A photogrammetric approach for quantifying the evolution of rock joint void geometry under varying contact states

Accurate measurement of the evolution of rock joint void geometry is essential for comprehending the distribution characteristics of asperities responsible for shear and seepage behaviors.However,existing techniques often require specialized equipment and skilled operators,posing practical challenges.In this study,a cost-effective photogrammetric approach is proposed.Particularly,local coordinate systems are established to facilitate the alignment and precise quantification of the relative position between two halves of a rock joint.Push/pull tests are conducted on rock joints with varying roughness levels to induce different contact states.A high-precision laser scanner serves as a benchmark for evaluating the photogrammetry method.Despite certain deviations exist,the measured evolution of void geometry is generally consistent with the qualitative findings of previous studies.The photogrammetric measurements yield comparable accuracy to laser scanning,with maximum errors of 13.2%for aperture and 14.4%for void volume.Most joint matching coefficient(JMC)measurement errors are below 20%.Larger measurement errors occur primarily in highly mismatched rock joints with JMC values below 0.2,but even in cases where measurement errors exceed 80%,the maximum JMC error is only 0.0434.Thus,the proposed photogrammetric approach holds promise for widespread application in void geometry measurements in rock joints.

Study on the packed volume and the void ratio of idealized human red blood cells using a ?nite-discrete element method

Numerical simulations are performed to examine the packing behavior of human red blood cells(RBCs). A combined ?nite-discrete element method(FDEM) is utilized, in which the RBCs are modeled as no-friction and no-adhesion solid bodies. The packed volume and the void ratio of a large number of randomly packed RBCs are clari?ed,and the effects of the RBC shape, the mesh size, the cell number, and the container size are investigated. The results show that the packed human RBCs with normal shape have a void ratio of 28.45%, which is slightly higher than that of the ?at or thick cells used in this study. Such information is bene?cial to the further understanding on the geometric features of human RBCs and the research on RBC simulations.

Relationship between Voided Urine Volume and Urinary ATP in Healthy Volunteers

Purpose: We examined the relationship between the urinary ATP level and the desire to void, voided urine volume, and urinary osmotic pressure. Materials and Methods: The subjects were 4 healthy volunteers (2 men and 2 women) without micturition disorders who were not taking any medications and had normal urinalysis findings. Over 2 - 3 days, they urinated into a clean cup a total of 20 times. The strength of the desire to void was classified (none, slight, moderate, or strong;scored from 1 to 4, respectively) and a voiding score was assigned at each urination, along with measurement of the voided volume, urinary ATP, urinary creatinine, and urinary osmotic pressure (one man). Results: Variation of the urinary ATP/creatinine ratio was large in both male and female subjects. The urinary ATP/creatinine ratio was lower in the 2 men compared with the 2 women. This ratio showed a significant negative correlation (R2 = 0.1577 and 0.1673, both p < 0.05) with the voided urine volume in the male subjects. However, there was no relationship between the urinary ATP/creatinine ratio and the voiding score or voided urine volume in the female subjects. Conclusions: The urinary ATP level may not be a clinically useful marker of bladder pathology. Both the present study and our previous studies identified a large sex difference in the urinary ATP/creatinine ratio, and this finding may be important when considering the causes of overactive bladder (OAB) in women. The mechanism underlying the increase in urinary ATP in women should be investigated to develop new therapies for OAB.

Molecular Dynamics Simulation of Shock Response of CL-20 Co-crystals Containing Void Defects

To investigate the effect of void defects on the shock response of hexanitrohexaazaisowurtzitane(CL-20)co-crystals,shock responses of CL-20 co-crystals with energetic materials ligands trinitrotoluene(TNT),1,3-dinitrobenzene(DNB),solvents ligands dimethyl carbonate(DMC) and gamma-butyrolactone(GBL)with void were simulated,using molecular dynamics method and reactive force field.It is found that the CL-20 co-crystals with void defects will form hot spots when impacted,significantly affecting the decomposition of molecules around the void.The degree of molecular fragmentation is relatively low under the reflection velocity of 2 km/s,and the main reactions are the formation of dimer and the shedding of nitro groups.The existence of voids reduces the safety of CL-20 co-crystals,which induced the sensitivity of energetic co-crystals CL-20/TNT and CL-20/DNB to increase more significantly.Detonation has occurred under the reflection velocity of 4 km/s,energetic co-crystals are easier to polymerize than solvent co-crystals,and are not obviously affected by voids.The results show that the energy of the wave decreases after sweeping over the void,which reduces the chemical reaction frequency downstream of the void and affects the detonation performance,especially the solvent co-crystals.

A Novel Method for Determining the Void Fraction in Gas-Liquid Multi-Phase Systems Using a Dynamic Conductivity Probe

Conventional conductivity methods for measuring the void fraction in gas-liquid multiphase systems are typically affected by accuracy problems due to the presence of fluid flow and salinity.This study presents a novel approach for determining the void fraction based on a reciprocating dynamic conductivity probe used to measure the liquid film thickness under forced annular-flow conditions.The measurement system comprises a cyclone,a conductivity probe,a probe reciprocating device,and a data acquisition and processing system.This method ensures that the flow pattern is adjusted to a forced annular flow,thereby minimizing the influence of complex and variable gas-liquid flow patterns on the measurement results;Moreover,it determines the liquid film thickness solely according to circuit connectivity rather than specific conductivity values,thereby mitigating the impact of salinity.The reliability of the measurement system is demonstrated through laboratory experiments.The experimental results indicate that,in a range of gas phase superficial velocities 5–20 m/s and liquid phase superficial velocities 0.079–0.48 m/s,the maximum measurement deviation for the void fraction is 4.23%.

Mechanism of cross-level settlements and void accumulation of wide and conventional sleepers in railway ballast

The cross-level and twist irregularities are the most dangerous irregularity types that could cause wheel unloading with the risk of derailments and additional maintenance expenses.However,the mechanism of the irregularities initiation and development is unclear.The motivation of the present study was the previous experimental studies on the application of wide sleepers in the ballasted track.The long-term track geometry measurements with wide sleepers show an enormous reduction of the vertical longitudinal irregularities compared to the conventional track.However,wide sleepers had higher twist and cross-section level irregularities.The present paper aims to explain the phenomenon by discrete element method(DEM)modeling the development process of sleeper inhomogeneous support at cross-level depending on the sleeper form.The DEM simulations show that the maximal settlement intensity is up to 3.5 times lower for a wide sleeper in comparison with the conventional one.Nevertheless,the cross-level differential settlements are almost the same for both sleepers.The particle loading distribution after all loading cycles is concentrated on the smaller area,up to the half sleeper length,with fully unloaded zones under sleeper ends.Ballast flow limitation under the central part of the sleeper could improve the resilience of wide sleepers to the development of cross-level irregularities.The mechanism of initiation of the cross-level irregularity is proposed,which assumes the loss of sleeper support under sleeper ends.The further growth of inhomogeneous settlements along the sleeper is assumed as a result of the interaction of two processes:ballast flow due to dynamic impact during void closing and on the other side high pressure due to the concentration of the pressure under the middle part of the sleeper.The DEM simulation results support the assumption of the mechanism and agree with the experimental studies.

Void defect detection in BGA solder joints using mathematical morphology

Voids are one of the major defects in ball grid array （BGA） solder joints due to a large amount of outgassing flux that gets entrapped during reflow. X-ray nondestructive machines are used to make voids visible as lighter areas inside the solder joints in X-ray images for detection However, it has always been difficult to analyze this problem automatically because of some challenges such as noise, inconsistent lighting and void-like artifacts. This study realized accurate extraction and automatic a-nalysis of void defects in solder joints by adopting a technical proposal, in which Otsu algorithm was used to segment solder balls and void defects were extracted through opening and closing operations and top-hat transformation in mathematical mor-phology. Experimental results show that the technical proposal mentioned here has good robustness and can be applied in the detection of voids in BGA solder joints.

A Model on the Void Fraction in Liquid Slugs for Vertical Slug Flow

Aim To develop a hydrodynamic model on the void fraction in liquid slugs for gas liquid slug flow in vertical tubes. Methods Developing the model by considering the gas exchange between the Taylor bubble and the following liquid slug. Results Some experimental data are obtained to check the model. In comparison with previous published results, the predictions from this model are better and in good agreement with the experimental data. The error is within ±20%. Conclusion The proposed model can correctly predict the void fraction in liquid slugs for gas liquid two phase slug flow in vertical tubes.

Constitutive description for casting magnesium alloy involving void evolution

In order to investigate the effect of microvoids on the mechanical behavior of casting magnesium alloy,a spherical void-cell model of the material was presented.The velocity and strain fields of the model were obtained from the assumption that the material matrix is homogeneous and incompressible.The hardening and softening functions,which respectively reflect the deformation-hardening and void-softening behaviors of the material,were presented and introduced to an endochronic constitutive equation for describing the mechanical behavior of the material including microvoids.The corresponding numerical algorithm and finite element procedure were developed and applied to the analyses of the elastoplastic response and the porosity of casting magnesium alloy ZL102.The computed results show satisfactory agreement with experimental data.

浅谈C/C++中的void

对C语言中void关键字的含义进行了解释,并详述了void及void指针类型的使用方法和技巧．

Effects of binder strength and aggregate size on the compressive strength and void ratio of porous concrete

To test the influence of binder strength, porous concretes with 4 binder strengths between 30.0-135.0 MPa and 5 void ratios between 15%-35% were tested. The results indicated that for the same aggregate, the rates of strength reduction due to the increases in void ratio were the same for binders with different strengths. To study the influence of aggregate size, 3 single size aggregates with nominal sizes of 5.0, 13.0 and 20.0 mm （Nos. 7, 6 and 5 according to JIS A 5001） were used to make porous concrete. The strengths of porous concrete are found to be dependent on aggregate size. The rate of strength reduction of porous concrete with small aggregate size is found to be higher than that with larger aggregate size. At the same void ratio, the strength of porous concrete with large aggregate is larger than that with small aggregate. The general equations for porous concrete are related to compressive strength and void ratio for different binder strengths and aggregate sizes.

A theoretical analysis of the electromigration-induced void morphological evolution under high current density

In this work, analysis of electromigration-induced void morphological evolution in solder interconnects is performed based on mass diffusion theory. The analysis is conducted for three typical experimentally observed void shapes: circular, ellipse, and cardioid. Void morphological evolution is governed by the competition between the electric field and surface capillary force. In the developed model, both the electric field and capillary force on the void's surface are solved analytically. Based on the mass conversation principle, the normal velocity on the void surface during diffusion is obtained. The void morphological evolution behavior is investigated, and a physical model is developed to predict void collapse to a crack or to split into sub-voids under electric current. It is noted that when the electric current is being applied from the horizontal direction, a circular void may either move stably along the electric current direction or collapse to a finger shape, depending on the relative magnitude of the electric current and surface capillary force. However, the elliptical-shaped void will elongate along the electric current direction and finally collapse to the finger shape. On the other hand, the cardioid-shaped void could bifurcate into two sub-voids when the electric current reaches a critical value. The theoretical predictions agree well with the experimental observations.

Effect of the Entrained Air Void on Strength and Interfacial Transition Zone of Air-Entrained Mortar

In order to facilitate the development and application of air entraining agents (AEA) in the high performance concrete, entrained air void structure parameters (air void size range from 10 to 1 600 mu m) of 28 d sifted mortar were measured by image analysis method. The relationship between the air void size distribution and strength of mortar was studied by methods of grey connection analysis and multiple linear regression analysis. The multiple linear regression equation was established with a correlation coefficient of 0.966. The weight of the affection of hierarchical porosity on the compressive strength ratio was also obtained. In addition, the effect of air voids on the paste-aggregate interfacial transition zone (ITZ) was analyzed by microhardness. The results show that the correlation between different pore size range and the compressive strength is negative. The effect of air void size distribution on 28 days compressive strength is different: under the condition of similar total porosity, with the increase of the porosity of the air void size, ranging from 10 to 200 mu m, and the decrease of the porosity, ranging from 200 to 1 600 mu m, the average air void diameter and mean free spacing are decreased; as well as the width of ITZ. On the contrary, the microhardness of the ITZ is increased while the compressive strength loss is decreased.

Void Fraction Distributions in Cold-gassed and Hot-sparged Three Phase Stirred Tanks with Multi-impeller

Vertical distributions of void fraction in gas-liquid and gas-liquid-solid stirred tanks have been measured in a fully baffled dished base vessel of 0.48 m diameter, using a conductivity probe. The impeller configuration （a hollow half elliptical blade dispersing turbine below two up-pumping wide blade hydrofoils, identified as HEDT＋2WHu） recommended in previous work has been used in this work. The operating temperatures were 24℃ and 81℃, identified as cold and hot respectively. The effects of superficial gas velocity, agitator speed and the corresponding power input on the local void fraction in two-phase systems are .investigated and discussed. Results show thatth-e increasing of agitator speed or gas flow rate leads to an increase in local-void fraction at the majority of measurement points in both cold and hot systems. However, the unifo,rmity of gas dispersion does not always in crease as the raising of agitator speed and power input. In either cold or hot sparged conditions, the two- and three-phase systems.have similar vertical profiles for void fraction, with maxima in similar locations; however, the void fractions are significantly lower in hot sparging than with cold. In cold operation the presence of particles leads to a lower void fraction at most points, although the local void fractions increase a little with the addition of solid particles at high temperature, in good agreement with the global gas holdup results, and the possible reasons are discussed in this paper. This work can give a better understanding of the differences between cold-gassed and hot-sparged three phase＇stirred tanks.

Void Fraction Measurement in Oil-Gas Transportation Pipeline Using an Improved Electrical Capacitance Tomography System

To measure the void fraction online in oil-gas pipeline, an improved electrical capacitance tomography (ECT) system has been designed. The capacitance sensor with new structure has twelve internal electrodes and overcomes the influence of the pipe wall. The data collection system is improved by using high performance IC (integrated circuit). Static tests of bubble flow, stratified flow and annular flow regime are carried out. Measurements are taken on bubble flow, stratified flow and slug flow. Results show that the new ECT system performs well on void fraction measurement of bubble flow and stratified flow, but the error of measurement for slug flow is more than 10%.

Investigation of oil-air two-phase mass flow rate measurement using Venturi and void fraction sensor

Oil-air two-phase flow measurement was investigated with a Venturi and void fraction meters in this work. This paper proposes a new flow rate measurement correlation in which the effect of the velocity ratio between gas and liquid was considered. With the pressure drop across the Venturi and the void fraction that was measured by electrical capacitance tomography apparatus, both mixture flow rate and oil flow rate could be obtained by the correlation. Experiments included bubble-, slug-, wave and annular flow with the void fraction ranging from 15% to 83%, the oil flow rate ranging from 0.97 kg/s to 1.78 kg/s, the gas flow rate ranging up to 0.018 kg/s and quality ranging nearly up to 2.0%. The root-mean-square errors of mixture mass flow rate and that of oil mass flow rate were less than 5%. Furthermore, coefficients of the correlation were modified based on flow regimes, with the results showing reduced root-mean-square errors.

An Investigation on the Void Fraction for upward Gas-Liquid Slug Flow in Vertical Pipe

In order to investigate the influence of the entrance effect on the spatial distribution of phases, the experiments on gas-liquid two-phase slug flow in a vertical pipe of 0.03m ID were carried out by using optical probes and an EKTAPRO 1000 high speed motion analyzer. It demonstrates that the radial profile of slug flow void fraction is parabolic. Influenced by the falling liquid film, the radial profile curve of liquid slug void fraction in the wake region is also parabolic. Since fully turbulent velocity distribution is built up in the developed region,the void fraction profile in this region is the saddle type. At given superficial liquid velocity, the liquid slug void fraction increases with gas velocity. The radial profiles of liquid slug void fraction at different axial locations are all saddle curves, but void fraction is obviously high around the centerline in the entrance region. The nearer the measuring station is from the entrance, the farther the peak location is away from the wall.

Effect of Rare Earth on Void Band of Diffusion Layer and Properties of Aluminized Steel

The effects of the addition of rare earth （RE） elements on the void band in the diffusion layer, and the re sistances to both oxidation and spalling of aluminized steel were investigated through high temperature oxidation and spalling tests. The results showed that RE had significant effects on the void band in the diffusion layer and the properties of aluminized steel. After diffusion treatment, a considerable number of the voids between the middle layer and transitional layer of pure aluminized coating, aggregated into wavy-line-shaped void bands parallel to the outer surface. For the RE added aluminized coating, only a few voids aggregated into intermittent block shapes. During high temperature oxidation at 800 ℃ for 200 h, the wavy void band of pure aluminized coating aggregated further into a linear crack parallel to the outer surface, and the internal oxidation occurred within them; the open cracks perpendicular to the surface penetrated through the diffusion layer. For the RE added aluminized coating, only a few voids aggregated into intermittent meniscus shapes. During cyclic spalling tests, the peeling, spallation, and pulver ulent cracking occurred along the void band in the diffusion layer of pure aluminized coating, but only a little spallation occurred in the diffusion layer of the RE-added aluminized coating, in which cracks perpendicular to the surface were much smaller than those of pure aluminized coating and did not penetrate through the diffusion layer. It is evident that RE addition can restrain the formation and aggregation of voids and subsequently improve the resistances to oxidation and spalling. The mechanism of the RE effect on the void band in the diffusion layer is also discussed.

The reuse of abandoned Acquaresi mine voids for storage of the Masua flotation tailings

Often in abandoned mine sites are present both underground voids produced by mining and the tailings of treatment plant.An interesting solution for the rehabilitation of the sites would be to place the tailings of the process in the underground mining voids,thus obtaining the reclamation of surface areas and the stabilization of abandoned voids to prevent the dangerous phenomena of subsidence.However,these operations require inert waste,which must not be source of pollution,and the choice of a water/solid optimum to ensure good conditions of pumpability.

Molecular dynamics simulation on plasticity deformation mechanism and failure near void for magnesium alloy

The plastic deformation processes of magnesium alloys near a void at atomic scale level were examined through molecular dynamics(MD)simulation.The modified embedded atom method(MEAM)potentials were employed to characterize the interaction between atoms of the magnesium alloy specimen with only a void.The void growth and crystal failure processes for hexagonal close-packed(hcp)structure were observed.The calculating results reveal that the deformation mechanism near a void in magnesium alloy is a complex process.The passivation around the void,dislocation emission,and coalescence of the void and micro-cavities lead to rapid void growth.