Wind-Vortex-Induced Vibrations of a Deepwater Jacket Pipe and Vibration Suppression Using a Nonlinear Energy Sink

The purpose of this study is to investigate the suppression effect of a nonlinear energy sink(NES)on the wind-vortex-induced pipe vibration and explore the influence of damping,stiffness,and NES installation position on the suppression effect.In this work,the wind-vortex-induced vibration of an elastic pipe of a deepwater jacket was studied,and vibrations were suppressed by using an NES.A van der Pol wake oscillator was used to simulate vortex-induced force,and the dynamic equation of the pipe considering the NES was established.The Galerkin method was applied to discretize the motion equation,and the vortex-induced vibration(VIV)of the pipe at reduced wind speeds was numerically analyzed.The novelty of this research is that particle swarm optimization was used to optimize the parameters of the NES to improve vibration suppression.The influence of the installation position,nonlinear stiffness,and damping parameters of the NES on vibration suppression was analyzed.Results showed that the optimized parameter combinations of the NES can effectively reduce wind-vortex-induced pipe vibration.The installation position of the NES had a significant effect on vibration suppression,and the midpoint of the pipe was the optimal NES installation position.An increase in stiffness or a 10% decrease in damping may cause vibration suppression failure.The results of this study provide some guidance for VIV suppression in deepwater jacket pipes.

Lateral ring compression test applied to a small caliber steel jacket:Identification of a constitutive model

The evolution of threats and scenarios requires continuous performance improvements of ballistic protections for armed forces.From a modeling point of view,it is necessary to use sufficiently precise material behavior models to accurately describe the phenomena observed during the impact of a projectile on a protective equipment.In this context,the goal of this paper is to characterize the behavior of a small caliber steel jacket by combining experimental and numerical approaches.The experimental method is based on the lateral compression of ring specimens directly machined from the thin and small ammunition.Various speeds and temperatures are considered in a quasi-static regime in order to reveal the strain rate and temperature dependencies of the tested material.The Finite Element Updating Method(FEMU)is used.Experimental results are coupled with an inverse optimization method and a finite element numerical model in order to determine the parameters of a constitutive model representative of the jacket material.Predictions of the present model are verified against experimental results and a parametric study as well as a discussion on the identified material parameters are proposed.The results indicate that the strain hardening parameter can be neglected and the behavior of the thin steel jacket can be described by a modeling without strain hardening sensitivity.

The next GORE-TEX for jackets?

Columbia is a world-renowned manufacturer of outdoor products.Its product range covers all aspects of outdoor equipment such as jackets,down jackets,outdoor footwear,backpacks and accessories.In the outdoor industry,Columbia was the first brand to propose a three-in-one garment design concept.This practical design has since been adopted by almost every outdoor brand.The Columbia Jacket is positioned for urban outdoor recreation.Its rugged materials and design make it suitable for low-altitude outdoor sports as well as urban commuting.

Upgrading jackets for spring

When the gentle breeze of spring starts to fill the air,it's often a time of transition,where the chill of winter gives way to the warmth of the coming season.However,for those who love the outdoors,spring can still present its own set of challenges,especially when it's time to choose the right jacket.Whether you're hiking in the hills,exploring the trails,or just taking a leisurely walk in the park,having a jacket that offers the perfect blend of warmth,comfort,and breathability is crucial.We'll delve into the various options available for jackets that are perfect for the outdoors in spring.

Why own an Arc’teryx jacket?

Arc’teryx’s Beta AR Jacket sets a new bar in terms of what a mainstream outdoor jacket can do.You’ll turn around and charge headfirst into a rainstorm with this fully impermeable outer layer that packs in everything you need to lock in your core and stay dry.Unlike some jackets,the best part is that this jacket also pays dividends in sunny weather.While it’s designed for nasty weather,it stays comfortable when the storm passes away.The company’s high-tech waterproof membrane simultaneously wicks moisture and finally kicks that classic clammy raincoat feeling to the curb.

Design of Balanced Reactor Welded with Water-Cooled Aluminum Busbars

A new process of welding aluminum water-cooled busbars is proposed, It can not only reduce the weight and cost, but also improve the dynamic and thermal stability. Furthermore~ both finite element method analysis and a prototype test testify the advantages of the design which is not limited by load current and provides a new approach for water-cooled reactors.

Analysis and optimization of heat loss for water-cooled furnace roller

A heat transfer model of furnace roller cooling process was established based on analysis of furnace roller＇s structure. The complicated model was solved with iteration planning algorithm based on Newton search. The model is proved logical and credible by comparing calculated results and measured data. Then, the relationship between water flow velocity, inlet water temperature, furnace temperature and roller cross section temperature, outlet water temperature, water temperature rise, cooling water heat absorption was studied. The conclusions and recommendations are mainly as follows： l） Cooling water temperature rise decreases with the increase of water flow velocity, but it has small relationship with inlet water temperature; 2） In order to get little water scale, inlet water temperature should be controlled below 30 ℃. 3） The cooling water flow velocity should be greater than critical velocity. The critical velocity is 0.07 m/s and water flow velocity should be controlled within 0.4-0.8 m/s. Within this velocity range, water cooling efficiency is high and water temperature rise is little. If cooling water velocity increases again, heat loss will increase, leading to energy wasting.

Numerical Simulation on Subcooled Boiling Heat Transfer Characteristics of Water-Cooled W/Cu Divertors

In order to realize safe and stable operation of a water-cooled W/Cu divertor under high heating condition,the exact knowledge of its subcooled boiling heat transfer characteristics under different design parameters is crucial.In this paper,subcooled boiling heat transfer in a water-cooled W/Cu divertor was numerically investigated based on computational fluid dynamic（CFD）.The boiling heat transfer was simulated based on the Euler homogeneous phase model,and local differences of liquid physical properties were considered under one-sided high heating conditions.The calculated wall temperature was in good agreement with experimental results,with the maximum error of 5%only.On this basis,the void fraction distribution,flow field and heat transfer coefficient（HTC）distribution were obtained.The effects of heat flux,inlet velocity and inlet temperature on temperature distribution and pressure drop of a water-cooled W/Cu divertor were also investigated.These results provide a valuable reference for the thermal-hydraulic design of a water-cooled W/Cu divertor.

Preparation of Al-Zn-Mg-Cu alloy semisolid slurry through a water-cooled serpentine pouring channel

The semisolid slurry of Al-Zn-Mg-Cu alloy was prepared through a self-designed water-cooled copper serpentine pouring channel(WSPC) machine. Influences of pouring temperature, the number of turns and the cooling water flow rate on the microstructure of the semisolid Al-Zn-Mg-Cu alloy slurry were investigated. The results show that the semisolid Al-Zn-Mg-Cu alloy slurry with satisfactory quality can be generated by the WSPC when the pouring temperature is in the range between 680 ℃ and 700 ℃. At a given pouring temperature, the average grain size of primary α-Al decreases and the shape factor increases with the increase of the number of turns. When the cooling water flow rate is 450 L·h^(-1), the obtained semisolid slurry is optimal. During the preparation of the semisolid Al-Zn-Mg-Cu alloy slurry with low superheat pouring, the alloy melt has mixed inhibition and convection flow characteristics by "self-stirring". When the alloy melt flows through the serpentine channel, the chilling effect of the inner wall of the channel, the convection and mixed inhibition of the alloy melt greatly promote the heterogeneous nucleation and grain segregation. This effect destroys the dendrite growth mode under traditional solidification conditions, and the primary nuclei gradually evolve into spherical or nearspherical grains.

Optimization of the Water-Cooled Structure for the Divertor Plates in EAST Based on an Orthogonal Theory

An orthogoual experimental scheme was designed for optimizing a water-cooled structure of the divertor plate. There were three influencing factors： the radius R of the water- cooled pipe, and the pipe spacing L1 and L3. The influence rule of different factors on the cooling effect and thermal stress of the plate were studied, for which the influence rank was respectively R 〉 L1 〉 L3 and L3 〉 R 〉 L1. The highest temperature value decreased when R and L1 increased~ and the maximum thermal stress value dropped when R, L1 and L3 increased. The final optimized results can be summarized as： R equals 6 mm or 7 mm, L1 equals 19 mm, and L3 equals 20 mm. Compared with the initial design, the highest temperature value had a small decline~ and the maximum thermal stress value dropped by 19~ to 24~. So it was not ideal to improve the cooling effect by optimizing the geometry sizes of the water-cooled structure, even worse than increasing the flow speed, but it was very effective for dropping the maximum thermal stress value. The orthogoaal experimental method reduces the number of experiments by 80%, and thus it is feasible and effective to optimize the water-cooled structure of the divertor plate with the orthogonal theory.

Hydrodynamic Characteristics of Three-Bucket Jacket Foundation for Offshore Wind Turbines During the Lowering Process

The three-bucket jacket foundation is a new type of foundation for offshore wind turbine that has the advantages of fast construction speed and suitability for deep water. The study of the hoisting and launching process is of great significance to ensure construction safety in actual projects. In this paper, a new launching technology is proposed that is based on the foundation of the three-bucket jacket for offshore wind turbine. A complete time domain simulation of the launching process of three-bucket jacket foundation is carried out by a theoretical analysis combined with hydrodynamic software Moses. At the same time, the effects of different initial air storage and sea conditions on the motion response of the structure and the hoisting cable tension are studied. The results show that the motion response of the structure is the highest when it is lowered to 1.5 times the bucket height. The natural period of each degree of freedom of the structure increases with the increase of the lowering depth. The structural motion response and the hoisting cable tension vary greatly in the early phases of Stages Ⅰ and Ⅲ, smaller in Stage Ⅱ, and gradually stabilize in the middle and late phases of Stage Ⅲ.

Analysis of surface cracking in water-cooled rolls and heat transfer between furnace chamber and rolls in a direct flame furnace

In the direct fired furnace of a continuous annealing line, seal rolls are susceptible to deformation that leads to surface defects of steel strips. According to failure analysis, the reasons include improper structural design and heat imbalance. An improved design has been proposed to reduce stress concentration and thermal radiation. A heat transfer model has been employed to determine the proper water flow rate for roll cooling. Industrial application proves that seal rolls with the new design has less deformation and longer service life.

Fully Immersing Water-Cooled Radial Slab Laser and its Incoherent Beam Combination

A novel scheme of fully immersing water cooling is proposed for a Nd：glass radial slab laser. The slab medium is entirely immersed in the circulating water Ailing the pumping cavity, which enables much lower temperature and reasonably smaller thermal gradient in the slab medium. The radial slab is symmetrically and synchronously pumped by eight flash lamps, and produces multi-output beams with a total energy of 469md. Incoherent beam combination property of the multi-output beams is also investigated. The approach suggested here provides a way of scaling the slab lasers to much higher output levels and also a convenience for beam combinations.

The Corrected Simulation Method of Critical Heat Flux Prediction for Water-Cooled Divertor Based on Euler Homogeneous Model

An accurate critical heat flux（CHF） prediction method is the key factor for realizing the steady-state operation of a water-cooled divertor that works under one-sided high heating flux conditions.An improved CHF prediction method based on Euler＇s homogeneous model for flow boiling combined with realizable k-ε model for single-phase flow is adopted in this paper in which time relaxation coefficients are corrected by the Hertz-Knudsen formula in order to improve the calculation accuracy of vapor-liquid conversion efficiency under high heating flux conditions.Moreover,local large differences of liquid physical properties due to the extreme nonuniform heating flux on cooling wall along the circumference direction are revised by formula IAPWSIF97.Therefore,this method can improve the calculation accuracy of heat and mass transfer between liquid phase and vapor phase in a CHF prediction simulation of water-cooled divertors under the one-sided high heating condition.An experimental example is simulated based on the improved and the uncorrected methods.The simulation results,such as temperature,void fraction and heat transfer coefficient,are analyzed to achieve the CHF prediction.The results show that the maximum error of CHF based on the improved method is 23.7%,while that of CHF based on uncorrected method is up to 188%,as compared with the experiment results of Ref.[12].Finally,this method is verified by comparison with the experimental data obtained by International Thermonuclear Experimental Reactor（ITER）,with a maximum error of 6% only.This method provides an efficient tool for the CHF prediction of water-cooled divertors.

Modal Parameter Identification Method of Jacket Platform Structure Based on AFDD and Optimized FBFFT

Offshore platforms are susceptible to structural damage due to prolonged exposure to random loads,such as wind,waves,and currents.This is particularly true for platforms that have been in service for an extended period.Identifying the modal parameters of offshore platforms is crucial for damage diagno sis,as it serves as a prerequisite and foundation for the process.Therefore,it holds great significance to prioritize the identification of these parameters.Aiming at the shortcomings of the traditional Fast Bayesian Fast Fourier Transform(FBFFT) method,this paper proposes a modal parameter identification method based on Automatic Frequency Domain Decomposition(AFDD) and optimized FBFFT.By introducing the AFDD method and Powell optimization algorithm,this method can automatically identify the initial value of natural frequency and solve the objective function efficiently and simply.In order to verify the feasibility and effectiveness of the proposed method,it is used to identify the modal parameters of the IASC-ASCE benchmark model and the j acket platform structure model,and the Most Probable Value(MPV) of the modal parameters and their respective posterior uncertainties are successfully identified.The identification results of the IASC-ASCE benc hmark model are compared with the identification re sults of the MODE-ID method,which verifies the effectivene ss and accuracy of the proposed method for identifying modal parameters.It provides a simple and feasible method for quantifying the influence of uncertain factors such as environmental parameters on the identification results,and also provide s a reference for modal parameter identification of other large structures.

Creation and Development of Turbo-generators with Water-Cooled Stator and Rotor Windings in Shanghai Electrical Machinery Mfg Works

1. An Overview of Manufacture and Operation A turbine generator utilizing a new technology of electrical machinery industry, i.e. the windings of its stator and rotor all being inner water-cooled, was first successfully created in China and was known afterwards as a turbine generator with watercooled stator and rotor windings (Abbrev, TGWSR). The teachers from Zhejiang University came to Shanghai between

有限元仿真模拟在超声喷水无损检测用水套设计中的应用

水套在超声喷水穿透检测中具有重要作用,为设计出具有良好耦合效果的水套,减少水流紊流对声波耦合的影响,本文通过构建探头套几何模型、物理建模、数值求解的有限元仿真方法对探头水套进行流体动力学仿真。结果表明,在无整流装置下,从入水口射入的水流撞击探头套内壁,产生严重紊流,进入出水管后,紊流状态仍然保持,水流流线方向杂乱。增加整流装置后,探头套内紊流得到很好的抑制,使得进入出水管的水流流线方向趋向一致,这种现象随着整流片增多而效果越加明显。本文为后续模拟水流经过出水口后的水柱状态,特别是随着初始水流速度加大后的水柱状态,以及利用有限元多物理场模拟功能,在加入声场后,模拟紊流状况下声场的变化打下了基础。

某单缸发动机冷却系统数值模拟及优化

为研究某单缸发动机冷却系统的冷却性能及工作流量,采用CFD方法对该单缸发动机冷却系统开展流场分析及工作流量提升研究。实验结果表明:该发动机冷却系统原方案的工作流量为34 L/min,不满足当发动机转速8 000 r/min时工作流量43.75 L/min的设计要求。通过优化水套阻力和提升冷却水泵性能,冷却系统的工作流量提升至44 L/min,增幅为29.4%。研究结果可为该单缸发动机冷却系统的冷却性能评估及结构改进提供仿真数据支撑。

剪切模式对砂-钢界面特性的影响

针对海上风机导管架基础在安装过程中发生的桩土界面单向剪切行为和服役过程中发生的持续循环剪切行为,分别采用常应力和等刚度边界条件对石英砂/钙质砂开展单向和循环剪切试验,研究不同剪切模式下界面强度发挥的细观作用。结果发现:随着单向剪切距离的增加,土样破碎带厚度逐渐增大,钢界面粗糙度下降;循环剪切幅值越大,颗粒排布重塑越充分,产生的法向位移越大。在大位移单向剪切和循环剪切过程中,破碎带的存在会改变土体的初始结构,使其具有强烈方向性。由于钙质砂的硬度较低,同等粒径下其形状相比石英砂颗粒更不规则,因此其在同等剪切距离下会产生更大的破碎量,引起较大体缩,而破碎后的石英砂棱角较多,在钢界面扰动下更易发生旋转,引起大位移单向剪切后的循环剪切过程中土样剪胀增加。

被动式封隔器的国产化研发

通过对被动式封隔器结构组成、工作原理和主要功能的研究,提出国产化研发方案。对被动式封隔器的主要部件进行力学性能理论分析和仿真模拟,并针对被动式封隔器在实际运行中存在的问题进行优化设计。改进后的国产被动式封隔器顺利通过多项原型试验,并获得法国船级社(BV)审查认证。试验结果表明,国产化研发的被动式封隔器各项性能均达到设计和使用要求。被动式封隔器的成功研制及其国产化为有效降低工程项目成本、提高行业核心竞争力打下坚实基础。