Microwave absorption and thermal properties of coral-like SiC aerogel composites prepared by water glass as a silicon source

As a heat-resistant wave-absorbing material,silicon carbide(SiC)aerogel has become a research hotspot at present.However,the most common silicon sources are organosilanes,which are costly and toxic.In this work,SiC aerogels were successfully prepared by using water glass as the silicon source.Specifically,the microstructure and chemical composition of SiC aerogels were controlled by adjusting the Si to C molar ratio during the sol–gel process,and the effect on SiC aerogel microwave absorption properties was investigated.The SiC aerogels prepared with Si:C molar ratio of 1:1 have an effective electromagnetic wave absorption capacity,with a minimum reflection loss value of-46.30 dB at 12.88 GHz and an effective frequency bandwidth of 4.02 GHz.They also have good physical properties,such as the density of0.0444 g/cm^(3),the thermal conductivity of 0.0621 W/(m·K),and the specific surface area of 1099 m^(2)/g.These lightweight composites with microwave-absorbing properties and low thermal conductivity can be used as thermal protection materials for space shuttles and reusable carriers.

STUDY ON THE MUTUAL SOLUBILITY OF WATER GLASS AND WATER SOLUBLE ORGANIC BINDER

The careful studies have been made into the mutual solubility of water glass and water soluble organic binder in this paper, By means of many experiments, it has been found that water soluble polymer is able to be evenly soluble in water glass, and certain valuable conclusions have been concluded.

Preparation and Characterization of CA-MA Eutectic/Silicon Dioxide Nanoscale Composite Phase Change Material from Water Glass via Sol-Gel Method

This work mainly involved the preparation of a nano-scale form-stable phase change material（PCM） consisting of capric and myristic acid（CA-MA） binary eutectic acting as thermal absorbing material and nano silicon dioxide（nano-SiO_2） serving as the supporting material. Industrial water glass for preparation of the nano silicon dioxide matrix and CA-MA eutectic mixture were compounded by single-step sol-gel method with the silane coupling agent. The morphology, chemical characterization and form stability property of the composite PCM were investigated by transmission electron microscopy（TEM）, scanning electron microscopy（SEM）, Fourier-transform infrared（FT-IR） spectroscopy and polarizing microscopy（POM）. It was indicated that the average diameter of the composite PCM particle ranged from 30-100 nm. The CA-MA eutectic was immobilized in the network pores constructed by the Si-O bonds so that the composite PCM was allowed no liquid leakage above the melting temperature of the CA-MA eutectic. Differential scanning calorimetry（DSC） and thermogravimetric analysis（TGA） measurement were conducted to investigate the thermal properties and stability of the composite PCM. From the measurement results, the mass fraction of the CA-MA eutectic in the composite PCM was about 40%. The phase change temperature and latent heat of the composite were determined to be 21.15 ℃ and 55.67 J/g, respectively. Meanwhile, thermal conductivity of the composite was measured to be 0.208 W·m^（-1）·K^（-1） by using the transient hot-wire method. The composite PCM was able to maintain the surrounding temperature close to its phase change temperature and behaved well in thermalregulated performance which was verified by the heat storage-release experiment. This kind of form-stable PCM was supposed to complete thermal insulation even temperature regulation by the dual effect of relatively low thermal conductivity and phase change thermal storage-release properties. So it can be formulated that the nanoscale CA-MA/SiO_2 composite PCM with the form-stable property, good thermal storage capacity and relatively low thermal conductivity can be applied for energy conservation as a kind of thermal functional material.

Influences of SiO2/Na2O Molar Ratio on Aging and Chemical Modification of Water Glass

In this paper, the content of water glass before and after adding modifying agent was measured by Trimethylsilyl-gas-chromatography. The experimental results showed that different modulus of water glass could generate different content of mono-silicate acid and oligomeric silicate acid in water glass. After a period of storage, different modulus of water glass led to decrease of silicate content at different levels. Because higher content of Na2O in water glass tended to incur the alkaline polymerization, the occurrence of depolymerization of silicate species would lead to an increase of oligomeric silicate species, resulting in a drawback of silicate species content after a period of storage. And contrary to that, lower content of Na2O in water glass tended to incur the acidic polymerization. When the modifying agent was added to the newly made water glass, the amount of mono-silicate acid and oligomeric silicate acid also decreased. In modified water glass, the change of each silicate acid species was less than that in unmodified water glass. These results showed that the modifying agent retarded the aging of water glass. It had remarkable significance on the theory and practical application of water glass chemistry.

Water shutoff model test in water-rich sandy stratum by phosphoric acid-water glass grout

The rheological behavior of phosphoric acid-water glass grout in different mixing ratios was studied. Grout made of water glass with Baume degree of 20° and 13.4% phosphoric acid by 1:1 volume ratio is found to be more effective in stopping water. Laboratory model test of water shutoff by grouting was conducted. Test results show that the diffusion length and water cutoff effect of the grout are significantly improved as the grout head is raised, due to the dilution of underground water, and it takes the grout longer than its gel time to cut off water.

Influence of wet activation of used inorganic binder on cyclically refreshed water glass moulding sands hardened by microwaves

The paper presents the research results of using an innovative method to reclaim the waste moulding sands containing water glass. Two of the examined processes are connected with "dry" or "wet" activation of inorganic binder in waste moulding sand mixtures physically hardened by microwave radiation. The sand mixtures consisting of high-silica sand and water-glass with average molar module 2.5, were subjected to the following cyclical process: mixing the components, compacting, microwave heating, cooling-down, thermally loading the mould to 800 °C, cooling-down to ambient temperature, and knocking-out. After being knocked-out, the waste moulding sands were subjected to either dry or wet activation of the binder. To activate thermally treated inorganic binder, each of the examined processes employed the surface phenomenon usually associated to mechanical reclamation. The study also covered possible use of some elements of wet reclamation to rehydrate waste binder. To evaluate the effectiveness of the two proposed methods of waste binder activation, selected strength and technological parameters were measured. After each subsequent processing cycle, the permeability, tensile strength and bending strength were determined. In addition, the surface of activated sand grains was examined with a scanning electron microscope. Analysis of the results indicates that it is possible to re-activate the used binder such as sodium silicate, and to stabilize the strength parameters in both activation processes. Permeability of the refreshed moulding sands strongly depends on the surface condition of high-silica grains. The wet activation process by wetting and buffering knocked-out moulding sands in closed humid environment makes it possible to reduce the content of refreshing additive in water-glass. The moulding sands cyclically prepared in both processes do not require the addition of fresh high-silica sand. The relatively high quality achieved in the refreshed moulding sands allows them to be reused for manufacture of next moulds. Thus, the two proposed methods for cyclically processing used moulding sands containing sodium silicate, subject to microwave hardening, are suitable for economic and ecological circulation moulding mixtures.

Recycling water glass from wet reclamation sewage of waste sodium silicate-bonded sand

Wet reclamation of waste sodium silicate-bonded sand produces much alkaline sewage and causes pollution. Recycling water glass from wet reclamation sewage of the waste sodium silicate-bonded sand can solve pollution issues and generate economic benefits. In this work, the wet reclamation sewage was filtered, and the filtrate was causticized with a quicklime powder to produce a lye. The effects of causticization temperature, causticization time, and the amount of quicklime powder on the causticization rate were studied. The lye was used to dissolve the silica in the filtration residue to prepare a sodium silicate solution. The effects of the mass of filtration residue, dissolution temperature, and dissolution time on sodium silicate modulus were studied. Finally, the recycled water glass was obtained by concentrating the sodium silicate solution, and the bonding strength of the recycled water glass was tested. The results showed that the causticization rate could be improved by increasing the amount of quicklime powder, causticization temperature, and causticization time, and the highest causticization rate was above 92%. Amorphous silica in the filtration residue dissolved in the lye. Increasing the amount of the filtration residue, dissolution temperature, and dissolution time could improve the sodium silicate modulus. The bonding strength of the recycled water glass was close to that of commercial water glass. The recycled water glass could be used as a substitute for the commercial water glass.

Hydrothermal Dissolution of Opal in Sodium Hydroxide Lyes for the Synthesis of Water Glass

Common opal was dissolved in NaOH lyes in rotating autoclaves. The starting material was characterized by X-ray diffraction and adsorption spectroscopy, thermal and chemical analysis, electron and atomic force microscopy. The opal proved to be an Opal-CT with a microstructure consisting of microcrystalline tridymite, traces of low-quartz, and amorphous parts built up by random packings of size distributed amorphous silica colloids. The dissolution conditions have been inspired by the technological process of hydrothermal water glass synthesis by dissolving silica. Temperature and time of the dissolution process as well as initial molar SiO2:Na2O (Rm) ratios of the starting materials were varied systematically. The particle size of the samples was varied, too, but due to the nanoscopic microstructure without greater impact on dissolution kinetics. The process products were analyzed chemically. Additionally, some of them were characterized by X-ray diffraction, viscosimetry and dynamic light scattering. Already after short dissolution times, water glasses with quite high silica concentrations of up to 27 wt.% and SiO2:Na2O ratios of up to 3.7 were obtained. At longer dissolution times low-quartz and analcime precipitated and the SiO2 contents were reduced to about 22 wt.% and Rm to about 2.7. The silica contents in equilibrium with low-quartz were almost independent on temperature.

Development of Modified Glasses by Transparent, Functional Hybrid Sol-Gel Nano-Ceramic Coatings, a Comparative Study

This paper concentrates on the development of glasses with self-cleaning surfaces exhibiting high water contact angles. In this study, we prepared super-hydrophobic nano-ceramic coated glass based on titania & silica using simple sol-gel & dip coating methods and studied the best composition of the coatings by altering ratios of titanium tetraisopropoxide (TTIP)/tetraethyl orthosilicate (TEOS) with different homogenizing agents. We characterized the coatings by surface roughness measurement, percentage of optical transmission, static contact angle, near-infrared (NIR) transmission, and diffuse reflectance. The fabrication of coatings on glass substrates played an important role in increasing the water contact angle of about 95° and visible & NIR transmission of about 90%. We compared our modified glass substrate with commercial low emissivity (Low E) glass using X-ray diffraction (XRD) analysis, which showed pure amorphous surface claiming excellent wettability and thus the prepared glass substrate could have a variety of applications in different fields.

Test for the effects of three surfactants on the penetration ability of the calcium chloride and water glass Solutions in dust

By using a downward penetration testing device, a large number of experiments were made to investigate the effects of surfactants (sodium succinate, sodium dodecyl sulfonate and dodecyl benzene sulfonic acid sodium salt) on the penetration ability of the calcium chloride and water glass solutions in four dust samples. The experimental results showed that the surfactants can enhance the penetration ability and decrease the surface tension of the calcium chloride and water glass solutions in great extent. After adding the surfactants in 0.2—0.6 wt.% to the solutions of calcium chloride and water glass in 5—25 wt.% respectively, the largest percent of penetration ability increases to 28% more. Among the three surfactants, the size of their effects on the penetration ability of calcium chloride and water solutions in the dust samples is dodecyl benzene sulfonic acid sodium salt, sodium dodecyl sulfonate and sodium succinate.The achieved conclusions are great significant for calcium chloride and water glass to be applied in the field of soil stabilization and raising dust control.

Effect of Water Washing Pre-treatment on the Properties of Glass-ceramics from Incinerator Fly Ash Using Electronic Arc Furnace

Production of glass-ceramics by sintering the molten slag obtained from electric arc furnace treatment of fly ash was investigated. The effect of washing pretreatment prior to melting the fly ash on the microstructure and properties of the glass-ceramics was examined. The results show that washing pretreatment of fly ash can decrease alkali metal chloride and increase network former in fly ash, which results in the increase of peak crystallization temperature of parent glass and strengthening of properties of bending strength and chemical stability of the glass-ceramics. The optimal heat treatment temperature for parent glass of washed fly ash is 1 173 K, at which the crystalline phase of glass-ceramics is composed of gelignite （Ca2A12SiO7） and akermanite （Ca2MgSi207）. Glass-ceramics produced at optimal heat treatment temperature are excellent in term of the physical and chemical properties and leaching characteristics, indicating attractive potential as substitute of nature materials.

Bulk metallic glass rings prepared by a modified water quenching method

Bulk metallic glass rings have the potential applications as annular gasket and active solder in special fields. The bulk metallic glass ring of ZГ41.2Ti13.8Cu12.5Ni10.0Be22.5 with the outer diameter, the inner diameter, and the thickness of 38, 36, and 5 mm, respectively, was prepared by using a special shaped quartz tube water quenching method. The mechanical properties along the whole cross section were investigated by a nanoindentation method, and no evident variation of the Young＇s modulus and hardness was found, further indicating the single amorphous structure. Amorphous ring and tube-shape parts with different dimensions can be produced by this method.

Adsorption Behavior of a Water-soluble Porphyrin at the Glass-water Interface as Studied by Synchronous Total Internal Reflection Fluorescence Spectroscopy

Total internal reflection fluorescence spectroscopy (TIRF) and synchronous scanning technique were combined to study the adsorption behavior of the meso-tetrakis (4-sulfonatophenyl) porphyrin (TPPS) at the glass-water interface without any surfactant. The pH dependence of synchronous fluorescence signal at the interface was analyzed. Both unprotonated (TPPS4-) and diprotonated (H2TPPS2-) forms of TPPS were observed at the interface. But the interface favored the adsorption of. The apparent estimated pKa2 value shifted from 5.00 in the bulk solution to 2.7 at the interface. STIRF provides a good technique to study multi-component systems at the interface.

Performance of Water in Glass Evacuated Tube Solar Water Heater under Kenya Climatic Condition

Solar water heaters which provide a cost-effective and environmental friendly approach to hot water generation are in widespread application. Evacuated tube solar water heaters perform better than flat plate solar water heaters as a result of their greater surface area exposed for sunlight absorption. Water-in-glass evacuated tube solar water heaters are widely used as compared to heat-pipe solar water heaters due to their short payback periods. In this study, the performance of water-in-glass evacuated tube solar water heater is investigated through experiments under the climatic conditions in Kenya. The results revealed a daily efficiency range of 0.58 - 0.65 and a daily final outlet temperature greater than 55°C given an initial temperature of 25°C.

The Mixed-Alkali Effect on The Resistance of Glass to Water

Based on the composition of float glass, the resistance of glassto water, in which a small amount of K_2O(0-1.0 wt/100)wassubstituted for equivalent amount of Na_2O, was investigated by meansof glass grains testing. The components extracted from the glass andtotal alkalinities in extraction solution were de- termined by atomicabsorption spectroscopy and neutralizing method, respectively. Thecomposition of the glass was 14.4 K_2O+ Na_2O, 4.0 MgO, 8.2 CaO, 1.4Al_2O_3, 72.0 SiO, and the minimum extraction radio of oxides(maximum durability)occurred at a K_2O/Na_2O radio of 0.051(byweight)due to the presence of the mixed- alkali effect.

Heat resistance and water protection effectiveness for large single-pane fireproof glass

The effects and heat transfer mode of water film and sprinkler system on the heat-resistant property associated with the insulation of a fireproof glass were investigated. In the experiments, fireproof glass with a size of 3 300 mm (height) × 2 200 mm (width) × 12 mm (thickness) was exposed to an oil pool fire with a power of approximately 1.4 MW. The experimental results show that the application of the water film or sprinkler system on the glass can effectively resist the intensive heat from the fire in the test due to the absorption of latent heat. The permitted period of integrity and insulation with a water film and a sprinkler system could be extended to 60 min. It should be noted that the temperature of the glass surface can be kept under 60 °C in a 60 min test. The experimental results suggest that it is feasible to substitute fireproof glass with water film for a fireproof door as long as the water film or sprinkler system can work stably and water can cover the whole surface of the fireproof glass.

矿粉-再生微粉-水玻璃旧砂超细粉磨协同制备地聚合物试验研究

为研究矿粉-再生微粉-水玻璃旧砂超细粉磨协同制备地聚合物的可行性,开展了粉磨参数、不同再生微粉掺量、不同粉磨细度,不同赤泥掺量下的地聚合物力学性能、耐久性能、重金属浸出试验研究。结果表明:最佳粉磨参数为振动磨填充率40%,料球比1∶12;最佳粉磨细度700 m~2/kg;在此基础上,地聚合物基材最佳配比为矿粉70%,再生微粉20%,水玻璃旧砂微粉10%,其中激发剂的最佳配比(占基材总质量)为P·O52.5水泥15%,赤泥2.5%,脱硫石膏2.5%。铜、铅、镍、锌、镉重金属的浸出率都在0.2%以内。

组合羟肟酸下方解石和萤石中浮选氟碳铈矿的分离机理

苯甲羟肟酸(BHA)和辛基羟肟酸(OHA)以及二者组合羟肟酸(BHA+OHA)下,对氟碳铈矿、方解石、萤石三种矿物进行了浮选研究。通过红外光谱分析、总有机碳和紫外光谱吸附量测试和XPS分析研究了羟肟酸类在矿物表面的作用机理。结果表明:在pH=9.5、组合捕收剂(n(BHA)∶n(OHA)=2∶1)浓度为3×10^(-4) mol/L和盐化水玻璃3×10^(-3) mol/L条件下,氟碳铈矿、方解石和萤石的回收率分别为89.8%、18.5%和13.7%,人工混合矿REO品位由28.90%提升至55.41%,氟碳铈矿的回收率为80.41%,与方解石和萤石实现较好分离;组合捕收剂(BHA+OHA)在三种矿物表面发生共吸附,且组合捕收剂中每种药剂的吸附率大于相同浓度的单一药剂;盐化水玻璃阻碍捕收剂在方解石、萤石表面的吸附对捕收剂在氟碳铈矿表面吸附无影响,可以达到抑制方解石和萤石的目的,实现氟碳铈矿的选择性浮选。

西北大温差环境下温度对硫铝酸盐水泥砂浆抗压强度的影响

为研究西北大温差环境下温度对硫铝酸盐水泥砂浆作为浅层病害混凝土修补材料的抗压强度影响规律,设计了改性前后三个不同配合比、三个温度梯度(-25、25和80℃)和三个时间长度(6、12和24 h)的试验,测试了试样的抗压强度,采用扫描电子显微镜(SEM)和X射线衍射(XRD)的方法测试了试样的微观性能。结果表明,改性后的试样破坏模式均优于未改性试样。-25℃时,随着时间延长,改性后试样的抗压强度增大幅度均大于未改性试样;25℃时,三个配合比试样抗压强度变化规律相似,均轻微下降;80℃时,掺入0.3%(质量分数)水玻璃、0.1%(质量分数)聚丙烯纤维和0.4%(质量分数)膨胀剂试样的抗压强度下降幅度最小。同时,本文还建立了该配合比试样在不同温度下,随时间延长的相对抗压强度变化率计算公式,可为西北大温差环境下硫铝酸盐水泥砂浆作为浅层病害混凝土修补材料提供参考。

水玻璃固硫灰复合改善氯氧镁水泥强度特性研究

研究固硫灰和水玻璃对氯氧镁水泥强度的影响。研究表明,固硫灰的加入对水泥体强度起到促进作用,固硫灰掺量从0%升至5%,水泥体的抗压和抗折强度分别提升了21.4%和47.2%。水玻璃的添加量在2%以内对抗压和抗折起到一定的促进作用,但当掺量高于2%后,水泥体强度有明显下降,影响7 d和28 d强度因素的主次关系为固硫灰>水玻璃,而当水玻璃的掺量高过一定值后,其作用效果强于固硫灰。研究确定了一般墙体工程的强度设计要求,为研究水玻璃和固硫灰复合外加剂改性氯氧镁水泥在实际工程中的应用提供理论依据和数据支持。