system with a toridal macroparticles filter. Ion current convected by the plasma beam was measured with a negatively biased probe. It was shown that the magnetic field of the coils located on the plasma duct has a strong influence on ion current. Scanning electron microscope (SEM), atomic force microscope (AFM) and Raman spectrum are used to study the DLC films. Tribological behaviors of the deposited film are also studied.展开更多
基金supported by the National Key Research and Development Program of China(No.2016YFB0101206)the Science and Technology Program of Wuhu(No.2021hg11)the Natural Science Foundation of the Anhui Higher Education in Institutions of China(No.2022AH050300)。
文摘Filtered cathodic vacuum arc(FCVA)deposition is regarded as an important technique for the synthesis of tetrahedral amorphous carbon(ta-C)films due to its high ionization rate,high deposition rate and effective filtration of macroparticles.Probing the plasma characteristics of arc discharge contributes to understanding the deposition mechanism of ta-C films on a microscopic level.This work focuses on the plasma diagnosis of an FCVA discharge using a Langmuir dualprobe system with a discrete Fourier transform smoothing method.During the ta-C film deposition,the arc current of graphite cathodes and deposition pressure vary from 30 to 90 A and from 0.3 to 0.9 Pa,respectively.The plasma density increases with arc current but decreases with pressure.The carbon plasma density generated by the arc discharge is around the order of10^(10)cm^(-3).The electron temperature varies in the range of 2-3.5 eV.As the number of cathodic arc sources and the current of the focused magnetic coil increase,the plasma density increases.The ratio of the intensity of the D-Raman peak and G-Raman peak(I_(D)/I_(G))of the ta-C films increases with increasing plasma density,resulting in a decrease in film hardness.It is indicated that the mechanical properties of ta-C films depend not only on the ion energy but also on the carbon plasma density.
基金Project supported by the Enterprise Science and Technology Correspondent for Guangdong Province,China (Grant No.GDKTP2021015200)。
文摘For the crystalline temperature of BaSnO_(3)(BTO)was above 650℃,the transparent conductive BTO-based films were always deposited above this temperature on epitaxy substrates by pulsed laser deposition or molecular beam epitaxy till now which limited there application in low temperature device process.In the article,the microstructure,optical and electrical of BTO and In_(2)O_(3) mixed transparent conductive BaInSnO_(x)(BITO)film deposited by filtered cathodic vacuum arc technique(FCVA)on glass substrate at room temperature were firstly reported.The BITO film with thickness of 300 nm had mainly In_(2)O_(3) polycrystalline phase,and minor polycrystalline BTO phase with(001),(011),(111),(002),(222)crystal faces which were first deposited at room temperature on amorphous glass.The transmittance was 70%–80%in the visible light region with linear refractive index of 1.94 and extinction coefficient of 0.004 at 550-nm wavelength.The basic optical properties included the real and imaginary parts,high frequency dielectric constants,the absorption coefficient,the Urbach energy,the indirect and direct band gaps,the oscillator and dispersion energies,the static refractive index and dielectric constant,the average oscillator wavelength,oscillator length strength,the linear and the third-order nonlinear optical susceptibilities,and the nonlinear refractive index were all calculated.The film was the n-type conductor with sheet resistance of 704.7Ω/□,resistivity of 0.02Ω⋅cm,mobility of 18.9 cm2/V⋅s,and carrier electron concentration of 1.6×10^(19) cm^(−3) at room temperature.The results suggested that the BITO film deposited by FCVA had potential application in transparent conductive films-based low temperature device process.
文摘This paper introduces working principle and technical features of vacuum filter in emulsion system for tandem cold strip mill.Based on specific cases,this paper analyses and assesses the effect before and after using the emulsion system with the usage of the vacuum filter for strip mill.Compare with the effect when using the first generation vacuum filter,the emulsion quality is improved significantly by using the second generation vacuum filter,which at the same time ensures steady operation of the rolling mill and surface quality of the mill products. As a result,investment and running costs are lowered,emissions of the waste emulsion are reduced,waste water treatment costs are reduced and so as the environmental pollution.It can be seen the second generation vacuum filter has obvious economic and environmental benefits.Therefor,it suggests that the filter should be used widely in the field of automotive,environmental protection rolling steel and nonferrous metals.
文摘Diamond like carbon thin film is successfully deposited on silicon, titanium and stainless steel substrate at low temperature in a filtered vacuum arc deposition system. Arc discharges are established on a graphite cathode in the system with a toroidal macroparticle filter. A cathode activating magnetic field and a filtered magnetic field to collimate the plasma beam are applied. Ion current convected by the plasma beam is measured with a negatively biased probe. It is shown that the magnetic field of the coils located on the plasma duct has a strong influence on cathode spot behavior. Orthogonally the designed experiments are carried out to optimize the deposition parameters of arc stability. Finally, the diamond like carbon thin films are studied by scanning electron microscope (SEM) and Raman spectrum.
文摘Diamond like carbon (DLC) films was grown successfully on silicon, titanium and high speed steel (HSS) substrate at low temperature in a filtered vacuum arc deposition system. Arc discharges were established on a graphite cathode in this home built system with a toridal macroparticles filter. Ion current convected by the plasma beam was measured with a negatively biased probe. It was shown that the magnetic field of the coils located on the plasma duct has a strong influence on ion current. Scanning electron microscope (SEM), atomic force microscope (AFM) and Raman spectrum are used to study the DLC films. Tribological behaviors of the deposited film are also studied.
