Particle agglomeration and inhibition method in the fluidized pyrolysis reaction of waste resin

This work investigated the pyrolysis reaction of waste resin in a fluidized bed reactor.It was found that the pyrolysis-generated ash would adhere to the surface of ceramic particles,causing particle agglomeration and defluidization.Adding kaolin could effectively inhibit the particle agglomeration during the fluidized pyrolysis reaction through physical isolation and chemical reaction.On the one hand,kaolin could form a coating layer on the surface of ceramic particles to prevent the adhesion of organic ash generated by the pyrolysis of resin.On the other hand,when a sufficient amount of kaolin(-0.2%(mass))was added,the activated kaolin could fully contact with the Na+ ions generated by the pyrolysis of resin and react to form a high-melting aluminosilicate mineral(nepheline),which could reduce the formation of low-melting-point sodium sulfate and thereby avoid the agglomeration of ceramic particles.

Optimizing Household Wastes (Rice, Vegetables, and Fruit) as an Environmentally Friendly Electricity Generator

The high consumption of electricity and issues related to fossil energy have triggered an increase in energy prices and the scarcity of fossil resources.Consequently,many researchers are seeking alternative energy sources.One potential technology,the Microbial Fuel Cell(MFC)based on rice,vegetable,and fruit wastes,can convert chemical energy into electrical energy.This study aims to determine the potency of rice,vegetable,and fruit waste assisted by Cu/Mg electrodes as a generator of electricity.The method used was a laboratory experiment,including the following steps:electrode preparation,waste sample preparation,incubation of the waste samples,construction of a reactor using rice,vegetable,and fruit waste as a source of electricity,and testing.The tests included measuring electrical conductivity,electric current,voltage,current density,and power density.Based on the test results,the maximum current and voltage values for the fruit waste samples were 5.53 V and 11.5 mA,respectively,with a current density of 2.300 mA/cm^(2) and a power density of 12.719 mW/cm^(2).The results indicate the potential for a future development.The next step in development involves determining the optimum conditions for utilizing of rice,vegetable,and fruit waste.The results of the electrical conductivity test on rice,vegetable,and fruit waste samples were 1.51,2.88,and 3.98 mS,respectively,with the highest electrical conductivity value found in the fruit waste sample.

Bearing capacity of circular footings on multi-layered sand-waste tire shreds reinforced with geogrids

The presence of waste tires poses an environmental challenge as they occupy a significant amount of land and are expensive to dispose in landfills.However,reusing waste tires can address this issue when waste tires are used in geotechnical applications.To determine the viability of this approach,laboratoryscale tests were conducted to investigate load-bearing capacity of circular footings on sand-tire shred(STS)mixtures with shredded waste tire contents of 5%e15%by weight and three different widths of shreds.The investigation focused on analyzing the thickness of layers composed of STS mixtures,the soil cap,and the impact of geogrids on bearing capacity.The results indicate that a specific mixture of sand and tire shreds provides the highest footing-bearing capacity.In addition,the optimal shred content and size were found to be 10%by weight and 2 cm×10 cm,respectively.Furthermore,for a given tire shred width,a particular length provides the largest bearing capacity.The results agree well with that of previous research conducted by the first author and his colleagues in direct shear and California bearing ratio(CBR)tests.The primary finding of this research is that the use of two-layered STS mixtures reinforced by geogrids significantly enhances the bearing capacity.

Photocatalytic Degradation of Plastic Waste: Recent Progress and Future Perspectives

Microplastics are persistent anthropogenic pollutants that have become a global concern due to their widespread distribution and unfamiliar threat to the environment and living organisms. Conventional technologies are unable to fully decompose and mineralize plastic waste. Therefore, there is a need to develop an environmentally friendly, innovative and sustainable photocatalytic process that can destroy these wastes with much less energy and chemical consumption. In photocatalysis, various nanomaterials based on wide energy band gap semiconductors such as TiO2 and ZnO are used for the conversion of plastic contaminants into environmentally friendly compounds. In this work, the removal of plastic fragments by photocatalytic reactions using newly developed photocatalytic composites and the mechanism of photocatalytic degradation of microplastics are systematically investigated. In these degradation processes, sunlight or an artificial light source is used to activate the photocatalyst in the presence of oxygen.

Impact of Plastic Waste on the Human Health in Low-Income Countries: A Systematic Review

Background: Plastic pollution is the accumulation of waste composed of plastic and its derivatives all over the environment. Whether in the form of visible garbage or microparticles, as it slowly degrades, plastic pollution poses significant threats to terrestrial and aquatic habitats and the wildlife that call them home, whether through ingestion, entanglement or exposure to the chemicals contained in the material. Unfortunately, there is a lack of documentation on the impact of plastic waste on human health in low- and middle-income countries (LMICs). Methods: We searched five electronic databases (PubMed, Embase, Global Health, CINAHL and Web of Science) and gray literature, following the preferred reporting elements for systematic reviews and meta-analyses (PRISMA), for the impact of plastic waste on human health in developing countries. We included quantitative and qualitative studies written in English and French. We assessed the quality of the included articles using the Mixed Methods Appraisal tool (MMAT). Results: A total of 3779 articles were initially identified by searching electronic databases. After eliminating duplicates, 3167 articles were reviewed based on title and abstract, and 26 were selected for full-text review. Only three articles were retained. The three articles dealt with practices likely to lead to oral exposure to plastic chemicals in human health, as well as the level of awareness of participants concerning the possible impact of plastic on human health, namely, the use of plastic baby bottles, the use of microwaves to cook food and reheat precooked food, the use of plastic bottles to store water in the refrigerator, water purifier containers with plastic bodies and plastic lunch boxes, the reuse of plastic bags and the inadequacy of treatment facilities. Conclusion: Plastic waste poses different risks to human health at every stage of its life cycle. Hence, strategies must be adopted to raise public awareness of the dangers of plastic waste to their health. Trial registration: The review protocol is registered in the PROSPERO international prospective register of systematic reviews (ID = CRD42023409087).

Household Solid Waste Awareness and Practices among Residents of Windhoek, Namibia

This study explores household solid waste management (HSWM) practices and awareness among residents of Windhoek West, a rapidly urbanizing constituency in the Khomas Region of Namibia. Employing a descriptive methodology, the research investigates the interplay between public awareness, regulatory frameworks, and the availability of waste management facilities to assess their impact on waste management behaviors. Our findings indicate significant gaps in both knowledge and infrastructure that hinder effective waste management. The study reveals that while there is a high willingness among residents to engage in recycling and waste reduction, actual practices are limited due to inadequate facilities and lack of stringent enforcement of waste policies. This research identifies key factors that influence waste management practices, including demographic characteristics and access to waste management facilities. It also proposes actionable strategies such as expanding recycling and sorting facilities, enhancing educational campaigns tailored to local needs, and implementing regular enforcement mechanisms. These strategies are aimed at improving compliance with waste management protocols and fostering a culture of environmental responsibility. The results of this investigation show the critical role of ongoing education and infrastructural improvement in bridging existing knowledge gaps and facilitating effective waste management practices. This research lays a foundational step toward enhancing sustainable urban development and effective waste management in Windhoek, providing valuable insights for policymakers, community leaders, and stakeholders engaged in urban environmental management.

Study on synergistic leaching of potassium and phosphorus from potassium feldspar and solid waste phosphogypsum via coupling reactions

To achieve the resource utilization of solid waste phosphogypsum(PG)and tackle the problem of utilizing potassium feldspar(PF),a coupled synergistic process between PG and PF is proposed in this paper.The study investigates the features of P and F in PG,and explores the decomposition of PF using hydrofluoric acid(HF)in the sulfuric acid system for K leaching and leaching of P and F in PG.The impact factors such as sulfuric acid concentration,reaction temperature,reaction time,material ratio(PG/PF),liquid–solid ratio,PF particle size,and PF calcination temperature on the leaching of P and K is systematically investigated in this paper.The results show that under optimal conditions,the leaching rate of K and P reach more than 93%and 96%,respectively.Kinetics study using shrinking core model(SCM)indicates two significant stages with internal diffusion predominantly controlling the leaching of K.The apparent activation energies of these two stages are 11.92 kJ·mol^(-1)and 11.55 kJ·mol^(-1),respectively.

Synergetic Bioproduction of Short-Chain Fatty Acids from Waste Activated Sludge Intensified by the Combined Use of Potassium Ferrate and Biosurfactants

The synergetic effect and underlying mechanism of potassium ferrate(PF)with tea saponin(TS,a biosurfactant)in producing short chain fatty acids(SCFAs)from anaerobic fermentation of waste activated sludge(WAS)were explored in this work.Experimental results showed that 0.2 g PF(g TSS)^(-1)(total suspended solid)combined with 0.02 g TS(g TSS)^(-1) could further improve SCFAs’production,and the maximum SCFAs content reached 2008.7 mg COD L^(-1),which is 1.2 and 4.5 times higher than those with PF and TS individually added,respectively,and 5.3 times higher than that of blank WAS on Day 12.In the model substrates experiments,the degradation rates of bovine serum albumin and dextran with combination of PF and TS were 41.3%±0.1% and 48.5%±0.06%,respectively,on Day 3,which are lower than those in blank WAS(with degradation rates of 72.3%±0.5%and 90.3%±0.3%).It was revealed that the oxidative effect of PF and the solubilization of TS caused more organic matters to be dissolved out from WAS,providing a large number of biodegradable substances for subsequent SCFAs production.While WAS pretreated with the combination of PF and TS,the relative abundances of Firmicutes increased from 6.4%(blank)to 38.6%,and that of Proteobacteria decreased from 41.8%(blank)to 21.8%.The combination of PF and TS promoted the hydrolysis process of WAS by enriching Firmicutes,and then increased acetic acid production by inhibiting Proteobacteria that consumed SCFAs.Meanwhile,at the genus level,acidogenesis bacteria(e.g.,Proteiniclasticum and Petrimonas)were enriched whereas SCFAs consuming bacteria(e.g.,Dokdonella)were inhibited.

Efficient and rapid capture of uranium(Ⅵ) in wastewater via multiamine modified β-cyclodextrin porous polymer

It is quite important to ensure the safety and sustainable development of nuclear energy for the treatment of radioactive wastewater. To treat radioactive wastewater efficiently and rapidly, two multi-amine β-cyclodextrin polymers(diethylenetriamine β-cyclodextrin polymer(DETA-TFCDP) and triethylenetetramine β-cyclodextrin polymer(TETA-TFCDP)) were prepared and applied to capture uranium. Results exhibited that DETA-TFCDP and TETA-TFCDP displayed the advantages of high adsorption amounts(612.2and 628.2 mg·g-1, respectively) and rapid adsorption rates, which can reach(88 ± 1)% of their equilibrium adsorption amounts in 10 min. Moreover, the adsorbent processes of DETA-TFCDP and TETATFCDP on uranium(Ⅵ) followed the Langmuir model and pseudo-second-order model, stating they were mainly chemisorption and self-endothermic. Besides, TETA-TFCDP also showed excellent selectivity in the presence of seven competing cations and could be effectively reused five times via Na2CO3as the desorption reagent. Meanwhile, X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy illustrated that the enriched multi-amine groups and oxygen-containing functional groups on the surface of TETA-TFCDP were the main active sites for capturing uranium(Ⅵ). Hence, multi-amine β-cyclodextrin polymers are a highly efficient, rapid, and promising adsorbent for capturing uranium(Ⅵ)from radioactive wastewater.

Performance and Emission Characteristics of a CRDI Diesel Engine Fuelled by SiO_(2) Nanoparticle-Waste Fat Biodiesel Blends

This study investigates the use of waste fat biodiesel(WFB)from the leather industry as a substitute for diesel fuel.Specifically,it examines the diesel engine performance of WFB,a blend of WFB and diesel(B50),and different blends of WFB and silicon dioxide(SiO_(2))nanoparticles(B50SiO_(2)40,B50SiO_(2)80,and B50SiO_(2)120μg/g).The results indicate that the B50SiO_(2)120 blend increases brake thermal efficiency by 10.03%compared to pure biodiesel but falls 1.93%short of neat diesel.Furthermore,the B50SiO_(2)120 mixture reduces smoke,hydrocarbon,and carbon monoxide emissions by 31.87%,34.14%,and 43.97%respectively,compared to diesel.However,the B50SiO_(2)120 blend shows a 4.91%increase in nitrogen oxide emissions compared to diesel.

Waste Cotton-Derived Fiber-Based Thermoelectric Aerogel for Wearable and Self-Powered Temperature-Compression Strain Dual-Parameter Sensing

The rapid development of the global economy and population growth are accompanied by the production of numerous waste textiles.This leads to a waste of limited resources and serious environmental pollution problems caused by improper disposal.The rational recycling of wasted textiles and their transformation into high-value-added emerging products,such as smart wearable devices,is fascinating.Here,we propose a novel roadmap for turning waste cotton fabrics into three-dimensional elastic fiber-based thermoelectric aerogels by a one-step lyophilization process with decoupled self-powered temperature-compression strain dual-parameter sensing properties.The thermoelectric aerogel exhibits a fast compression response time of 0.2 s,a relatively high Seebeck coefficient of 43μV·K^(-1),and an ultralow thermal conductivity of less than 0.04 W·m^(-1)·K^(-1).The cross-linking of trimethoxy(methyl)silane(MTMS)and cellulose endowed the aerogel with excellent elasticity,allowing it to be used as a compressive strain sensor for guessing games and facial expression recognition.In addition,based on the thermoelectric effect,the aerogel can perform temperature detection and differentiation in self-powered mode with the output thermal voltage as the stimulus signal.Furthermore,the wearable system,prepared by connecting the aerogel-prepared array device with a wireless transmission module,allows for temperature alerts in a mobile phone application without signal interference due to the compressive strains generated during gripping.Hence,our strategy is significant for reducing global environmental pollution and provides a revelatory path for transforming waste textiles into high-value-added smart wearable devices.

Utilization of recycled solid waste as ecological reclamation materials based on plant growth experiments and soil quality analysis

During the highway construction,a large number of spoil areas will be generated while a large amount of waste slag and soil could not be rationally utilized.Besides,the vegetation recovery is slow in the spoil areas due to the soil depletion.Aiming at recycling the solid waste,the sieved engineering waste slag with local red clay and corn straw biochar was supplied to solve the problem of insufficient nutrients in engineering waste slag and soil.In addition,planting experiments of alfalfa(Medicago sativa L.)and Amorpha fruticosa L.combined with physical and chemical experiments were carried out to prove the feasibility of the novel improved substrate for the reclamation of spoil areas.The results show that the substrate's improvement effect is mainly affected by the soil to slag ratio and the biochar content.The improvement effect of soil matrix in highway spoil area decreases with the increase of the waste slag content,especially when the soil-slag ratio is less than 3,and the promotion of plants is limited.On the contrary,the improvement effect is proportional to the biochar content(3%-8%).But it is noted that the Cu and Pb in the soil will exceed the clean limit corresponding to the Nemero soil pollution index level when the biochar content is 8%.Therefore,it is recommended that the soil-slag ratio should be≥3,and the biochar content should reach 3%-5%.This research provides experimental basis and technical support for utilizing solid waste resources in the reclamation of highway spoil areas.

Bird’s-eye view of recycled solid wastes in road engineering

Recent trends in road engineering have explored the potential of incorporating recycled solid wastes into infrastructures that including pavements,bridges,tunnels,and accessory structures.The utilization of solid wastes is expected to offer sustainable solutions to waste recycling while enhancing the performance of roads.This review provides an extensive analysis of the recycling of three main types of solid wastes for road engineering purposes:industrial solid waste,infrastructure solid waste,and municipal life solid waste.Industrial solid wastes suitable for road engineering generally include coal gangue,fly ash,blast furnace slag,silica fume,and steel slag,etc.Infrastructure solid wastes recycled in road engineering primarily consist of construction&demolition waste,reclaimed asphalt pavements,and recycled cement concrete.Furthermore,recent exploration has extended to the utilization of municipal life solid wastes,such as incinerated bottom ash,glass waste,electronics waste,plastic waste,and rubber waste in road engineering applications.These recycled solid wastes are categorized into solid waste aggregates,solid waste cements,and solid waste fillers,each playing distinct roles in road infrastructure.Roles of solid waste acting aggregates,cements,and fillers in road infrastructures were fully investigated,including their pozzolanic properties,integration effects to virgin materials,modification or enhancement solutions,engineering performances.Utilization of these materials not only addresses the challenge of waste management but also offers environmental benefits aiming carbon neutral and contributes to sustainable infrastructure development.However,challenges such as variability in material properties,environmental impact mitigation,secondary pollution to environment by leaching,and concerns regarding long-term performance need to be further addressed.Despite these challenges,the recycled solid wastes hold immense potential in revolutionizing road construction practices and fostering environmental stewardship.This review delves into a bird’seye view of the utilization of recycled solid wastes in road engineering,highlighting advances,benefits,challenges,and future prospects.

Mixed plastics waste valorization to high-added value products via thermally induced phase separation and spin-casting

Plastic waste is an underutilized resource that has the potential to be transformed into value-added materials.However,its chemical diversity leads to cost-intensive sorting techniques,limiting recycling and upcycling opportunities.Herein,we report an open-loop recycling method to produce graded feedstock from mixed polyolefins waste,which makes up 60%of total plastic waste.The method uses heat flow scanning to quantify the composition of plastic waste and resolves its compatibility through controlled dissolution.The resulting feedstock is then used to synthesize blended pellets,porous sorbents,and superhydrophobic coatings via thermally induced phase separation and spin-casting.The hybrid approach broadens the opportunities for reusing plastic waste,which is a step towards creating a more circular economy and better waste management practices.

Discussion on“Dispersion characteristics of clayey soils containing waste rubber particles”[J Rock Mech Geotech Eng 15(2023)3050e3058]

We read with great interest the recent article by Erenson(2023)entitled“Dispersion characteristics of clayey soils containing waste rubber particles”.The author has studied the dispersion characteristics of clayey soils containing different percentages of waste rubber particles(WRPs)by performing several tests(viz.consistency limit,linear shrinkage limit,double hydrometer,crumb test and pinhole test)and scanning electron microscopy(SEM)analysis on five clayey(viz.Na-activated bentonite,refined ball clay,Ukrainian kaolin,Avanos kaolin and Afyon clay)samples containing 0%,5%,10%and 15%WRPs.It should be noted that Erenson(2023)has presented some interesting observations,but there are some serious issues that we want to share through this discussion and request the author of the original paper to address them to avoid their persistence in the scientific literature.

MXene Enhanced 3D Needled Waste Denim Felt for High‑Performance Flexible Supercapacitors

MXene,a transition metal carbide/nitride,has been prominent as an ideal electrochemical active material for supercapacitors.However,the low MXene load limits its practical applications.As environmental concerns and sustainable development become more widely recognized,it is necessary to explore a greener and cleaner technology to recycle textile by-products such as cotton.The present study proposes an effective 3D fabrication method that uses MXene to fabricate waste denim felt into ultralight and flexible supercapacitors through needling and carbonization.The 3D structure provided more sites for loading MXene onto Z-directional fiber bundles,resulting in more efficient ion exchange between the electrolyte and electrodes.Furthermore,the carbonization process removed the specific adverse groups in MXenes,further improving the specific capacitance,energy density,power density and electrical conductivity of supercapacitors.The electrodes achieve a maximum specific capacitance of 1748.5 mF cm-2 and demonstrate remarkable cycling stability maintaining more than 94%after 15,000 galvanostatic charge/discharge cycles.Besides,the obtained supercapacitors present a maximum specific capacitance of 577.5 mF cm^(-2),energy density of 80.2μWh cm^(-2)and power density of 3 mW cm^(-2),respectively.The resulting supercapacitors can be used to develop smart wearable power devices such as smartwatches,laying the foundation for a novel strategy of utilizing waste cotton in a high-quality manner.

Sustainable Management of Biodegradable Waste in Guinea: Effect of Compost on Eggplant and Chilli Crop Yields Pepper

The fight against insalubrity in large urban and peri-urban agglomerations is a major challenge in developing countries. This problem is compounded by that of sustainable waste management mechanisms. Indeed, the current waste collection system in Guinea has proved inadequate, as moving garbage from point “A” to point “B” is tantamount to “moving the problem”. The aim of this experimental work is to demonstrate the cost-effectiveness and benefits of sustainable waste management. As part of this drive to valorize biodegradable waste, the Waste Management Research Center has undertaken a series of activities ranging from composting organic waste to testing compost on certain crop varieties. An experimental field of 8024 m2 was laid out and treated with 1500 Kg of fine compost in doses ranging from 2.5 to 5 T/ha. Two crop varieties, eggplant and chili, were tested. Compost application increased production yields: 15 to 21 tonnes of eggplant and 10.4 to 11.1 tonnes of chili per hectare. Growth rates compared with usual yields varied from 50% to 64% and from 11% to 17% for eggplant and chili, respectively. This study resulted in an optimum compost dose of 2.5 T/ha for this phase.

Levels of Polycyclic Aromatic Hydrocarbons (PAHs) in Healthcare Waste Incinerators’ Bottom Ash from Five County Hospitals in Kenya

Health-care waste contains potentially harmful microorganisms and compounds which can infect and affect hospital patients, healthcare workers, the general public and environment. Therefore, management of health care waste requires safe handling, treatment and disposal procedures. While incineration reduces the volume and quantity of waste for final disposal, it leads to the production of fly and bottom ashes laden with toxic incomplete combustion products such as Polycyclic Aromatic Hydrocarbons (PAHs), dioxins, furans and heavy metals. This exposes workers who handle and dispose the bottom ashes, hospital patients, the general public and environment. The goal of this study was to determine the total and individual levels of 16 most prevalent and toxic PAHs. Bottom ash samples were collected from incinerators in five county hospitals in Kenya, namely;Moi-Voi, Narok, Kitale, Makindu and Isiolo. Bottom ash samples were collected over a period of six months from the five hospitals. The samples were then sieved, homogenised and stored at 4°C in amber coloured glass containers. The PAHs were extracted using 30 ml of a hexane-acetone solvent (1:1) mixture by ultrasonication at room temperature (23°C) for 45 minutes. The PAHs were then analyzed with a GC-MS spectrophotometer model (Shimadzu GCMS-QP2010 SE) connected to a computer work station was used for the PAHs analysis. The GC-MS was equipped with an SGE BPX5 GC capillary column (30 m × 0.25 mm × 0.25 μm) for the separation of compounds. Helium was used as the carrier gas at a flow rate of 15.5 ml/minute and 14.5 psi. 1 μl of the sample was injected at 280°C, split mode (10:1). The oven programming was set for a total runtime of 40 minutes, which included: 100°C (2-minute hold);10°C /min rise to 200°C;7°C /min rise to 249°C;3°C /min rise to 300°C (2-minute hold). The interface temperature was set at 290°C. Analysis was done in Selected Ion Monitoring (SIM) mode and the peak areas of each of the PAHs were collected from the chromatograph and used for quantification of the 16 PAHs listed by the U.S. Environmental Protection Agency (EPA) which included, BaA (benz[a]anthracene: 4 rings), BaP (benzo[a]pyrene: 5 rings), BbF (benzo [b]fluoranthene: 5 rings), BkF (benzo[k]fluoranthene: 5 rings), Chr (chrysene: 4 rings), DbA (dibenz[a,h]anthracene: 5 rings), InP (indeno[1,2,3 - cd] pyrene: 6 rings) and Acp (acenaphthene: 3 rings), Acpy (acenaphthylene: 3 rings), Ant (anthracene: 3 rings), BghiP (benzo[g,h,i]perylene: 6 rings), Flu (fluorene: 3 rings), FluA (fluoranthene: 4 rings), Nap (naphthalene: 2 rings), PhA (phenanthrene: 3 rings) and Pyr (pyrene: 4 rings). Ion source-interface temperature was set at 200°C - 250°C. Internal standards from Sigma Aldrich were used in the analysis and the acquired mass spectra data were then matched against the NIST 2014 library [1] [2]. The mean PAHs concentration in the bottom ashes of each hospital varied broadly from 0.001 mg/kg to 0.4845 mg/kg, and the mean total concentration levels of individual PAHs ranged from 0.0072 mg/kg to 1.171 mg/kg. Low molecular weight PAHs (Phenanthrene, Naphthalene and Fluorene) were predominant in all the hospital wastes whereas Kitale and Narok presented the lowest PAHs concentrations and the lowest number of individual PAHs. Moi/Voi recorded the highest total PAHs concentration at 1.3129 ± 0.0023 mg/kg from a total of 11 PAHs being detected from the bottom ash samples. Narok had only three PAHs being detected at very low concentrations of 0.0041 ± 0.00 mg/kg, 0.0076 ± 0.00 mg/kg and 0.012 ± 0.00 mg/kg for phenanthrene, anthracene and chrysene respectively. This study presents hospital incinerator bottom ash as containing detectable levels of both carcinogenic and non-carcinogenic PAHs. Continued unprotected exposure of hospital workers (waste handlers) to the bottom ash PAHs could be hazardous to their health because of their cumulative effect. Preventive measures e.g. the use of Personal protective equipment (PPE) should be prioritised to minimise direct contact with the bottom ash. The study recommends an upgrade on incinerator technology for efficient combustion processes thus for better pollution control.

Multi-Component Resource Recycling from Waste Light-Emitting Diode Under Hydrothermal Condition:Plastic Package Degradation,Speciation of Nano-TiO_(2),and Environmental Impact Assessment

Light emitting diodes(LEDs)have accounted for most of the lighting market as the technology matures and costs continue to reduce.As a new type of e-waste,LED is a double-edged sword,as it contains not only precious and rare metals but also organic packaging materials.In previous studies,LED recycling focused on recovering precious and strategic metals while ignoring harmful substances such as organic packaging materials.Unlike crushing and other traditional methods,hydrothermal treatment can provide an environment-friendly process for decomposing packaging materials.This work developed a closed reaction vessel,where the degradation rate of plastic polyphthalamide(PPA)was close to 100%,with nano-TiO_(2)encapsulated in plastic PPA being efficiently recovered,while metals contained in LED were also recycled efficiently.Besides,the role of water in plastic PPA degradation that has been overlooked in current studies was explored and speculated in detail in this work.Environmental impact assessment revealed that the proposed recycling route for waste LED could significantly reduce the overall environmental impact compared to the currently published processes.Especially the developed method could reduce more than half the impact of global warming.Furthermore,this research provides a theoretical basis and a promising method for recycling other plastic-packaged e-waste devices,such as integrated circuits.

Correlation between hardness and SEM-EDS characterization of palm oil waste based biocoke

This research investigates the relationship between hardness and microstructure obtained through SEM-EDS analysis of palm oil waste-based biocoke.The mechanical qualities and chemical composition of biocoke are being studied concerning the influence of temperature conditions.The manufacturing temperature of biocoke may vary between 150℃ and 190℃.Utilizing SEM-EDS,we were able to characterize the microstructure and analyze the elemental composition,while the Hardness Shore D approach was used for the most complex materials.These results highlight the possibility of optimizing production temperature to produce biocoke with better mechanical performance.They show a positive correlation between biocoke hardness and structured carbon content.At 150℃ and 180℃,respectively,the EFB biocoke reached its maximum hardness level of 62±5.At 190℃,OPM biocoke generated a 60±5 times greater hardness than that of OPM and OPF biocoke.The OPT biocoke sample had the highest porosity with a score of 0.86,or 85.76%.Furthermore,compared to EFB biocoke,OPM and OPF biocokes had a priority of 0.84(84.20%)and 0.83(83.48%),respectively.Biocoke hardness is a quality indicator of physical and chemical qualities;the vital link between biocoke hardness,structural features,and elemental composition supports this idea.