A novel approach for analyzing coupled vibrations between vehicles and bridges is presented,taking into account spatiotemporal effects and mechanical phenomena resulting fromvehicle braking.Efficient modeling and solu...A novel approach for analyzing coupled vibrations between vehicles and bridges is presented,taking into account spatiotemporal effects and mechanical phenomena resulting fromvehicle braking.Efficient modeling and solution of bridge vibrations induced by vehicle deceleration are realized using this method.The method’s validity and reliability are substantiated through numerical examples.A simply supported beam bridge with a corrugated steel web is taken as an example and the effects of parameters such as the initial vehicle speed,braking acceleration,braking location,and road surface roughness on the mid-span displacement and impact factor of the bridge are analyzed.The results show that vehicle braking significantly amplifies mid-span displacement and impact factor responses in comparison to uniform vehicular motion across the bridge.Notably,the influence of wheelto-bridge friction forces is of particular significance and cannot be overlooked.When the vehicle initiates braking near the middle of the span,both the mid-span displacement and impact factor of the bridge exhibit substantial increases,further escalating with higher braking acceleration.Under favorable road surface conditions,the midspan displacement and the impact factor during vehicle braking may exceed the design values stipulated by codes.It is important to note that road surface roughness exerts a more pronounced effect on the impact factor of the bridge in comparison to the effects of vehicle braking.展开更多
Ultrasonic vibration-assisted grinding(UVAG)is an effective and promising method for machining of hard-to-cut materials.This article proposed an ultrasonic vibration plate device enabling the longitudinal full-wave an...Ultrasonic vibration-assisted grinding(UVAG)is an effective and promising method for machining of hard-to-cut materials.This article proposed an ultrasonic vibration plate device enabling the longitudinal full-wave and transverse half-wave(L2T1)vibration mode for UVAG.The characteristics of two-dimensional coupled vibration in different directions were analyzed on the basis of apparent elastic method and finite element method.Furthermore,a correction factor was applied to correct the frequency error caused by the apparent elastic method.Finally,the comparative experiments between the conventional creep-feed grinding and UVAG of Inconel 718 nickel-based superalloy were carried out.The results indicate that the apparent elastic method with the correction factor is accurate for the design of plate device under the L2T1 vibration mode.Compared with the conventional creep-feed grinding,the UVAG causes the reduction of grinding force and the improvement of machined surface quality of Inconel 718 nickel-based superalloy.Furthermore,under the current experimental conditions,the optimal ultrasonic vibration amplitude is determined as 6μm,with which the minimum surface roughness is achieved.展开更多
The vibration of a Francis turbine is analyzed with the additional quality matrix method based on fluid-structure coupling (FSC). Firstly, the vibration frequency and mode of blade and runner in air and water are ca...The vibration of a Francis turbine is analyzed with the additional quality matrix method based on fluid-structure coupling (FSC). Firstly, the vibration frequency and mode of blade and runner in air and water are calculated. Secondly, the influences to runner frequency domain by large flow, small flow and design flow working conditions are compared. Finally the influences to runner modes by centrifugal forces under three rotating speeds of 400 r/rain, 500 r/min and 600 r/rain are compared. The centrifugal force and small flow working condition have greatly influence on the vibration of small runner. With the increase of centrifugal force, the vibration frequency of the runner is sharply increased. Some order frequencies are even close to the runner natural frequency in the air. Because the low frequency vibration will severely damage the stability of the turbine, low frequency vibration of units should be avoided as soon as possible.展开更多
By applying the sinusoidal wave mode to simulate the rugged surface of bridge deck,accounting for vehicle-bridge interaction and using Euler-Bernoulli beam theory, a coupling vibration model of vehicle-bridge system w...By applying the sinusoidal wave mode to simulate the rugged surface of bridge deck,accounting for vehicle-bridge interaction and using Euler-Bernoulli beam theory, a coupling vibration model of vehicle-bridge system was developed. The model was solved by mode analyzing method and Runge-Kutta method, and the dynamic response and the resonance curve of the bridge were obtained. It is found that there are two resonance regions, one represents the main resonance while the other the minor resonance, in the resonance curve. The influence due to the rugged surface, the vibration mode of bridge, and the interaction between vehicle and bridge on vibration of the system were discussed. Numerical results show that the influence due to these parameters is so significant that the effect of roughness of the bridge deck and the mode shape of the bridge can't be ignored and the vehicle velocity should be kept away from the critical speed of the vehicle.展开更多
The governing equation and energy equations for thermal-elastic coupling vibration of cylindrical shell were developed. The Garlerkin method was used in numerical process. Some useful result can be concluded from nume...The governing equation and energy equations for thermal-elastic coupling vibration of cylindrical shell were developed. The Garlerkin method was used in numerical process. Some useful result can be concluded from numerical result. With the increase of the amplitude of temperature and coupling coefficient, the speed of vibration decaying becomes slower and the coupling effect becomes weaker. The larger the ration of length to radius and length to thickness, the faster the decaying of the vibration amplitude and the vibration frequency increase. It means the coupling effect gets stronger. The larger the coupling coefficient, the smaller the axial stress, the axial force and the bendind moment are.展开更多
In recent years,high-speed railways in China have developed very rapidly,and the number and span of the railway bridges are keeping increasing.Meanwhile,frequent extreme disasters,such as strong winds,earthquakes and ...In recent years,high-speed railways in China have developed very rapidly,and the number and span of the railway bridges are keeping increasing.Meanwhile,frequent extreme disasters,such as strong winds,earthquakes and floods,pose a significant threat to the safety of the train–bridge systems.Therefore,it is of paramount importance to evaluate the safety and comfort of trains when crossing a bridge under external excitations.In these aspects,there is abundant research but lacks a literature review.Therefore,this paper provides a comprehensive state-of-the-art review of research works on train–bridge systems under external excitations,which includes crosswinds,waves,collision loads and seismic loads.The characteristics of external excitations,the models of the train–bridge systems under external excitations,and the representative research results are summarized and analyzed.Finally,some suggestions for further research of the coupling vibration of train–bridge system under external excitations are presented.展开更多
Considering the axial and radial loads, a math- ematical model of angular contact ball bearing is deduced with Hertz contact theory. With the coupling effects of lateral, torsional and axial vibrations taken into acco...Considering the axial and radial loads, a math- ematical model of angular contact ball bearing is deduced with Hertz contact theory. With the coupling effects of lateral, torsional and axial vibrations taken into account, a lumped-parameter nonlinear dynamic model of helical gearrotor-bearing system (HGRBS) is established to obtain the transmission system dynamic response to the changes of dif- ferent parameters. The vibration differential equations of the drive system are derived through the Lagrange equation, which considers the kinetic and potential energies, the dis- sipative function and the internal/external excitation. Based on the Runge-Kutta numerical method, the dynamics of the HGRBS is investigated, which describes vibration properties of HGRBS more comprehensively. The results show that the vibration amplitudes have obvious fluctuation, and the frequency multiplication and random frequency components become increasingly obvious with changing rotational speed and eccentricity at gear and bearing positions. Axial vibration of the HGRBS also has some fluctuations. The bearing has self-variable stiffness frequency, which should be avoided in engineering design. In addition, the bearing clearance needs little attention due to its slightly discernible effect on vibration response. It is suggested that a careful examination should be made in modelling the nonlinear dynamic behavior of a helical gear-rotor-bearing system.展开更多
The influence of pavement vibration on tire adhesion is of great significance to the structure design of vehicle and pavement.The adhesion between tire and road is the key to studying vehicle dynamics,and the precise ...The influence of pavement vibration on tire adhesion is of great significance to the structure design of vehicle and pavement.The adhesion between tire and road is the key to studying vehicle dynamics,and the precise description of tire adhesion affects the accuracy of dynamic vehicle responses.However,in most models,only road roughness is considered,and the pavement vibration caused by vehicle-road interaction is ignored.In this paper,a vehicle is simplified as a spring-mass-damper oscillator,and the vehicle-pavement system is modeled as a vehicle moving along an Euler-Bernoulli beam with finite length on a nonlinear foundation.The road roughness is considered as a sine wave,and the shear stress is ignored on the pavement.According to the contact form between tire and road,the LuGre tire model is established to calculate the tire adhesion force.The Galerkin method is used to simplify the partial differential equations of beam vibration into finite ordinary differential equations.A product-to-sum formula and a Dirac delt function are used to deal with the nonlinear term caused by the nonlinear foundation,which realizes the fast and accurate calculation of super-high dimensional nonlinear ordinary differential equations.In addition,the dynamic responses between the coupled system and the traditional uncoupled system are compared with each other.The obtained results provide an important theoretical basis for research on the influence of vehicle-road coupled vibration on tire adhesion.展开更多
On the basis of the traditional mechanical model of a grinding wheel rotor and the mechanical-electric coupling model with ideal sinusoidal supply, taking high-frequency converting current of inverter power switches i...On the basis of the traditional mechanical model of a grinding wheel rotor and the mechanical-electric coupling model with ideal sinusoidal supply, taking high-frequency converting current of inverter power switches into further consideration, a modified mechanical-electric coupling model is created. The created model consists of an inverter, a motorized spindle, a grinding wheel and grinding loads. Some typical non-stationary processes of the grinding system with two different supplies, including the starting, the speed rising and the break in grinding loads, are compared by making use of the created model. One supply is an ideal sinusoidal voltage source, the other is an inverter. The theoretical analysis of the high-order harmonic is also compared with the experimental result. The material strategy of suppressing high-order harmonic mechanical-electric coupling vibration by optimizing inverter operating parameters is proposed.展开更多
The modal method is applied to analyze coupled vibration of belt drive systems. A belt drive system is a hybrid system consisting of continuous belts modeled as strings as well as discrete pulleys and a tensioner arm....The modal method is applied to analyze coupled vibration of belt drive systems. A belt drive system is a hybrid system consisting of continuous belts modeled as strings as well as discrete pulleys and a tensioner arm. The characteristic equation of the system is derived from the governing equation. Numerical results demenstrate the effects of the transport speed and the initial tension on natural frequencies.展开更多
Zero mode natural frequency (ZMNF) is found during experiments. The ZMNF andvibrations resulted by it are studied. First, calculating method of the ZMNF excited byelectromagnetic in vibrational system of coupled mecha...Zero mode natural frequency (ZMNF) is found during experiments. The ZMNF andvibrations resulted by it are studied. First, calculating method of the ZMNF excited byelectromagnetic in vibrational system of coupled mechanics and electrics are given from the view ofmagnetic energy. Laws that the ZMNF varies with active power and exciting current are obtained andare verified by experiments. Then, coupled lateral and torsional vibration of rotor shaft system isstudied by considering rest eccentricity, rotating eccentricity and swing eccentricity. UsingLargrange-Maxwell equation when three phases are asymmetric derives differential equation of thecoupled vibration. With energy method of nonlinear vibration, amplitude-frequency characteristics ofresonance are studied when rotating speed of rotor equals to ZMNF. The results show that ZMNF willoccur in turbine generators by the action of electromagnetic. Because ZMNF varies withelectromagnetic parameters, resonance can occur when exciting frequency of the rotor speed is fixedwhereas exciting current change. And also find that a generator is in the state of large amplitudein rated exciting current.展开更多
Based on the theory of composite materials and phononic crystals(PCs),a large-size rectangular piezoelectric composite plate with the quasi-periodic PC structure composed of PZT-4 and epoxy is proposed in this paper.T...Based on the theory of composite materials and phononic crystals(PCs),a large-size rectangular piezoelectric composite plate with the quasi-periodic PC structure composed of PZT-4 and epoxy is proposed in this paper.This PC structure can suppress the transverse vibration of the piezoelectric composite plate so that the thickness mode is purer and the thickness vibration amplitude is more uniform.Firstly,the vibration of the model is analyzed theoretically,the electromechanical equivalent circuit diagram of three-dimensional coupled vibration is established,and the resonance frequency equation is derived.The effects of the length,width,and thickness of the piezoelectric composite plate at the resonant frequency are obtained by the analytical method and the finite element method,the effective electromechanical coupling coefficient is also analyzed.The results show that the resonant frequency can be changed regularly and the electromechanical conversion can be improved by adjusting the size of the rectangular piezoelectric plate.The effect of the volume fraction of the scatterer on the resonant frequency in the thickness direction is studied by the finite element method.The band gap in X and Y directions of large-size rectangular piezoelectric plate with quasi-periodic PC structures are calculated.The results show that the theoretical results are in good agreement with the simulation results.When the resonance frequency is in the band gap,the decoupling phenomenon occurs,and then the vibration mode in the thickness direction is purer.展开更多
In the present study,the dynamic response of block foundations of different equivalent radius to mass(R;/m) ratios under coupled vibrations is investigated for various homogeneous and layered systems.The frequency-d...In the present study,the dynamic response of block foundations of different equivalent radius to mass(R;/m) ratios under coupled vibrations is investigated for various homogeneous and layered systems.The frequency-dependent stiffness and damping of foundation resting on homogeneous soils and rocks are determined using the half-space theory.The dynamic response characteristics of foundation resting on the layered system considering rock-rock combination are evaluated using finite element program with transmitting boundaries.Frequencies versus amplitude responses of block foundation are obtained for both translational and rotational motion.A new methodology is proposed for determination of dynamic response of block foundations resting on soil-rock and weathered rock-rock system in the form of equations and graphs.The variations of dimensionless natural frequency and dimensionless resonant amplitude with shear wave velocity ratio are investigated for different thicknesses of top soil/weathered rock layer.The dynamic behaviors of block foundations are also analyzed for different rock-rock systems by considering sandstone,shale and limestone underlain by basalt.The variations of stiffness,damping and amplitudes of block foundations with frequency are shown in this study for various rock—rock combinations.In the analysis,two resonant peaks are observed at two different frequencies for both translational and rotational motion.It is observed that the dimensionless resonant amplitudes decrease and natural frequencies increase with increase in shear wave velocity ratio.Finally,the parametric study is performed for block foundations with dimensions of 4 m × 3 m × 2 m and 8m×5m×2m by using generalized graphs.The variations of natural frequency and peak displacement amplitude are also studied for different top layer thicknesses and eccentric moments.展开更多
As the first link element for the transmission of shaft vibration to the pedestal and even to the hull,water-lubricated bearing plays a key role in suppressing vibration.Although the porous structure is considered as ...As the first link element for the transmission of shaft vibration to the pedestal and even to the hull,water-lubricated bearing plays a key role in suppressing vibration.Although the porous structure is considered as one of the main methods for improving the wideband vibration and noise reduction performance of materials in many industrial fields,the studies in the field of water-lubricated bearing remain insufficient.To enhance vibration reduction performance,a fluid-saturated perforated slab is designed in this study,and via the establishment of a fluid-solid coupled vibration model,the influence law and impact levels were analyzed and verified by simulation and experiments.The results obtained verified that the total vibration amplitude of damping-enhanced stern bearing in the vertical direction was smaller than that of the normal stern bearing,and the reduction amplitude of the characteristic frequency agreed with the optimal value at approximately 0.1 of the volume fraction of the liquid phase when the solid-fluid phase was rubber–water.Additionally,the increase in fluid fraction did not enhance the damping effect,instead,it unexpectedly reduced the natural frequency of the raw material significantly.This research indicates that the design of the fluid-saturated perforated slab is effective in reducing the transmission of the vibration amplitude from the shaft,and presents the best volume fraction of the liquid phase.展开更多
On the basis of Hamilton principle. the equation of sonlid-liquid coupling vibration of pipe conveying fluid is deduced. An asymmetrical sonlid-liquid coupling damp matrix and a symmetrical solid-liquid coupling Sti...On the basis of Hamilton principle. the equation of sonlid-liquid coupling vibration of pipe conveying fluid is deduced. An asymmetrical sonlid-liquid coupling damp matrix and a symmetrical solid-liquid coupling Stiffness matrix are obtained. Using QR method , pipe’s nature frequencies are calculated. The curves of the first four orders of natural frequency-flow velocity of pipe waw given .The influence of flowing velocity ,pressure, solid-liquid coupling damp and solid-liquid coupling stiffness on natural frequency are discussed respectively.The dynamic respondence of the pipes for stepload with different flow velocity are calculated by Newmark method .It is found that,with the flow velocity increased, the nature frequency of the pipes reduced, increased,reduced again and so on.展开更多
The free vibration of a functionally graded material hollow spheresubmerged in a compress- ible fluid medium is exactly analyzed. Thesphere is assumed to be spherically isotropic with material consta-nts being inhomog...The free vibration of a functionally graded material hollow spheresubmerged in a compress- ible fluid medium is exactly analyzed. Thesphere is assumed to be spherically isotropic with material consta-nts being inhomogeneous along the radial direction. By employing aseparation technique as well as the spherical harmonics expansionmethod, the governing equations are simplified to an uncoupledsecond-order ordinary differential equation, and a coupled system oftwo such equations. Solutions to these equations are given when theelastic constants and the mass density are power functions of theradial coordinate. Numerical examples are finally given to show theeffect of the material gradient on the natural frequencies.展开更多
The nonlinear modal coupling in a T-shaped piezoelectric resonator,when the former two natural frequencies are away from 1:2,is studied.Experimentally sweeping up the exciting frequency shows that the horizontal beam ...The nonlinear modal coupling in a T-shaped piezoelectric resonator,when the former two natural frequencies are away from 1:2,is studied.Experimentally sweeping up the exciting frequency shows that the horizontal beam exhibits a nonlinear hardening behavior.The first primary resonance of the vertical beam,owing to modal coupling,exhibits an abrupt amplitude increase,namely the Hopf bifurcation.The frequency comb phenomenon induced by modal coupling is measured experimentally.A Duffing-Mathieu coupled model is theoretically introduced to derive the conditions of the modal coupling and frequency comb phenomenon.The results demonstrate that the modal coupling results from nonlinear stiffness hardening and is strictly dependent on the loading range and sweeping form of the driving voltage and the frequency of the piezoelectric patches.展开更多
A nonlinear model of a low pressure cylinder-generator rotor system is presented to study sub-synchronous resonance and combined resonance. Analytical results are obtained by an averaging method. Transition sets and b...A nonlinear model of a low pressure cylinder-generator rotor system is presented to study sub-synchronous resonance and combined resonance. Analytical results are obtained by an averaging method. Transition sets and bifurcation diagrams are obtained based on the singularity theory for the two-state variable system. The bifurcation characteristics are analyzed to provide a basis for the optimal design and fault diagnosis of the rotor system. Finally, the theoretical results are verified with the numerical results.展开更多
This paper points out that Housner's equation of bending vibration of a pipe line containing flowing fluid is approximate and makes correction to it. An exact form of the vibration equation is given.
Experimental vibrational spectra of heavy light XH stretching vibrations of simple molecules have been analyzed using the local mode model.In addition,the bond dipole approach,which assumes that the transition dipole ...Experimental vibrational spectra of heavy light XH stretching vibrations of simple molecules have been analyzed using the local mode model.In addition,the bond dipole approach,which assumes that the transition dipole moment(TDM)of the XH stretching mode is aligned along the XH bond,has helped analyze experimental spectra.We performed theoretical calculations of the XH stretching vibrations of HOD,HND^−,HCD,HSD,HPD^−,and HSiD using local mode model and multi-dimensional normal modes.We found that consistent with previous notions,a localized 1D picture to treat the XH stretching vibration is valid even for analyzing the TDM tilt angle.In addition,while the TDM of the OH stretching fundamental transition tilted away from the OH bond in the direction away from the OD bond,that for the XH stretching fundamental of HSD,HND^−,HPD^−,HCD,and HSiD tilted away from the OH bond but toward the OD bond.This shows that bond dipole approximation may not be a good approximation for the present systems and that the heavy atom X can affect the transition dipole moment direction.The variation of the dipole moment was analyzed using the atoms-in-molecule method.展开更多
基金supported by the Henan Provincial Science and Technology Research Project under Grant(152102310295).
文摘A novel approach for analyzing coupled vibrations between vehicles and bridges is presented,taking into account spatiotemporal effects and mechanical phenomena resulting fromvehicle braking.Efficient modeling and solution of bridge vibrations induced by vehicle deceleration are realized using this method.The method’s validity and reliability are substantiated through numerical examples.A simply supported beam bridge with a corrugated steel web is taken as an example and the effects of parameters such as the initial vehicle speed,braking acceleration,braking location,and road surface roughness on the mid-span displacement and impact factor of the bridge are analyzed.The results show that vehicle braking significantly amplifies mid-span displacement and impact factor responses in comparison to uniform vehicular motion across the bridge.Notably,the influence of wheelto-bridge friction forces is of particular significance and cannot be overlooked.When the vehicle initiates braking near the middle of the span,both the mid-span displacement and impact factor of the bridge exhibit substantial increases,further escalating with higher braking acceleration.Under favorable road surface conditions,the midspan displacement and the impact factor during vehicle braking may exceed the design values stipulated by codes.It is important to note that road surface roughness exerts a more pronounced effect on the impact factor of the bridge in comparison to the effects of vehicle braking.
基金financially supported by the National Natural Science Foundation of China(Nos.51921003 and 51775275)National Key Laboratory of Science and Technology on Helicopter Transmission(Nanjing University of Aeronautics and Astronautics)(No.HTL-A-20G01)Postgraduate Research&Practice Innovation Program of Jiangsu Province(No.KYCX20_0179)。
文摘Ultrasonic vibration-assisted grinding(UVAG)is an effective and promising method for machining of hard-to-cut materials.This article proposed an ultrasonic vibration plate device enabling the longitudinal full-wave and transverse half-wave(L2T1)vibration mode for UVAG.The characteristics of two-dimensional coupled vibration in different directions were analyzed on the basis of apparent elastic method and finite element method.Furthermore,a correction factor was applied to correct the frequency error caused by the apparent elastic method.Finally,the comparative experiments between the conventional creep-feed grinding and UVAG of Inconel 718 nickel-based superalloy were carried out.The results indicate that the apparent elastic method with the correction factor is accurate for the design of plate device under the L2T1 vibration mode.Compared with the conventional creep-feed grinding,the UVAG causes the reduction of grinding force and the improvement of machined surface quality of Inconel 718 nickel-based superalloy.Furthermore,under the current experimental conditions,the optimal ultrasonic vibration amplitude is determined as 6μm,with which the minimum surface roughness is achieved.
基金Outstanding Youth Science Fund Subsidization of Sichuan Province, China (No. 05204033).
文摘The vibration of a Francis turbine is analyzed with the additional quality matrix method based on fluid-structure coupling (FSC). Firstly, the vibration frequency and mode of blade and runner in air and water are calculated. Secondly, the influences to runner frequency domain by large flow, small flow and design flow working conditions are compared. Finally the influences to runner modes by centrifugal forces under three rotating speeds of 400 r/rain, 500 r/min and 600 r/rain are compared. The centrifugal force and small flow working condition have greatly influence on the vibration of small runner. With the increase of centrifugal force, the vibration frequency of the runner is sharply increased. Some order frequencies are even close to the runner natural frequency in the air. Because the low frequency vibration will severely damage the stability of the turbine, low frequency vibration of units should be avoided as soon as possible.
文摘By applying the sinusoidal wave mode to simulate the rugged surface of bridge deck,accounting for vehicle-bridge interaction and using Euler-Bernoulli beam theory, a coupling vibration model of vehicle-bridge system was developed. The model was solved by mode analyzing method and Runge-Kutta method, and the dynamic response and the resonance curve of the bridge were obtained. It is found that there are two resonance regions, one represents the main resonance while the other the minor resonance, in the resonance curve. The influence due to the rugged surface, the vibration mode of bridge, and the interaction between vehicle and bridge on vibration of the system were discussed. Numerical results show that the influence due to these parameters is so significant that the effect of roughness of the bridge deck and the mode shape of the bridge can't be ignored and the vehicle velocity should be kept away from the critical speed of the vehicle.
文摘The governing equation and energy equations for thermal-elastic coupling vibration of cylindrical shell were developed. The Garlerkin method was used in numerical process. Some useful result can be concluded from numerical result. With the increase of the amplitude of temperature and coupling coefficient, the speed of vibration decaying becomes slower and the coupling effect becomes weaker. The larger the ration of length to radius and length to thickness, the faster the decaying of the vibration amplitude and the vibration frequency increase. It means the coupling effect gets stronger. The larger the coupling coefficient, the smaller the axial stress, the axial force and the bendind moment are.
基金This work was financially supported by the National Natural Science Foundation of China(Nos.51978589 and 51778544).
文摘In recent years,high-speed railways in China have developed very rapidly,and the number and span of the railway bridges are keeping increasing.Meanwhile,frequent extreme disasters,such as strong winds,earthquakes and floods,pose a significant threat to the safety of the train–bridge systems.Therefore,it is of paramount importance to evaluate the safety and comfort of trains when crossing a bridge under external excitations.In these aspects,there is abundant research but lacks a literature review.Therefore,this paper provides a comprehensive state-of-the-art review of research works on train–bridge systems under external excitations,which includes crosswinds,waves,collision loads and seismic loads.The characteristics of external excitations,the models of the train–bridge systems under external excitations,and the representative research results are summarized and analyzed.Finally,some suggestions for further research of the coupling vibration of train–bridge system under external excitations are presented.
基金supported by the National Natural Science Fundation of China(51105063)the Fundamental Research Funds for the Central Universities(N120403004)
文摘Considering the axial and radial loads, a math- ematical model of angular contact ball bearing is deduced with Hertz contact theory. With the coupling effects of lateral, torsional and axial vibrations taken into account, a lumped-parameter nonlinear dynamic model of helical gearrotor-bearing system (HGRBS) is established to obtain the transmission system dynamic response to the changes of dif- ferent parameters. The vibration differential equations of the drive system are derived through the Lagrange equation, which considers the kinetic and potential energies, the dis- sipative function and the internal/external excitation. Based on the Runge-Kutta numerical method, the dynamics of the HGRBS is investigated, which describes vibration properties of HGRBS more comprehensively. The results show that the vibration amplitudes have obvious fluctuation, and the frequency multiplication and random frequency components become increasingly obvious with changing rotational speed and eccentricity at gear and bearing positions. Axial vibration of the HGRBS also has some fluctuations. The bearing has self-variable stiffness frequency, which should be avoided in engineering design. In addition, the bearing clearance needs little attention due to its slightly discernible effect on vibration response. It is suggested that a careful examination should be made in modelling the nonlinear dynamic behavior of a helical gear-rotor-bearing system.
基金supported by the National Natural Science Foundation of China(Nos.12072204,11972238)the Natural Science Foundation of Hebei Province of China(No.A2020210039)。
文摘The influence of pavement vibration on tire adhesion is of great significance to the structure design of vehicle and pavement.The adhesion between tire and road is the key to studying vehicle dynamics,and the precise description of tire adhesion affects the accuracy of dynamic vehicle responses.However,in most models,only road roughness is considered,and the pavement vibration caused by vehicle-road interaction is ignored.In this paper,a vehicle is simplified as a spring-mass-damper oscillator,and the vehicle-pavement system is modeled as a vehicle moving along an Euler-Bernoulli beam with finite length on a nonlinear foundation.The road roughness is considered as a sine wave,and the shear stress is ignored on the pavement.According to the contact form between tire and road,the LuGre tire model is established to calculate the tire adhesion force.The Galerkin method is used to simplify the partial differential equations of beam vibration into finite ordinary differential equations.A product-to-sum formula and a Dirac delt function are used to deal with the nonlinear term caused by the nonlinear foundation,which realizes the fast and accurate calculation of super-high dimensional nonlinear ordinary differential equations.In addition,the dynamic responses between the coupled system and the traditional uncoupled system are compared with each other.The obtained results provide an important theoretical basis for research on the influence of vehicle-road coupled vibration on tire adhesion.
基金National Hi-tech Research and Development Program of China(863 Program,No.2008AA04Z116)and Natural Science Foundation of Hunan Province,China.
文摘On the basis of the traditional mechanical model of a grinding wheel rotor and the mechanical-electric coupling model with ideal sinusoidal supply, taking high-frequency converting current of inverter power switches into further consideration, a modified mechanical-electric coupling model is created. The created model consists of an inverter, a motorized spindle, a grinding wheel and grinding loads. Some typical non-stationary processes of the grinding system with two different supplies, including the starting, the speed rising and the break in grinding loads, are compared by making use of the created model. One supply is an ideal sinusoidal voltage source, the other is an inverter. The theoretical analysis of the high-order harmonic is also compared with the experimental result. The material strategy of suppressing high-order harmonic mechanical-electric coupling vibration by optimizing inverter operating parameters is proposed.
基金Project supported by the National Natural Science Foundation of China(Nos.10672092 and 10725209)Scientific Research Project of Shanghai Municipal Education Commission(No.07ZZ07)Shanghai Leading Academic Discipline Project(No.Y0103)
文摘The modal method is applied to analyze coupled vibration of belt drive systems. A belt drive system is a hybrid system consisting of continuous belts modeled as strings as well as discrete pulleys and a tensioner arm. The characteristic equation of the system is derived from the governing equation. Numerical results demenstrate the effects of the transport speed and the initial tension on natural frequencies.
基金This project is supported by National Natural Science Foundation of China (No.50375049).
文摘Zero mode natural frequency (ZMNF) is found during experiments. The ZMNF andvibrations resulted by it are studied. First, calculating method of the ZMNF excited byelectromagnetic in vibrational system of coupled mechanics and electrics are given from the view ofmagnetic energy. Laws that the ZMNF varies with active power and exciting current are obtained andare verified by experiments. Then, coupled lateral and torsional vibration of rotor shaft system isstudied by considering rest eccentricity, rotating eccentricity and swing eccentricity. UsingLargrange-Maxwell equation when three phases are asymmetric derives differential equation of thecoupled vibration. With energy method of nonlinear vibration, amplitude-frequency characteristics ofresonance are studied when rotating speed of rotor equals to ZMNF. The results show that ZMNF willoccur in turbine generators by the action of electromagnetic. Because ZMNF varies withelectromagnetic parameters, resonance can occur when exciting frequency of the rotor speed is fixedwhereas exciting current change. And also find that a generator is in the state of large amplitudein rated exciting current.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.11674206,11874253,and12174240)the Fundamental Research Funds for the Central Universities,China(Grant No.020CBLY003)。
文摘Based on the theory of composite materials and phononic crystals(PCs),a large-size rectangular piezoelectric composite plate with the quasi-periodic PC structure composed of PZT-4 and epoxy is proposed in this paper.This PC structure can suppress the transverse vibration of the piezoelectric composite plate so that the thickness mode is purer and the thickness vibration amplitude is more uniform.Firstly,the vibration of the model is analyzed theoretically,the electromechanical equivalent circuit diagram of three-dimensional coupled vibration is established,and the resonance frequency equation is derived.The effects of the length,width,and thickness of the piezoelectric composite plate at the resonant frequency are obtained by the analytical method and the finite element method,the effective electromechanical coupling coefficient is also analyzed.The results show that the resonant frequency can be changed regularly and the electromechanical conversion can be improved by adjusting the size of the rectangular piezoelectric plate.The effect of the volume fraction of the scatterer on the resonant frequency in the thickness direction is studied by the finite element method.The band gap in X and Y directions of large-size rectangular piezoelectric plate with quasi-periodic PC structures are calculated.The results show that the theoretical results are in good agreement with the simulation results.When the resonance frequency is in the band gap,the decoupling phenomenon occurs,and then the vibration mode in the thickness direction is purer.
文摘In the present study,the dynamic response of block foundations of different equivalent radius to mass(R;/m) ratios under coupled vibrations is investigated for various homogeneous and layered systems.The frequency-dependent stiffness and damping of foundation resting on homogeneous soils and rocks are determined using the half-space theory.The dynamic response characteristics of foundation resting on the layered system considering rock-rock combination are evaluated using finite element program with transmitting boundaries.Frequencies versus amplitude responses of block foundation are obtained for both translational and rotational motion.A new methodology is proposed for determination of dynamic response of block foundations resting on soil-rock and weathered rock-rock system in the form of equations and graphs.The variations of dimensionless natural frequency and dimensionless resonant amplitude with shear wave velocity ratio are investigated for different thicknesses of top soil/weathered rock layer.The dynamic behaviors of block foundations are also analyzed for different rock-rock systems by considering sandstone,shale and limestone underlain by basalt.The variations of stiffness,damping and amplitudes of block foundations with frequency are shown in this study for various rock—rock combinations.In the analysis,two resonant peaks are observed at two different frequencies for both translational and rotational motion.It is observed that the dimensionless resonant amplitudes decrease and natural frequencies increase with increase in shear wave velocity ratio.Finally,the parametric study is performed for block foundations with dimensions of 4 m × 3 m × 2 m and 8m×5m×2m by using generalized graphs.The variations of natural frequency and peak displacement amplitude are also studied for different top layer thicknesses and eccentric moments.
基金Supported by State Key Program Grant of National Natural Science Foundation of China(Grant No.51579198)Key Laboratory of High Performance Ship Technology Opening Foundation(Grant No.2016gxnc04).
文摘As the first link element for the transmission of shaft vibration to the pedestal and even to the hull,water-lubricated bearing plays a key role in suppressing vibration.Although the porous structure is considered as one of the main methods for improving the wideband vibration and noise reduction performance of materials in many industrial fields,the studies in the field of water-lubricated bearing remain insufficient.To enhance vibration reduction performance,a fluid-saturated perforated slab is designed in this study,and via the establishment of a fluid-solid coupled vibration model,the influence law and impact levels were analyzed and verified by simulation and experiments.The results obtained verified that the total vibration amplitude of damping-enhanced stern bearing in the vertical direction was smaller than that of the normal stern bearing,and the reduction amplitude of the characteristic frequency agreed with the optimal value at approximately 0.1 of the volume fraction of the liquid phase when the solid-fluid phase was rubber–water.Additionally,the increase in fluid fraction did not enhance the damping effect,instead,it unexpectedly reduced the natural frequency of the raw material significantly.This research indicates that the design of the fluid-saturated perforated slab is effective in reducing the transmission of the vibration amplitude from the shaft,and presents the best volume fraction of the liquid phase.
文摘On the basis of Hamilton principle. the equation of sonlid-liquid coupling vibration of pipe conveying fluid is deduced. An asymmetrical sonlid-liquid coupling damp matrix and a symmetrical solid-liquid coupling Stiffness matrix are obtained. Using QR method , pipe’s nature frequencies are calculated. The curves of the first four orders of natural frequency-flow velocity of pipe waw given .The influence of flowing velocity ,pressure, solid-liquid coupling damp and solid-liquid coupling stiffness on natural frequency are discussed respectively.The dynamic respondence of the pipes for stepload with different flow velocity are calculated by Newmark method .It is found that,with the flow velocity increased, the nature frequency of the pipes reduced, increased,reduced again and so on.
基金the National Natural Sciences Foundation of China(No.19872060)
文摘The free vibration of a functionally graded material hollow spheresubmerged in a compress- ible fluid medium is exactly analyzed. Thesphere is assumed to be spherically isotropic with material consta-nts being inhomogeneous along the radial direction. By employing aseparation technique as well as the spherical harmonics expansionmethod, the governing equations are simplified to an uncoupledsecond-order ordinary differential equation, and a coupled system oftwo such equations. Solutions to these equations are given when theelastic constants and the mass density are power functions of theradial coordinate. Numerical examples are finally given to show theeffect of the material gradient on the natural frequencies.
基金supported by the National Natural Science Foundation of China(No.11902182)the Program of Shanghai Academic/Technology Research Leader of China(No.19XD1421600)+2 种基金the China Postdoctoral Science Foundation(No.2019M651485)the Natural Science Foundation of Shandong Province of China(No.ZR2019BA001)the Natural Science Foundation of Tianjin of China(No.20JCQNJC01070)。
文摘The nonlinear modal coupling in a T-shaped piezoelectric resonator,when the former two natural frequencies are away from 1:2,is studied.Experimentally sweeping up the exciting frequency shows that the horizontal beam exhibits a nonlinear hardening behavior.The first primary resonance of the vertical beam,owing to modal coupling,exhibits an abrupt amplitude increase,namely the Hopf bifurcation.The frequency comb phenomenon induced by modal coupling is measured experimentally.A Duffing-Mathieu coupled model is theoretically introduced to derive the conditions of the modal coupling and frequency comb phenomenon.The results demonstrate that the modal coupling results from nonlinear stiffness hardening and is strictly dependent on the loading range and sweeping form of the driving voltage and the frequency of the piezoelectric patches.
基金Project supported by the National Natural Science Foundation of China(No.10632040)
文摘A nonlinear model of a low pressure cylinder-generator rotor system is presented to study sub-synchronous resonance and combined resonance. Analytical results are obtained by an averaging method. Transition sets and bifurcation diagrams are obtained based on the singularity theory for the two-state variable system. The bifurcation characteristics are analyzed to provide a basis for the optimal design and fault diagnosis of the rotor system. Finally, the theoretical results are verified with the numerical results.
文摘This paper points out that Housner's equation of bending vibration of a pipe line containing flowing fluid is approximate and makes correction to it. An exact form of the vibration equation is given.
文摘Experimental vibrational spectra of heavy light XH stretching vibrations of simple molecules have been analyzed using the local mode model.In addition,the bond dipole approach,which assumes that the transition dipole moment(TDM)of the XH stretching mode is aligned along the XH bond,has helped analyze experimental spectra.We performed theoretical calculations of the XH stretching vibrations of HOD,HND^−,HCD,HSD,HPD^−,and HSiD using local mode model and multi-dimensional normal modes.We found that consistent with previous notions,a localized 1D picture to treat the XH stretching vibration is valid even for analyzing the TDM tilt angle.In addition,while the TDM of the OH stretching fundamental transition tilted away from the OH bond in the direction away from the OD bond,that for the XH stretching fundamental of HSD,HND^−,HPD^−,HCD,and HSiD tilted away from the OH bond but toward the OD bond.This shows that bond dipole approximation may not be a good approximation for the present systems and that the heavy atom X can affect the transition dipole moment direction.The variation of the dipole moment was analyzed using the atoms-in-molecule method.