Thermodynamic simulation of stepwise precipitation of NH_4VO_(3)and NaHCO_(3)from carbonating Na_(3)VO_(4)solution

Thermodynamic simulation was conducted to design a new process of stepwise precipitating NH_4VO_(3)and NaHCO_(3)from regulating the CO_(2)carbonation of Na_(3)VO_(4)solution.Firstly,a new V(V)speciation model for the aqueous solution containing vanadate and carbonate is established by using the Bromley-Zemaitis activity coefficient model.Subsequently,thermodynamic equilibrium calculations are conducted to clarify the behavior of vanadium,carbon,sodium,and impurity species in atmospheric or high-pressure carbonation.To ensure the purity and recovery of vanadium products,Na_(3)VO_(4)solution is initially carbonated to the pH of 9.3-9.4,followed by precipitating NH_4VO_(3)by adding(NH_4)_(2)CO_(3).After vanadium precipitation,the solution is deeply carbonated to the final pH of 7.3-7.5 to precipitate NaHCO_(3),and the remaining solution is recycled to dissolve Na_(3)VO_(4)crystals.Finally,verification experiments demonstrate that 99.1%of vanadium and 91.4%of sodium in the solution are recovered in the form of NH_4VO_(3)and NaHCO_(3),respectively.

Cyclic metallurgical process for extracting V and Cr from vanadium slag: Part Ⅱ. Separation and recovery of Cr from vanadium precipitated solution

Cyclic metallurgical process for separation and recovery of Cr from vanadium precipitated solution by precipitation with PbCO_(3)and leaching with Na_(2)CO_(3)was investigated.The concentration of Cr residue in the solution decreases from 2.360 to 0.001 g/L by adding PbCO_(3)into vanadium precipitated solution according to Pb/Cr molar ratio of 2.5,adjusting the pH to 3.0 and stirring for 180 min at 30℃.Then,the precipitates were leached with hot Na_(2)CO_(3)solution to obtain leaching solution containing Na_(2)CrO_(4)and leaching residue containing PbCO_(3).The leaching efficiency of Cr reaches 96.43%by adding the precipitates into 0.5 mol/L Na_(2)CO_(3)solution with the mass ratio of liquid to solid(L/S)of 10:1 mL/g and stirring for 60 min under pH 9.5 at 70℃.After filtration,leaching residue is reused in Cr precipitation and leaching solution is used to circularly leach the Cr precipitates until Na_(2)CrO_(4)approaches the saturation.Finally,the product of Na_(2)CrO_(4)·4H_(2)O is obtained by evaporation and crystallization of leaching solution.

Cyclic metallurgical process for extracting Ⅴ and Cr from vanadium slag: Part Ⅰ. Separation and recovery of Ⅴ from chromium-containing vanadate solution

The separation and recovery of V from chromium-containing vanadate solution were investigated by a cyclic metallurgical process including selective precipitation of vanadium,vanadium leaching and preparation of vanadium pentoxide.By adding Ca(OH)_(2) and ball milling,not only the V in the solution can be selectively precipitated,but also the leaching kinetics of the precipitate is significantly improved.The precipitation efficiency of V is 99.59%by adding Ca(OH)_(2) according to Ca/V molar ratio of 1.75:1 into chromium-containing vanadate solution and ball milling for 60 min at room temperature,while the content of Cr in the precipitate is 0.04%.The leaching rate of V reaches 99.35%by adding NaHCO_(3) into water according to NaHCO_(3)/V molar ratio of 2.74:1 to leach V from the precipitate with L/S ratio of 4:1 mL/g and stirring for 60 min at room temperature.The crystals of NH_(4)VO_(3) are obtained by adjusting the leaching solution pH to be 8.0 with CO2 and then adding NH_(4)HCO_(3) according to NH_(4)HCO_(3)/NaVO_(3) molar ratio of 1:1 and stirring for 8 h at room temperature.After filtration,the crystallized solution containing ammonia is reused to leach the precipitate of calcium vanadates,and the leaching efficiency of V is>99%after stirring for 1 h at room temperature.Finally,the product of V_(2)O_(5) with purity of 99.6%is obtained by calcining the crystals at 560℃ for 2 h.

Influence of Vanadium on Fracture Splitting Property of Medium Carbon Steel

The fracture splitting property of medium carbon steel 37MnSiS microalloyed with V up to 0. 45% was investigated by using simulated fracture splitting test,for the development of new crackable medium carbon steel to manufacture high performance connecting rod. Conventional high carbon steel C70S6 was used for comparison. The results show that the volume fraction of both ferrite and V-rich M（ C,N） particles increases,and the pearlite interlamellar spacing decreases with increasing V content,which in turn results in gradual increase of strength and decrease of ductility and impact energy. The fracture splitting property of the tested steel could be improved significantly due to the increase of V content mainly through the precipitation hardening mechanism of fine M（ C,N） precipitates. The fraction of brittle cleavage fracture in the crack initiation area increases noticeably with increasing V content and full brittle cleavage fracture surface could be obtained when V content was increased to 0. 45%. It is concluded that medium carbon steel with V content higher than about 0. 28% possesses not only comparable or even higher mechanical properties with those of conventional steel C70S6,but also excellent fracture splitting property,and therefore,is more suitable to fabricate high performance fracture splitting connecting rod.

Influence of V(C,N) Precipitates on Microstructure and Mechanical Properties of Continuous Cooled C-Mn-V

The effect of chemical composition and processing parameters on the formation of acicular ferrite and/or bainite has been investigated.In particular,this paper deals with the influence that N through its combination with V,as V(C,N) precipitates,has on the decomposition of austenite.Likewise,the intragranular nucleation potency of V(C,N) precipitates is analyzed through the continuous cooling transformation diagrams (CCT) of two C-Mn-V steels with different contents of N.Results reported in this work allow us to conclude that acicular ferrite can only be achieved alloying with vanadium and nitrogen,meanwhile bainite is promoted in steels with a low level of nitrogen.It is concluded that higher strength values are obtained in acicular ferrite than in bainitic steel but a similar brittle-ductile transition temperature (BDT),and lower values of impact absorbed energy (KV) has been recorded in nitrogen-rich steel.

Effect of Alloying Method on Microstructure and Wear Resistance of Fe-Cr-V-B Based Alloy

The microstructure and wear behavior of Fe-Cr-V-B based alloy was investigated.Each of the specimens was characterized by metallographic techniques and hardness test.Phase analysis of alloy was performed by X-ray diffraction（XRD）,scanning electron microscopy（SEM）and energy dispersive spectroscopy（EDS）.The results showed that the microstructure of Fe-Cr-V-B based as-cast alloy containing 8.6mass% V was composed ofα-（Fe,Cr）solid solution,VC carbides,and V_3B_4 borides,whereas the as-cast alloy containing 24.8mass% Cr was composed ofα-（Fe,Cr）solid solution and V_3B_4borides;the eutectic V_3B_4 borides mainly comprise M2B-type borides（M presents Fe and Cr）.The existence of a large amount of V atoms affects the growth pattern of eutectic borides,which mainly display rod-like and grainy structure.The wear behavior of the experimental alloy has been investigated using pin-on-disk type friction and wear apparatus.The comparison of experimental results indicated that the relative wear resistance of the alloy containing 8.6mass% V after destabilization heat treatment in a conventional furnace at 1 373 K for 2hwas about six times higher than that of the high chromium（19mass%）cast iron.