Adhesion forces for water/oil droplet and bubble on coking coal surfaces with different roughness

Surface roughness plays a significant role in floatability of coal.In the present paper,coking coal surface was polished by three different sandpapers and the surface properties were characterized by contact angle and roughness measurements.The effect of surface roughness on floatability was investigated by adhesion force measurement system for measuring interaction forces between droplets/bubbles and coking coal surfaces with different roughness.The results showed that the contact angle decreased with increasing roughness yet the adhesion force between the water droplet and coal surface increased owing to the increased contact line and the appearance of line pinning.Maximum adhesion forces between water and surfaces were 111.70,125.48,and 136.42μN when the roughness was 0.23,0.98,and 2.79 μm,respectively.In contrast,under a liquid environment,the adhesion forces between air bubble/oil droplet and coal surfaces were decreased with increasing roughness because of the restriction by water.Maximum adhesion forces of increasing roughness were 97.14,42.76,and 17.86 μN measured at interfaces between air bubble and coal surfaces and 169.48,145.84,and 121.02 lN between oil droplet and surfaces,respectively.Decreasing roughness could be beneficial to the spreading of oil droplets and the adhesion of bubbles which is conducive to flotation separation.

Purification of Produced Water from a Sour Oilfield in South Kuwait. 1. Oil-Water Separation and Industrial Salt Production

Produced water from an oil extraction site in South Kuwait was sampled after primary oil – water separation had been carried out. The produced water was filtered through a mixture of activated charcoal and esterified cellulosic material gained from spent coffee grounds as a tertiary adsorption treatment. The earth-alkaline metal ions and heavy metals were separated from the de-oiled produced water by addition of either sodium or potassium hydroxide in the presence of carbon dioxide or by direct addition of solid sodium carbonate. The resulting filtrate gave salt of industrial purity upon selective crystallization on evaporation.

Purification of Produced Water from a Sour Oilfield in South Kuwait. 2. Oil-Water Separation and Crystallization of Calcium Carbonate

Oil-water separation for produced water (PW) originating from an oil extraction site in South Kuwait was carried out using bleached, esterified cellulosic material from used coffee grounds. Thereafter, earth-alkaline metal ions, specifically calcium ions, of the de-oiled PW were removed by precipitation with sodium carbonate to give access to pure sodium chloride as industrial salt from the remaining PW. While the purity of the precipitated calcium carbonate (CaCO3) depends on the precipitation conditions, CaCO3 of up to 95.48% purity can be obtained, which makes it a salable product. The precipitation of CaCO3 decreases the amount of calcium ions in PW from 11,300 ppm to 84 ppm.

Variability in Quantity and Salinity of Produced Water from an Oil Production in South Kuwait

Produced water (PW) is the largest waste stream in the oil and gas industry. Water remains trapped for millions of years in the reservoir with oil and gas. When a hydrocarbon reservoir is infiltrated by a production well, the produced fluids commonly contain water. The understanding of this water’s constituents and volumes is vital for the sustainable continuity of production operations, as PW has a number of negative impacts on the infrastructure integrity of the operation. On the other hand, PW can be an alternative source of irrigation water as well as of industrial salt. Interestingly, both the quantity as well as the quality of PW do not remain constant but can vary, both progressively and erratically, even over short periods of time. This paper discusses such a situation of variable PW in an oil and gas operation in the State of Kuwait.

Kinetics of Bioremediation of Oil Contaminated Water Dispersed by Environment-Friendly Bacteria (Pseudomonas aeruginosa) and Fungi (Aspergillus niger)

The comparative effectiveness of remediating water polluted with crude oil, using environment-friendly bacteria (Pseudomonas aeruginosa) and fungi (Aspergillus niger) were investigated. The samples were separately treated with Aspergillus niger and Pseudomonas aeruginosa. The bioremediation kinetic efficiency for these systems was studied. At the end of the bioremediation periods, the oil and grease content of the samples decreased from 47.0 mg/L in the untreated sample to 7.0 mg/L after 20 days when inoculated with bacteria while the sample inoculated with fungi decreased to 10.0 mg/L. Post analysis when inoculated with bacteria showed a fall in the value of the biological oxygen demand (BOD) from 73.84 mg/L to 33.28 mg/L after 20 days, while, the fungi inoculated sample showed a reduction from 73.84 mg/L to 38.48 mg/L. The biodegradation process with the bacteria was consistent with the pseudo-first-order model with a rate constant of 0.0891 day-1, while the biodegradation process with the fungi was consistent with the first order reaction model with a rate constant of 0.422 day-1. The degree of degradation after the 20th day of inoculation with Pseudomonas aeruginosa was 85.11%, while with Aspergillus niger was 78.72%. Thus, the results obtained showed that, Pseudomonas aeruginosa performed better than Aspergillus niger. The bioremediation data with fungi fitted the first-order model, while that of the bacteria fitted the pseudo-first-order model. Therefore, the data obtained in this study could be applied in the design of a bioremediation system for potential application to remediation of crude oil polluted water.

Optimization of the Algorithm for Increasing Injection Rate in Water Injection Wells for Pressure Optimization in P Oilfield

In today’s society, with the continuous growth of energy demand, Bohai Oilfield, as an important offshore oil resource base in China, is facing increasingly severe challenges while contributing to national energy security. In order to improve the quality of water injection in the oilfield and gradually achieve efficient and stable production, Bohai Oilfield has launched a water injection well pressure optimization project, focusing on improving the efficiency and quality of water injection in the water injection wells, in order to achieve the optimal water injection plan. In practical work, P Oilfield continues to promote the development of water injection well pressure optimization projects, emphasizing practical exploration and continuous optimization of work plans. However, during the project implementation process, there were some problems, one of which was that the statistics of cumulative injection volume were not scientific enough, resulting in a more comprehensive and accurate presentation of the actual results of pressure optimization work. In the context of continuous improvement work, after careful analysis and research, P Oilfield has decided to optimize the cumulative injection rate algorithm to guide the oilfield’s water injection work in a more refined way, ensuring sufficient and good water injection, and enhancing the oilfield’s production efficiency and comprehensive competitiveness.

Solvent switching and purification of colloidal nano- particles through water/oil Interfaces within a density gradient

Traditional post-treatment of colloidal nanoparticles （NPs） usually involves repeated centrifugation-wash-sonication processes to separate NPs from the original synthetic environment; however, such separation processes have either high energy cost or low efficiency and tend to cause aggregation. Here we show a general and scalable colloid post-processing technique based on density gradient centrifugation through water/oil interfaces. Such a one-step technique can switch the solvent in a colloid at almost any concentration without aggregation, and meanwhile purify colloidal nanoparticles by separating them from by-products and environmental impurities. Droplet sedimentation was shown to be the mechanism of this one-step concentration/purification process, and mathematical modeling was established to quantify the accumulation and sedimentation velocities of different NPs.

Influences of water treatment agents on oil-water interfacial properties of oilfield produced water

The emulsion stability of oilfield produced water is related to the oil-water interfacial film strength and the zeta potential of the oil droplets. We investigated the effects of water treatment agents （corrosion inhibitor SL-2, scale inhibitor HEDP, germicide 1227, and flocculant polyaluminium chloride PAC） on the stability of oilfield produced water. The influence of these treatment agents on oil-water interfacial properties and the mechanism of these agents acting on the oilfield produced water were studied by measuring the interfacial shear viscosity, interfacial tension and zeta electric potential. The results indicated that the scale inhibitor HEDP could increase the oil-water interfacial film strength, and it could also increase the absolute value of the zeta potential of oil droplets. HEDP played an important role in the stability of the emulsion. Polyaluminum chloride （PAC） reduced the stability of the emulsion by considerably decreasing the absolute value of the zeta potential of oil droplets. Corrosion inhibitor SL-2 and germicide 1227 could decrease the oil-water interfacial tension, whereas they had little influence on oil-water interfacial shear viscosity and oil-water interfacial electricity properties.

Synthesis of a Novel Core-shell Type Acrylic-polyurethane Hybrid Emulsion Containing Siloxane and Fluorine as well as Water and the Oil Resistances of Cured Film

Siliconated polyurethane （Si-PU） was synthesized using isophorone diisocyanate （IPDI）, hydroxybutyl-terminated polydimethylsiloxane （PDMS）, polytetramethylene ether glycol （PTMG）, polypropylene glycol （PPG）, 1,6-hexanediol （HDO）, dimethylol propionic acid （DMPA） and triethylamine （TEA）. Based on butyl acrylate （BA）, 2, 2, 2-trifluoroethylmethacrylate （TFEMA） and Si-PU as a seed emulsion, a novel core-shell type acrylic-polyurethane hybrid emulsion, containing siloxane and fluorine （F-Si-PU）, was prepared by seeded emulsion polymerization. The contents of siloxane and fluorine were determined according to the feed ratio. Fourier transform infrared spectroscopy （FTIR） was used to identify the chain structures of Si-PU and F-Si-PU. Investigation of transmission electron microscopy （TEM） confirmed the core-shell structure of F-Si-PU emulsion. Measurement results of water contact angle and the swelling ratio in water and n-octane for cured film showed that the water and the oil resistances for F-Si-PU had been significantly improved at a suitable content of fluorine and siloxane.

Experimental investigation of the effects of various parameters on viscosity reduction of heavy crude by oil-water emulsion

The effects of water content, shear rate, temperature, and solid particle concentration on viscosity reduction （VR） caused by forming stable emulsions were investigated using Omani heavy crude oil. The viscosity of the crude oil was initially measured with respect to shear rates at different temperatures from 20 to 70℃. The crude oil exhibited a shear thinning behavior at all the temperatures. The strongest shear thinning was observed at 20℃. A non-ionic water soluble surfactant （Triton X-100） was used to form and stabilize crude oil emulsions. The emulsification process has significantly reduced the crude oil viscosity. The degree of VR was found to increase with an increase in water content and reach its maximum value at 50 % water content. The phase inversion from oil- oil emulsion occurred at 30 in-water emulsion to water-in- % water content. The results indicated that the VR was inversely proportional to temperature and concentration of silica nanoparticles. For water-in-oil emulsions, VR increased with shear rate and eventually reached a plateau at a shear rate of around 350 s^-1. This was attributed to the thinning behavior of the continuous phase. The VR of oil-in-water emulsions remained almost constant as the shear rate increased due to the Newtonian behavior of water, the continuous phase.

Components of Volatile Oil from Water-caltrop and Their Anti-tumor Effect in vitro

The volatile oil was extracted from water caltrop by steam distillation; it was then analyzed by GC-MS to obtain 16 components, 8 of which were identified. Apocynin was the most abundant one, accounting for 81.41% of the total oil. The in vitro inhibitory effects of the volatile oil on SMMC-7721, MCF-7, Hela, HL-60 cells, and human peripheral blood mononuclear cells（PBMC） were investigated via the MTT method. The morphological changes of the tumor cells were observed and the apoptosis of HL-60 cells was detected by flow cytometry. The proliferation of the tumor cells could be significantly inhibited and the apoptosis of HL-60 cells could be induced by the volatile oil. The proliferation inhibition effect of the volatile oil on HL-60 tumor cells and the induction of the apoptosis of ilL-60 cells had dose-dependent feature.

Produced Water from Oil and Gas Exploration—Problems, Solutions and Opportunities

Large volumes of water are generated in gas- and oil-production. This includes the water that is present originally in the reservoirs, but also water that is injected into the wells. While currently much of the produced water is either reinjected or disposed of after treatment, treated produced water is increasingly seen as an interesting resource, especially in water-scarce regions. This review looks at different PW treatment methods available, with an emphasis on the management of PW in oil- and gas production on the Arabian Peninsula.

Design and operation problems related to water curtain system forunderground water-sealed oil storage caverns

The underground water-sealed storage technique is critically important and generally accepted for the national energy strategy in China. Although several small underground water-sealed oil storage caverns have been built in China since the 1970s, there is still a lack of experience for large-volume underground storage in complicated geological conditions. The current design concept of water curtain system and the technical instruction for system operation have limitations in maintaining the stability of surrounding rock mass during the construction of the main storage caverns, as well as the long-term stability. Although several large-scale underground oil storage projects are under construction at present in China, the design concepts and construction methods, especially for the water curtain system, are mainly based on the ideal porosity medium flow theory and the experiences gained from the similar projects overseas. The storage projects currently constructed in China have the specific features such as huge scale, large depth, multiple-level arrangement, high seepage pressure, complicated geological conditions, and high in situ stresses, which are the challenging issues for the stability of the storage caverns. Based on years’ experiences obtained from the first large-scale （millions of cubic meters） underground water-sealed oil storage project in China, some design and operation problems related to water curtain system during project construction are discussed. The drawbacks and merits of the water curtain system are also presented. As an example, the conventional concept of “filling joints with water” is widely used in many cases, as a basic concept for the design of the water curtain system, but it is immature. In this paper, the advantages and disadvantages of the conventional concept are pointed out, with respect to the long-term stability as well as the safety of construction of storage caverns. Finally, new concepts and principles for design and construction of the underground water-sealed oil storage caverns are proposed.

Comparative Analysis of Produced Water Collected from Different Oil Gathering Centers in Kuwait

Kuwait is one of the major oil-producing countries, with an estimated oil production of around three million barrels/day. Increased oil production has resulted in the production of large amounts of produced water, which is a major problem for Kuwait Oil Company. Kuwait Oil Company generates large amounts of produced water daily and thus deserves special attention. A study of the characteristics of the produced water will determine how it can be treated and later used for irrigation or disposed without harming the environment. In this paper, samples of produced water from different oilfields in Kuwait were collected, and physiochemical analyses were carried out. The salt content, TDS and other physical characteristics of the Kuwait produced water samples were compared with those of other produced water samples from different oil-producing countries.

Water and Oil Resistance of Special Paperboard for Petroleum Packaging

The influence of different coating formulas and times on the water and oil resistance of paperboard was studied. The water and oil resistance of paperboard coated with a modified butadiene-styrene copolymer latex and fluorinated anion grease-proof agent was better than that coated with modified butadiene-styrene copolymer latex,where the modified butadiene-styrene copolymer latex was used as the pre-coating substrate and the F1516 fluorinated grease-proof agent was used as the top coating material. By coating modified butadiene-styrene copolymer latex with 30% solid content and F1516 fluorinated grease-proof agent with 24% solid content,the oil resistance of paperboard could reach anti-oil grade 12 and the water resistance could increased by98. 64%( compared with the base paperboard without any coating treatment).

Developing High Water-cut Oil Fields Deeply to Enhance Their Oil Recovery

In order to recognize the distribution of dispersed remaining oil,reservoirs should be described in more detail and quantitatively to establish refined and sophisticated 3D quantified reservoir model which can reflect the detailed variation in the reservoir and its structure.The key point of sophistication and quantification of reservoir characterization is to describe the geo-metry of interwell sandbodies and to estimate their reservoir parameters.

Nonlinear Behavior and Domain Feature at Oil/Water Interface

Studies on nonlinear behavior at oil/water interface membrane were performed. This system showed rhythmic oscillations and chaos of electrical potential in a given concentration domain. The nonlinear behavior response at the liquid membrane apparently resembled that of biological chemoreceptive membrane. The possibility of developing a new type of chemical sensor with the ability to simulate substance equilibrium in living organisms was suggested in the paper.

Three-Dimensional Imaging of Pore-Scale Water Flooding Phenomena in Water-Wet and Oil-Wet Porous Media

The penetration of water during water flooding has been observed over many years using several methods. A microfocused X-ray computed tomography scanner can be used to directly observe 3D water flooding in a nondestructive manner. To eliminate the possibility of false images being produced because of X-ray broadening effects, we developed a visualization method by arranging the brightness distribution of all phases involved. Water flooding experiments were conducted using oil-wet and water-wet porous media. The water phase was injected upward into packed glass beads containing an oil phase, and the process was scanned every minute until steady state was reached. Using this scheme, real-time, the water invasion pattern and oil trapping process in clusters of pores and individual pores can be observed clearly. By eliminating false images, the boundary of each phase could be identified with high precision, even in a single pore. Porelevel phenomena, including snap off (which has never before been captured in a real 3D porous medium), piston-like displacement, and the curvature of the interface, were also observed. Direct measurement of the pore throat radius and the contact angle between the wetting and nonwetting phases gave an approximation of the capillary pressure during the piston-like displacement and snap-off processes.

Prediction of wax precipitation region in wellbore during deep water oil well testing

During deep water oil well testing, the low temperature environment is easy to cause wax precipitation, which affects the normal operation of the test and increases operating costs and risks. Therefore, a numerical method for predicting the wax precipitation region in oil strings was proposed based on the temperature and pressure fields of deep water test string and the wax precipitation calculation model. And the factors affecting the wax precipitation region were analyzed. The results show that: the wax precipitation region decreases with the increase of production rate, and increases with the decrease of geothermal gradient, increase of water depth and drop of water-cut of produced fluid, and increases slightly with the increase of formation pressure. Due to the effect of temperature and pressure fields, wax precipitation region is large in test strings at the beginning of well production. Wax precipitation region gradually increases with the increase of shut-in time. These conclusions can guide wax prevention during the testing of deep water oil well, to ensure the success of the test.

The sensitivity of the array resistivity log to mud filtrate invasion and its primary five-parameter inversion for improved oil water recognition

In order to improve reservoir fluid recognition, the sensitivity of array resistivity response to the difference of the invasion properties in both oil-bearing layers and water layers is analyzed. Then the primary inversion is carried out based on the array resistivity log. The mud invasion process is numerically simulated based on the oil-water flow equation and water convection diffusion equation. The results show that the radial resistivity of a fresh mud-invaded oil-bearing layer presents complex distribution characteristics, such as nonlinear increase, increasing to decreasing and low resistivity annulus, and the resistive invasion profile of a water layer is monotonic. Under specific conditions, array resistivity log can reflect these changes and the array induction log is more sensitive. Nevertheless, due to the effect of factors like large invasion depth, reservoir physical and oil-bearing properties, the measured apparent resistivity may differ greatly from the actual mud filtrate invasion profile in an oil-bearing layer. We proposed a five-parameter formation model to simulate the complex resistivity distribution of fresh mud-invaded formation. Then, based on the principle of non-linear least squares, the measured array resistivity log is used for inversion with the Marquardt method. It is demonstrated that the inverted resistivity is typically non-monotonic in oil-bearing layers and is monotonic in water layers. Processing of some field data shows that this is helpful in achieving efficient reservoir fluid recognition.