Discussion on“Dispersion characteristics of clayey soils containing waste rubber particles”[J Rock Mech Geotech Eng 15(2023)3050-3058]

We read with great interest the recent article by Erenson(2023)entitled“Dispersion characteristics of clayey soils containing waste rubber particles”.The author has studied the dispersion characteristics of clayey soils containing different percentages of waste rubber particles(WRPs)by performing several tests(viz.consistency limit,linear shrinkage limit,double hydrometer,crumb test and pinhole test)and scanning electron microscopy(SEM)analysis on five clayey(viz.Na-activated bentonite,refined ball clay,Ukrainian kaolin,Avanos kaolin and Afyon clay)samples containing 0%,5%,10%and 15%WRPs.It should be noted that Erenson(2023)has presented some interesting observations,but there are some serious issues that we want to share through this discussion and request the author of the original paper to address them to avoid their persistence in the scientific literature.

Dispersion characteristics of clayey soils containing waste rubber particles

The rubber-containing waste materials have been widely used to improve the engineering properties of soils in recent years.Among others,granular rubbers are utilized in various ways to increase the bearing capacity and shear strength and to reduce the settlement and liquefaction potential of soils.The granular rubbers have many advantages such as temperature resistance,flexibility,tear-resistance,non-slip,and thermal and electrical insulation.This study presents the distribution characteristics of five different types of clayey soils with different engineering properties containing waste rubber particles(WRPs).On the other hand,determining and controlling the dispersion characteristics of clayey soils is two significant engineering problems.The study aims to solve these two remarkable and problematic issues in an eco-friendly and safe way.The role of WRP treatment in the investigation of soil dispersion behavior,which can cause dangerous problems such as piping,erosion,and dispersion,reflects the original and different perspectives of this study.Within this scope,geotechnical parameters of the clayey soils were determined.Subsequently,pinhole test,crumb test,double hydrometer test,and scanning electron microscopy(SEM)analysis were performed on the Na-activated bentonite,refined ball clay,Ukrainian kaolin,Avanos kaolin,and Afyon clay samples with different percentages of WRPs(0%,5%,10%,and 15%).Consequently,Avanos and Ukrainian kaolin clays gave the most limited response to the dispersion behavior with the addition of WRP.Also,WRP treatment on the ball clay and bentonite samples showed limited efficiency.Afyon clay,which was defined as dispersive by the three tests that determined its dispersion potential,showed 3 level changes in the pinhole tests and 2 level changes in the crumb tests,and gave the most effective results in terms of WRP efficiency.

Combustion Ratio of Waste Tire Particle, PC and Mixture at Blast Temperature of BF

In order to study the combustion characteristics of waste tire particle （WTP）, pulverized coal （PC） and their mixture, the contents of CO, CO2 and O2 of off-gas during the combustion of WTP, PC and mixture under the condition of rich oxygen by 0--4% in blast and at 1 250℃ were measured simultaneously using synthetically infrared analyzer, and then the corresponding combustion ratio was calculated and compared. The results showed that the burning rate of WTP reached approximately 57%, which is much higher than that of PC （only about 18%） in the in- itial 650 s in fresh air, and then the increase of combustion rate of PC is faster than that of WTP; the combustion rate of PC improved remarkably with the addition of WTP. Meanwhile, the combustion rates of all these materials improved with the increase of oxygen content.

Insights into metals in individual fine particles from municipal solid waste using synchrotron radiation-based micro-analytical techniques

Excessive inter-contamination with heavy metals hampers the application of biological treatment products derived from mixed or mechanically-sorted municipal solid waste（MSW）. In this study, we investigated fine particles of 〈 2 mm, which are small fractions in MSW but constitute a significant component of the total heavy metal content, using bulk detection techniques. A total of 17 individual fine particles were evaluated using synchrotron radiation-based micro-X-ray fluorescence and micro-X-ray diffraction. We also discussed the association, speciation and source apportionment of heavy metals. Metals were found to exist in a diffuse distribution with heterogeneous intensities and intense hot-spots of 〈 10 μm within the fine particles. Zn–Cu, Pb–Fe and Fe–Mn–Cr had significant correlations in terms of spatial distribution. The overlapped enrichment, spatial association, and the mineral phases of metals revealed the potential sources of fine particles from size-reduced waste fractions（such as scraps of organic wastes or ceramics） or from the importation of other particles. The diverse sources of heavy metal pollutants within the fine particles suggested that separate collection and treatment of the biodegradable waste fraction（such as food waste） is a preferable means of facilitating the beneficial utilization of the stabilized products.

Use of multiscale particle simulations in the design of nuclear plant decommissioning

The application of a digital modelling method that can faithfully take account of three-dimensional shape and inherent physical and chemical properties of each particulate component provides an essential tool in decommissioning design. This is useful in handling of high, medium and low level radioactive waste. The processes involve making decisions on where to cut existing plant components and then how to pack these components into boxes, which are then cemented and kept for long term storage as the level of radioactive declines with time. We illustrate the utility of the method and its ability to take data at plant scale （m-scale） and then deduce behaviours at sub millimetre scale in the packed containers. A variety of modelling approaches are used as a part of this approach including cutting algorithms, geometric and dynamic （distinct element） force models, and lattice Boltzmann methods. These methods are applicable to other complex particulate systems including simulation of waste, building recycling, heap leaching and related minerals processes. The paper introduces the basic concepts of this multi-scale and multi-model approach.