Strength prediction model for water-bearing sandstone based on nearinfrared spectroscopy

The strength of water-bearing rock cannot be obtained in real time and by nondestructive experiments,which is an issue at cultural relics protection sites such as grotto temples.To solve this problem,we conducted a near-infrared spectrum acquisition experiment in the field and laboratory uniaxial compression strength tests on sandstone that had different water saturation levels.The correlations between the peak height and peak area of the nearinfrared absorption bands of the water-bearing sandstone and uniaxial compressive strength were analyzed.On this basis,a strength prediction model for water-bearing sandstone was established using the long short-term memory full convolutional network(LSTM-FCN)method.Subsequently,a field engineering test was carried out.The results showed that:(1)The sandstone samples had four distinct characteristic absorption peaks at 1400,1900,2200,and 2325 nm.The peak height and peak area of the absorption bands near 1400 nm and 1900 nm had a negative correlation with uniaxial compressive strength.The peak height and peak area of the absorption bands near 2200 nm and 2325 nm had nonlinear positive correlations with uniaxial compressive strength.(2)The LSTM-FCN method was used to establish a strength prediction model for water-bearing sandstone based on near-infrared spectroscopy,and the model achieved an accuracy of up to 97.52%.(3)The prediction model was used to realize non-destructive,quantitative,and real-time determination of uniaxial compressive strength;this represents a new method for the non-destructive testing of grotto rock mass at sites of cultural relics protection.

Prediction of subsurface settlement induced by shield tunnelling in sandy cobble stratum

This study focuses on the analytical prediction of subsurface settlement induced by shield tunnelling in sandy cobble stratum considering the volumetric deformation modes of the soil above the tunnel crown.A series of numerical analyses is performed to examine the effects of cover depth ratio(C/D),tunnel volume loss rate(h t)and volumetric block proportion(VBP)on the characteristics of subsurface settle-ment trough and soil volume loss.Considering the ground loss variation with depth,three modes are deduced from the volumetric deformation responses of the soil above the tunnel crown.Then,analytical solutions to predict subsurface settlement for each mode are presented using stochastic medium theory.The influences of C/D,h t and VBP on the key parameters(i.e.B and N)in the analytical expressions are discussed to determine the fitting formulae of B and N.Finally,the proposed analytical solutions are validated by the comparisons with the results of model test and numerical simulation.Results show that the fitting formulae provide a convenient and reliable way to evaluate the key parameters.Besides,the analytical solutions are reasonable and available in predicting the subsurface settlement induced by shield tunnelling in sandy cobble stratum.

Physical and numerical investigations of target stratum selection for ground hydraulic fracturing of multiple hard roofs

Ground hydraulic fracturing plays a crucial role in controlling the far-field hard roof,making it imperative to identify the most suitable target stratum for effective control.Physical experiments are conducted based on engineering properties to simulate the gradual collapse of the roof during longwall top coal caving(LTCC).A numerical model is established using the material point method(MPM)and the strain-softening damage constitutive model according to the structure of the physical model.Numerical simulations are conducted to analyze the LTCC process under different hard roofs for ground hydraulic fracturing.The results show that ground hydraulic fracturing releases the energy and stress of the target stratum,resulting in a substantial lag in the fracturing of the overburden before collapse occurs in the hydraulic fracturing stratum.Ground hydraulic fracturing of a low hard roof reduces the lag effect of hydraulic fractures,dissipates the energy consumed by the fracture of the hard roof,and reduces the abutment stress.Therefore,it is advisable to prioritize the selection of the lower hard roof as the target stratum.

Deformation Mechanism and Design Countermeasures of Tunnel Portal in Volcanic Deposit Clay Stratum

Shortly after tunneling,problems such as primary-support through cracks and clearance infringement are found in the shallow-buried section of tunnel No.4 of the Jakarta-Bandung High Speed Railway(Jakarta-Bandung HSR),and orthogonal cracks can be found on the earth surface in front of the working face,which brings great challenges to the tunnel construction.In view of the above engineering problems,the sliding surface is speculated according to the geological and field conditions,and the impact of landslides is applied in the model in the form of external load.The paper uses the numerical simulation method to analyze and compare the impact of landslides on the tunnel structure and deformation,and puts forward the reinforcement measures.The conclusions of the studies are:(1)under the influence of heavy rainfall,the strength index of volcanic deposit clay stratum drops sharply,and meanwhile the multiple factors including tunnel excavation are liable to cause sliding of the front slope;(2)parallel landslide in front of the tunnel has a great impact on the tunnel,so setting-up of pre-reinforcement measures to control landslide shall be the focus of similar projects during design;(3)the deformation and stress of the tunnel structure can be significantly controlled for safe construction by strengthening the shallow-buried tunnel with pile foundation and longitudinal and transverse beam frames during landslide.

The Water-Bearing Numerical Model and Its Operational Forecasting Experiments PartII: The Operational Forecasting Experiments

おhe water-bearing numerical model is undergone all round examinations during the operational forecasting experiments from 1994 to 1996. A lot of difficult problems arising from the model′s water-bearing are successfully resolved in these experiments through developing and using a series of technical measures. The operational forecasting running of the water-bearing numerical model is realized stably and reliably, and satisfactory forecasts are obtained.

Prediction Technology of Buried Water-Bearing Structures in Coal Mines Using Transient Electromagnetic Method

Buried water-conducting and water-bearing structures in front of the driving head may easily lead to water bursts in coal mines. Therefore,it is very important for the safety of production to make an accurate and timely forecast about water bursts. Based on the smoke ring effect of transient electromagnetic fields,the principle of transient electro-magnetic method used in detecting buried water-bearing structures in coal mines in advance,is discussed. Small multi-turn loop configurations used in coal mines are proposed and a field procedure of semicircular sector scanning is presented. The application of this method in one coal mine indicates that the technology has many advantages compared with others. The method is inexpensive,highly accurate and efficient. Suggestions are presented for future solutions to some remaining problems.

The Water-Bearing Numerical Model and Its Operational Forecasting Experiments Part I: The Water-Bearing Numerical Model

In first paper of articles, the physical and calculating schemes of the water-bearing numerical model are described. The model is developed by bearing all species of hydrometeors in a conventional numerical model in which the dynamic framework of hydrostatic equilibrium is taken. The main contributions are: the mixing ratios of all species of hydrometeors are added as the prognostic variables of model, the prognostic equations of these hydrometeors are introduced, the cloud physical framework is specially designed, some technical measures are used to resolve a series of physical, mathematical and computational problems arising from water-bearing; and so on. The various problems (in such aspects as the designs of physical and calculating schemes and the composition of computational programme) which are exposed in feasibility test, in sensibility test, and especially in operational forecasting experiments are successfully resolved using a lot of technical measures having been developed from researches and tests. Finally, the operational forecasting running of the water-bearing numerical model and its forecasting system is realized stably and reliably, and the fine forecasts are obtained. All of these mentioned above will be described in second paper.

Vertical variation of trace elements and its relation to the water-bearing capacity of Ordovician strata,in Datun coal field

We tested for fourteen trace elements in samples collected from the Ordovician strata in Datun coal field. The vertical concentration variation of these trace dements is reported. The relationship of the variation to the water-bearing capacity of the Ordovician strata is discussed. The minimum concentration of eleven （of 14 total） trace elements appears in the lower Majiagou formation. The maximum concentrations mainly appear in the Badou and Jiawang formations： eight maxima are located in Badou and four more are in Jiawang. The study of karst development and the water-bearing capacity of Ordovician strata shows that karst is well developed in the Majiagou formation and there is a consequent high water-bearing capacity in this formation： Badou and Jiawang formations are contrary to this situation. The results illustrate that the minimum concentrations of most trace elements within certain Ordovician formations can be taken as strong evidence for the existence of a well developed karst and a high water-bearing capacity.

A method for predicting the water-flowing fractured zone height based on an improved key stratum theory

In the process of using the original key stratum theory to predict the height of a water-flowing fractured zone(WFZ),the influence of rock strata outside the calculation range on the rock strata within the calculation range as well as the fact that the shape of the overburden deformation area will change with the excavation length are ignored.In this paper,an improved key stratum theory(IKS theory)was proposed by fixing these two shortcomings.Then,a WFZ height prediction method based on IKS theory was established and applied.First,the range of overburden involved in the analysis was determined according to the tensile stress distribution range above the goaf.Second,the key stratum in the overburden involved in the analysis was identified through IKS theory.Finally,the tendency of the WFZ to develop upward was determined by judging whether or not the identified key stratum will break.The proposed method was applied and verified in a mining case study,and the reasons for the differences in the development patterns between the WFZs in coalfields in Northwest and East China were also fully explained by this method.

Resistivity tomography study on samples with water-bearing structure

The apparent resistivity of the samples with water-bearing configuration was measured by an electrode-array and 2-D resistivity images of these samples were reconstructed then. The obtained series of tomograms reveal the dis tribution and its variation of true resistivity within the samples caused by the changes of crack and liquid distribu tion. Applying this method to the simulation experiment on the electrical properties of rocks, the fracturing and water filling process, which produces the electrical changes, can be brought to light clearly.

Correction to:Wear mechanism and life prediction of the ripper in a 9‐m‐diameter shield machine tunneling project of the Beijing new airport line in a sand‐pebble stratum

Jiang H,Zhu J,Zhang X,Zhang J,Li H,Meng L.Wear mechanism and life prediction of the ripper in a 9‐m‐diameter shield machine tunneling project of the Beijing new airport line in a sand‐pebble stratum.Deep Undergr Sci Eng.2022;1:65‐76.doi:10.1002/dug2.12010.

Study on the disaster caused by the linkage failure of the residual coal pillar and rock stratum during multiple coal seam mining:mechanism of progressive and dynamic failure

Multi-seam mining often leads to the retention of a significant number of coal pillars for purposes such as protection,safety,or water isolation.However,stress concentration beneath these residual coal pillars can significantly impact their strength and stability when mining below them,potentially leading to hydraulic support failure,surface subsidence,and rock bursting.To address this issue,the linkage between the failure and instability of residual coal pillars and rock strata during multi-seam mining is examined in this study.Key controls include residual pillar spalling,safety factor(f.),local mine stiffness(LMS),and the post-peak stiffness(k)of the residual coal pillar.Limits separating the two forms of failure,progressive versus dynamic,are defined.Progressive failure results at lower stresses when the coal pillar transitions from indefinitely stable(f,>1.5)to failing(f,<1.5)when the coal pillar can no longer remain stable for an extended duration,whereas sud-den(unstable)failure results when the strength of the pillar is further degraded and fails.The transition in mode of failure is defined by the LMS/k ratio.Failure transitions from quiescent to dynamic as LMS/k.<1,which can cause chain pillar instability propagating throughout the mine.This study provides theoretical guidance to define this limit to instability of residual coal pillars for multi-seam mining in similar mines.

中国石化超深层钻完井关键技术挑战及展望

超深层是中国石化油气勘探开发的重要增储上产领域。针对超深层勘探开发需求和高温高压及复杂地质环境带来的工程挑战,中国石化持续开展关键技术攻关,在钻完井基础理论和方法、钻完井装备、高温井筒工作液、耐高温井下工具仪器和完井测试等方面取得关键技术进展,保障了120口超8 000 m油气井的安全钻探,钻深能力突破9 000 m,助推塔里木盆地顺北大型超深油气田建设、四川盆地海相特深层油气勘探开发突破,为保障超深层油气勘探开发提供了有力的工程技术支撑。随着油气勘探开发不断向更深层推进,技术升级转型需求日益迫切,需进一步夯实理论研究基础,突破耐高温关键工具仪器和井筒工作液,加快推进钻完井工程技术向数智化转型,为保障深层、超深层油气高效勘探开发和加快技术升级转型提供工程技术支撑。

软土地层临近地铁基坑施工影响控制研究

随着城市地铁沿线地下空间的持续开发,基坑施工对临近地铁变形影响控制越来越受到关注。以上海某邻近地铁的基坑工程为例,通过实测分析和数值计算的方法研究了基坑开挖和拆撑对临近隧道变形的影响,并对伺服系统控制临近隧道变形进行定量分析。结果表明:覆存于软土地层中的隧道对临近施工扰动非常敏感,尽管大区基坑与隧道间距超过2.5倍开挖深度,隧道变形仍超过了监护要求的控制值;大区地下结构施工时拆撑对隧道收敛变形影响超过开挖影响的50%;应力伺服支撑系统对控制临近隧道变形比较有效,适当的“负位移”可以对隧道变形产生有利效果。

砂卵石地层矿山法隧道长管棚支护机理及应用

研究目的:砂卵石地层由于卵石强度高且颗粒分布无序,因此长管棚施工地层扰动大且支护效果难以保证,已成为制约隧道实际应用的一大瓶颈。本文以某轨道交通暗挖法车站为依托工程,采用理论分析、现场测试与数值模拟相结合的方法,对不同直径、不同环向间距条件下长管棚的支护效果进行了深入研究,以期揭示砂卵石地层矿山法隧道长管棚支护机理,提出最佳支护参数。研究结论:(1)砂卵石地层,暗挖隧道管棚超前支护条件下,地层沉降变形在向地表传递过程中,沿高度方向的折减率约为0.91 mm/m;(2)管棚超前支护效果对矿山法隧道工程安全具有决定性作用,须采取措施减小管棚施工扰动及相应地层变形;(3)根据单因素敏感性分析结果,地表沉降随管棚支护长度的增加而增大,随管棚环向间距的增大而增加,且基本呈正相关;(4)为有效控制地表沉降并提高工程经济效益,建议直径127 mm管棚环向间距宜为35 cm,支护长度宜为40 m;直径159 mm管棚建议环向间距宜为40 cm,支护长度宜为40 m;直径209 mm管棚建议环向间距宜为45 cm,支护长度宜为50 m;管棚直径与其最佳打设长度正相关;(5)本研究结论可为砂卵石地层矿山法隧道支护措施提供借鉴与参考。

成都平原浅层天然气高瓦斯隧道抽排性能评价

针对浅层天然气工区高瓦斯隧道盾构施工难的问题,借助工程实例,采用理论分析、数值模拟和现场试验的方法,分析了成都平原浅层天然气抽排性能的影响因素,确定了研究区的有效抽排半径和抽排时间。结果表明,当裂隙渗透率为39 mD、瓦斯压力为0.31 MPa时,研究区浅层天然气高瓦斯工区的有效抽排半径为5 m、抽排时间为60 min,与煤层瓦斯的抽排参数差异巨大;抽排负压对抽排流量影响较大,对有效抽排半径影响较小;抽排流量和有效抽排半径与地层初始渗透率的变化呈现正相关关系。

软土地层双洞口顶管接收井下沉力学特性研究

相较于常规沉井,顶管接收井几何形式的差异对结构受力、变形的影响规律尚不明确,亟待对此展开深入研究。以武汉市某排水顶管工程矩形接收井为依托,对沉井结构受力及下沉姿态开展现场监测,并利用数值模拟进行了对比验证和拓展研究。结果表明:预设顶管接收洞口引起的结构局部刚度降低,会导致结构在初沉阶段受弯效应增强,从而使接收洞口附近的内层钢筋压应力减小并使钢筋转向受拉状态,并且在下沉后期加剧该处钢筋应力变化幅度;因沉井外壁摩阻力增大而产生的附加应力叠加弯矩作用,使结构内、外层纵向钢筋沿井壁厚度方向的内力分布不均。对软土地层进行土体加固,有利于提高顶管接收井结构稳定性和顶管机头接收精度。

地热井砂岩热储回灌堵塞机理及解堵研究

地热井回灌是制约水热型地热持续开发的“卡脖子”难题,特别是砂岩热储的回灌更为艰难。为揭示制约砂岩热储回灌过程中面临的堵塞难题,以陕西关中渭河盆地某“一采一灌”模式砂岩地热井为例开展试验研究,探究砂岩热储回灌过程中的4类堵塞机理,并提出相应解堵措施。结果表明:碳酸盐类、部分铝硅酸盐类和铁类矿物沉淀受温度影响较大,地层温度的升高会加速其化学堵塞的形成;随温度的上升,悬浮物堵塞和化学堵塞会构成协同效应。同时悬浮物颗粒布朗运动速度也因温度上升而增大,使堵塞更严重;回灌产生气体堵塞的原因主要是:大体积气泡进入储层内部难、气泡直径与底层喉道大小相当;腐生菌和铁细菌是成微生物堵塞的主要微生物。通过加入阻垢剂可有效防止化学堵塞,采取多级过滤可减缓物理堵塞,在回灌系统中加入自动排气装置可防止气体堵塞,对尾水进行灭菌处理降低微生物堵塞风险。经过现场回暖季试验,采取的解堵措施应用于目标地热井后的回灌率达100%,降低了回灌过程中可能发生的堵塞对回灌带来的不良影响。

基于EDEM的砂卵石地层盾构刀具磨损特征研究

为揭示砂卵石地层土压平衡盾构典型刀具的磨损特征,指导该地层中盾构刀具的设计、布置等关键问题。采用室内三轴试验及数值离散元软件(EDEM)仿真分析,标定了颗粒-刀具磨损接触参数。依托北京新机场“磁各庄-1号风井”砂卵石盾构工程,构建了砂卵石地层EDEM数值盾构模型,可视化了砂卵石地层土压平衡盾构中典型刀具(楔犁刀、刮刀)的磨损特征,通过实际工程对模型进行了验证。研究表明:(1)以犁松原状砂卵石土为目的的楔犁刀具是掘进主切削刀具,表现为刀头合金表面以及刃角处连续的摩擦磨损形式,磨损量较大;(2)以剥落输排为目的刮刀主要表现为刀身迎土面以及刀头合金表面随机的点蚀磨损,磨损量较小;(3)刀盘径向刀具的磨损量随轨迹半径及刀体高度的增加而增大,同轨迹上高刀的磨损系数高于低刀,高刀对低刀的磨损有保护作用;刀盘径向刀具和环向刀具的“梯次化”布置可延长盾构单次连续掘进距离。

成都地区卵石地层深基坑开挖的土压力计算方法

[目的]现有土压力理论计算方法未考虑卵石地层孔隙度大、结构松散等离散性特点,计算结果与实际土压力有所偏差,需要研究适用于成都地区卵石地层的土压力计算方法。[方法]以成都轨道交通7号线为依托,分析卵石地层深基坑土压力与朗肯土压力理论值的差别,并建立深基坑开挖土压力计算方法。采用离散元数值模拟和数据统计分析,获取围护结构平动、围护结构绕墙顶转动和围护结构绕墙底转动三种基本变位模式下静止土压力、被动土压力和主动土压力的分布特征。与朗肯土压力理论计算结果进行比较,得到不同变位模式下三种土压力的修正系数,并建立深基坑土压力修正计算方法。进一步与现场实测数据比较,对比验证所提出的土压力计算方法。[结果及结论]主动土压力和被动土压力分布形式具有强烈的非线性,可采用双折线进行描述,交点分别位于埋深8 m和9 m处。静止土压力修正系数分布在0.91~0.96之间,在使用时不需要修正;主动土压力修正系数分布在0.33~0.78之间,被动土压力修正系数分布在0.52~0.91之间,在使用时应予以修正。所提出的卵石地层深基坑土压力计算结果与现场实测结果吻合较好,可为类似轨道交通工程提供参考。