Integrating water use systems and soil and water conservation measures into a hydrological model of an Iranian Wadi system

Water resources are precious in arid and semi-arid areas such as the Wadis of Iran. To sustainably manage these limited water resources, the residents of the Iranian Wadis have been traditionally using several water use systems(WUSs) which affect natural hydrological processes. In this study, WUSs and soil and water conservation measures(SWCMs) were integrated in a hydrological model of the Halilrood Basin in Iran. The Soil and Water Assessment Tool(SWAT) model was used to simulate the hydrological processes between 1993 and 2009 at daily time scale. To assess the importance of WUSs and SWCMs, we compared a model setup without WUSs and SWCMs(Default model) with a model setup with WUSs and SWCMs(WUS-SWCM model). When compared to the observed daily stream flow, the number of acceptable calibration runs as defined by the performance thresholds(Nash-Sutcliffe efficiency(NSE)≥0.68, –25%≤percent bias(PBIAS)≤25% and ratio of standard deviation(RSR)≤0.56) is 177 for the Default model and 1945 for the WUS-SWCM model. Also, the average Kling–Gupta efficiency(KGE) of acceptable calibration runs for the WUS-SWCM model is higher in both calibration and validation periods. When WUSs and SWCMs are implemented, surface runoff(between 30% and 99%) and water yield(between 0 and 18%) decreased in all sub-basins. Moreover, SWCMs lead to a higher contribution of groundwater flow to the channel and compensate for the extracted water by WUSs from the shallow aquifer. In summary, implementing WUSs and SWCMs in the SWAT model enhances model plausibility significantly.

Water Leakages in Public Water Supply System and How to Prevent Them

The article addresses the results of effective water losses prevention in public water supply systems, focusing on procedures for monitoring hidden leaks as the main part of losses and as the first step to control and prevent them. The described methodology has been applied based on a cross-border cooperation between twin capital cities Vienna and Bratislava in the Central Europe Region within the project deWaloP （Developing Water Loss Prevention） and adopted in Bratislava Water Company （BVS） in the Slovak Republic. The paper provides a complex of simple and easily available practices for analyses of water distribution measurements bringing essential information as to the necessity to use advanced procedures to actively reduce leakage. These practices involve minimum night flows analyses, hydrodynamic pressures analyses, pinpointing of water leakages by working with valves in the water network, the methodology of setting alarm limits for measured data, as well as use of advanced practices to obtain missing topologic data. As the water infrastructure in former socialistic countries are in bad technical condition and the lack of pertinent operational data is a significant obstacle to the application of a more sophisticated methodology based on GIS and other information systems, the procedures focus on using the most simple way to evaluate and control water losses. Finally, the introduction of described methodology in Bratislava Water Company after many years of unsuccessful effort even with expensive sophisticated leakage equipment brought positive outputs and the graph line of water losses level is finally going down. The use of expensive multi-correlating equipment together with human resources on the basis of implementing the above described leakage monitoring will subsequently become more effective, as it shall pinpoint major leakages, disclosure and removal of that shall significantly contribute to the effective reduction of water losses.

A modified soil water content measurement technique using actively heated fiber optic sensor

Soil water content measurement is critical in practical engineering.The actively heated fiber Bragg grating optic sensor(FBGS)has great potential of multi-point measurement for soil water content measurement in field.In this study,the effect of heating time on the measurement accuracy is discussed,and modifications are made for actively heated fiber optic(AHFO)sensors.The results demonstrate that if an integration data analysis method is used,the accuracy and reliability of soil water content measurement with AHFO sensors will be improved.Both a short fiber length and a short-term heating pattern are effective and can help to reduce soil disturbance.With the proposed integration method,a short heating time is guaranteed for measuring the soil water content.Such improvements will reduce the thermal disturbance to soil sample and improve the reliability of measurement.

Image-based Water Level Measurement Method under Stained Ruler

This paper propoes the water level measuring method based on the image, while the ruler used to indicate the water level is stained. The contamination of the ruler weakens or eliminates many features which are required for the image processing. However, the feature of the color difference between the ruler and the water surface are firmer on the environmental change compare to the other features. As the color differeaces are embossed, only the region of the ruler is limited to eliminate the noise, and the average image is produced by using several continuous frames. A histogram is then produced on the height axis of the produced intensity average image. Local peaks and local valleys are detected, and the section between the peak and valley which have the greatest change is looked for. The valley point at this very moment is used to detect the water level. The detected water level is then converted to the actual water level by using the mapping table. The proposed method is compared to the ultrasonic based method to evaluate its accuracy and efficiency on the various contaminated environments.

Water blocking effect caused by the use of hydraulic methods for permeability enhancement in coal seams and methods for its removal

To research techniques for removing the water blocking effect caused by hydraulic applications in coal seams,the use of surfactants is proposed,based on the mechanics of the water blocking effect.Centrifugal experiments were used to validate the effects of using surfactants;the results show that after dealing with vacuum saturation with water,the volume of micropores decreases,which results in a larger average pore size,and the volume of transitional pores,mesopores,macropores and total pores increases.Based on the distribution of pore size,the operation mode of ‘‘water infusion after gas extraction,then continuing gas extraction" is recommended to improve the volume of coal mine gas drainage.When the reflectance of vitrinite in coal samples is less than 1,using the surfactants Fast T,1631,APG,BS can mitigate the damage caused by the water blocking effect.But when the reflectance of vitrinite is larger than 1.4,the damage caused by the water blocking effect can be increased.When the surfactant CMC is used in hydraulic applications,the capillary forces of coal samples are almost negative,which means the capillary force is in the same direction as the gas extraction.The direction of capillary forces benefits the gas flow.So,using CMC can play an active role in removing the water blocking effect.Centrifugal experiments confirm that using CMC can effectively remove the water blocking effect,which has a beneficial effect on improving the gas drainage volume.

Measurement of water holdup in oil-in-water emulsions in wellbores using microwave resonance sensor

In this study,we propose a new method for water holdup measurement of oil-in-water emulsions with a microwave resonance sensor(MRS).The angle and length of the electrode plate are optimized by HFSS simulation software.Using a vector network analyzer(VNA),a static calibration experiment is conducted,and the resonant frequency distribution of oil-in-water emulsions is analyzed within an 80%–100%water holdup range.In addition,we observe and analyze the micron-sized oil bubble structure in the emulsifi ed state with an optical microscope.On this basis,a dynamic experiment of oil-in-water emulsions with high water cut and low velocity in a vertical upward pipe is conducted.S_(21) response curves of the MRS are obtained by the VNA under diff erent working conditions in real time.Finally,we analyze the relationship between the resonant frequency and water cut.Experimental results show that the MRS has an average resolution of 0.096%water cut for high water cut oil-in-water emulsions within the frequency range of 2.2–2.8 GHz.

Determination of gross α and β activities in Zouma River based on online HPGe gamma measurement system

This paper describes a low-cost and fast method to evaluate gross α and β^(-) radioactivities in natural water based on an online high-purity germanium detector gamma measurement system.The major gamma activities in natural water are provided by natural and artificial radionuclides such as ^(40) K,^(137)Cs,and radionuclides belonging to ^(238)U and ^(232)Th series.The main a emitters related to gamma emissions in natural water are ^(224)Ra(240.98 keV)and ^(226)Ra(186.21 keV),and the β^(-) emitters are ^(40) K(1460.85 keV),^(214)Bi(609.31 keV),^(208)Tl(583.19 keV),and ^(214)Pb(351.93 keV).The formula for gross α and β^(-) activity concentration is based on these radionuclides,and the short half-life decay products are considered in the calculation.The detection efficiency of the device across energy region(0–3 MeV)is obtained through Monte Carlo simulation,and a calibration experiment is conducted to verify the simulation results.Gamma radioactivity is measured continuously for 114 d in Pixian County and Dongfeng Canal located in the Zouma River,Chengdu,Sichuan Province,China.A comparison of the calculation results and monitoring data from the Sichuan Management and Monitoring Center Station of Radioactive Environment indicates that the percentage and absolute error of a activity concentration is lower than 53%and 0.02 Bq/L,respectively,and that of β-activity concentration is lower than 33.2%and 0.016 Bq/L,respectively.The method can rapidly determine gross α and β^(-) activity concentrations in natural water online.

Empowering Conditions for Good Water Governance-a Sustainable Model： Vilanculos Case Study （Mozambique）

This article shows the results of the project Empowering conditions for good water governance-a sustainable model： Vilanculos case study （Mozambique）, co-financed by the European Community. This project had the aim of improving sanitary conditions and increasing economic and financial sustainability of water services for the population of Vilanculos. The project has been developed and deployed with cooperation between Acque del Chiampo （an Italian water utility, near Vicenza）, the University of Brescia and the Vilanculos public water service utility, Empresa Mo^ambicana de Agua （EMA）. The paper reports analytical praxis for water distribution measurements, capable of providing essential data about the water network performances, to assess the eventual need for actions in order to solve possible and effective problems of the water service. These practices involve flow and pressure analyses, pinpointing of the network＇s criticalities and leakages by in-situ inspections along the network, managing the valves together with water service utility, as well as the use of a water distribution model to simulate the effects of the proposed interventions and specific software to automatically register bills and payments.

Impacts of water conservancy and soil conservation measures on annual runoff in the Chaohe River Basin during 1961-2005

Taking the Chaohe River Basin above the Miyun Reservoir in North China as a study area, the characteristics and variation trends of annual runoff and annual precipitation during 1961-2005 were analyzed applying Mann-Kendall test method on the basis of the hydrologic data of the major hydrological station （Xiahui Station） located at the outlet of the drainage basin and the meteorological data of 17 rainfall stations. Human activities including water conservancy projects construction and water diversion as well as implementation of soil and water conservation from 1961 to 2005 were carefully studied using time series contrasting method. The referenced period （1961-1980） that influenced slightly by human activities and the compared period （1981-2005） that influenced significantly by water conservancy and soil conservation measures were identified according to the runoff variation process analysis and abrupt change points detection during 1961-2005 applying double accumulative curve method, mean shift t-test method and Mann-Kendall mutation test technique. Based on the establishment of a rainfall-runoff empirical statistical model, impacts and the runoff-reducing effects of water conservancy and soil conservation measures on runoff reduction were evaluated quantitatively. The major results could be summarized as follows： （1） The annual precipitation in the drainage basin tends to decrease while the runoff has declined markedly since the 1960s, the average annual runoff from 1991 to 2000 was only 90.9% in proportion to that from 1961 to 1970. （2） The annual runoff variations in the drainage basin are significantly related to human activities. （3） During 1981-1990, 1991-2000, 2001-2005 and 1981-2005, the average annual runoff reduction amounts were 1.15×10^8, 0.28×10^8, 1.10×10^8 and 0.79×10^8 m^3 respectively and the average annual runoff-reducing effects were 31.99%, 7.13%, 40.71% and 23.79% accordingly. Runoff-reducing effects by water conservancy and soil conservation measures are more prominent in the low water period.

Determination of bulk viscosity of liquid water via pulse duration measurements in stimulated Brillouin scattering

We present a method by which to determine the bulk viscosity of water from pulse duration measurements of stimulated Brillouin scattering （SBS）. Beginning from a common model of Brillouin scattering, the bulk viscosity is shown to play an important role in Brillouin linewidth determination. Pulse durations of SBS back-reflected optical pulses are measured over the temperature range of 5-40℃. SBS linewidths are de- termined via Fourier transformation of the time-domain results, and the bulk viscosity of water is measured and derived from the obtained values. Our results show that the proposed method for measurement of pulse durations is an effective approach for determining bulk viscosity. The method can be easily extended to determine bulk viscosities of other Newtonian liquids.

Non-Contact Measurements of Water Jet Spreading Width with a Laser Instrument

Jet spreading width is one of the important characteristics of water jets discharging into the air.Many researchers have dealt with measuring this width,and contact measuring methods on the water jet surface were employed in a lot of the cases.In order to avoid undesirable effects caused by the contact on the jet surface,we introduce non-contact measuring methods with a laser instrument to the measurements of jet spreading width.In measurements,a transmitter emits sheet-like laser beam to a receiver.The water jet between the transmitter and the receiver interrupts the laser beam and makes a shadow.The minimum and maximum values of the shadow width are measured.In addition,pictures of the water jet are taken with a scale,and the shadow width is measured from the pictures.The experiments on various needle strokes were performed.Three kinds of width consistent with the jet structure were obtained.In the results,it can be concluded that our non-contact measuring methods are feasible.The data of jet spreading widths and jet taper were obtained and are useful for future applications.

Soil erosion assessment by RUSLE with improved P factor and its validation:Case study on mountainous and hilly areas of Hubei Province,China

The Revised Universal Soil Loss Equation(RUSLE)is widely used to estimate regional soil erosion.However,quantitative impacts of soil and water conservation(SWC)measures on conservation practice factor(P)of the RUSLE remain largely unclear,especially for the mountainous and hilly areas.In this study,we improved the RUSLE by considering quantitative impacts of different SWC measures on the P factor value.The improved RUSLE was validated against the long-term(2000-2015)soil erosion monitoring data obtained from 96 runoff plots(15—35°)in mountainous and hilly areas of Hubei Province,China;the result presented a high accuracy with the determination coefficient of 0.89.Based on the erosion monitoring data of 2018 and 2019,the Root Mean Square Error of the result by the improved RUSLE was 28.0%smaller than that by the original RUSLE with decrement of 19.6%—24.0%in the average P factor values,indicating that the soil erosion modelling accuracy was significantly enhanced by the improved RUSLE.Relatively low P factor values appeared for farmlands with tillage measures(P<0.53),grasslands with engineering measures(P<0.23),woodlands with biological measures(P<0.28),and other land use types with biological measures(P<0.51).The soil erosion modulus showed a downward trend with the corresponding values of 1681.21,1673.14,1594.70,1482.40 and 1437.50 t km^(-2)a-1 in 2000,2005,2010,2015 and 2019,respectively.The applicability of the improved RUSLE was verified by the measurements in typical mountainous and hilly areas of Hubei Province,China,and arrangements of SWC measures of this area were proposed.

Liquid Level Sensor Based on CMFTIR Effect in Polymer Optical Fiber

The macro-bending induced optical fiber cladding modes frustrated total internal reflection effect is used to realize the liquid level probe with a simple structure of single macro-bend polymer optical fiber loop. The test results show that the extinction ratio reaches 1.06dB. ＂First bath＂ phenomenon is not obvious （about 0.8%）. The robustness of the sensor is better, and the ability of anti-pollution is stronger compared with the conventional sensors. The process of making this sensing probe is extremely easy, and the cost is very low.