Effects of Using Municipal Solid Waste Incineration Tailings as Lightweight Aggregate on the Mechanical Properties of Specified Density Concrete

Municipal solid waste incineration tailings were used as lightweight aggregate(MSWIT-LA)in the preparation of specified density concrete to study the effects on compressive strength,axial compressive strength,flexural strength,microhardness,total number of pores,pore area,and pore spacing.The results showed that the internal curing and morphological effects induced by an appropriate quantity of MSWIT-LA improved the compressive response of specified density concrete specimens,whereas an excessive quantity of MSWIT-LA significantly reduced their mechanical properties.An analysis of pore structure indicated that the addition of MSWIT-LA increased the total quantity of pores and promoted cement hydration,resulting in a denser microstructure than that of ordinary concrete.The results of a principal component analysis showed that the mechanical response of specified density concrete prepared with 25%MSWIT-LA was superior to that of an equivalent ordinary concrete.It was therefore concluded that MSWIT-LA can be feasibly applied to achieve excellent specified density concrete properties while utilising municipal solid waste incineration tailings to protect the environment and alleviate shortages of sand and gravel resources.

Model Prediction and Optimal Control of Gas Oxygen Content for A Municipal Solid Waste Incineration Process

In the municipal solid waste incineration process,it is difficult to effectively control the gas oxygen content by setting the air flow according to artificial experience.To address this problem,this paper proposes an optimization control method of gas oxygen content based on model predictive control.First,a stochastic configuration network is utilized to establish a prediction model of gas oxygen content.Second,an improved differential evolution algorithm that is based on parameter adaptive and t-distribution strategy is employed to address the set value of air flow.Finally,model predictive control is combined with the event triggering strategy to reduce the amount of computation and the controller's frequent actions.The experimental results show that the optimization control method proposed in this paper obtains a smaller degree of fluctuation in the air flow set value,which can ensure the tracking control performance of the gas oxygen content while reducing the amount of calculation.

Prediction of NO_(x)concentration using modular long short-term memory neural network for municipal solid waste incineration

Air pollution control poses a major problem in the implementation of municipal solid waste incineration(MSWI).Accurate prediction of nitrogen oxides(NO_(x))concentration plays an important role in efficient NO_(x)emission controlling.In this study,a modular long short-term memory(M-LSTM)network is developed to design an efficient prediction model for NO_(x)concentration.First,the fuzzy C means(FCM)algorithm is utilized to divide the task into several sub-tasks,aiming to realize the divide-and-conquer ability for complex task.Second,long short-term memory(LSTM)neural networks are applied to tackle corresponding sub-tasks,which can improve the prediction accuracy of the sub-networks.Third,a cooperative decision strategy is designed to guarantee the generalization performance during the testing or application stage.Finally,after being evaluated by a benchmark simulation,the proposed method is applied to a real MSWI process.And the experimental results demonstrate the considerable prediction ability of the M-LSTM network.

Mechanical and environmental properties of geopolymer-stabilized domestic waste incineration slag in an asphalt pavement base

Domestic waste incineration slag(WIS)includes fly ash and slag.Fly ash is classified as hazardous waste because it contains heavy metals.Most of slag are directly stacked or landfilled due to problems such as large output and low utilization rate.Harmless treatment is imminent.If WIS is used effectively in the road engineering,which can realize the high-quality and high-efficiency recycling of WIS,and it is of great significance to save resources and protect the environment.This study applies a geopolymer prepared from WIS fly ash as a stabilizing agent in WIS blending macadam for use as a pavement base mixture,and reports the mechanical properties(unconfined compressive strength,splitting strength,and resilience modulus)of the geopolymer-stabilized WIS blending macadam(GeoWIS).The leaching concentrations of harmful heavy metals of GeoWIS soaked in water were also investigated.Finally,the strength formation and heavy metal stability mechanisms were explored.The unconfined compressive strength,splitting strength,and compressive resilient modulus of GeoWIS all increased with increasing geopolymer content and decreasing WIS content.The strength of GeoWIS was derived from its geopolymerization and hydration products(C-S-H gel,N-A-S-H gel,and AFt).When the geopolymer content reached 12%–14%,the GeoWIS without natural macadam met the strength criterion of the asphalt pavement base.Through physical adsorption and chemical bonding,the geopolymer significantly reduced the leaching of harmful heavy metals.In GeoWIS with 50%WIS and stabilized with 10%geopolymer,the Cr,Ni,Cd,and Pb concentrations met the grade III groundwater standard.Concentrations of heavy metals leached from GeoWIS are low and exert little impact on environment.

Application of Multivariate Reinforcement Learning Engine in Optimizing the Power Generation Process of Domestic Waste Incineration

Garbage incineration is an ideal method for the harmless and resource-oriented treatment of urban domestic waste.However,current domestic waste incineration power plants often face challenges related to maintaining consistent steam production and high operational costs.This article capitalizes on the technical advantages of big data artificial intelligence,optimizing the power generation process of domestic waste incineration as the entry point,and adopts four main engine modules of Alibaba Cloud reinforcement learning algorithm engine,operating parameter prediction engine,anomaly recognition engine,and video visual recognition algorithm engine.The reinforcement learning algorithm extracts the operational parameters of each incinerator to obtain a control benchmark.Through the operating parameter prediction algorithm,prediction models for drum pressure,primary steam flow,NOx,SO2,and HCl are constructed to achieve short-term prediction of operational parameters,ultimately improving control performance.The anomaly recognition algorithm develops a thickness identification model for the material layer in the drying section,allowing for rapid and effective assessment of feed material thickness to ensure uniformity control.Meanwhile,the visual recognition algorithm identifies flame images and assesses the combustion status and location of the combustion fire line within the furnace.This real-time understanding of furnace flame combustion conditions guides adjustments to the grate and air volume.Integrating AI technology into the waste incineration sector empowers the environmental protection industry with the potential to leverage big data.This development holds practical significance in optimizing the harmless and resource-oriented treatment of urban domestic waste,reducing operational costs,and increasing efficiency.

Dichlorination in a circulating fluidized-bed incinerator for municipal solid waste incineration system

Cl is one of the main pollutants emitted from domestic waste incineration systems. In this study, we focused on the process of Ca dechlorination in the furnace of a circulating fluidized-bed waste incineration system. We analyzed the stability of CaCl_(2) and Ca in the furnace, the dechlorination process, and distribution of Cl in the incineration system. The results show that the optimal Ca/Cl molar ratio for Ca dechlorination in the circulating fluidized-bed waste incinerator is 2:1;moreover, the dechlorination product CaCl_(2) was found to decompose at high temperatures (> 850℃). At temperatures > 700℃, we measured CaCl_(2) decomposition rates up to 80%. Ca was added in the furnace, mainly to provide a dechlorination Ca source for the decomposition of limestone into tail flue gas. The amount of Ca^(2+) in the flue decreased gradually, parallelly to the temperature of the flue gas. Stable CaCl_(2) was formed after HCl was captured, and relatively small solid particles appeared in the ash collecting bag.

Leaching behavior of heavy metals with hydrochloric acid fromfly ash generated in municipal waste incineration plants

The extraction behavior of heavy metals from municipal waste incineration （MWI） fly ash was investigated systematically. The extraction process includes two steps, namely, fly ash was firstly washed with water, and then subjected to hydrochloric acid leaching. The main parameters for water washing process were tested, and under the optimal conditions, about 86% Na, 70% K and 12% Ca were removed from fly ash, respectively. Hydrochloric acid was used for the extraction of valuable elements from the water-washed fly ash, and the optimal extraction was achieved for each heavy metal as follows： 86% for Pb, 98% for Zn, 82% for Fe, 96% for Cd, 62% for Cu, 80% for Al, respectively. And the main compositions of the finally obtained solid residue are Ca2PbO4, CaSi2Os, PbsSiO7, Ca3A12Si3012 and SiO2.

Investigation of heavy metal partitioning influenced by flue gas moisture and chlorine content during waste incineration

The impact of moisture on the partitioning of the heavy metals including Pb,Zn,Cu and Cd in municipal solid waste （MSW） was studied in a laboratory tubular furnace.A thermodynamic investigation using CHEMKIN software was performed to compare the experimental results.Simulated waste,representative of typical MSW with and without chlorine compounds,was burned at the background temperature of 700 and 950°C,respectively.In the absence of chlorine,the moisture content has no evident effect on the volatility of Pb,Zn and Cu at either 700 or 950°C,however,as flue gas moisture increasing the Cd distribution in the bottom ash increased at 700°C and reduced at 950°C,respectively.In the presence of chlorine,the flue gas moisture reduced the volatility of Pb,Zn and Cu due to the transformation of the more volatile metal chlorides into less volatile metal oxides,and the reduction became significant as chlorine content increase.For Cd,the chlorine promotes its volatility through the formation of more volatile CdCl 2.As a result,the increased moisture content increases the Pb,Zn,Cu and Cd concentrations in the bottom ash,which limits the utilization of the bottom ash as a construction material.Therefore,in order to accumulate heavy metals into the fly ash,MSW should be dried before incineration.

Effect of quarry dust addition on the performance of controlled low-strength material made from industrial waste incineration bottom ash

The performance of industrial waste incineration bottom ash in controlled low-strength material （CLSM） was investigated in this paper, as the quarry dust was added. CLSM mixtures were made from the industrial waste incineration bottom ash, quarry dust, and cement. Tests for fresh density, bleeding, compressive strength, shear strength, hydraulic conductivity, and excavatability were carried out. The com- pressive strength ranges from 60 kPa to 6790 kPa, the friction angle varies from 5°to 19°, and the cohesion is from 4 to 604 kPa. Most of the mixtures are found to be non-excavatable. It is indicated that the quarry dust addition increases the compressive strength and shear parame- ters, decreases bleeding, and increases the removability modulus.

Microstructures and thermal properties of municipal solid waste incineration fly ash

To analyze the feasibility of utilization of thermal technology in fly ash treatment, thermal properties and microstructures of municipal solid waste incineration （MSW1） fly ash were studied by measuring the chemical element composition, specific surface area, pore sizes, functional groups, TEM image, mineralogy and DSC-TG curves of raw and sintered fly ash specimens. The results show that MSWI fly ash particles mostly have irregular shapes and non-typical pore structure, and the supersonic treatment improves the pore structure; MSWI fly ash consists of Such crystals as SiO2, CaSO4 and silica-aluminates, and some soluble salts like KCl and NaCl. During the sintering process, mineralogy changes largely and novel solid solutions are produced gradually with the rise of temperature. Therefore, the utilization of a proper thermal technology not only destructs those persistent organic toxicants but also stabilizes hazardous heavy metals in MSWI fly ash.

Glass-ceramics made from arc-melting slag of waste incineration fly ash

Grate fly ash and fluidized bed fly ash mixed with glass cullet additive respectively were melted in the electronic arc-furnace. The product, arc-melting slag, was further treated by crushing, pressing and heat treatment in order to make the glass-ceramics. The crystallization behaviors of the produced glass-ceramics were examined by differential thermal analysis （DTA）, X-ray diffractometry （XRD） and scanning electron microscopy （SEM）. Results show that main crystalline phase of the glass-ceramics fi＇om grate fly ash is wollastonite （CaSiO3） with small amount of diopside （Ca（Mg,Al）（Si,Al）206）, and that from fluidized bed fly ash is diopside （Ca（Mg,Al）（Si,Al）206）. It is found that the glass-ceramics sintered at 850 ℃and 1 000℃ from grate fly ash and fluidized bed fly ash respectively have the optimal physical, mechanical and chemical characteristics. Glass-ceramics samples, produced from incinerator fly ash with desirable properties and the low leaching concentration of heavy metals, can be the substitute of nature materials such as marble, granite and porcelain tiles.

Mechanism of high concentration phosphorus wastewater treated by municipal solid waste incineration fly ash

The mechanism of removing phosphate by MSWI(municipal solid waste incineration)fly ash was investigated by SEM(scanning electron microscopy)with EDS(energy dispersion spectrum),XRD(X-ray diffraction),FT-IR(Fourier transform infrared spectroscopy),BET(specific surface area),and BJH(pore size distribution).The results indicate that the removal rate of phosphate(100 mg/L)in 50 mL phosphorus wastewater reaches at 99.9% as the dosage of MSWI fly ash being 0.9000 g under room temperature.The specific surface area of MSWI fly ash is less than 6.1 m2/g and the total pore volume is below 0.021 cm3/g,suggesting that the absorption capacity of calcite is too weak to play an important role in phosphate removal.SEM images show that drastic changes had taken place on its specific surface shape after reaction,and EDS tests indicate that some phosphate precipitates are formed and attached onto MSWI fly ash particles.Chemical precipitation is the main manner of phosphate removal and the main reaction is: 3Ca2++2 PO4 3-+xH2O→Ca3(PO4)2↓·xH2O.Besides,XRD tests show that the composition of MSWI fly ash is complex,but CaSO4 is likely to be the main source of Ca2+.The soluble heavy metals in MSWI fly ash are stabilized by phosphate.

Comment on the development and policy of the waste incineration power generation industry

Development space of the waste incineration power generation is expanding. According to the technical route of previous planning and related policies, the principles of our garbage disposal are based on sanitary landfill, supplemented by burning. However, with the accelerated process of urbanization, land resources are increasingly strained and most large cities have been unable to find a suitable landfill within the feasible urban extent, the main equipment for the incinerator and the localization of the overall process greatly reduced its capital investment and these factors will promote the rapid development of waste incineration power generation industry. Waste incineration and power generation technology has the dual benefits of environmental protection and energy and it is the development direction of waste disposal in the future. According to the condition that our country＇s waste incineration power generation started from scratch and developed rapidly in recent years ,there is a introduction about the application of the waste incineration and a brief analysis of the its obstacles in the promotion and financing, as well as the potential for future applications.

Comparative Study on Distributed Waste Pyrolysis Cold Emission Energy Station and Incineration Power Generation

The proper terminal disposal of organic solid waste such as domestic waste is a worldwide issue.Landfill covers a large area,with limited capacity,and a single landfill will be filled one day;incineration is costly to build and operate.These methods all need to transfer and centralized treatment,and secondary pollution is difficult to control,against the purification law of the nature."NIMBY effect"is very serious,and the social cost of treatment is increasing,becoming a heavy financial burden."The Distributed Waste Pyrolysis Cold Emission Energy Station"developed by Hunan Zhongzhou Energy-Saving Technology Co.,Ltd.overcomes these disadvantages and constructs a more appropriate environmental economic industrial chain for the treatment of organic solid waste such as urban and rural household waste.Based on its technical characteristics,this paper compares it with waste incineration power generation project in the aspects of secondary pollution control,treatment effect,energy utilization,investment and operation economy,etc.

Novel Technology and Products: Fluidized Bed Incineration and Energy Recovery for Waste Disposal——Developed by the Institute for Thermal Power Engineering, Zhejiang University

The waste referred to includes solid waste and sludge. Solid waste is mainly from urban garbage and industrial waste. Sludge is from water treatment factories, paper mills, chemical factories, pharmaceutical factories, rivers and lakes. The waste and sludge are very harmful to water organisms, human health and drinking water, and directly affect the environment. Sludge and waste also occupy large areas of land. There are several methods to treat waste and sludge, such as burial, chemical treatment and incineration. Incineration is more effective than the

Analysis of the Relationship between Mechanical Properties and Pore Structure of MSW Incineration Bottom Ash Fine Aggregate Concrete after Freeze-Thaw Cycles Based on the Gray Theory

The destruction of concrete building materials in severely cold regions of the north is more severely affected by freeze-thaw cycles,and the relationship between the mechanical properties and pore structure of concrete with fine aggregate from municipal solid waste(MSW)incineration bottom ash after freeze-thaw cycles is analyzed under the degree of freeze-thaw hazard variation.In this paper,the gray correlation method is used to calculate the correlation between the relative dynamic elastic modulus,compressive strength,and microscopic porosity parameters to speculate on the most important factors affecting their changes.The GM(1,1)model was established based on the compressive strength of the waste incineration ash aggregate concrete,the relative error between the simulated and actual values in the model was less than 5%,and the accuracy of the model was level 1,indicating that the GM(1,1)model can well reflect the change in the compressive strength of the MSW incineration bottom ash aggregate concrete during freeze-thaw cycles.Using the gray correlation method,the correlation between the relative dynamic elastic modulus,compressive strength,air content,specific surface area,pore spacing coefficient,and pore average chord length was calculated,and the pore spacing coefficient and pore average chord length were determined to be highly correlated with each other.This determination can help analyze and infer the deterioration mechanism of concrete subject to freeze-thaw cycles.These results can provide a theoretical basis for guiding the engineering practice of concrete with fine aggregates of household bottom ash in the northern cold region.

HVAC Design Strategies for Municipal Waste Incineration Power Plants

In recent years,relevant government departments have achieved the goal of reduction and harmless application through the development and implementation of municipal waste incineration power plants,in order to advocate ecological and environmental protection.At present,in order to further achieve the goal of sustainable development,municipal waste incineration power plants have actively responded to the national call and requirements as well as made overall arrangements for the energy-saving design and optimization design of their internal system.Therefore,with the concept of sustainable development,this paper studies and analyzes the problems of the HVAC design as well as suggests related strategies for municipal waste incineration power plants in order to provide relevant reference.

Effect of oxide interactions on chromium speciation transformation during simulated municipal solid waste incineration

Chromium released during municipal solid waste incineration(MSWI)is toxic and carcinogenic.The removal of chromium from simulated MSWI flue gas by four sorbents(CaO,bamboo charcoal(BC),powdered activated carbon(PAC),and Al_(2)O_(3))and the effects of four oxides(SiO_(2),Al_(2)O_(3),Fe_(2)O_(3),and CaO)on chromium speciation transformationwere investigated.The results showed that the removal rates of total Cr by the four sorbents were Al_(2)O_(3)<CaO<PAC<BC,while the removal rates of Cr(Ⅵ)by the four sorbents were Al_(2)O_(3)<PAC<BC<CaO.CaO had a strong oxidizing effect on Cr(Ⅲ),while BC and PAC had a better-reducing effect on Cr(Ⅵ).SiO_(2)was better for the reduction of Na_(2)CrO_(4)and K_(2)CrO_(4)above 1000℃due to its strong acidity,and the addition of CaO significantly inhibited the reduction of Cr(Ⅵ).MgCrO_(4)decomposed above 700℃to form MgCr_(2)O_(4),and the reaction between MgCrO_(4)and oxides also existed in the form of a more stable trivalent spinel.Furthermore,when investigating the effect of oxides on the oxidation of Cr(Ⅲ)in CrC_(l3),it was discovered that CaO promoted the conversion of Cr(Ⅲ)to Cr(Ⅵ),while the presence of chlorine caused chromium to exist in the form of Cr(V),and increasing the content of CaO and extending the heating time facilitated the oxidation of Cr(Ⅲ).In addition,silicate,aluminate,and ferrite were generated after the addition of SiO_(2),Al_(2)O_(3),and Fe_(2)O_(3),which reduced the alkalinity of CaO and had an important role in inhibiting the oxidation of Cr(Ⅲ).The acidic oxides can not only promote the reduction of Cr(Ⅵ)but also have an inhibitory effect on the oxidation of Cr(Ⅲ)ascribed to alkali metals/alkaline earth metals,and the proportion of acidic oxides can be increased moderately to reduce the generation of harmful substances in the hazardous solid waste heat treatment.

Chemical speciation and mobility of heavy metals in municipal solid waste incinerator fly ash

Chemical speciation is a significant factor that governs the toxicity and mobility of heavy metals in municipal solid waste incinerator fly ash. Sequential extraction procedure is applied to fractionate heavy metals(Pb, Zn, Cd, Cu, and Cr) into five defined groups: exchangeable, carbonate, Fe-Mn oxide, organic, and residual fractions. The mobility of heavy metals is also investigated with the aid of toxicity characteristic leaching procedure. In the fly ash sample, Pb is primarily presented in the carbonate(51%) and exchangeable(20%) fractions; Cd and Zn mainly exist as the exchangeable(83% and 49% respectively); Cu is mostly contained in the last three fractions(totally 87%); and Cr is mainly contained in the residual fraction(62%). Pb, Zn and Cd showed the high mobility in the investigation, thus might be of risk to the natural environment when municipal solid waste incinerator fly ash is landfilled or reutilized.

Polychlorinated dibenzo-p-dioxins and dibenzofurans in flue gas emissions from municipal solid waste incinerators in China

Polychlorinated dibenzo-p-dioxins and furans （PCDD/Fs） emissions in flue gas from two types of municipal solid waste incinerators （MSWIs） most commonly used in China were investigated in this study. The selected incinerators include two grate-type MSWIs： MSWI-A （350 t/d） and MSWI-B 050 t/d）, and two fluidized bed MSWIs： MSWI-C （400 t/d） and MSWI-D （400 t/d）, which are all equipped with semi-dry lime scrubber and bag filter except MSWI-D equipped with cyclone and wet scrubber （WS） as air pollutant control device （APCD）. Results indicated that the emission concentration and the international toxic equivalents （I-TEQs） of the PCDD/Fs from the stacks were in the range of 1.210-10.273 ng/Nm^3 and 0.019-0.201 ng I-TEQ/Nm^3, respectively. They were greatly lower than the emission regulation standard of PCDD/Fs in China （1.0 ng I-TEQ/Nm^3）. However, only the PCDD/Fs emission level from MSWI-C was below 0.1 ng I-TEQ/Nm^3. Although the homologue profiles were distinct, the contributions of the 2,3,7,8-subsituted congeners to the total I-TEQ were similar among all the investigated MSWIs. Two major 2,3,7,8-substituted congeners, 2,3,4,7,8-PeCDF and 1,2,3,7,8-PeCDD, account for 47% and 9% （average values） of the total I-TEQ values, respectively. The correlation between PCDD/Fs levels and composition of flue gas was also discussed.