Electronic scrap, especially wasted printed circuit boards (PCBs), is regarded as an environmental challenge. At present, the physical separation is thought to be the environmental friendly and economical method of tr...Electronic scrap, especially wasted printed circuit boards (PCBs), is regarded as an environmental challenge. At present, the physical separation is thought to be the environmental friendly and economical method of treating and reutilizing electronic waste. An effective liberation of metals from non metallic components is a crucial step towards mechanical separation and recycling of wasted PCBs. In this paper, the selective shredding theory and mechanics characteristics of wasted PCBs were analyzed, and the shredded experiments of wasted PCBs by hammer mill were investigated. The result shows that the selective shredding exists in the wasted PCBs shredded process by hammer mill. The shredding velocity of non metallic components is far greater than that of metals in the wasted PCBs shredding, which makes the metals concentrate in the coarser fraction. And the impact force of hammer mill is superior to metal liberation from non metallic components, a satisfied metal liberation degree can be achieved in the wasted PCBs shredding by hammer mill.展开更多
The quality of printed circuit board(PCB)micro-hole processing directly determines the stability of the inner and outer circuit connections.Micro-hole drilling technology is a typical method for PCB micro-hole process...The quality of printed circuit board(PCB)micro-hole processing directly determines the stability of the inner and outer circuit connections.Micro-hole drilling technology is a typical method for PCB micro-hole processing.The problem of optimal control of its drilling force is one of the main factors affecting the quality of micro-hole machining.To address this problem,the thrust forces and torques in PCB drilling were first modeled and analyzed,and the corresponding prediction models were established.The drilling force analysis was carried out through the micro-hole drilling experiment,the specific cutting energy under different feed rates was calculated,the influence of the size effect was clarified,and the accuracy of the prediction model was verified.The result shows that during the drilling of glass fiber cloth,changes in the material removal mechanism are induced as the feed per revolution is varied.When the feed per revolution is less than the tool edge radius,the glass fiber is not cut by the main cutting edge,but is crushed and broken.When the feed per revolution is greater than the radius of the tool edge,the glass fiber is cut by the main cutting edge.At the same time,the established analytical model can accurately reflect the influence of the size effect on the drilling torque in PCB micro-hole drilling,and the error is within 10%.This method has certain practical application value in controlling PCB micro hole processing quality.展开更多
Printed circuit boards （PCBs） are in all electronic equipment, so with the sharp increase of electronic waste, the recovery of PCB components has become a critical research field. This paper presents a study of the ...Printed circuit boards （PCBs） are in all electronic equipment, so with the sharp increase of electronic waste, the recovery of PCB components has become a critical research field. This paper presents a study of the reclaimation and reuse of nonmetallic materials recovered from waste PCBs. Mechanical processes, such as crushing, milling, and separation, were used to process waste PCBs. Nonmetallic materials in the PCBs were separated using density-based separation with separation rates in excess of 95%. The recovered nonmetals were used to make models, construction materials, composite boards, sewer grates, and amusement park boats. The PCB nonmetal products have better mechanical characteristics and durability than traditional materials and fillers. The flexural strength of the PCB nonmetallic material composite boards is 30% greater than that of standard products. Products derived from PCB waste processing have been brought into industrial production. The study shows that PCB nonmetals can be reused in profitable and environmentally friendly ways.展开更多
The recycling method and principle of SnO2 from the tin slag of printed circuit boards（PCB） waste were investigated. In this study, pure SnO2 powders were obtained through a multi-step process including ball-milling...The recycling method and principle of SnO2 from the tin slag of printed circuit boards（PCB） waste were investigated. In this study, pure SnO2 powders were obtained through a multi-step process including ball-milling, roasting, dissolving, precipitating, and pickling. The total recovery rate of tin can be up to 91 %. The SnO2 powders obtained is the single phase, and the content of SnO2 is up to 99.9 %. However, the SnO2 particles are easier to agglomerate during the precipitation process. The agglomerate SnO2 particles are about 7.778 lm in mean particle size（D50）. This preparation method presents a viable alternative for the tin slag recycling. The tin is not only recycled, but also reused directly to prepare pure SnO2 powders.展开更多
The method for the recycling of copper from copper chloride solution was developed. This process consists of extraction of copper, purification and particle size reduction. In the first step, reductive metal scraps we...The method for the recycling of copper from copper chloride solution was developed. This process consists of extraction of copper, purification and particle size reduction. In the first step, reductive metal scraps were added to acidic copper chloride waste enchants produced in the PCB industry to obtain copper powder. Composition analysis showed that this powder contained impurities such as Fe, Ni, and water. So, drying and purification were carried out by using microwave and a centrifugal separator. Thereby the copper powder had a purity of higher than 99% and spherical form in morphology. The copper powder size was decreased by ball milling.展开更多
文摘Electronic scrap, especially wasted printed circuit boards (PCBs), is regarded as an environmental challenge. At present, the physical separation is thought to be the environmental friendly and economical method of treating and reutilizing electronic waste. An effective liberation of metals from non metallic components is a crucial step towards mechanical separation and recycling of wasted PCBs. In this paper, the selective shredding theory and mechanics characteristics of wasted PCBs were analyzed, and the shredded experiments of wasted PCBs by hammer mill were investigated. The result shows that the selective shredding exists in the wasted PCBs shredded process by hammer mill. The shredding velocity of non metallic components is far greater than that of metals in the wasted PCBs shredding, which makes the metals concentrate in the coarser fraction. And the impact force of hammer mill is superior to metal liberation from non metallic components, a satisfied metal liberation degree can be achieved in the wasted PCBs shredding by hammer mill.
基金National Natural Science Foundation of China(No.51805079)Fundamental Research Funds for the Central Universities,China(No.2232021D-15)Shanghai Science and Technology Program(No.20DZ2251400)。
文摘The quality of printed circuit board(PCB)micro-hole processing directly determines the stability of the inner and outer circuit connections.Micro-hole drilling technology is a typical method for PCB micro-hole processing.The problem of optimal control of its drilling force is one of the main factors affecting the quality of micro-hole machining.To address this problem,the thrust forces and torques in PCB drilling were first modeled and analyzed,and the corresponding prediction models were established.The drilling force analysis was carried out through the micro-hole drilling experiment,the specific cutting energy under different feed rates was calculated,the influence of the size effect was clarified,and the accuracy of the prediction model was verified.The result shows that during the drilling of glass fiber cloth,changes in the material removal mechanism are induced as the feed per revolution is varied.When the feed per revolution is less than the tool edge radius,the glass fiber is not cut by the main cutting edge,but is crushed and broken.When the feed per revolution is greater than the radius of the tool edge,the glass fiber is cut by the main cutting edge.At the same time,the established analytical model can accurately reflect the influence of the size effect on the drilling torque in PCB micro-hole drilling,and the error is within 10%.This method has certain practical application value in controlling PCB micro hole processing quality.
基金the National High-Tech Research and Development (863) Program of China (No. 2004AA420120)
文摘Printed circuit boards （PCBs） are in all electronic equipment, so with the sharp increase of electronic waste, the recovery of PCB components has become a critical research field. This paper presents a study of the reclaimation and reuse of nonmetallic materials recovered from waste PCBs. Mechanical processes, such as crushing, milling, and separation, were used to process waste PCBs. Nonmetallic materials in the PCBs were separated using density-based separation with separation rates in excess of 95%. The recovered nonmetals were used to make models, construction materials, composite boards, sewer grates, and amusement park boats. The PCB nonmetal products have better mechanical characteristics and durability than traditional materials and fillers. The flexural strength of the PCB nonmetallic material composite boards is 30% greater than that of standard products. Products derived from PCB waste processing have been brought into industrial production. The study shows that PCB nonmetals can be reused in profitable and environmentally friendly ways.
基金financially supported by the Beijing Nova Program (No. Z141103001814006)the National Key Technology R&D Program (Nos. 2012BAC12B05 and 2012BAC02B01)+1 种基金the National Natural Science Foundation of China (Nos. 51174247 and U1360202)the National High-Tech Research and the Development Program of China (No. 2012AA063202)
文摘The recycling method and principle of SnO2 from the tin slag of printed circuit boards（PCB） waste were investigated. In this study, pure SnO2 powders were obtained through a multi-step process including ball-milling, roasting, dissolving, precipitating, and pickling. The total recovery rate of tin can be up to 91 %. The SnO2 powders obtained is the single phase, and the content of SnO2 is up to 99.9 %. However, the SnO2 particles are easier to agglomerate during the precipitation process. The agglomerate SnO2 particles are about 7.778 lm in mean particle size（D50）. This preparation method presents a viable alternative for the tin slag recycling. The tin is not only recycled, but also reused directly to prepare pure SnO2 powders.
文摘The method for the recycling of copper from copper chloride solution was developed. This process consists of extraction of copper, purification and particle size reduction. In the first step, reductive metal scraps were added to acidic copper chloride waste enchants produced in the PCB industry to obtain copper powder. Composition analysis showed that this powder contained impurities such as Fe, Ni, and water. So, drying and purification were carried out by using microwave and a centrifugal separator. Thereby the copper powder had a purity of higher than 99% and spherical form in morphology. The copper powder size was decreased by ball milling.
