Noise cancellation of a multi-reference full-wave magnetic resonance sounding signal based on a modified sigmoid variable step size least mean square algorithm

Nano-volt magnetic resonance sounding(MRS) signals are sufficiently weak so that during the actual measurement, they are affected by environmental electromagnetic noise, leading to inaccuracy of the extracted characteristic parameters and hindering effective inverse interpretation. Considering the complexity and non-homogeneous spatial distribution of environmental noise and based on the theory of adaptive noise cancellation, a model system for noise cancellation using multi-reference coils was constructed to receive MRS signals. The feasibility of this system with theoretical calculation and experiments was analyzed and a modified sigmoid variable step size least mean square(SVSLMS) algorithm for noise cancellation was presented. The simulation results show that, the multi-reference coil method performs better than the single one on both signal-to-noise ratio(SNR) improvement and signal waveform optimization after filtering, under the condition of different noise correlations in the reference coils and primary detecting coils and different SNRs. In particular, when the noise correlation is poor and the SNR<0, the SNR can be improved by more than 8 dB after filtering with multi-reference coils. And the average fitting errors for initial amplitude and relaxation time are within 5%. Compared with the normalized least mean square(NLMS) algorithm and multichannel Wiener filter and processing field test data, the effectiveness of the proposed method is verified.

A novel dynamic step size LMS optimization scheme for interference reducing in FBMC-QAM

Filter bank multicarrier quadrature amplitude modulation(FBMC-QAM)will encounter inter-ference and noise during the process of channel transmission.In order to suppress the interference in the communication system,channel equalization is carried out at the receiver.Given that the con-ventional least mean square(LMS)equilibrium algorithm usually suffer from drawbacks such as the inability to converge quickly in large step sizes and poor stability in small step sizes when searching for optimal weights,in this paper,a design scheme for adaptive equalization with dynamic step size LMS optimization is proposed,which can further improve the convergence and error stability of the algorithm by calling the Sigmoid function and introducing three new parameters to control the range of step size values,adjust the steepness of step size,and reduce steady-state errors in small step sta-ges.Theoretical analysis and simulation results demonstrate that compared with the conventional LMS algorithm and the neural network-based residual deep neural network(Res-DNN)algorithm,the adopted dynamic step size LMS optimization scheme can not only obtain faster convergence speed,but also get smaller error values in the signal recovery process,thereby achieving better bit error rate(BER)performance.

Active micro-vibration control based on improved variable step size LMS algorithm

The contradiction of variable step size least mean square(LMS)algorithm between fast convergence speed and small steady-state error has always existed.So,a new algorithm based on the combination of logarithmic and symbolic function and step size factor is proposed.It establishes a new updating method of step factor that is related to step factor and error signal.This work makes an analysis from 3 aspects:theoretical analysis,theoretical verification and specific experiments.The experimental results show that the proposed algorithm is superior to other variable step size algorithms in convergence speed and steady-state error.

Novel LMS adaptive filtering algorithm with variable step size

By analyzing algorithms available for variable step size least mean square(LMS)adaptive filter,a new modified LMS adaptive filtering algorithm with variable step size is proposed,along with performance analysis based on different parameters.Compared with the existing algorithms through the simulation,the proposed algorithm has faster convergence speed and smaller steady state error.

Lattice structure adaptive IIR notch filter based on least square kurtosis

A new variable step-size algorithm for a second-order lattice form structure adaptive infinite impulse response （IIR） notch filter to detection and estimation frequency of sinusoids in Gaussian noises is proposed. Utilizing least square kurtosis of output signals as a cost function, the new gradient-based algorithm to update frequency of the adaptive IIR notch filter and the new variable step-size algorithm are given. The computer simulation results show that the proposed algorithm has better ability in suppressing colored Gaussian noises and better accuracy in estimating parameters at low SNR than previous algorithms.

一种适用于复杂电网下的高精度锁相环

针对现有并网逆变器在电网电压谐波复杂的情况下难以精确锁定电压频率和相位的问题,结合传统锁相环结构与自适应算法的理论提出一种高精度的锁相方法。依据对传统锁相环在复杂电网下的弊端分析,确定了锁相环采用传统低通滤波器、带通滤波器时的滤波效果与延时的矛盾关系。根据最小均方算法的高自适应特性与快速跟踪特点,结合锁相环中坐标变换公式,确定算法的输入输出以及权重矩阵,构建基于派克变换的最小均方算法矩阵模型。通过将所需的电压正序分量设置为不断更新的权重矩阵来进行高精度的滤波,同时通过引入均方瞬时误差和自相关估计均值来进行变步长控制,提高滤波更新速度,以适用于复杂程度不确定的电网电压进行自适应滤波锁相。对仿真和样机实验的结果表明:采用基于派克变换的最小均方算法的改进型双二阶广义积分锁相方法,可以在不降低动态响应速度的前提下,提高锁相环的滤波效果,进而提高并网逆变器在电网畸变严重场景下锁定电压频率和相位的跟踪精度。

基于小波变换的有源噪声控制算法研究

在传统的有源噪声控制系统中,原始噪声信号是获得参考噪声信号的必要条件,当原始噪声信号的信息不可获知时,有源噪声控制系统失效。为解决该问题,设计基于小波变换的有源噪声控制系统,利用小波阈值法对含噪语音信号进行处理,得到与原始噪声信号相关的参考噪声信号。在此基础上,对传统的有源噪声控制算法LMS进行改进,提出基于Sigmoid函数的γSLMS算法和C-γSLMS凸组合算法,解决LMS算法无法同时兼顾收敛速度和稳态误差的问题,为解决有源噪声控制问题提供新的解决方案。

基于sigmoid-sinh分段函数的变步长FxLMS算法

为改善滤波-x最小均方(filtered-x least mean square,FxLMS)算法在噪声主动控制时无法兼顾收敛速度和稳态误差的问题,提出了基于sigmoid-sinh分段函数的FxLMS(SSFxLMS)算法,并引入蚁狮算法对SFxLMS(sigmoid filtered-x least mean square)、ShFxLMS(sinh filtered-x least mean square)、SSFxLMS算法的参数进行优化。分别采用高斯白噪声和实测簇绒地毯织机噪声为输入信号,采用FxLMS、SFxLMS、ShFxLMS、SSFxLMS算法进行噪声主动控制仿真,对比分析这4种算法的性能。结果表明:与其他3种算法相比,采用SSFxLMS算法对高斯白噪声和簇绒地毯织机噪声进行控制时,误差信号的平均绝对值更小,平均降噪量与收敛速度也有大幅度提升。由此可知,SSFxLMS算法有效改善了FxLMS算法无法兼顾收敛速度和稳态误差的问题,研究结果为噪声主动控制算法设计提供了一定的参考。

双曲正切函数的新型变步长LMS算法

针对自适应最小均方误差(Least Mean Square,LMS)滤波算法迭代步长在算法收敛速度、稳态误差间的折中问题,设计了一种基于双曲正切函数的新型变步长算法,算法以双曲正切函数为基础,建立步长因子μ(n)与误差信号e(n)的非线性函数关系,并引入参数α、β和m,设计了一种新的步长调整公式,使得在算法迭代初始阶段采用较大步长因子,达到更快的收敛速度,在接近收敛时采用较小的步长因子,获得更小的稳态误差。通过仿真分析了不同参数对算法性能的影响,与已有典型变步长算法相比,论文算法具有更快的收敛速度、更小的稳态误差和更优的追踪能力。

变步长CMA和DD-LMS双模式切换盲均衡算法

针对经典盲均衡算法收敛速度较慢和稳态误差较大的问题,提出了一种基于变步长恒模算法(Constant Modulus Algorithm, CMA)和判决引导的最小均方(Decision Directed Least Mean Square, DD-LMS)算法的双模式切换盲均衡算法。在算法收敛初期采用CMA算法,以确保算法可以较快收敛。在收敛之后切换至DD-LMS算法,以进一步降低稳态误差。通过设定阈值来切换算法,取相邻多次迭代误差的平均值作为算法的切换值,以确保算法切换时机的合理性。另外,引入Softsign变步长函数并加入3个参数对该函数进行改进,使得Softsign变步长函数可以依据不同信道环境设定最佳参数,同时提高算法的收敛速度。仿真结果表明,在卫星通用信道条件下,所提算法的收敛迭代次数约为1 000次,稳态误差为-12 dB,在信噪比为15 dB时,误码率为1×10~(-6)。与相关算法对比,所提算法的收敛速度较高,误码率和稳态误差较低。

New normalized LMS adaptive filter with a variable regularization factor

A new normalized least mean square(NLMS) adaptive filter is first derived from a cost function, which incorporates the conventional one of the NLMS with a minimum-disturbance(MD)constraint. A variable regularization factor(RF) is then employed to control the contribution made by the MD constraint in the cost function. Analysis results show that the RF can be taken as a combination of the step size and regularization parameter in the conventional NLMS. This implies that these parameters can be jointly controlled by simply tuning the RF as the proposed algorithm does. It also demonstrates that the RF can accelerate the convergence rate of the proposed algorithm and its optimal value can be obtained by minimizing the squared noise-free posteriori error. A method for automatically determining the value of the RF is also presented, which is free of any prior knowledge of the noise. While simulation results verify the analytical ones, it is also illustrated that the performance of the proposed algorithm is superior to the state-of-art ones in both the steady-state misalignment and the convergence rate. A novel algorithm is proposed to solve some problems. Simulation results show the effectiveness of the proposed algorithm.

一种改进的K-means聚类算法

针对K-means聚类算法对初始聚类中心敏感,容易陷入局部最优解的问题,提出了一种基于天牛须搜索算法优化的K-means算法,利用天牛须搜索算法的全局搜索能力在聚类算法更新聚类中心时进行全局寻优。优化后的算法在五种公开数据集上进行对比实验,结果显示优化后的算法在聚类性能和准确率上均高于两种对比算法,为K-means聚类算法的优化提供了一个行之有效的方法。

基于智能电网的频谱感知算法研究

宽带微功率(Broadband Micro-Power, BMP)无线通信系统是为满足智能配用电系统的通信需求,在非授权频谱资源上研究开发的电力无线专网系统。认知无线电(Cognitive Radio, CR)的频谱感知技术的引入,虽缓解了目前智能电网频谱资源紧张的问题,但系统在低信噪比下单用户的感知准确性仍需提高。针对上述问题,提出一种基于变步长的最小均方(Variable Step Size Least Mean Square, VSS-LMS)频谱感知算法。该算法在对原始发送信号幅度进行迭代估计时,增加两个参数作为调节器,可以灵活地调整步长,并对误差信号进行平滑处理,从而解决收敛速度与稳态误差的矛盾,实现高效的频谱感知。仿真实验表明,该算法不仅具有较好的收敛性,且在低信噪比下仍有较好的检测性能。与能量检测算法和LMS频谱感知算法相比,该算法使系统的频谱检测性能得到提升。

基于改进双曲正切函数的变步长最小平均p范数算法

在信号处理领域,传统的自适应滤波算法采用的固定步长会导致稳态误差和收敛速度无法同时兼顾。针对这个问题,对最小平均p范数(Least Mean p-norm,LMP)算法进行改进,提出了一种基于改进双曲正切(tanh)函数的变步长最小平均p范数算法。该算法利用改进的tanh函数来调节步长,采用移动加权平均法构造变步长函数;同时引入了一个调节函数以进一步提升算法的性能。通过在海洋脉冲噪声干扰下进行仿真,实验表明,与已有的固定步长和变步长算法相比,改进的变步长LMP算法较好地兼顾系统的收敛速度和稳态误差;引入调节函数后的新算法在保证原有算法收敛速度的同时进一步降低了算法的稳态误差,从而兼顾了算法的收敛性和稳定性,具有较好的可行性。

基于双曲正弦函数设计变步长的LMS算法

针对非高斯环境下传统变步长LMS(Variable step-size least mean square,VSS-LMS)算法性能不佳的问题,基于传统的VSS-LMS算法利用双曲正弦函数构建变步长的更新策略,提出一种基于双曲正弦函数的变步长LMS算法。并在理论上分析了新提出VSS-LMS算法的收敛性与算法复杂度,并给出在不同输入信号时对两种特性的线性系统的VSS-LMS算法的辨识结果,且每次仿真中都在不同分布的非高斯噪声下进行。结果表明,提出的算法相比Log-NLMS算法和改进G-SVSLMS算法,新提出的VSS-LMS算法具有更快的收敛速度和较好的稳态特性,且稳态误差趋于理论的SNR。

块处理的变步长自适应振动主动控制方法

针对振动主动控制次级通道的时变特点和在线辨识次级通道算法中各通道相互影响,导致控制效果不佳的问题,提出一种基于块处理的变步长自适应振动主动控制方法。根据参考信号和期望信号的功率变化对次级通道辨识和振动控制进行块处理的在线调整步长,排除异常信号干扰,进一步提高辨识精度与速度。仿真结果表明,与原算法比较,该算法的辨识速度和精度均能提升近10%,系统在控制环境突变下能提前近一半时间完成收敛。以单层隔振平台为控制对象对本算法进行实验研究,结果表明,该算法对单层隔振平台的振动响应有较好的控制效果,验证了该算法在实际控制中的有效性。

An Improved Proportionate Normalized Least Mean Square Algorithm for Sparse Impulse Response Identification

In this paper after analyzing the adaptation process of the proportionate normalized least mean square(PNLMS) algorithm, a statistical model is obtained to describe the convergence process of each adaptive filter coefcient. Inspired by this result, a modified PNLMS algorithm based on precise magnitude estimate is proposed. The simulation results indicate that in contrast to the traditional PNLMS algorithm, the proposed algorithm achieves faster convergence speed in the initial convergence state and lower misalignment in the stead stage with much less computational complexity.

自适应变步长LMS滤波算法及分析

为了提高最小均方(LMS)自适应滤波算法的性能,通过建立步长因子与误差信号之间的非线性函数关系,提出一种自适应变步长LMS算法。该算法具有初始阶段和时变阶段步长自适应增大和稳态阶段步长很小的特点,消除了不相关噪声的影响,并且进一步克服了Sigmoid函数变步长LMS算法在自适应稳态阶段步长取值偏大的缺陷,计算机仿真结果与理论分析相一致,证实该算法优于传统算法。

一种新的变步长LMS自适应滤波算法

本文通过建立步长因子μ与误差信号之间的非线性函数关系,提出了一种新的变步长LMS(LeastMean Square)算法.该算法具有初始阶段和未知系统时变阶段步长自动增大而稳态时步长很小的特点,且克服了S函数变步长LMS算法(简称SVSLMS算法)在自适应稳态阶段μ(n)取值偏大的缺陷.理论分析和计算机仿真结果表明该算法的性能优于SVSLMS算法.

基于改进的双曲正切函数变步长LMS算法

为了改进现有的变步长最小均方误差(least mean square,LMS)算法在低信噪比时性能较差的缺陷,提出了一种基于改进的双曲正切函数的变步长LMS算法,从理论分析和仿真实验两方面讨论了引入参数对算法收敛性、跟踪性、稳定性的影响及算法的抗干扰性。理论分析和仿真实验表明该算法在高低信噪比时均具有较快的收敛速度和跟踪速度以及较小的稳态误差和稳态失调,并且在低信噪比时该算法的收敛性、跟踪性、稳态性均优于其他多种变步长算法。