Bioleaching of vanadium from stone coal vanadium ore by Bacillus mucilaginosus:Influencing factors and mechanism

Vanadium and its derivatives are used in various industries,including steel,metallurgy,pharmaceuticals,and aerospace engineering.Although China has massive reserves of stone coal resources,these resources have low grades.Therefore,the effective extraction and recovery of metallic vanadium from stone coal is an important way to realize the efficient resource utilization of stone coal vanadium ore.Herein,Bacillus mucilaginosus was selected as the leaching strain.The vanadium leaching rate reached 35.5%after 20 d of bioleaching under optimal operating conditions.The cumulative vanadium leaching rate in the contact group reached 35.5%,which was higher than that in the noncontact group(9.3%).The metabolites of B.mucilaginosus,such as oxalic,tartaric,citric,and malic acids,dominated in bioleaching,accounting for 73.8%of the vanadium leaching rate.Interestingly,during leaching,the presence of stone coal stimulated the expression of carbonic anhydrase in bacterial cells,and enzyme activity increased by 1.335-1.905 U.Enzyme activity positively promoted the production of metabolite organic acids,and total organic acid content increased by 39.31 mg·L^(-1),resulting in a reduction of 2.51 in the pH of the leaching system with stone coal.This effect favored the leaching of vanadium from stone coal.Atomic force microscopy illustrated that bacterial leaching exacerbated corrosion on the surface of stone coal beyond 10 nm.Our study provides a clear and promising strategy for exploring the bioleaching mechanism from the perspective of microbial enzyme activity and metabolites.

Infiltration behavior of sintering liquid on nuclei ores during low-titanium ore sintering process

Sinter strength is dependent not only on the self-intensity of the residual rude and bonding phase but also on the bonding degree between them. The infiltration behavior of sintering liquid on nuclei ores influences the bonding degree, which ultimately determines the sinter strength. Infiltration tests were conducted using micro-sinter equipment. The infiltration area index of original liquid（IAO）, infiltration volume index of secondary liquid（IVS）, and sinter body bonding strength（SBS） were proposed to study the melt infiltration behavior. The results show that the IVS first increases and then decreases with increasing TiO2 content in adhering fines, whereas the IAO exhibits the opposite behavior. Compared with the original liquid, the secondary liquid shows lower porosity, smaller pores, and more uniform distribution. The SBS increases first and then decreases with increasing IAO and TiO2 content, and reaches a maximum when the IAO and TiO2 contents are approximately 0.5 and 2.0wt%, respectively. The SBS first increases and then tends to be stable with increasing IVS. The TiO2 content is suggested to be controlled to approximately 2.0wt% in low-titanium ore sintering.

Water quality,natural chemical weathering and ecological risk assessment of the contaminated area of vanadium ore in Yinhua River,China:Evidence from major ions and trace elements

There are abundant vanadium ores in the Cambrian strata in southern Shaanxi,China.Many years of mining activities and surface leaching have polluted the surface water to a certain extent,but the researches on the water quality characteristics and pollution degree are relatively weak.This contribution was organized to investigate the surface water quality by general parameters,including TDS,Eh,pH,DO,TOC,COD,and EC,in the vanadium ore belt(Yinhua River basin).Major ions were determined to detect the water type and natural chemical weathering,while trace elements were used to illustrate their geochemical characteristics and ecological risk assessment of heavy metals.The study found that the surface water was weakly alkaline and mainly dominated from normal to pool grade.The particle size with1000–10,000 nm of suspended particles was the main carrier of organic matter.The concentration of HCO_(3)^(-)and SO_(4)^(2-)in the anions and Ca^(2+)and Mg^(2+)ions in the cations were relatively high,and the water type was Ca-Mg-HCO_(3)-SO_(4) type.Rock weathering had a great influence on surface water,and the weathering products were mainly silicate and carbonate.Compared with the Type river,the contents of V elements showed an obvious positive anomaly,which may be affected by mining activities of vanadium ore and the annual leaching of the tailings pond.As and Cd in the surface water was polluted seriously.The integrated pollution index suggested that the surface water pollution was serious,and the main stream was more serious with the increasing tailings ponds.

Effects of the mineral phase and valence of vanadium on vanadium extraction from stone coal

The influence of roasting on the leaching rate and valence of vanadium was evaluated during vanadium extraction from stone coal. Vanadium in stone coal is hard to be leached and the leaching rate is less than 10% when the raw ore is leached by 4 moUL H2SO4 at 90℃ for 2 h. After the sample is roasted at 900℃ for 2 h, the leaching rate of vanadium reaches the maximum, and more than 70% of vanadium can be leached. The crystal of vanadium-bearing mica minerals decomposes and the Content of V（V） increases with the rise of roasting temperature from 600 to 900℃, therefore the leaching rate of vanadium increases significantly with the decomposition of the mica minerals. Some new phases, anorthite for example, form when the roasting temperature reaches 1000℃. A part of vanadium may be enwrapped in the sintered materials and newly formed phases, which may impede the oxidation of low valent vanadium and make the leaching rate of vanadium drop dramatically. The leaching rate of vanadium is not only determined by the valence state of vanadium but also controlled by the decomposition of vanadium-bearing minerals and the existence state of vanadium to a large extent.

Sintering behaviors and consolidation mechanism of high-chromium vanadium and titanium magnetite fines

To achieve high efficiency utilization of high-chromium vanadium-titanium magnetite （V-Ti-Cr） fines, an investigation of V Ti42r fines was conducted using a sinter pot. The chemical composition, particle parameters, and granulation of V-Ti-Cr mixtures were analyzed, and the effects of sintering parameters on the sintering behaviors were investigated. The results indicated that the optimum quicklime dosage, mixture moisture, wetting time, and granulation time for V-Ti-Cr fines are 5wt%, 7.5wt%, 10 min, and 5-8 min, respectively. Meanwhile, the vertical sintering speed, yield, tumbler strength, and productivity gains were shown to be 21.28 mm/min, 60.50wt% , 58.26wt%, and 1.36 t·m^-2·h^-1, respectively. Furthermore, the consolidation mechanism of V-Ti-Cr fines was clarified, revealing that the consolidation of a V-Ti-Cr sinter requires an approximately 14vo1% calcium ferrite liquid-state, an approximately 15vo1% silicate liq- uid-state, a solid-state reaction, and the recrystallization of magnetite. Compared to an ordinary sinter, calcium ferrite content in a V-Ti-Cr sinter is lower, while the perovskite content is higher, possibly resulting in unsatisfactory sinter outcomes.

Perspectives of Development of “Black-Shale” Type Ore on the Territory of the Republic of Uzbekistan

Currently there have been formed industrial uranium deposits in Kyzylkum province that refer to three types of formations—exogenetic uranium formation in the sediments of Mesozoic-Cenozoic cover,endogenic molybdenum-uranium formation and polygenic molybdenum-uranium-vanadium formation in carbon-siliceous shale formations ("black-shale"type).Carbon-siliceous shales are

Laboratory Obtaining of Ferroalloy after Reduction of Oxides from Waste Product and Natural Resource

The Obrochishte deposit located in the Republic of Bulgaria has considerable reserves of relatively poor carbonate manganese ore. At the same time, in the country there are operative outputs for the production of sulphuric acid where vanadium catalyst is deactivated and discharged, polluting the environment. The utilization of these materials requires their consolidation to proper sizes with regard to the next processing, as the most suitable method for joint consolidation is agglomeration. The present work explores the preliminary calculations for obtaining agglomerate and obtaining an alloy with high and low carbon content, through carbothermic and aluminothermic agglomerate reduction.

Influence of Coating MgO on Sticking and Functional Mechanism during Fluidized Bed Reduction of Vanadium Titano-magnetite

The vanadium titano-magnetite （VTM） iron ore fines of 110--150/xm in diameter were reduced in a trans- parent quartz fluidized bed by 70 %CO-30 % H2 （volume fraction） mixtures. MgO powders served as coating agent to solve sticking problem. Two coating methods were introduced in this experiment： high temperature injection method and briquetting→oxidizing roast→crushing method. According to the experimental results, the minimum effective coating amount of MgO was 0. 1 mass%. The metallization ratio （MR） of the product rose from around 58% to above 90% with the above treatments. To investigate the sticking mechanism of fine ore, the morphology evolution was in- vestigated. Instead of iron whiskers, an interlaced fibrous porous surface formed. The ulvospinel （2FeO ： TiO2 ） in VTM is more difficult to be reduced than FeO according to thermodynamic calculation. XRD results showed that MgO diffused into Fe203 lattice before forming pleonaste （MgO · Fe2O3 ） during oxidizing roast at 1273 K. The melting point of the pleonaste is 1986 K and that made contribution to prevent the sticking problem.