Effect of safety valve types on the gas venting behavior and thermal runaway hazard severity of large-format prismatic lithium iron phosphate batteries

The safety valve is an important component to ensure the safe operation of lithium-ion batteries(LIBs).However,the effect of safety valve type on the thermal runaway(TR)and gas venting behavior of LIBs,as well as the TR hazard severity of LIBs,are not known.In this paper,the TR and gas venting behavior of three 100 A h lithium iron phosphate(LFP)batteries with different safety valves are investigated under overheating.Compared to previous studies,the main contribution of this work is in studying and evaluating the effect of gas venting behavior and TR hazard severity of LFP batteries with three safety valve types.Two significant results are obtained:(Ⅰ)the safety valve type dominates over gas venting pressure of battery during safety venting,the maximum gas venting pressure of LFP batteries with a round safety valve is 3320 Pa,which is one order of magnitude higher than other batteries with oval or cavity safety valve;(Ⅱ)the LFP battery with oval safety valve has the lowest TR hazard as shown by the TR hazard assessment model based on gray-fuzzy analytic hierarchy process.This study reveals the effect of safety valve type on TR and gas venting,providing a clear direction for the safety valve design.

Deep-large faults controlling on the distribution of the venting gas hydrate system in the middle of the Qiongdongnan Basin, South China Sea

Many locations with concentrated hydrates at vents have confirmed the presence of abundant thermogenic gas in the middle of the Qiongdongnan Basin(QDNB).However,the impact of deep structures on gasbearing fluids migration and gas hydrates distribution in tectonically inactive regions is still unclear.In this study,the authors apply high-resolution 3D seismic and logging while drilling(LWD)data from the middle of the QDNB to investigate the influence of deep-large faults on gas chimneys and preferred gasescape pipes.The findings reveal the following:(1)Two significant deep-large faults,F1 and F2,developed on the edge of the Songnan Low Uplift,control the dominant migration of thermogenic hydrocarbons and determine the initial locations of gas chimneys.(2)The formation of gas chimneys is likely related to fault activation and reactivation.Gas chimney 1 is primarily arises from convergent fluid migration resulting from the intersection of the two faults,while the gas chimney 2 benefits from a steeper fault plane and shorter migration distance of fault F2.(3)Most gas-escape pipes are situated near the apex of the two faults.Their reactivations facilitate free gas flow into the GHSZ and contribute to the formation of fracture‐filling hydrates.

GPU parallel computation of dendrite growth competition in forced convection using the multi-phase-field-lattice Boltzmann model

A graphics-processing-unit(GPU)-parallel-based computational scheme is developed to realize the competitive growth process of converging bi-crystal in two-dimensional states in the presence of forced convection conditions by coupling a multi-phase field model and a lattice Boltzmann model.The elimination mechanism in the evolution process is analyzed for the three conformational schemes constituting converging bi-crystals under pure diffusion and forced convection conditions,respectively,expanding the research of the competitive growth of columnar dendrites under melt convection conditions.The results show that the elimination mechanism for the competitive growth of converging bi-crystals of all three configurations under pure diffusion conditions follows the conventional Walton-Chalmers model.When there is forced convection with lateral flow in the liquid phase,the anomalous elimination phenomenon of unfavorable dendrites eliminating favorable dendrites occurs in the grain boundaries.In particular,the anomalous elimination phenomenon is relatively strong in conformation 1 and conformation 2 when the orientation angle of unfavorable dendrites is small,and relatively weak in conformation 3.Moreover,the presence of convection increases the tip growth rate of both favorable and unfavorable dendrites in the grain boundary.In addition,the parallelization of the multi-phase-field-lattice Boltzmann model is achieved by designing the parallel computation of the model on the GPU platform concerning the computerunified-device-architecture parallel technique,and the results show that the parallel computation of this model based on the GPU has absolute advantages,and the parallel acceleration is more obvious as the computation area increases.

Development and Application of Multi-phase Nitrides Bonded Silicon Carbide Lintel Blocks for Dry Quenching Furnaces

Multi-phase nitrides bonded silicon carbide lintel blocks were prepared using industrial SiC(SiC≥98 mass%,3-0.5,≤0.5 and≤0.044 mm),Si powder(Si≥98 mass%,≤0.044 mm),and SiO2 micropowder(SiO2≥96 mass%,d50=0.15 pm)as raw materials,and calcium lignosulfonate as the additive,batching,mixing,and molding on a vibration pressure molding machine,drying and then firing at 1420℃for 10 h in high-purity N2.The apparent porosity,the bulk density,the cold modulus of rupture,the hot modulus of rupture,and the linear expansion coefficient of the samples were tested.The phase composition and the microstructure of the samples at different nitriding depths(50,100,and 150 mm)were analyzed by XRD and SEM.The field application effects of the blocks were studied.The results show that:(1)the multi-phase nitrides bonded silicon carbide refractories can dynamically adjust their own phase composition and minimize structural and thermal stresses,improving the service life of key parts of dry quenching furnaces;(2)calcium lignosulfonate can improve the nitriding micro-environment of multi-phase nitrides bonded silicon carbide lintel blocks,successfully increasing the effective nitriding thickness of the blocks to 300 mm;(3)Sinosteel LI RR provides a unique concept in the design of materials and block types as well as the stable and scientific overall structure,promoting the industrialization process of dry quenching furnaces with long service life in China.

Characteristic of Intelligent Air Bag Venting Structure Actuating by Electrostrictive Stack Actuator

In this paper the conception of smart materials and structures is firstly combined with research of air bag,and the main theory of self adapting cushioning of intelligent air bag is expatiated.The intelligent venting structure is the main part affecting the cushioning result.Electrostrictive material was found having big force,high response speed and wide linearity,and it is fit to utilize in intelligent venting structure. The characteristic of the dynamic response and cushioning actuating of an electrostrictive stack actuator is analyzed,and the result of the computer simulation of the fuzzy control to intelligent venting structure is given.It is concluded that intelligent venting structure has good actuating characteristic and can satisfy the need of intelligent air bag.

Venting Design for Di-tert-butyl Peroxide Runaway Reaction Based on Accelerating Rate Calorimeter Test

In order to design the relief system size of di-tert-butyl peroxide(DTBP) storage tanks,the runaway re-action of DTBP was simulated by accelerating rate calorimeter(ARC).The results indicated that under adiabatic conditions the initial exothermic temperature was 102.6 ℃,the maximum self-heating rate was 3.095×107 ℃·min-1,the maximum self-heating temperature was 375.9 ℃,and the pressure produced by unit mass was 4.512 MPa·g-1.Judged by ARC test,the emergency relief system for DTBP was a hybrid system.Based on Design Institute for Emergency Relief System(DIERS) method,the releasing mass flow rate W was determined by Leung methods,and the mass velocity G was calculated by two modified Omega methods.The two relief sizes calculated by monograph Omega method and arithmetic Omega method are close,with only 0.63% relative error.The monograph Omega method is more convenient to apply.

A CFD study on optimal venting volume and air flow distribution in a special designed hood system for controlling dust flow

A novel hood structure has been designed for the dust control system in the foundry in order to improve the working environment. A composite strategy has been applied for comparative analysis of the optimal venting volume and the airflow distribution between the conventional hood and the novel one in this study. A Computational Fluid Dynamic (CFD) method is used to simulate the airflow fields and dust-polluted air moving paths. The CFD results show that a two-outlet hood, with one outlet located on the left of the hood, is better for improving dust-polluted air than the hood with one outlet only. It can be concluded that the number of the outlets as well as their location on the hood has a significant influence on the air flow pattern in the hood. The optimal venting volume is also a major consideration that is discussed in the study. The venting volume should be designed by considering both the effective level of air flow velocity around the dust source and the energy saving. The optimal airflow distribution may reduce the turbulence in the hood system.

Mechanical properties of irradiated multi-phase polycrystalline BCC materials

Structure materials under severe irradiations in nuclear environments are known to degrade because of irradiation hardening and loss of ductility,resulting from irradiation-induced defects such as vacancies,interstitials and dislocation loops,etc.In this paper,we develop an elastic-viscoplastic model for irradiated multi-phase polycrystalline BCC materials in which the mechanical behaviors of individual grains and polycrystalline aggregates are both explored.At the microscopic grain scale,we use the internal variable model and propose a new tensorial damage descriptor to represent the geometry character of the defect loop,which facilitates the analysis of the defect loop evolutions and dislocation-defect interactions.At the macroscopic polycrystal scale,the self-consistent scheme is extended to consider the multiphase problem and used to bridge the individual grain behavior to polycrystal properties.Based on the proposed model,we found that the work-hardening coefficient decreases with the increase of irradiation-induced defect loops,and the orientation/loading dependence of mechanical properties is mainly attributed to the different Schmid factors.At the polycrystalline scale,numerical results for pure Fe match well with the irradiation experiment data.The model is further extended to predict the hardening effect of dispersoids in oxide-dispersed strengthened steels by the considering the Orowan bowing.The influences of grain size and irradiation are found to compete to dominate the strengthening behaviors of materials.

MULTI-SCALE AND MULTI-PHASE NANOCOMPOSITE CERAMIC TOOLS AND CUTTING PERFORMANCE

An advanced ceramic cutting tool material Al2O3/TiC/TiN （LTN） is developed by incorporation and dispersion of micro-scale TiC particle and nano-scale TiN particle in alumina matrix. With the optimal dispersing and fabricating technology, this multi-scale and multi-phase nanocomposite ceramic tool material can get both higher flexural strength and fracture toughness than that of A1203/TiC （LZ） ceramic tool material without nano-scale TiN particle, especially the fracture toughness can reach to 7.8 MPa . m^0.5. The nano-scale TiN can lead to the grain fining effect and promote the sintering process to get a higher density. The coexisting transgranular and intergranular fracture mode induced by micro-scale TiC and nano-scale TiN, and the homogeneous and densified microstructure can result in a remarkable strengthening and toughening effect. The cutting performance and wear mechanisms of the advanced multi-scale and multi-phase nanocomposite ceramic cutting tool are researched.

Left Ventricular Pseudoaneurysm Caused by a Left Ventricular Venting Catheter via the Right Superior Pulmonary Vein during Thoracic Aortic Surgery: A Case Report

A left ventricular (LV) pseudoaneurysm is one of the complications of acute myocardial infarction. It is also reported after chest trauma, cardiac surgery, and endocarditis. We report a rare case of an LV pseudoaneurysm induced by an LV venting catheter through the right superior pulmonary vein during thoracic aortic surgery. A 77-year-old man was referred for surgical repair of a distal aortic arch aneurysm. He underwent total aortic arch reconstruction with the frozen elephant trunk technique. The early postoperative period was uneventful. Postoperative contrast computed tomography and transthoracic echocardiography (TTE) revealed a pseudoaneurysm with a narrow neck at the apex of the LV that had sub-clinically progressed. Because of the risk of spontaneous rupture, an urgent aneurysmectomy was performed via a repeat sternotomy. Under cardioplegic arrest, the pseudoaneurysm was opened and the small orifice, which communicated with the LV, was confirmed. No myocardial ischemic changes were observed around the orifice. The pseudoaneurysm was thought to be induced by endocardial laceration by the tip of the venting catheter. The pseudoaneurysm was closed by linear repair reinforced with felt strips. The patient recovered well and was discharged 18 days after the second surgery. TTE showed no recurrence of LV aneurysm at the last follow-up.

Experimental investigation of external explosion in the venting process

Experimental investigations were conducted on the process of combustion and explosion vent in a 200 mm (diame- ter)×400 mm (length) vertical cylindrical vessel. When CH4-air mixture gases were used and the vent diameter was 55 mm, conditions of Φ (equivalent ratio)=0.8, Φ=1.0 and Φ=1.3 and two ignition positions (at the cylinder center and bottom) were selected. The venting processes and the correlated factors are discussed in this paper.

Numerical simulation for separation of multi-phase immiscible fluids in porous media

Based on a lattice Boltzmann method and general principles of porous flow, a numerical technique is presented for analysing the separation of multi-phase immiscible fluids in porous media. The total body force acting on fluid particles is modified by axiding relative permeability in Nithiarasu＇s expression with an axiditional surface tension term. As a test of this model, we simulate the phase separation for the case of two immiscible fluids. The numerical results show that the two coupling relative permeability coefficients K12 and K21 have the same magnitude, so the linear flux-forcing relationships satisfy Onsager reciprocity. Phase separation phenomenon is shown with the time evolution of density distribution and bears a strong similarity to the results obtained from other numerical models and the flows in sands. At the same time, the dynamical rules in this model are local, therefore it can be run on massively parallel computers with well computational efficiency.

Microstructure design and feasibility of hot stamping for new generation high strength multi-phase steels

Optimization of microstructure for new generation advanced high strength steels(AHSS ) for automobiles was briefly reviewed.Two different heat treatments(quenching partitioning austempering/QPA and quenching partitioning tempering/QPT) have been investigated to obtain optimal microstructures,which are made up of martensite(hard phase),retained austenite(soft phase),and carbide or nano-bainite.Combination of hot stamping and newly developed heat treatments is discussed.

Simulation on venting process and valve opening control method for gas trunk pipelines

Determining the venting time of a gas trunk pipeline segment provides an important basis for formulating an emergency plan in the advent of unexpected accidents.As the natural gas venting process corresponds to the transient flow,it is necessary to establish a transient hydraulic-thermal simulation model in order to determine the venting time.In this paper,based on two kinds of venting scenarios in which there is only one venting point in the venting system of a gas trunk pipeline segment—namely,where the venting point is either at one of the two ends or at the junction of two gas trunk pipeline segments—transient hydraulic-thermal simulation models are established.The models consist of gas flow governing equations,the gas state equation,gas physical property equations,initial conditions,and appropriate boundary conditions.The implicit central difference method is used to discretize the gas flow partial differential equations,and the trust-region-dogleg algorithm is used to solve the equations corresponding to each time step,in order to dynamically simulate the whole venting process.The judgment condition for the end of the venting process is that the average pressure of gas trunk pipeline segment is less than 0.11 MPa(actual pressure).Comparing the simulation results of the proposed model with those of the OLGA software and real operational data,we find that the venting time error is less than 10%.On this basis,a venting valve opening control principle is proposed,which prevents the venting noise from exceeded the specified noise value(85 d B)in the venting design of domestic gas pipeline projects.The established calculation model for venting time(dynamic simulation model)for a gas trunk pipeline segment and the proposed opening control principle of venting valve provide reference for the optimal operation of gas pipeline venting systems.

Filtered Containment Venting： Reasons, Technology,Impact on Environment

The AREVA FCVS （filtered containment venting system） is a product family that minimizes the environmental impact incase of a severe accident in a nuclear power plant. It is based on a large-scale test and qualification program as well as on the design,licensing and installation of more than 80 projects worldwide. The product family provides flexibility regarding adaptation toaccident scenarios, applicable codes and standards, seismic design, supply chain, implementation and localization. AREVA has broadexperience in managing fleet supplies, successful licensing support and cooperation with original equipment manufacturers ofpressurized and boiling water reactors.

Numerical simulation of complex multi-phase fluid of casting process and its applications

The fluid of casting process is a typical kind of multi-phase flow. Actually, many casting phenomena have close relationship with the multi-phase flow, such as molten metal filling process, air entrapment, slag movement, venting process of die casting, gas escaping of lost foam casting and so on. Obviously, in order to analyze these phenomena accurately, numerical simulation of the multi-phase fluid is necessary. Unfortunately, so far, most of the commercial casting simulation systems do not have the ability of multi-phase flow modeling due to the difficulty in the multi-phase flow calculation. In the paper, Finite Different Method (FDM) technique was adopt to solve the multi-phase fluid model. And a simple object of the muiti-phase fluid was analyzed to obtain the fluid rates of the liquid phase and the entrapped air phase.

A New Method for Hydrocarbon Detection Based on Multi-phase Theory

The hydrocarbon detection techniques used currently are generally based on the theory of single-phase medium, but hydrocarbon reservoir mostly is multi-phase medium, therefore, multisolutions and uncertainties are existed in the result of hydrocarbon detection. This paper presents a fast way to detect hydrocarbon in accordance with BOIT theory and laboratory data. The technique called DHAF technique has been applied to several survey area and obtained good result where the coincidence rate for hydrocarbon detection is higher than other similar techniques. The method shows a good prospect of the application in hydrocarbon detecting at exploration stage and in reservoir monitoring at production stage.

A proposed NMR solution for multi-phase flow fluid detection

In the petroleum industry,detection of multi-phase fluid flow is very important in both surface and down-hole measurements.Accurate measurement of high rate of water or gas multi-phase flow has always been an academic and industrial focus.NMR is an efficient and accurate technique for the detection of fluids;it is widely used in the determination of fluid compositions and properties.This paper is aimed to quantitatively detect multi-phase flow in oil and gas wells and pipelines and to propose an innovative method for online nuclear magnetic resonance(NMR)detection.The online NMR data acquisition,processing and interpretation methods are proposed to fill the blank of traditional methods.A full-bore straight tube design without pressure drop,a Halbach magnet structure design with zero magnetic leakage outside the probe,a separate antenna structure design without flowing effects on NMR measurement and automatic control technology will achieve unattended operation.Through the innovation of this work,the application of NMR for the real-time and quantitative detection of multi-phase flow in oil and gas wells and pipelines can be implemented.

A new analytical model for thermal stresses in multi-phase materials and lifetime prediction methods

Based on the fundamental equations of the mechanics of solid continuum, the paper employs an analytical model for determination of elastic thermal stresses in isotropic continuum represented by periodically distributed spherical particles with different distributions in an infinite matrix, imaginarily divided into identical cells with dimensions equal to inter-particle distances, containing a central spherical particle with or without a spherical envelope on the particle surface. Consequently, the multi-particle-（envelope）- matrix system, as a model system regarding the analytical modelling, is applicable to four types of multi-phase materials. As functions of the particle volume fraction v, the inter-particle distances dl, d2, d3 along three mutually per- pendicular axes, and the particle and envelope radii, R1 and R2, respectively, the thermal stresses within the cell, are originated during a cooling process as a consequence of the difference in thermal expansion coefficients of phases rep- resented by the matrix, envelope and particle. Analytical-（experimental）-computational lifetime prediction methods for multi-phase materials are proposed, which can be used in engineering with appropriate values of parameters of real multi-phase materials.