A double invert variable polarity plasma arc （VPPA） power source based on 16-bit MCU applied for aluminum alloys was developed. Mechanics, electrical and the produced heat mechanism of VPPAW arc were tested and anal...A double invert variable polarity plasma arc （VPPA） power source based on 16-bit MCU applied for aluminum alloys was developed. Mechanics, electrical and the produced heat mechanism of VPPAW arc were tested and analyzed. Results indicate that during the VPPA welding procedure of aluminum alloy, the arc of electrode negative （EN） has more effect on force, whereas the arc of electrode positive （ EP ） has more effect on heat. It should be noted that keeping the balance of the force and heat is the critical element of VPPAW. This power source had been successfully used to weld aluminum alloy with a 15 mm thickness in vertical welding. The conclusions are applicable to the variable polarity plasma arc welding technique used in the aerospace industry.展开更多
Arc pressure is one of the key factors for variable polarity plasma arc（VPPA） and welding pool formation. In this paper, VPPA pressure is measured by pressure transducer and U-tube barometer methods, and advantages ...Arc pressure is one of the key factors for variable polarity plasma arc（VPPA） and welding pool formation. In this paper, VPPA pressure is measured by pressure transducer and U-tube barometer methods, and advantages and disadvantages of the two methods are compared. The effects of welding parameters, including with straight polarity（SP） current, reverse polarity（RP） current, time ratio of SP to RP, plasma gas flow rate, on VPPA pressure are investigated by using an orthogonal design. The experimental results indicate that the influencing degree of the welding parameters are in the order of plasma gas flow rate, SP current, time ratio of SP to RP, RP current. These results are important to researches of VPPA welding process and its mechanism. The physics behavior of VPPA is taken into account when the above influence mechanisms are analyzed. Firstly, according to the mechanism of the cooling compression to the arc, the compression to VPPA is enhanced with the increase of plasma gas flow, so the VPPA pressure would increase obviously. Secondly, although the temperature of VPPA is as a function of the welding current, the radius of VPPA is also enhanced. So the effects of SP current on VPPA pressure are inferior to the effects of plasma gas flow. Thirdly, VPPA pressure increases as a function of time ratio of SP to RP because the frequency of welding current influences the arc pressure to the some degree; Finally, the RP intervals are farther less than the SP intervals, so the influence to the pressure is minimal.展开更多
Abstract Horizontal welding is important for heavy or huge welding structures. Keyhole mode variable polarity plasma arc welding of aluminum alloy plates with medium thickness was carried out in horizontal position. T...Abstract Horizontal welding is important for heavy or huge welding structures. Keyhole mode variable polarity plasma arc welding of aluminum alloy plates with medium thickness was carried out in horizontal position. The characteristic of welding defects was introduced. Preliminary experiments indicated that the undercut defect could not be eliminated easily. The relationship between welding parameters and the undercut defect showed that this deject could be lessened by using higher heat input. The fluid flow of weld pool was observed by a high speed camera. The fluid flow in weld pool was not symmetric and much of molten metal gathered in the lower part. The fluid flow velocity in the lower part was bigger than that in the upper part. To this end, the formative mechanism of the undercut defect was proposed. The flowability of the molten metal was an influential factor for the undercut defect. A preheating method was designed to verify the formative mechanism.展开更多
The mechanical properties of the 2219 aluminum alloy welded joints by vertical-up variant polarity plasma arc welding (VPPAW) with keyhole were analyzed. The tensile strength of welded joints can reach 55% of that of ...The mechanical properties of the 2219 aluminum alloy welded joints by vertical-up variant polarity plasma arc welding (VPPAW) with keyhole were analyzed. The tensile strength of welded joints can reach 55% of that of base metal. The microstructure of weld joints was studied to explain the mechanical properties of the weld. The results show that the intensity of weld center is less than that of HAZ, and the intensity of weld center is the worst. So an advanced welding procedures is presented to reduce the heat input and increase the welding speed. The results in this procedures show that the tensile strength of welded joints reaches more than 60% of that of the parent metal, and the specific elongation does not descend.展开更多
Variable polarity plasma arc welding (VPPAW) is one of the most excellent processes used for welding aluminum alloys recently. It combines the advantages of variable polarity welding and plasma arc welding, and can ac...Variable polarity plasma arc welding (VPPAW) is one of the most excellent processes used for welding aluminum alloys recently. It combines the advantages of variable polarity welding and plasma arc welding, and can achieve the most rational heat distribution and cathodic cleaning. With the VPPAW equipment developed by authors, the cathodic cleaning regularity that is one of the most important problems in VPPAW is investigated in this paper. The results will be helpful in realizing the real cleaning mechanism.展开更多
Variable polarity plasma arc-gas metal arc welding(VPPA-GMAW)integrates the advantages of VPPA and GMAW,and it is particularly applied to weld thick-plates aluminum alloys.High-speed camera and data acquisition system...Variable polarity plasma arc-gas metal arc welding(VPPA-GMAW)integrates the advantages of VPPA and GMAW,and it is particularly applied to weld thick-plates aluminum alloys.High-speed camera and data acquisition system were used to analyze the arc shape and the welding process electrical signal.According to the analysis of arc swing amplitude and the approximate entropy of arc voltage signal denoised by wavelet threshold method,the influence of VPPA frequency on the arc stability was studied.The results show that the approximate entropy of GMAW arc voltage decreases with the increase of VPPA frequency in a certain range,and the stability of the hybrid arc is significantly improved.The spectral analysis shows that the arc stability is reduced due to the resonance effect between the VPPA and the GMAW arc when the VPPA frequency closes to the GMAW arc pulse frequency.The results are helpful to understand hybrid welding mechanism and the selection of welding process parameters.展开更多
VPPA-MIG复合焊集VPPA穿透力强和MIG焊熔敷效率高的优点,弥补了单VPPA焊工艺区间窄且需立焊和MIG焊熔深浅的不足.使用Red Lake Y4高速摄像获取6 mm厚2A12铝合金VPPA-MIG复合焊接熔池图像,建立了熔池受力模型.对比分析了复合热源不同能...VPPA-MIG复合焊集VPPA穿透力强和MIG焊熔敷效率高的优点,弥补了单VPPA焊工艺区间窄且需立焊和MIG焊熔深浅的不足.使用Red Lake Y4高速摄像获取6 mm厚2A12铝合金VPPA-MIG复合焊接熔池图像,建立了熔池受力模型.对比分析了复合热源不同能量配比对焊缝成形和熔池形貌的影响及VPPA-MIG与单MIG焊缝成形特点.结果表明,VPPA-MIG复合热源相比单VPPA热源易保持焊缝成形稳定性.VPPA电流接近穿孔阈值时,配合较低功率MIG热源可以获得6 mm厚2A12铝合金良好焊缝成形;VPPA能量比例过低时,小孔较浅,熔化效率较低,不能起到增加熔深的作用;VPPA能量比例过大,易使熔池失稳,焊缝成形不良.热源输入功率相同时,VPPA-MIG复合焊比MIG焊显著增加焊缝熔深和深宽比,提高生产效率.展开更多
基金This work was supported by the National Nature Science Foundation of China （ Grant No. 50764007）.
文摘A double invert variable polarity plasma arc （VPPA） power source based on 16-bit MCU applied for aluminum alloys was developed. Mechanics, electrical and the produced heat mechanism of VPPAW arc were tested and analyzed. Results indicate that during the VPPA welding procedure of aluminum alloy, the arc of electrode negative （EN） has more effect on force, whereas the arc of electrode positive （ EP ） has more effect on heat. It should be noted that keeping the balance of the force and heat is the critical element of VPPAW. This power source had been successfully used to weld aluminum alloy with a 15 mm thickness in vertical welding. The conclusions are applicable to the variable polarity plasma arc welding technique used in the aerospace industry.
基金supported by Key Project of National Natural Science Foundation of China (Grant No.50735006)National Basic Research Program of China(973 Program, Grant No. 2007CB607601)General Project of National Natural Science Foundation of China (Grant No.50675223)
文摘Arc pressure is one of the key factors for variable polarity plasma arc（VPPA） and welding pool formation. In this paper, VPPA pressure is measured by pressure transducer and U-tube barometer methods, and advantages and disadvantages of the two methods are compared. The effects of welding parameters, including with straight polarity（SP） current, reverse polarity（RP） current, time ratio of SP to RP, plasma gas flow rate, on VPPA pressure are investigated by using an orthogonal design. The experimental results indicate that the influencing degree of the welding parameters are in the order of plasma gas flow rate, SP current, time ratio of SP to RP, RP current. These results are important to researches of VPPA welding process and its mechanism. The physics behavior of VPPA is taken into account when the above influence mechanisms are analyzed. Firstly, according to the mechanism of the cooling compression to the arc, the compression to VPPA is enhanced with the increase of plasma gas flow, so the VPPA pressure would increase obviously. Secondly, although the temperature of VPPA is as a function of the welding current, the radius of VPPA is also enhanced. So the effects of SP current on VPPA pressure are inferior to the effects of plasma gas flow. Thirdly, VPPA pressure increases as a function of time ratio of SP to RP because the frequency of welding current influences the arc pressure to the some degree; Finally, the RP intervals are farther less than the SP intervals, so the influence to the pressure is minimal.
基金This research is supported by the National Natural Science Foundation of China （Grant No. 51475105）.
文摘Abstract Horizontal welding is important for heavy or huge welding structures. Keyhole mode variable polarity plasma arc welding of aluminum alloy plates with medium thickness was carried out in horizontal position. The characteristic of welding defects was introduced. Preliminary experiments indicated that the undercut defect could not be eliminated easily. The relationship between welding parameters and the undercut defect showed that this deject could be lessened by using higher heat input. The fluid flow of weld pool was observed by a high speed camera. The fluid flow in weld pool was not symmetric and much of molten metal gathered in the lower part. The fluid flow velocity in the lower part was bigger than that in the upper part. To this end, the formative mechanism of the undercut defect was proposed. The flowability of the molten metal was an influential factor for the undercut defect. A preheating method was designed to verify the formative mechanism.
文摘The mechanical properties of the 2219 aluminum alloy welded joints by vertical-up variant polarity plasma arc welding (VPPAW) with keyhole were analyzed. The tensile strength of welded joints can reach 55% of that of base metal. The microstructure of weld joints was studied to explain the mechanical properties of the weld. The results show that the intensity of weld center is less than that of HAZ, and the intensity of weld center is the worst. So an advanced welding procedures is presented to reduce the heat input and increase the welding speed. The results in this procedures show that the tensile strength of welded joints reaches more than 60% of that of the parent metal, and the specific elongation does not descend.
文摘Variable polarity plasma arc welding (VPPAW) is one of the most excellent processes used for welding aluminum alloys recently. It combines the advantages of variable polarity welding and plasma arc welding, and can achieve the most rational heat distribution and cathodic cleaning. With the VPPAW equipment developed by authors, the cathodic cleaning regularity that is one of the most important problems in VPPAW is investigated in this paper. The results will be helpful in realizing the real cleaning mechanism.
基金supported by the National Natural Science Foundation of China(51665044)Natural Science Foundation of Inner Mongolia(2019LH05017)+1 种基金Science and Technology Programs of Inner Mongolia(2020GG0313)Major Basic Research Open Subjects of Inner Mongolia Autonomous Region.
文摘Variable polarity plasma arc-gas metal arc welding(VPPA-GMAW)integrates the advantages of VPPA and GMAW,and it is particularly applied to weld thick-plates aluminum alloys.High-speed camera and data acquisition system were used to analyze the arc shape and the welding process electrical signal.According to the analysis of arc swing amplitude and the approximate entropy of arc voltage signal denoised by wavelet threshold method,the influence of VPPA frequency on the arc stability was studied.The results show that the approximate entropy of GMAW arc voltage decreases with the increase of VPPA frequency in a certain range,and the stability of the hybrid arc is significantly improved.The spectral analysis shows that the arc stability is reduced due to the resonance effect between the VPPA and the GMAW arc when the VPPA frequency closes to the GMAW arc pulse frequency.The results are helpful to understand hybrid welding mechanism and the selection of welding process parameters.
文摘VPPA-MIG复合焊集VPPA穿透力强和MIG焊熔敷效率高的优点,弥补了单VPPA焊工艺区间窄且需立焊和MIG焊熔深浅的不足.使用Red Lake Y4高速摄像获取6 mm厚2A12铝合金VPPA-MIG复合焊接熔池图像,建立了熔池受力模型.对比分析了复合热源不同能量配比对焊缝成形和熔池形貌的影响及VPPA-MIG与单MIG焊缝成形特点.结果表明,VPPA-MIG复合热源相比单VPPA热源易保持焊缝成形稳定性.VPPA电流接近穿孔阈值时,配合较低功率MIG热源可以获得6 mm厚2A12铝合金良好焊缝成形;VPPA能量比例过低时,小孔较浅,熔化效率较低,不能起到增加熔深的作用;VPPA能量比例过大,易使熔池失稳,焊缝成形不良.热源输入功率相同时,VPPA-MIG复合焊比MIG焊显著增加焊缝熔深和深宽比,提高生产效率.
