Characteristic Analysis and Experimental Study of a Hybrid Permanent Magnet Variable Flux Memory Motor

提出一种混合永磁可变磁通记忆电机，研究了永磁体不同磁化状态下的静态特性。基于有限元法，对施加不同去磁电流时的电机磁场分布进行了分析，并观察永磁体内的磁密变化，计算了不同永磁磁化状态下的气隙磁密、永磁磁链、反电动势及每极气隙磁通等电机主要参数。制作一台样机，并进行实验研究，实验结果与有限元计算结果吻合较好。研究表明，永磁体的充磁比去磁要困难，当磁化电流为2倍的定子额定电流时，能将磁体去磁90％，而仅能充磁到饱和时的30％：与基本结构记忆电机相比，该混合永磁记忆电机具有更高的气隙磁密。该类电机在宽调速驱动系统中具有应用前景。

An Improved Stator Flux Observation Method of Permanent Magnet Synchronous Motor

The stator flux and electromagnetic torque observation is the basis of direct torque controlled permanent magnet synchronous motor( PMSM) drive system. However,the traditional stator flux observer based on voltage model is affected by integral initial values and integral drift,that based on current model is affected by the parameters of PMSM,so a new stator flux observation method is proposed based on an improved secondorder generalized integrator( SOGI). Compared to the stator flux observation method based on the conventional SOGI,the proposed method can not only overcome the influence of integral initial values and integral drift,but also completely eliminate the DC offset's influence. Therefore,the observation accuracy of stator flux is further improved. The simulation and experimental results both show that the proposed method has a higher stator flux and electromagnetic torque observation precision.

Model predictive flux control of permanent magnet synchronous motor driven by three-level inverter based on fine-division strategy

Aiming at the difficulty of setting the weight coefficient in the value function of model predictive torque control(MPTC)for permanent magnet synchronous motor(PMSM)driven by three-level inverter,a fine-division model predictive flux control(MPFC)method is proposed.First,establish a mathematical model between the motor torque and the stator flux linkage according to the mathematical equations of PMSM.Thus,the control of the motor torque and stator flux linkage in the MPTC is transformed into the control of a single stator flux linkage vector,omitting the cumbersome weight setting process in the traditional MPTC.The midpoint potential control strategy is proposed,which uses the characteristics of redundant small vectors to balance the midpoint potential.After that,a fine-division strategy is proposed,which effectively reduces the number of candidate vectors and the computational burden of the system.Finally,the proposed MPFC is compared with MPTC by simulation.The results show that the proposed fine-division MPFC effectively reduces the system calculation,and has the advantages of simple principle and better dynamic and steady-state control performance.The feasibility of the control strategy is verified.

Visualization and Quantitative Evaluation of Eddy Current Loss in Bar-Wound Type Permanent Magnet Synchronous Motor for Mild-Hybrid Vehicles

This paper describes the conductor eddy current loss that occurs in a permanent magnet type synchronous motor with a distributed winding stator using a rectangular copper wire designed for mild hybrid system applications for small vehicles.Compared with the conventional round wire inserter method,the space factor can be improved and the coil-end length can be shortened by applying a so-called hairpin windings using a pre-formed into hairpin shape of bar conductor,and as a result,DC current resistance of the armature winding can be reduced.However,since the conductor cross-sectional area tends to increases,the conductor eddy current loss generated by the space harmonics linkage becomes too large to ignore.In order to study the reduction of the conductor eddy current loss,it is important to visualize the spatial leakage flux distribution which causes loss and finely analyze how the magnetic path is formed.Therefore,analysis of the conductor eddy current loss distribution generated in the bar-wound conductor is performed using the CAE model that faithfully reproduces the coil-end shape of the actual machine.Furthermore,it was qualitatively clarified what ratio of conductor eddy current loss at various driving points.Finally,the results of preliminary study on reduction of conductor eddy current loss are reported.

Cogging Torque Reduction in Axial Flux PMSM with Different Permanent Magnet Combination

With the increasing requirement for the mechanical vibration and acoustic noise of the permanent magnet synchronous motor(PMSM)drive system,the demand for cogging torque reduction of PMSM has been considerably increased.To solve the problem of oversized cogging torque of axial flux PMSM,a rotor topology with hybrid permanent magnet is proposed to weaken the cogging torque.Firstly,the expression of the cogging torque of the axial flux motor is derived,and the influence of the pole-arc ratio of the permanent magnet on the cogging torque is analyzed.Secondly,the rotor structure with hybrid permanent magnet is adopted to reduce the cogging torque.According to the analytical analysis,the constraints of the size and pole-arc ratio between the hybrid permanent magnets are obtained,and the two permanent magnets related to the minimum cogging torque are determined.And the analysis results are verified by the finite element simulation.Furthermore,the motor performance with and without the hybrid permanent magnet is compared with each other.Finally,the cogging torque is significantly reduced by adopting a rotor structure with hybrid permanent magnets.

Variable-Flux Outer-Rotor Permanent Magnet Synchronous Motor for In-Wheel Direct-Drive Applications

In-wheel direct-drive is the most efficient driving mode for electric vehicles,and it is the trend for applications in the future.In this paper,a novel variable-flux outer-rotor permanent magnet synchronous motor with a hybrid magnetic structure design is developed.Due to the hybrid magnetic pole with Nd-Fe-B and Al-Ni-Co permanent magnet(PM),the air-gap flux can be adjusted by changing the magnetization states of Al-Ni-Co PM,which is beneficial to realize a wide range of speeds and loads from the electromagnetic structure design.Firstly,basic structure features of the motor and the flux-adjusting principle are introduced.The design and calculation method of the PM dimensions is derived based on magnetic circuit analysis.Then the Preisach hysteresis model of Al-Ni-Co PM is described and is adopted to analyze the motor performance with the coupling of the time step finite element method(FEM),and the magnetization are investigated.Finally,the operational performance of the proposed motor is obtained by simulation,which verifies the design.

基于滑模变结构的风电机组一次调频算法研究

针对并网风电场中,经典一次调频控制方法存在抗干扰能力弱、机组易脱网的问题,提出一种基于滑模变结构的风电机组一次调频控制算法。首先,在永磁同步风电机组工作原理的基础上,建立含有大电网的风电机组模型。其次,为了解决传统比例积分微分(proportional integral differential,PID)控制下抗干扰能力弱的问题、引入经典滑模变结构控制器。然后,针对经典滑模变结构控制器导致执行机构存在抖振较多的缺点,提出一种基于sigmoid函数趋近率的滑模变结构一次调频控制算法。最后,通过MATLAB/Simulink对风电机组一次调频进行建模仿真,并与经典控制算法相比,验证了所提算法的可行性,在风速波动和电网故障的环境下,滑模变结构一次调频控制算法更具有效性。

基于变载波频率的永磁同步电机驱动系统效率优化控制

为降低永磁同步电机驱动系统的损耗,提高系统效率,提出了一种基于母线电流反馈的变载波频率优化控制方法.首先,建立了系统损耗数学模型,探究了载波频率与系统损耗的关系.然后,针对离线优化方法对于参数敏感的问题,设计了一种基于母线电流反馈的载波频率在线寻优方法.结果表明,在不同转速与负载条件下均存在使系统损耗最小的最优载波频率,其随转速与负载条件变化而变化.在各个工作点,系统损耗的计算值均与实测值基本吻合.在线寻优方法在中高负载情况下能够实现约0.6%的效率优化,并且在负载变化的情况下仍然能够实现损耗优化.

基于径向气隙磁密和定子电流的永磁同步电机均匀退磁故障诊断研究

该文提出一种基于径向气隙磁密和定子电流的永磁同步电机均匀退磁故障诊断方法。首先,建立电机的d轴等效磁路模型,分析均匀退磁故障后径向气隙磁密的变化规律;然后,获取电机的径向气隙磁密和定子电流信号,对各极下径向气隙磁密幅值进行归一化处理,并绘制雷达图,根据雷达图和比较相同定子电流幅值下健康电机和故障电机的各极下径向气隙磁密幅值的平均值,来诊断均匀退磁故障;利用空载各极下径向气隙磁密幅值的平均值计算故障程度。最后,仿真和实验结果均验证所提均匀退磁故障诊断方法的有效性。

基于六边形轨迹的永磁辅助式同步磁阻电机弱磁控制策略

永磁辅助式同步磁阻电机在高速工况弱磁运行时,直流母线电压利用率不高,电机的效率与转矩输出能力较低。为此,提出了一种基于六边形轨迹的永磁辅助式同步磁阻电机弱磁控制策略。首先,以永磁辅助式同步磁阻电机的d-q轴等效电路为基础,推导了弱磁过程的电压和电流约束,证明弱磁控制提升电机调速能力的根本原因。其次,为充分发挥永磁辅助式同步磁阻电机高速运行下功率密度较高的优势,进而推导过调制算法。并将其应用于永磁辅助式同步磁阻电机的弱磁操作中,以实现更高的直流母线电压利用率。最后,通过仿真验证所提出方法的有效性。

考虑磁链变化率的永磁同步电机失磁故障复合容错控制

针对永磁同步电机(PMSM)失磁故障中磁链变化较快,近似认为磁链变化率为0会导致传统PMSM失磁容错控制方法性能受限的问题,本文提出一种基于智能比例积分微分的无模型超螺旋滑模复合容错控制(iPID-MFSTSMC)方法。首先,构建考虑永磁体磁链变化量的PMSM失磁故障数学模型,根据这一模型设计了磁链滑模观测器,实现了对于磁链及其变化率的观测。此外,针对快速变化的负载转矩设计了负载转矩导数滑模观测器。然后,基于磁链及其变化率、负载转矩导数的观测,设计了iPID无模型容错控制方法,该方法采用超螺旋滑模算法对观测误差及其他扰动进行抑制,改善了动态性能且降低了控制器参数的设计难度。利用Lyapunov稳定性定理证明了所设计容错控制方法的稳定性,并给出了参数的设计条件。最后,在磁链以及负载转矩快速变化工况下,通过仿真和实验分析表明,该方法可以有效减少系统抖振并降低超调量。

船舶永磁同步推进电机的优化I/f起动控制方法

为解决高转矩与高转动惯量的船舶推进电机在开环I/f控制中转速和转矩波动大、电机易失步、效率低的问题,提出一种I/f控制改进方法。通过建立转矩角观测器,调节给定电流矢量的幅值,使其跟随负载转矩变化,提高系统鲁棒性。同时,将电机运行状态推进至接近最大转矩电流比状态,提高电机的运行效率;通过瞬时有功功率调节电流矢量的角速度,降低电磁转矩波动,加快电机的转速收敛过程。最后,在Matlab/Simulink中进行仿真实验,实验结果表明该方法可以显著提高推进电机运行效率和稳定性。

基于磁链相移原理的不对称交替极永磁辅助同步磁阻电机设计与分析

传统永磁辅助同步磁阻电机(PMaSynRM)无法充分利用永磁转矩和磁阻转矩,该文提出一种新型不对称交替极永磁辅助同步磁阻电机(ACP-PMaSynRM)。基于永磁磁链相移原理,将交替极永磁阵列、不对称磁极和磁障相结合,实现永磁转矩和磁阻转矩的最大值在相同电流相位下叠加,不但提高了永磁转矩和磁阻转矩的利用率,增强了电机输出转矩能力,而且减少了永磁体用量。采用有限元法对比分析了传统和新型ACP-PMaSynRM的电磁性能,验证了所提电机拓扑的可行性。最后,制造了一台48槽14极样机并对其进行了实验验证。

永磁同步电机全转速范围无位置传感器控制

为解决IF控制启动速度偏慢、启动转矩能力薄弱等问题,采用高频脉振电压注入法完成电动机零低速启动,并结合中高速区有效磁链法形成全转速范围无位置传感器复合控制策略。为了实现两种控制方法的平滑切换,提出一种基于转速过渡区与状态机结合的滞环切换策略,所提策略将全转速范围划分为零低速区、过渡区以及中高速区,电动机由中高速区进入过渡区时提前开启高频脉振电压注入法,使其位置估计过程达到稳定,为切换做好准备。为了减小注入高频电压对有效磁链法位置估计过程的冲击,在转速过渡区采用软开启的方式实现高频脉振电压注入法的投入与退出。针对转速过渡区两种位置估计方法同时工作时的耦合问题,设置了双同步旋转坐标系,实现了转子位置估计的解耦控制。在一台三相永磁同步电机上对所提方法的有效性进行了验证。

Design of a PCB stator coreless axial flux permanent magnet synchronous motor based on a novel topology Halbach array

A novel topology Halbach permanent magnet array is proposed and applied to the design of a printed circuit board(PCB) axial flux permanent magnet(AFPM) motor. Compared with the traditional coreless AFPM motor, this novel topology for a Halbach permanent magnet array PCB stator AFPM motor has larger air-gap magnetic flux density and air-gap flux per pole. The magnetic flux leakage is effectively reduced, and the air-gap magnetic density is close to the sine wave. Results of the finite element analysis and prototype experiments verify the feasibility and effectiveness of the novel Halbach permanent magnet array PCB stator motor. A reference basis and practical value for the design of the PCB AFPM motor are provided.

新型双定子双凸极可变磁通记忆电机设计与性能比较

结合双凸极结构、双定子和混合永磁体的特点,提出了三种新型双定子双凸极可变磁通记忆电机(DS-DSVFMM)。通过采用高矫顽力和低矫顽力两组永磁体,实现了电机的高转矩密度和在线调磁功能。为了充分利用电机的内部空间,高矫顽力和低矫顽力永磁体以及调磁绕组都被放置在内定子中。建立该电机的简化等效磁路模型,并分析其磁通调节原理和特性;对三种不同结构DS-DSVFMM的调磁能力、负载转矩和抗退磁性能进行了研究和比较。对T形DS-DSVFMM进行加工和测试,并通过实验验证了该电机结构及其有限元分析的正确性。

车用永磁同步电机高性能弱磁控制策略

提出一种基于电流预测的车用永磁同步电机弱磁控制方法,以提升永磁同步电机弱磁区的动态性能。详细分析了弱磁区的电压边界问题,以及不同电压选取规则下的稳定性问题。在此基础上,提出了一种考虑稳定性和动态特性的动态过调制策略。此外,研究了基于参数模型的电流预测控制算法,该算法具有快速动态响应和可控约束的优点,在保证稳定性的基础上可有效提升电机弱磁区域动态性能。最后,分别在仿真和实验平台上证明了所提算法的有效性。

永磁同步电机变频调速系统动态解耦控制方法

常规的永磁同步电机变频调速系统解耦控制,主要采用系统反馈信号完成解耦控制,忽略了反馈信号的预测误差,导致解耦控制结果负荷响应幅值不够稳定.因此,提出永磁同步电机变频调速系统动态解耦控制方法.建立系统数学模型,在该模型中分离系统模式系数获取控制信号,对该信号进行优化处理,基于输出期望值计算预测误差,加权修正预测值,形成动态控制信号,分离有功-无功信号实现动态解耦控制.实验结果表明:所提方法应用后得出的动态解耦控制结果,表现出的负荷响应幅值较为稳定,满足了永磁同步电机变频调速系统的实际解耦控制需求.

基于槽极比选择的切向永磁同步电机永磁体涡流损耗抑制措施

为抑制切向永磁同步电机的永磁体涡流损耗,基于麦克斯韦方程和本构方程,对永磁体形状进行近似假设,构建了永磁体涡流损耗的估算模型。使用一种基于卡特系数概念的磁导函数来估算由于定子开槽引起的槽下磁感应强度变化。基于五台槽极比分别为1.05、1.20、1.30、2.40和3.60的电机设计方案对理论分析结论进行了验证。在负载电流和两倍负载电流下,分析永磁体损耗,得到了每台电机的径向气隙磁密曲线及其谐波含量。考虑到增加槽极比对定子铁耗和永磁体涡流损耗的削弱效果,给出了电机槽极比选择策略。研究结果表明,增加槽极比能减弱定子槽下磁感应强度变化,从而抑制气隙磁场中低次谐波含量,减小永磁体涡流损耗,使电机运行更加可靠,但也会引入更多高次谐波,从而增加定子铁耗。

交流调磁型永磁同步电机磁通协同调控最大转矩铜耗比控制

电动汽车驱动系统不仅需要拥有宽广的调速范围和恒功率运行区域,还应具备高效率、低损耗的优点,以实现续航的最大化。针对这些技术特点,该文研究了一种调磁性能优越的交流调磁型永磁同步电机(ACFR-PMSM),分别建立其等效磁路模型和稳态数学模型。并以该电机特殊的径向-轴向结构为基础,研究了其电感特性和转矩输出特性,从理论的角度论证了实现最大转矩铜耗比(MTPCL)控制的可行性。另外,分别采用拉格朗日乘子法和电流选择穷举法,获得了MTPCL控制的径-轴向定子绕组最佳电流选择方案。最后,实现了所提出控制策略的计算机仿真和样机测试,验证了其良好的动态控制性能,详细对比了经典id=0控制和所提出MTPCL控制的实施效果并计算了运行铜耗。