Application of Ice Pigging in a Drinking Water Distribution System:Impacts on Pipes and Bulk Water Quality

Ice pigging is an emerging technique for pipe cleaning in drinking water distribution systems.However,substantial confusion and controversy exist on the potential impacts of ice pigging on bulk water quality.This study monitored the microstructural features and composition of sediments and microbial community structures in bulk water in eight multimaterial Chinese networks.Chloride concentration analysis demonstrated that separate cleaning of pipes with different materials in complex networks could mitigate the risk of losing ice pigs and degrading water quality.The microstructural and trace element characterization results showed that ice pigs would scarcely disturb the inner surfaces of long-used pipes.The bacterial richness and diversity of bulk water decreased significantly after ice pigging.Furthermore,correlations were established between pipe service age,temperature,and chloride and total iron concentrations,and the 15 most abundant taxa in bulk water,which could be used to guide practical ice pigging operations.

Remaining oil distribution characteristics in an oil reservoir with ultra-high water-cut

An accurate mapping and understanding of remaining oil distribution is very important for water control and stabilize oil production of mature oilfields in ultra-high water-cut stage.Currently,the Tuo-21 Fault Block of the Shengtuo Oilfield has entered the stage of ultra-high water cut(97.2%).Poor adaptability of the well pattern,ineffective water injection cycle and low efficiency of engineering measures(such as workover,re-perforation and utilization of high-capacity pumps)are the significant problems in the ultra-high water-cut reservoir.In order to accurately describe the oil and water flow characteristics,relative permeability curves at high water injection multiple(injected pore volume)and a semiquantitative method is applied to perform fine reservoir simulation of the Sand group 3e7 in the Block.An accurate reservoir model is built and history matching is performed.The distribution characteristics of remaining oil in lateral and vertical directions are quantitatively simulated and analyzed.The results show that the numerical simulation considering relative permeability at high injection multiple can reflect truly the remaining oil distribution characteristics after water flooding in an ultrahigh water-cut stage.The distribution of remaining oil saturation can be mapped more accurately and quantitatively by using the‘four-points and five-types’classification method,providing a basis for potential tapping of various remaining oil types of oil reservoirs in late-stage of development with high water-cut.

Modeling of residual chlorine in water distribution system

Water quality within water distribution system may vary with both location and time. Water quality models are used to predict the spatial and temporal variation of water quality throughout water system. A model of residual chlorine decay in water pipe has been developed, given the consumption of chlorine in reactions with chemicals in bulk water, bio films on pipe wall, in corrosion process, and the mass transport of chlorine from bulk water to pipe wall. Analytical methods of the flow path from water sources to the observed point and the water age of every observed node were proposed. Model is used to predict the decay of residual chlorine in an actual distribution system. Good agreement between calculated and measured values was obtained.

Online location of seismic damage to a water distribution system

As one of the most important urban lifeline systems,a water distribution system can be damaged under a strong earthquake,and the damage cannot easily be located,especially immediately after the event.This often causes tremendous difficulties to post-earthquake emergency response and recovery activities.This paper proposes a methodology to locate seismic damage to a water distribution system by monitoring water head online at some nodes in the water distribution system.An artificial neural network-based inverse analysis method is developed to estimate the water head variations at all nodes that are not monitored based on the water head variations at the nodes that are monitored.The methodology provides a quick,effective,and practical way to locate seismic damage to a water distribution system.

Multi-objective Optimisation Design of Water Distribution Systems:Comparison of Two Evolutionary Algorithms

In order to compare two advanced multi-objective evolutionary algorithms,a multi-objective water distribution problem is formulated in this paper.The multi-objective optimization has received more attention in the water distribution system design.On the one hand the cost of water distribution system including capital,operational,and maintenance cost is mostly concerned issue by the utilities all the time;on the other hand improving the performance of water distribution systems is of equivalent importance,which is often conflicting with the previous goal.Many performance metrics of water networks are developed in recent years,including total or maximum pressure deficit,resilience,inequity,probabilistic robustness,and risk measure.In this paper,a new resilience metric based on the energy analysis of water distribution systems is proposed.Two optimization objectives are comprised of capital cost and the new resilience index.A heuristic algorithm,speedconstrained multi-objective particle swarm optimization( SMPSO) extended on the basis of the multi-objective particle swarm algorithm,is introduced to compare with another state-of-the-art heuristic algorithm,NSGA-II.The solutions are evaluated by two metrics,namely spread and hypervolume.To illustrate the capability of SMPSO to efficiently identify good designs,two benchmark problems( two-loop network and Hanoi network) are employed.From several aspects the results demonstrate that SMPSO is a competitive and potential tool to tackle with the optimization problem of complex systems.

Water System Condition and Asset Replacement Prioritization

The goal of asset management is to identify and track the maintenance and replacement of assets that have reached their useful life. For that reason, gathering data and collecting information is a critical step when developing an asset management plan. Such data gathering includes physical and operational properties of the assets as well as collecting and tracking important events during the lifespan of the asset (i.e., pipe breaks, replacement year, maintenance performed, etc.). Critical factors in the asset management plan may be overlooked when there is no data or poor quality data. However, many utilities lack the resources for examining buried infrastructure and lack good quality work order data, so other methods of data collection are needed. The concept for this paper was to develop a means to acquire data on the assets for a condition assessment to identify pipes that were most likely to break and those with the highest consequences for same. Three utilities were used as examples. It was found that for buried infrastructure, much more information was known than anticipated but the actual predictions relied on only a few factors related to pipe type. However, there is a need to track the consequences, in this case breaks, which would indicate a failure. The latter would be useful for predicting future maintenance needs and the most at-risk assets, but is often missing in utility systems as many utilities do not adequately track breaks sufficiently. In this case two utilities were analyzed and predication on a third was developed.

Iron stability in drinking water distribution systems in a city of China

A field study on the estimation and analysis of iron stability in drinking water distribution system was carried out in a city of China. The stability of iron ion was estimated by pC-pH figure. It was found that iron ion was unstable, with a high Fe （OH）3 precipitation tendency and obvious increase in turbidity. The outer layer of the corrosion scale was compact, while the inner core was porous. The main composition of the scale was iron, and the possible compound constitutes of the outer scale were α-FeOH, γ-FeOOH, α-Fe2O3, γ-F2O3, FeCl3, while the inner were Fe3O4, FeCl2, FeCO3. According to the characteristics of the corrosion scale, it was thought that the main reason for iron instability was iron release from corrosion scale. Many factors such as pipe materials, dissolved oxygen and chlorine residual affect iron release. Generally, higher iron release occurred with lower dissolved oxygen or chlorine residual concentration, while lower iron release occurred with higher dissolved oxygen or chlorine residual concentration. The reason was considered that the passivated out layer of scale of ferric oxide was broken down by reductive reaction in a condition of low oxidants concentration, which would result more rapid corrosion of the nine and red water phenomenon.

Root distribution and influencing factors of dry-sowing and wet-growing cotton plants under different water conditions

To study the effect of soil water and salt environment factors on the root growth of cotton under different moisture control,three different emergence water volumes(60,105,and 150 m^(3)/hm^(2)),two different frequencies(high frequency and low frequency)and one double film cover winter irrigation control treatment(CK:2250 m^(3)/hm^(2))were set up to analyze the spatial distribution patterns of soil water and salt environment and root density in dry sown and wet emerged cotton fields under diffe-rent moisture control conditions.The results show that the soil water content and water infiltration range gradually become larger with the increase of seedling water quantity,and the larger the seedling water quantity,the higher the soil water content.With the same seedling water quantity,the soil water content of the high-frequency(HF)treatment becomes obviously larger.The soil conductivity of each treatment tends to decrease gradually with the increase of seedling water and drip frequency,among which the distribution of soil conductivity of S6 treatment is closest to that of CK.With the increase in soil depth,the soil conductivity tends to increase first and then decrease.Compared with the low-frequency(LF)treatment,the high-frequency treatment shows a significantly deeper soil salt accumulation layer.The root length density(RLD)of cotton gradually increases with the amount of seedling water and the frequency of dripping.The soil layer of root distribution gradually deepens with the amount of seedling water in the vertical direction,and the RLD value in the horizontal direction is significantly greater in the mulched area than that in the bare area between films.This research can serve as a solid scientific foundation for the use of dry sowing and wet emergence techniques in cotton fields in southern Xinjiang.

Comparison of Using an Electronic System and Conventional Monitoring Method for Monitoring the Quality of Drinking Water and Defects Discovery in Rural Area Water Distribution Network of Abarkouh, Iran

The used water for human consumption must be free of microorganisms and chemicals that cause risk in the human health. In this study, water quality of 18 rural area of Abarkouh was determined and compared the conventional monitoring method (According to ISIR (Institute of Standards and Industrial Research of Iran), 1053 and 4208) and use of electronic system method (Patent in industrial property general office of Iran, 77815). Free chlorine monitoring and pH test done by health workers in the conventional method and the results will be sent to the Health Network monthly. Sampling for microbiological testing is done monthly based on population (According to ISIR, 4208). On the electronic system, the procedure is also done by health workers, but the result will be sent to the receiver device by using a cell phone. According to the chlorine test results if the free chlorine residual reported zero, microbiological sampling was done by a health expert. Finally, the number of chlorine test and microbiological sampling and the results of these experiments collected in the both methods and recorded in SPSS 22 then were analyzed by using chi-square test and Fisher exact test. The result of microbiological experiments shows that the sampling rate decreased 29% in using of electronic system method in comparison to the conventional monitoring method while the number of microbial defect detection increased 19% in drinking water networks monitoring by electronic system. Using of electronic system monitoring can reduce the rate and cost of microbiological sampling and its experiments and increase accuracy of these tests, in this way it will increase the quality and safety of drinking water in distribution network in small and dispersed rural communities.

Analysis on Biological Stability and Influencing Factors of Northern Living District Water Distribution System

A northern living strict water network was employed to investigate interaction among biological stability and classical water quality indexes. Key water quality indexes on water quality were determined by the static test,then the correlations between biological stability and traditional water quality parameters were analyzed. Traditional water quality parameters and limited factors on bacteria were measured in summer and winter respectively. The results show that BDOC concentration change differently in summer and winter.Among classical parameters turbidity has a positive relation with BDOC but pH has a negative relation with BDOC. Total bacteria number shows a positive correlation with BDOC in the water distribution system.Residual chlorine shows a negative relation with total bacteria number. Fe content increasing will induce turbidity rising in water. To guarantee water safety,BDOC and chlorine content control must be incorporated together to restrict bacteria regrowth.

Seismic Reliability and Rehabilitation Decision of Water Distribution System

In order to evaluate the seismic reliability of water distribution system and make rehabilitation decisions correspondingly, it is necessary to assess pipelines damage states and conduct functional analysis based on pipe leakage model. When an earthquake occurred, the water distribution system kept serving with leakage. By adding a virtual node at the centre of the pipeline with leakage, an efficient approach to pressure-driven analysis was developed for simulating a variety of low relative scenarios, and a hydraulic leakage model was also built to perform hydraulic analysis of the water supply network with seismic damage. Then the mean-first-order-second-moment method was used to analyse the seismic serviceability of the water distribution system. According to the assessment analysis, pipes that were destroyed or in heavy leakage were isolated and repaired emergently, which improved the water supply capability of the network and would constitute the basis for enhancing seismic reliability of the system. The proposed approach to seismic reliability and rehabilitation decision analysis on water distribution system is demonstrated effective through a case study.

Partial Least Squares Regression Model to Predict Water Quality in Urban Water Distribution Systems

The water distribution system of one residential district in Tianjin is taken as an example to analyze the changes of water quality.Partial least squares(PLS) regression model,in which the turbidity and Fe are regarded as control objectives,is used to establish the statistical model.The experimental results indicate that the PLS regression model has good predicted results of water quality compared with the monitored data.The percentages of absolute relative error(below 15%,20%,30%) are 44.4%,66.7%,100%(turbidity) and 33.3%,44.4%,77.8%(Fe) on the 4th sampling point;77.8%,88.9%,88.9%(turbidity) and 44.4%,55.6%,66.7%(Fe) on the 5th sampling point.

Assessment on reliability of water quality in water distribution systems

Water leaving the treatment works is usually of a high quality but its properties change during the transportation stage. Increasing awareness of the quality of the service provided within the water industry today and assessing the reliability of the water quality in a distribution system has become a major significance for decision on system operation based on water quality in distribution networks. Using together a water age model, a chlorine decay model and a model of acceptable maximum water age can assess the reliability of the water quality in a distribution system. First, the nodal water age values in a certain complex distribution system can be calculated by the water age model. Then, the acceptable maximum water age value in the distribution system is obtained based on the chlorine decay model. The nodes at which the water age values are below the maximum value are regarded as reliable nodes. Finally, the reliability index on the percentile weighted by the nodal demands reflects the reliability of the water quality in the distribution system. The approach has been applied in a real water distribution network. The contour plot based on the water age values determines a surface of the reliability of the water quality. At any time, this surface is used to locate high water age but poor reliability areas, which identify parts of the network that may be of poor water quality. As a result, the contour water age provides a valuable aid for a straight insight into the water quality in the distribution system.

Leak Detection in Water Distribution Systems Using Bayesian Theory and Fisher’s Law

A leak detection method based on Bayesian theory and Fisher’s law was developed for water distribution systems. A hydraulic model was associated with the parameters of leaks (location, extent). The randomness of parameter values was quantified by probability density function and updated by Bayesian theory. Values of the parameters were estimated based on Fisher’s law. The amount of leaks was estimated by back propagation neural network. Based on flow characteristics in water distribution systems, the location of leaks can be estimated. The effectiveness of the proposed method was illustrated by simulated leak data of node pressure head and flow rate of pipelines in a test pipe network, and the leaks were spotted accurately and renovated on time.

Kinetics of Chlorine Decay in Water Distribution Systems

A combined first and second-order model, which includes bulk decay and wall decay, was developed to describe chlorine decay in water distribution systems. In the model the bulk decay has complex relationships with total organic carbon (TOC), the initial chlorine concentration and the temperature. Except for the initial stages they can be simplified into a linear increase with TOC, a linear decrease with initial chlorine concentration and an exponential relationship with the temperature. The model also explains why chlorine decays rapidly in the initial stages. The parameters of model are determined by deriving the best fitness with experimental data. And the accuracy of model has been verified by using the experimental data and the monitoring data in a distribution system.

Disadvantage Pressure Changes on the Decline of Water Quality in Water Distribution Systems

Systems that have big transmission line may have problem on changes of pressure in the distribution system. Because pressure rate changes have been too much between water treatment plant and dead ends in distribution system. This study is to analyze the effects pressure changes on the water quality in water distribution systems. It is located in south west of Ahwaz in IRAN. Ahwaz has five water treatment plants. In Ahwaz, two methods will be utilized. In the first method, samples will be taken from different locations in other to examine the quality of water in the distribution systems and the other method involves the use of simulation of models EPANET. Based on the EPANET model analysis of the water distribution system of Ahwaz as shown in result above the systems has large transmission line and exten- sive networks. So, the distance travelled and residence times have been causing to increase bacterial growth (HPC), chlorine consumption and hydraulic change (pressure) in water distribution system in Ahwaz. Pressure has a reversed relationship with bacterial growth (HPC) and Pressure has a direct relationship with residual chlorine. Pressure change has been causing to increase chlorine consumption more. So, Kw hasn’t any relationship with pressure and bacterial growth (HPC). The result of pressure changes among others can decrease in chlorine content and hydraulic factors, because the systems may be extensive and thus possess complex networks and hangs in quantity cause pressure of flow. Hence hydraulic changes (pressure) could affect of water quality in the water distribution system.

Variability of micropollutants and microorganisms in water distribution system

The variation of water quality in water distribution system was investigated with assimilable organic carbon (AOC)and trihalomethanes(THMs) used as assessment indexes. Bacterium was identified in water distribution. The result showed that there were pathogenic parasites in water distribution system. The variation of AOC is related to chlorine residual and bacterium activity, and AOC concentration decreased first and then increased with the extension of water distribution system. The formation of THMs was related to the consumption of chlorine inside the distribution system, and THMs concentration increased with the extension of water pipe line.

Bacterial Communities Associated with An Occurrence of Colored Water in An Urban Drinking Water Distribution System

This study aimed to investigate bacterial community in an urban drinking water distribution system （DWDS） during an occurrence of colored water. Variation in the bacterial community diversity and structure was observed among the different waters, with the predominance of Proteobacteria. While Verrucomicrobia was also a major phylum group in colored water. Limnobacter was the major genus group in colored water, but Undibacterium predominated in normal tap water. The coexistence of Limnobacter as well as Sediminibacterium and Aquobocterium might contribute to the formation of colored water.

Study on hydrodynamics associated with quality of water in water distribution system

The quality of water in water distribution system may vary with both location and time. Water quality models were used to predict spatial and temporal variation of water quality throughout the water system. Before analyzing the variations of water quality, it is necessary to determine the hydrodynamics in water distribution system. Analytical methods for the flow path from water sources to the observed point and water age of every observed node are proposed. This paper makes a further study on water supply route of multi-sources water supply network system. These studies have been applied to an actual water distribution system.

Effect of droplet characteristics on liquid-phase distribution in spray zone of internal mixing air-mist nozzle

In continuous casting production,droplet characteristics are important parameters for evaluating the nozzle atomization quality,and have a significant impact on the secondary cooling effect and the slab quality.In order to study the behavior of atomized droplets after reaching the slab surface and to optimize the spray cooling effect,the influence of droplet diameter and droplet velocity on the migration behavior of droplets in the secondary cooling zone was analyzed by FLUENT software.Results show that the droplets in the spray zone and on the slab surface are mainly concentrated in the center,thus,the liquid volume fraction in the center is higher than that of either side.As the droplet diameter increases,the region of high liquid volume fraction on the slab surface becomes wider,and the liquid phase distribution in the slab width direction becomes uneven.Although increasing the droplet velocity at the nozzle exit has little effect on droplet diffusion in the spray zone,the distribution becomes more uneven due to more liquid reaches the slab surface per unit time.A prediction formula of the maximum water flow rate on the slab surface for specific droplet characteristics was proposed based on dimensionless analysis and validated by simulated data.A nozzle spacing of 210 mm was recommended under the working conditions in this study,which ensures effective coverage of the spray water over the slab surface and enhances the distribution uniformity of water flow rate in the transverse direction.