Influence of Asymmetric Monotonic Hot Rolling on Microstructures and Mechanical Property of Microalloyed Steel

For refining grain and obtaining excellent properties, the experiments of asymmetric and symmetric monotonic hot rolling were carried out to investigate the role of shear strain on the microstructures and mechanical properties of V-microalloyed steel. The study demonstrates that the gradient ferrite distribution and dispersive pearlite through the sheet thickness are observed in asymmetric rolled specimen, and the homogeneous microstructure with ferrite and large pearlite is found in symmetric rolled specimen. The average grain size in asymmetric rolled specimen is smaller than the one in symmetric rolled specimen. The styles of precipitate morphology in asymmetric rolled specimen are random precipitate and obvious interphase precipitate, while the ones in symmetric rolled specimen are random precipitate and unobvious interphase precipitate. The additional shear strain results in the microstructure difference between asymmetric rolled specimen and symmetric rolled specimen. The impact energy of asymmetric rolled specimen, 58 J, is more than the one of symmetric rolled specimen, 48 J. Both deflection-energy curve and fracture morphology show that the fracture style of asymmetric rolled specimen is ductile, and the ones of symmetric rolled specimen are brittle and ductile.

Effect of Vanadium Microalloying on the HAZ Microstructure and Properties of Low Carbon Steels

Four Steels,C-Mn-0.05V,C-Mn-0.11V,C-Mn-0.03Nb and C-Mn were subjected to heat treatment to simulate the microstructure of a coarse grained heat affected zone (CGHAZ) and an intercritically reheated coarse grained heat affected zone (ICCGHAZ).This involved reheating to 1350°C,rapid cooling (Δt 8/5 =24s) to room temperature and then reheating to either 750°C or 800°C.The toughness of the HAZs was assessed using both Charpy and CTOD tests.Microstructural features were characterised by optical,scanning` and transmission electron microscopy.Fractographic examinations of the Charpy and CTOD specimens were carried out to understand the micromechanism of fracture under different microstructural and test conditions.The CGHAZ toughness was similar for the steels except that Steel C-Mn-0.05V had a slightly lower ITT compared to the others.The toughness deteriorated in the ICCGHAZ for all the steels,again Steel C-Mn-0.05V had a superior toughness compared to the other three steels in both ICCGHAZ conditions.Raising the level of vanadium to 0.11% caused a decrease in ICCGHAZ toughness.Steel C-Mn-Nb exhibited a greater degradation of impact toughness after the intercritical cycles.The presence of M-A constituents was the dominant factor in determining the toughness of the ICCGHAZs.The size and area fraction of the M-A constituents were the smallest in Steel C-Mn-0.05V.Increasing vanadium level to 0.11% resulted in a greater area fraction of the M-A constituents,larger average and maximum sizes of M-A particles,and significantly more fields containing the M-A.The addition of 0.031% Nb produced the largest M-A particles and the greatest area fraction for the steels tested.

Effect of Carbon on Dynamic Recrystallization Behavior of Vanadium Microalloy Steels

The hot working behavior especially dynamic recrystallization of low-carbon and medium-carbon vanadium microalloy steels has been studied by performing isothermally compression tests and Avrami analysis.The Avrami plots of the two experiment steels have been constructed based on flow stress curves following a new approach (Jonas,et al.Acta Mater.,2009,57(2):2748-2756;Wu et al,Acta Metall.Sin.,2010,46(7):838-843).It is experimentally found that the carbon effect on dynamic recrystallization is opposite to each other in lower and higher strain ranges:Carbon causes a softening effect at low strain rates (0.01,0.1,and 1.0 s-1),and a hardening effect at high strain rates (10.0 and 30.0 s-1).Correspondingly,carbon promotes the dynamic recrystallization at low strain rates and retards the dynamic recrystallization at high strain rates in the experimental steels.The phenomenon is then tentatively explained based on the possible mechanisms of dynamic process at different strain rates.

Effect of Cooling Rate and Vanadium Content on the Microstructure and Hardness of Medium Carbon Forging Steel

This paper reports the effect of cooling rate on the microstructure and hardness of a kind of medium carbon steel microalloyed with two levels of V content （0.15% and 0.28%） after hot deformation by using single compression tests on a Gleeble-3800 thermal simulator. The results show that cooling rate has a significant effect on the microstructure and hardness of the tested steels. Both the fraction of pearlite and hardness increase with increasing cooling rate, whereas a further increase of the cooling rate above a critical value promotes the formation of acicular ferrite （AF）, and thus leads to a decrease of hardness mainly owing to the decrease of pearlite fraction and replacing it by AF and the less effective precipita- tion strengthening. Increasing V content results in a significant increase of hardness, and this tendency enhances with increasing cooling rate until the formation of AF. Furthermore, increasing V content also significantly enhances the formation of AF structure at a lower cooling rate. The results also suggest that by controlling microstructure, especially the precipitation of fine V（C,N） particles through adjusting post- forging cooling, the strengthening and gradient function in one hot-forging part could be obtained.

Influence of Vanadium on Fracture Splitting Property of Medium Carbon Steel

The fracture splitting property of medium carbon steel 37MnSiS microalloyed with V up to 0. 45% was investigated by using simulated fracture splitting test,for the development of new crackable medium carbon steel to manufacture high performance connecting rod. Conventional high carbon steel C70S6 was used for comparison. The results show that the volume fraction of both ferrite and V-rich M（ C,N） particles increases,and the pearlite interlamellar spacing decreases with increasing V content,which in turn results in gradual increase of strength and decrease of ductility and impact energy. The fracture splitting property of the tested steel could be improved significantly due to the increase of V content mainly through the precipitation hardening mechanism of fine M（ C,N） precipitates. The fraction of brittle cleavage fracture in the crack initiation area increases noticeably with increasing V content and full brittle cleavage fracture surface could be obtained when V content was increased to 0. 45%. It is concluded that medium carbon steel with V content higher than about 0. 28% possesses not only comparable or even higher mechanical properties with those of conventional steel C70S6,but also excellent fracture splitting property,and therefore,is more suitable to fabricate high performance fracture splitting connecting rod.

Enhanced strength and toughness of high nitrogen stainless bearing steel by controlling interstitial partitioning via V-microalloying

High-nitrogen stainless bearing steel(HNSBS)with ultra-high tensile strength(∼2403 MPa)and good toughness(∼80.0 J)was obtained by V-microalloying,overcoming the strength-toughness trade-off of conventional V-free HNSBS.In this work,since V-microalloying facilitated the enrichment of interstitial atoms(C and N)in precipitates,the content of interstitial atoms in the matrix was reduced accordingly(i.e.,interstitial partitioning).On the one hand,V-microalloying reduced the substantial intergranular precipitates and transformed the precipitates from M_(23)C_(6)+M_(2)N into V-containing M_(23)C_(6)+M_(2)N+MN with multi-scale particle sizes,causing a coupling strengthening effect,which contributed to the toughness and additional strength increase.On the other hand,V-microalloying controlled interstitial partitioning,effectively refined coarse retained austenite(RA),increased the fraction of dislocation martensite,and reduced the fraction of twin martensite.The more film-like RA and dislocation martensite with high dislocation density coordinated plastic deformation and prevented crack propagation,thus obviously enhancing the strength and toughness of 0.2 V steel.This study provides a new route to develop high-performance HNSBS for aerospace applications.

Warm Forged Medium Carbon V Steel

Nowadays there is a continuous demand,particularly from the automotive industry,for cheaper,lighter and more reliable components.It is not surprising then that steel research has been focused during the last decades in new qualities and processes.This paper is dealing with the use of vanadium microalloyed steels on one of those new processes,warm forging.For its low precipitation temperature and its recognised ability to strengthen steel microstructures via austenite grain growth control,precipitation hardening and interference of the static recrystallization process,vanadium in microalloyed steels seem to be an appropriate candidate for warm forging.