Assessment of Low Global Warming Potential Refrigerants for Waste Heat Recovery in Data Center with On-Chip Two-Phase Cooling Loop

Data centers(DCs)are highly energy-intensive facilities,where about 30%–50%of the power consumed is attributable to the cooling of information technology equipment.This makes liquid cooling,especially in twophase mode,as an alternative to air cooling for the microprocessors in servers of interest.The need to meet the increased power density of server racks in high-performance DCs,along with the push towards lower global warming potential(GWP)refrigerants due to environmental concerns,has motivated research on the selection of two-phase heat transfer fluids for cooling servers while simultaneously recovering waste heat.With this regard,a heat pump-assisted absorption chiller(HPAAC)system for recovering waste heat in DCs with an on-chip twophase cooling loop driven by the compressor is proposed in the present paper and the low GWP hydrofluoroolefin refrigerants,including R1224yd(Z),R1233zd(E),R1234yf,R1234ze(E),R1234ze(Z),R1243zf and R1336mzz(Z),are evaluated and compared against R245fa as server coolant.For theHPAAC system,beginning with the development of energy and economic models,the performance is analyzed through both a parametric study and optimization using the coefficient of performance(COP),energy saving ratio(ESR),payback period(PBP)and net present value(NPV)as thermo-economic indicators.Using a standard vapor compression cooling system as a benchmark,the results indicate that with the evaporation temperature between 50℃and 70℃and the subcooling degree ranging from5℃to 15°C,R1233zd(E)with moderate compressor suction pressure and pressure ratio is the best refrigerant for the HPAAC systemwhile R1234yf performs the worst.More importantly,R1233zd(E)is also superior to R245fa based on thermo-economic performance,especially under work conditions with relatively lower evaporation temperature as well as subcooling degree.Under the given working conditions,the overall COP,ESR,NPV,and PBP of R1233zd(E)HPAAC with optimum subcooling degree range from4.99 to 11.27,25.53 to 64.59,1.13 to 4.10×10^(7) CNY and 5.77 to 2.22 years,respectively.Besides,the thermo-economic performance of R1233zd(E)HPAAC under optimum working conditions in terms of subcooling degree varying with the evaporation temperature is also investigated.

Dynamic test on waste heat recovery system with organic Rankine cycle

Dynamic performance is important to the controlling and monitoring of the organic Rankine cycle(ORC) system so to avoid the occurrence of unwanted conditions. A small scale waste heat recovery system with organic Rankine cycle was constructed and the dynamic behavior was presented. In the dynamic test, the pump was stopped and then started. In addition, there was a step change of the flue gas volume flow rate and the converter frequency of multistage pump, respectively. The results indicate that the working fluid flow rate has the shortest response time, followed by the expander inlet pressure and the expander inlet temperature.The operation frequency of pump is a key parameter for the ORC system. Due to a step change of pump frequency(39.49-35.24 Hz),the expander efficiency and thermal efficiency drop by 16% and 21% within 2 min, respectively. Besides, the saturated mixture can lead to an increase of the expander rotation speed.

Application of the waste heat recovery system and energy-saving in the strip continuous annealing furnace

The common problem of cold strip continuous annealing furnaces is high exhaust gas temperature and great energy consumption. Taking the cold-strip continuous annealing furnaces of Baosteel No. 4 cold mill plant as an example, several waste heat recovery systems in the annealing furnaces are compared and their advantages and disadvantages are analyzed through different energy-saving technologies.

Off-Design Simulation of a CSP Power Plant Integrated with aWaste Heat Recovery System

Concentrating Solar Power(CSP)plants offer a promising way to generate low-emission energy.However,these plants face challenges such as reduced sunlight during winter and cloudy days,despite being located in high solar radiation areas.Furthermore,their dispatch capacities and yields can be affected by high electricity consumption,particularly at night.The present work aims to develop an off-design model that evaluates the hourly and annual performances of a parabolic trough power plant(PTPP)equipped with a waste heat recovery system.The study aims to compare the performances of this new layout with those of the conventional Andasol 1 plant,with the aim of assessing the improvements achieved in the new design.Based on the results,it can be concluded that the new layout has increased the annual generated power to almost 183 GWh(an increase of about 7.60% is achieved compared to the Andasol 1 layout that generates 169 GWh annually).Additionally,the proposed installation has achieved an efficiency of 20.55%,which represents a 7.87% increase compared to the previous design(19.05%).The Levelized Cost of Electricity(LCOE)of the new layout has been reduced by more than 5.8% compared to the Andasol 1 plant.Specifically,it has decreased from 13.11 to 12.35 c/kWh.This reduction in LCOE highlights the improved cost-effectiveness of the newlayout,making it amore economically viable option for generating electricity compared to the conventional Andasol 1 plant.

Gas Turbine Design and Matching Research of Waste Heat Recovery System for Marine Diesel Engine

With the emphasis on energy and environmental protection,energy-conservation and emission-reduction become vital issues for industrial development.Moreover,with the development of legislation on marine environment,the marine diesel engine has become focusing on energy saving and emission reduction for ships.For low-speed diesel engines under high load,waste heat from exhaust gas can be recovered by the compact and efficient gas turbine.In this paper,the matching design research between low speed diesel engine and gas turbine is carried out.To balance efficiency and compactness,the impeller was adjusted and generated by ANSYS BLADEGEN,based on 1D thermodynamic design.And the 1D calculation is similar to the ANSYS CFX simulation result:the total-static efficiency is 73.8%compared to 76.7%.Moreover,the flow separation happened at the impeller suction side and created vortex due to the high incidence angle.The off-design operating point simulation of the turbine shows though the pressure ratio increase will cause the efficiency to decline a little,the total shaft power rises.In sum,this paper worked out a power turbine suitable for a low-speed diesel engine according to the turbine character matching design and simulation,which provides foundation to the construction of a steady operation of waste heat recovery system for marine diesel engine.

Optimal Analysis of Pure Low-Temperature Waste Heat Recovery Generation System

In this paper, a detailed thermodynamic analysis of the pure low-temperature waste heat recovery generation system is presented. The parameters affecting the system performance are compared to obtain the most significant ones; furthermore, parameter values are optimized for the largest power generating capability of the system. It is found that the most important parameters are inlet flue gas temperature, steam pressure and the pinch point temperature difference. There is an optimal superheated steam pressure value for giving the maximum generation power per unit flue gas. With the increase of inlet flue gas temperature, the generating power increases and the optimized steam pressure rises as well. However, with increase in pinch point temperature difference, the generating power decreases and the optimized steam pressure decreases as well. The theoretical calculation provides a theoretical basis for the parameters optimization in the design of the pure low-temperature waste heat recovery eeneration swtem

Integration of Low-level Waste Heat Recovery and Liquefied Nature Gas Cold Energy Utilization

Two novel thermal cycles based on Brayton cycle and Rankine cycle are proposed, respectively, which integrate the recovery of low-level waste heat and Liquefied Nature Gas （LNG） cold energy utilization for power generation. Cascade utilization of energy is realized in the two thermal cycles, where low-level waste heat,low-temperature exergy and pressure exergy of LNG are utilized efficiently through the system synthesis. The simulations are carried out using the commercial Aspen Plus 10.2, and the results are analyzed. Compared with the conventional Brayton cycle and Rankine cycle, the two novel cycles bring 60.94% and 60% in exergy efficiency, respectively and 53.08% and 52.31% in thermal efficiency, respectively.

A review on current development of thermophotovoltaic technology in heat recovery

The burning of fossil fuels in industry results in significant carbon emissions,and the heat generated is often not fully utilized.For high-temperature industries,thermophotovoltaics(TPVs)is an effective method for waste heat recovery.This review covers two aspects of high-efficiency TPV systems and industrial waste heat applications.At the system level,representative results of TPV complete the systems,while selective emitters and photovoltaic cells in the last decade are compiled.The key points of components to improve the energy conversion efficiency are further analyzed,and the related micro/nano-fabrication methods are introduced.At the application level,the feasibility of TPV applications in high-temperature industries is shown from the world waste heat utilization situation.The potential of TPV in waste heat recovery and carbon neutrality is illustrated with the steel industry as an example.

Parametric optimization of packed bed for activated coal fly ash waste heat recovery using CFD techniques

Coal fly ash is an industrial solid waste generated from coal preparation during the processing and cleaning of coal for electric power generation.Comprehensive investigation on the reutilization of waste heat of activated coal fly ash is of great economic significance.The method of recovering the waste heat,proposed in this study,is the transfer of heat from activated coal fly ash to gas with the movement of air using the packed bed,providing valuable energy sources for preheating the raw coal fly ash to reduce the overall energy consumption.The investigation is carried on the heat transfer characteristics of gas–solid(activated coal fly ash)phases and air temperature fields of the packed bed under some key conditions via computational fluid dynamics.A two dimensional geometry is utilized to represent key parts of packed bed.The distribution mechanism of the temperature field for gas phase is analyzed based on the transient temperature contours at different times.The results show that the obtained rule of gas–solid heat transfer can effectively evaluate the influences of operating parameters on the air temperature in the packed bed.Simultaneously,it is found that no temperature differences exist in the hot air at the outlet of the packed bed.The investigation provides guidance for the design and optimization of other similar energy recovery apparatuses in industries.

Waste Heat Recovery from a Drier Receiver of an A/C Unit Using Thermoelectric Generators

Thermoelectric generators(TEGs)are considered promising devices for waste heat recovery from various systems.The Seebeck effect can be utilized to generate power using the residual heat emitted by the filter dryer receiver(FDR)of an air conditioning(A/C)system,which would otherwise go to waste.The study aims to build a set of thermoelectric generators(TEG)to collect the waste heat of the FDR and generate low-power electricity.A novel electrical circuit with two transformers is designed and fabricated to produce a more stable voltage for operation and charging.The thermoelectric generator(TEGs)was installed on the FDR of the A/C unit.The test showed that climate conditions have a significant impact on the output power generated from the system.The results showed that the peak voltage recorded in the current study is 5.2 V per day(wet,cold,and wind weather)with an output power of 0.2 W.These values are acceptable for powering the load and charging a single battery with 3.5 V as the voltage increases battery 0.1 V/20 min charge.A case study of operating the emergency signs in a building was considered.The current heat recovery system is deemed to be easily installed and can be connected to a network of TEGs to produce more power.

Simulation Analysis of Flue Gas Waste Heat Utilization Retrofit Based on ORC System

Recovery of waste heat from boiler flue gas is an effective way to improve energy utilization efficiency.Taking a heating station heating project as an example,the existing heating system of this heating station was analyzed for its underutilized flue gas waste heat and low energy utilization rate.Rankine cycle is an effective waste heat recovery method,and a steam boiler organic Rankine cycle(ORC)cogeneration waste heat utilization method is proposed.The system model simulation is constructed and verified.First,a thermodynamic model was constructed in MATLAB and five suitable work gases were selected to analyze the effects of evaporation temperature and condensation temperature on the network and thermal efficiency of the waste heat cycle power system.Secondly,the ORC model is invoked in TRNSYS to construct the improved cogeneration system,and the rationality of the remaining heat utilization methods is determined by calculating and analyzing the thermal performance,economy,and environmental protection of the improved system.The simulation results show that the system can generate about 552,000 kWh of electricity per year,and improving the energy utilization rate from 0.72 to 0.78.

DETERMINATION OF THE OPTIMAL RANKINE CYCLE FOR WASTE HEAT RECOVERY

In this paper,the optimal Rankine Cycle for waste heat recovery is considered after pro-cess integration.The exergetic efficiency is used to measure the thermodynamic performance of the re-covery system.Comparing with recovering a single waste heat stream,heat recovery after processintegration is much more complicated due to the changeable specific heat given by the process grandcomposite curves.Therefore,this paper attempts to focus attention on the influence of grand compos-ite curves on the optimization.

Heat Transfer and Energy Utilization of Waste Heat Recovery Device with Different Internal Component

Steel industry is high energy-consuming industry, and its waste?heat recovery is critically?important for energy utilization. In this study, pipeline bundle is used to enhance heat transfer in?waste?heat recovery device,?and?associated gas-solid heat transfer and energy utilization performance with different pipeline arrangement, pipe diameter and shape of internal component are further analyzed. The temperatures of gas and particle in device with pipeline bundle periodically fluctuate in horizontal direction, and those in staggered system distribute more uniformly than those in paralleled system. Compared with paralleled device, exergy and waste heat utilization efficiency of staggered device have been improved, and they are both higher than?those without pipeline. As pipe diameter increases, exergy and waste heat utilization efficiency first increases and then decreases, and they reach the maxima with optimal pipe diameter.?As the width of internal component keeps constant, influence of its shape on heat transfer is very little.

The heat recovery simulation in the system of dry granulation of the steel slag

In present,the wet-based pattern is mainly adopted to deal with the steel slag by steel plant at home and abroad,the wet-based technology has some defects;Wasting of water,pollution of the environment,and the slag has not been fully recycled.This paper presents a new method,which is aimed to realize dry granulation,waste heat recovery and comprehensive utilizing the steel slag.According to the ideas of wind quenching granulation,the heating slag from the converter furnace,was bring to the granulation heat exchange system,through the process of breaking in a container,the granulation heat exchange system has the functions of feeding continuously and heat exchange.The heat air,through the diversion tubes,could be recycled in removing the dust.The granulation slag could be bring to a confined roller,granulating and cooling secondarily.The roller export was connected to a magnetic separator.The separated iron could be recycled,and the remaining slag could also be reused as building materials,in process of stabilization and secondary magnetic separation.The heated air could be guided into the boiler to generate the steam,which can be used to generate electricity,or use as cleaned energy,realizing the target to recycle the waste heat in steel slag.The highlights of the new method are dry granulation and waste heat recovery.This paper states the process of heat exchange between the air and the steel slag in the system of granulation heat exchange in the new technical process.In theory,it has been proved reasonable with the the system of granulation heat exchange,and also the work conditions has been optimized.

Waste heat recovery from hot steel slag on the production line:Numerical simulation,validation and industrial test

Waste heat recovery from hot steel slag was determined in a granular bed through the combination of numerical simulation and an industrial test method.First,the effective thermal conductivity of the granular bed was calculated.Then,the unsteady-state model was used to simulate the heat recovery under three different flow fields(O-type,S-type,and nonshielding type(Nontype)).Second,the simulation results were validated by in-situ industrial experiments.The two methods confirmed that the heat recovery efficiencies of the flow fields from high to low followed the order of Nontype,S-type,and O-type.Finally,heat recovery was carried out under the Nontype flow field in an industrial test.The heat recovery efficiency increased from~76%and~78%to~81%when the steel slag thickness decreased from 400 and 300 to 200 mm,corresponding to reductions in the steel slag mass from 3.96 and 2.97 to 1.98 t with a blower air volume of 14687 m^(3)/h.Therefore,the research results showed that numerical simulation can not only guide experiments on waste heat recovery but also optimize the flow field.Most importantly,the method proposed in this paper has achieved higher waste heat recovery from hot steel slag in industrial scale.

Simulation of CO_2 Brayton Cycle for Engine Exhaust Heat Recovery under Various Operating Loads

A bottoming cycle system based on CO2 Brayton cycle is proposed to recover the engine exhaust heat. Its performance is compared with the conventional air Brayton cycle under five typical engine conditions. The results show that CO2 Brayton cycle proves to be superior to the air Brayton cycle in terms of the system net output power, thermal efficiency and recovery efficiency. In most cases, the recovery efficiency of CO2 Brayton cycle can be higher than 9% and the system has a better performance at the engine＇s high operating load, The thermal efficiency can be as large as 24.83% under 100% olaerating load, accordingly, the net outnut nower of 14.86 kW in nhtnined

Technical and Economic Aspects and Experience from 6 Years of Operating the Technology Using the Waste Heat from the Exhaust Gases of Heat Sources and 3 Years of Operating a Heating Plant in an Autonomous, Island Regime

This article is focused on technical and economic evaluation of more than 6-years experiences of operating the Waste Heat Recovery technology—the manner and system of flue gas processing generated in the combustion process in heat & power plants, cogeneration units, etc., which burn the gaseous fuel, primarily natural gas, or methane, biogas, geothermal gas, or other gaseous mixtures containing hydrogen. The solution proposes a more effective and non-traditional use of gaseous fuel for heating, the flue gases of which are processed in order to extract additional utilisable heat, with potential elimination of CO2 from them. Deploying of the heating plant in an island regime (OFF-GRID) enables definition of the benefits brought by the 3 years of operational experience and presents visions for the future offering the possibility to utilise the support energy services at the municipal as well as regional level.

Simulation Research on Performance of a Novel Heating and Cooling System with Thermoelectric Module

This work proposes a novel heating and cooling system,with incorporated thermoelectric module,that can achieve energy balance using a self-water supply heat exchange subsystem.The thermoelectric effect is used to achieve controlled and adjustable heating of the circulating water.Simulations were conducted to study the thermal performance of the system while it simultaneously produces hot and cold water,with different working conditions for the hot-and cold-side water outlets.The results show that the water temperature at the hot side outlet increases from 32℃to 75℃when the power increases from 4.5 to 50 W.Additionally,the use of thermoelectric modules to heat water and recover waste heat is 22%more efficient than ordinary electric water heating systems.

Transforming Waste Heat into“Renewable Heat”

Introduction:The current worldwide electric power&heat&cool production has a negative impact on the environment by emissions and enormous leaks of low-potential waste heat.Transformation of unused industrial low power heat into“renewable heat”useful to enhance the efficiency of the system is essential and actual innovation in the field of worldwide environmental protection.By introducing and defining the terminology of low-potential,“renewable”,“green heat”has created a new,parallel category of research in the energy sector.Traditional co-generation systems produce heat for space heating and hot water and generate electricity.Moving to tri-generation allows growing demand for air conditioning for homes,offices and commercial spaces such as server rooms and switchboards to be met simultaneously or on a seasonal basis.Tri-generation,or combined cooling,heat and power,is the process by which some of the heat produced by a co-generation plant is used to generate chilled water for air conditioning or refrigeration.Usually an absorption chiller is linked to the plant to provide this functionality.The technical solution is related to the new efficient manner and system of simultaneous generation of heat/cold from multiple heat sources,which has not yet been known,but in practice required.New system also enables advantageous utilization of solar power in supporting of the cooling output.The innovative system can be operated also within the existing central heating distribution systems.

Thermodynamic,Economic,and Environmental Analyses and Multi-Objective Optimization of Dual-Pressure Organic Rankine Cycle System with Dual-Stage Ejector

A novel dual-pressure organic Rankine cycle system(DPORC)with a dual-stage ejector(DE-DPORC)is proposed.The system incorporates a dual-stage ejector that utilizes a small amount of extraction steam from the highpressure expander to pressurize a large quantity of exhaust gas to performwork for the low-pressure expander.This innovative approach addresses condensing pressure limitations,reduces power consumption during pressurization,minimizes heat loss,and enhances the utilization efficiency of waste heat steam.A thermodynamic model is developed with net output work,thermal efficiency,and exergy efficiency(W_(net,ηt,ηex))as evaluation criteria,an economicmodel is established with levelized energy cost(LEC)as evaluation index,anenvironmentalmodel is created with annual equivalent carbon dioxide emission reduction(AER)as evaluation parameter.A comprehensive analysis is conducted on the impact of heat source temperature(T_(S,in)),evaporation temperature(T_(2)),entrainment ratio(E_(r1),E_(r2)),and working fluid pressure(P_(5),P_(6))on system performance.It compares the comprehensive performance of the DE-DPORC system with that of the DPORC system at TS,in of 433.15 K and T2 of 378.15 K.Furthermore,multi-objective optimization using the dragonfly algorithm is performed to determine optimal working conditions for the DE-DPORC system through the TOPSIS method.The findings indicate that the DEDPORC system exhibits a 5.34%increase inWnet andηex,a 58.06%increase inηt,a 5.61%increase in AER,and a reduction of 47.67%and 13.51%in the heat dissipation of the condenser andLEC,compared to theDPORCsystem,highlighting the advantages of this enhanced system.The optimal operating conditions are TS,in=426.74 K,T_(2)=389.37 K,E_(r1)=1.33,E_(r2)=3.17,P_(5)=0.39 MPa,P_(6)=1.32 MPa,which offer valuable technical support for engineering applications;however,they are approaching the peak thermodynamic and environmental performance while falling short of the highest economic performance.