The major enrichment type of shale oil in the Chang 7_(3) shale of Upper Triassic Yanchang Formation in the Ordos Basin is unknown.This paper analyzes the organic matter transformation ratio,hydrocarbon expulsion effi...The major enrichment type of shale oil in the Chang 7_(3) shale of Upper Triassic Yanchang Formation in the Ordos Basin is unknown.This paper analyzes the organic matter transformation ratio,hydrocarbon expulsion efficiency and roof/floor sealing conditions of the Chang 7_(3) shale,and evaluates the major enrichment type of shale oil in this interval.The average organic matter transformation ratio of the Chang 7_(3) shale is about 45%;in other words,more than 50%of the organic matters have not transformed to hydrocarbons,and the lower the maturity,the greater the proportion of untransformed organic matters.The cumulative hydrocarbon expulsion efficiency of the transformed hydrocarbon is 27.5% on average,and the total proportion of untransformed organic matters plus retained hydrocarbons is greater than 70%.The relative hydrocarbon expulsion efficiency of the Chang 7_(3) shale is 60%on average,that is,about 40% of hydrocarbons retain in the shale.The Chang 7_(3) shale corresponds to Chang 7_(1+2) and Chang 8 sandstones as the roof and floor,respectively,and is further overlaid by Chang 6 shale,where extensive low porosity and low permeability–tight oil reservoirs have formed in the parts with relatively good porosity and permeability.Moreover,the Chang 7_(3) shale is tested to be in a negative pressure system(the pressure coefficient of 0.80–0.85).Therefore,the roof/floor sealing conditions of the Chang 7_(3) shale are poor.The retained hydrocarbons appear mostly in absorbed status,with low mobility.It is concluded that the medium–high mature shale oil is not the major enrichment type of shale oil in the Chang 7_(3) shale,but there may be enrichment opportunity for shale oil with good mobility in the areas where the sealing conditions are good without faults and fractures and oil reservoirs are formed off Chang 7_(1+2),Chang 6 and Chang 8.Furthermore,low–medium mature shale oil is believed to have great potential and is the major enrichment type of shale oil in the Chang 7_(3) shale.It is recommended to prepare relevant in-situ conversion technologies by pilot test and figure out the resource availability and distribution.展开更多
This paper is an extension and generalization of the study carried out by [1] on the estimation of the population ratio (R) of the population means of two variables (y and x) under Simple Random Sampling (SRS) scheme,...This paper is an extension and generalization of the study carried out by [1] on the estimation of the population ratio (R) of the population means of two variables (y and x) under Simple Random Sampling (SRS) scheme, using a variable transformation of the auxiliary variable, x. All the six estimators proposed by [1] are easily identified as special cases of the proposed class of estimators. Asymptotic properties of the proposed class of estimators are derived theoretically and subsequently verified using empirical illustrations. Some of the proposed estimators are found to have relatively large gains in efficiency over the customary ratio estimator, ?for the given data set.展开更多
The aim of this study is to carry out hydrothermal alteration mapping and structural mapping using ASTER images in order to identify indices that could guide mining exploration work in the Poli area and its surroundin...The aim of this study is to carry out hydrothermal alteration mapping and structural mapping using ASTER images in order to identify indices that could guide mining exploration work in the Poli area and its surroundings. To achieve this, the ASTER images were first preprocessed to correct atmospheric effects and remove vegetation influence. Secondly, a lineament mapping was conducted by applying Discrete Wavelet Transform (DWT) algorithms to the First Principal Component Analysis (PCA1) of Visible Near-Infrared (VNIR) and Shortwave Infrared (SWIR) bands. Lastly, band ratio methods were applied to the VNIR, SWIR, and Thermal Infrared (TIR) bands to determine indices of iron oxides/hydroxides (hematite and limonite), hydroxyl-bearing minerals (chlorite, epidote, and muscovite), and the quartz index. The results obtained showed that the lineaments were mainly oriented NE-SW, ENE-WSW, and E-W, with NE-SW being the most predominant direction. Concerning hydrothermal alteration, the identified indices covered almost the entire study area and showed a strong correlation with lithological data. Overlaying the obtained lineaments with the hydrothermal alteration indices revealed a significant correlation between existing mining indices and those observed in the field. Mineralized zones generally coincided with areas of high lineament density exhibiting significant hydrothermal alteration. Based on the correlation between existing mining indices and the results of hydrothermal and structural mapping, the results obtained can then be used as a reference document for any mining exploration in the study area.展开更多
The arrival times of first teleseismic phases are difficult to be measured precisely because of slowly and gradually changed onsets and weak amplitudes. The arrival times measured manually are usually behind the real ...The arrival times of first teleseismic phases are difficult to be measured precisely because of slowly and gradually changed onsets and weak amplitudes. The arrival times measured manually are usually behind the real ones. In this paper, using the ratio method of fixed scale wavelet transformations improved by us, the arrival times for the first arrival phases (such as P and PKIKP) at the teleseismic and far-teleseismic distances were measured. The results are reasonable and reliable based on the analysis and discussion of the reliabilities and errors.展开更多
In order to study the relation between martensitic transformation temperature range AT (where AT is the difference between martensitic transformation start and finish temperature) and lattice distortion ratio (c/a...In order to study the relation between martensitic transformation temperature range AT (where AT is the difference between martensitic transformation start and finish temperature) and lattice distortion ratio (c/a) of martensitic transforma~ tion, a series of Ni46Mnz8_xGa22Co4Cux (x = 2-5) Heusler alloys is prepared by arc melting method. The vibration sample magnetometer (VSM) experiment results show that AT increases when x 〉 4 and decreases when x 〈 4 with x increasing, and the minimal AT (about 1 K) is found at x = 4. Ambient X-ray diffraction (XRD) results show that AT is proportional to c/a for non-modulated Ni46Mn28_xGa22Co4Cux (x = 2-5) martensites. The relation between AT and c/a is in agreement with the analysis result obtained from crystal lattice mismatch model. About 1000-ppm strain is found for the sample at x = 4 when heating temperature increases from 323 K to 324 K. These properties, which allow a modulation of AT and temperature-induced strain during martensitic transformation, suggest Ni46Mn24Ga22Co4Cu4 can be a promising actuator and sensor.展开更多
Extending the work carried out by [1], this paper proposes six combined-type estimators of population ratio of two variables in post-stratified sampling scheme, using variable transformation. Properties of the propose...Extending the work carried out by [1], this paper proposes six combined-type estimators of population ratio of two variables in post-stratified sampling scheme, using variable transformation. Properties of the proposed estimators were obtained up to first order approximations,(on–1), both for achieved sample configurations (conditional argument) and over repeated samples of fixed size n (unconditional argument). Efficiency conditions were obtained. Under these conditions the proposed combined-type estimators would perform better than the associated customary combined-type estimator. Furthermore, optimum estimators among the proposed combined-type estimators were obtained both under the conditional and unconditional arguments. An empirical work confirmed the theoretical results.展开更多
The study proposes, along the line of [1], six separate-type estimators for estimating the population ratio of two variables in post-stratified sampling, using variable transformation. Properties of the proposed estim...The study proposes, along the line of [1], six separate-type estimators for estimating the population ratio of two variables in post-stratified sampling, using variable transformation. Properties of the proposed estimators were obtained up to first order approximations, both for achieved sample configurations (conditional argument) and over repeated samples of fixed size n (unconditional argument). Efficiency conditions, under which the proposed separate-type estimators would perform better than the associated customary separate-type estimators in terms of having smaller mean squared errors, were obtained. Furthermore, conditions under which some of the proposed separate-type estimators would perform better than other proposed separate-type estimators were also obtained. The optimum estimators among the proposed separate-type estimators were obtained and an empirical illustration confirmed the theoretical results.展开更多
Coordination complex of a copper cyanurate(Cu(Ⅱ)-CA) was transformed into coordination polymers upon the stimulus of extra Cu(Ⅱ) through “directed Ostwald ripening”. By increasing the molar ratio of Cu(Ⅱ) to CA, ...Coordination complex of a copper cyanurate(Cu(Ⅱ)-CA) was transformed into coordination polymers upon the stimulus of extra Cu(Ⅱ) through “directed Ostwald ripening”. By increasing the molar ratio of Cu(Ⅱ) to CA, we obtained two coordination polymers with selective coordination sites: Cu(Ⅱ)-κ N(HCA)κ NCu(Ⅱ) and Cu(Ⅱ)-κ N(HCA)κ O-Cu(Ⅱ), which display disparate magnetic interactions.展开更多
As a combination device for a step-up pulse transformer and a magnetic switch,the saturable pulse transformer is widely used in pulsed-power and plasma technology.A fractional-turn ratio saturable pulse transformer is...As a combination device for a step-up pulse transformer and a magnetic switch,the saturable pulse transformer is widely used in pulsed-power and plasma technology.A fractional-turn ratio saturable pulse transformer is constructed and analyzed in this paper.Preliminary experimental results show that if the primary energy storage capacitors are charged to 300 V,an output voltage of about 19 kV can be obtained across the capacitor connected to the secondary windings of a fractional-tum ratio saturable pulse transformer.Theoretical and experimental results reveal that this kind of pulse transformer is not only able to integrate a step-up transformer and a magnetic switch into one device,but can also lower the saturable inductance of its secondary windings,thus leading to the relatively high step-up ratio of the pulse transformer.Meanwhile,the application of the fractional-turn ratio saturable pulse transformer in a μs range pulse modulator as a voltage step-up device and main switch is also included in this paper.The demonstrated experiments display that an output voltage with an amplitude of about 29 kV,and a 1.6 μs pulse width can be obtained across a 3500 Ω resistive load,based on a pulse modulator,if the primary energy storage capacitors are charged to 300 V.This compact fractional-turn ratio saturable pulse transformer can be applied in many other fields such as surface treatment,corona plasma generation and dielectric barrier discharge.展开更多
The effect of Nd addition on the structure, phase transformation and magnetic properties of FePt based alloys was investigated. The results indicated that the transition temperature from ordered FCT to disordered FCC ...The effect of Nd addition on the structure, phase transformation and magnetic properties of FePt based alloys was investigated. The results indicated that the transition temperature from ordered FCT to disordered FCC phase decreased with increasing Nd concentration, but for alloys quenched rapidly from the γ phase region into ice-water, it increased with increasing Nd. The Nd element not only effectively reduced the grain size of the ordered phase but also decreased the degree of the ordered phase and refined the grains of the FCC matrix phase. The remanence ratio and coereivity of the FePt based alloy as a function of the Nd content had maximum values, respectively.展开更多
The integrated hydraulic transformer has a compact structure and no throttling loss in the process of pressure regulation.It is widely used in the common pressure rail hydrostatic transmission system.The integrated hy...The integrated hydraulic transformer has a compact structure and no throttling loss in the process of pressure regulation.It is widely used in the common pressure rail hydrostatic transmission system.The integrated hydraulic transformer is realized by designing more than three ports on the distribution plate,and the voltage transformation characteristics of the integrated hydraulic transformer with different port numbers are different.In this paper,the influence of port number on the pressure ratio of integrated hydraulic transformer was studied,and the pressure ratio characteristics of 3⁃ports,4⁃ports,and 5⁃ports integrated hydraulic transformer were obtained,and an experimental platform was built for experimental verification,which shows that the simulation results are consistent with the experimental results and provides a theoretical basis for the design of integrated hydraulic transformer.展开更多
The technical feasibility of in situ upgrading technology to develop the enormous oil and gas resource potential in low-maturity shale is widely acknowledged.However,because of the large quantities of energy required ...The technical feasibility of in situ upgrading technology to develop the enormous oil and gas resource potential in low-maturity shale is widely acknowledged.However,because of the large quantities of energy required to heat shale,its economic feasibility is still a matter of debate and has yet to be convincingly demonstrated quantitatively.Based on the energy conservation law,the energy acquisition of oil and gas generation and the energy consumption of organic matter cracking,shale heat-absorption,and surrounding rock heat dissipation during in situ heating were evaluated in this study.The energy consumption ratios for different conditions were determined,and the factors that influence them were analyzed.The results show that the energy consumption ratio increases rapidly with increasing total organic carbon(TOC)content.For oil-prone shales,the TOC content corresponding to an energy consumption ratio of 3 is approximately 4.2%.This indicates that shale with a high TOC content can be expected to reduce the project cost through large-scale operation,making the energy consumption ratio after consideration of the project cost greater than 1.In situ heating and upgrading technology can achieve economic benefits.The main methods for improving the economic feasibility by analyzing factors that influence the energy consumption ratio include the following:(1)exploring technologies that efficiently heat shale but reduce the heat dissipation of surrounding rocks,(2)exploring technologies for efficient transformation of organic matter into oil and gas,i.e.,exploring technologies with catalytic effects,or the capability to reduce in situ heating time,and(3)establishing a horizontal well deployment technology that comprehensively considers the energy consumption ratio,time cost,and engineering cost.展开更多
In recent years,it has been evident that internet is the most effective means of transmitting information in the form of documents,photographs,or videos around the world.The purpose of an image compression method is t...In recent years,it has been evident that internet is the most effective means of transmitting information in the form of documents,photographs,or videos around the world.The purpose of an image compression method is to encode a picture with fewer bits while retaining the decompressed image’s visual quality.During transmission,this massive data necessitates a lot of channel space.In order to overcome this problem,an effective visual compression approach is required to resize this large amount of data.This work is based on lossy image compression and is offered for static color images.The quantization procedure determines the compressed data quality characteristics.The images are converted from RGB to International Commission on Illumination CIE La^(∗)b^(∗);and YCbCr color spaces before being used.In the transform domain,the color planes are encoded using the proposed quantization matrix.To improve the efficiency and quality of the compressed image,the standard quantization matrix is updated with the respective image block.We used seven discrete orthogonal transforms,including five variations of the Complex Hadamard Transform,Discrete Fourier Transform and Discrete Cosine Transform,as well as thresholding,quantization,de-quantization and inverse discrete orthogonal transforms with CIE La^(∗)b^(∗);and YCbCr to RGB conversion.Peak to signal noise ratio,signal to noise ratio,picture similarity index and compression ratio are all used to assess the quality of compressed images.With the relevant transforms,the image size and bits per pixel are also explored.Using the(n,n)block of transform,adaptive scanning is used to acquire the best feasible compression ratio.Because of these characteristics,multimedia systems and services have a wide range of possible applications.展开更多
The ever-increasing demand for oil and gas has driven its exploration in rather extreme conditions. In Lamu offshore, which is hitherto underexplored, most of the wells already drilled turned out dry save for a few we...The ever-increasing demand for oil and gas has driven its exploration in rather extreme conditions. In Lamu offshore, which is hitherto underexplored, most of the wells already drilled turned out dry save for a few wells with hydrocarbon shows despite the promising reservoir properties and related geological structures. This, therefore, necessitated a source rock evaluation study in the area to ascertain the presence and potential of the source rock by integrating the geochemical data analysis and petroleum system modeling. The shallow Lamu offshore source rock quantity, quality, and maturity have been estimated through the determination of the total organic carbon (TOC) average values, Kerogen typing, and Rock-Eval pyrolysis measurements respectively. Geochemical data for Kubwa-1, Mbawa-1, Pomboo-1, and Simba-1 were evaluated for determining the source rock potential for hydrocarbon generation. Petroleum system modeling was applied in evaluating geological conditions necessary for a successful charge within a software that integrated geochemical and petrophysical characterization of the sedimentary formations in conjunction with boundary conditions that include basal heat flow, sediment-water interface temperature, and Paleo-water depth. The average TOC of 0.89 wt % in the study area suggests a fair organic richness which seems higher in the late cretaceous (0.98 wt %) than in the Paleocene (0.81 wt %). Vitrinite reflectance and T<sub>max</sub> values in the study area indicate the possible presence of both mature and immature source rocks. Type III Kerogen was the most dominant Kerogen type, and gas shows are the most frequent hydrocarbon encountered in the Lamu Basin with a few cases registering type II/III and type II. The charge properties (i.e. Temperature, transformation ratio, and Vitrinite reflectance) over geologic time at each of the wells have been estimated and their spatial variation mapped as seen from the burial history and depth curves overlaid with temperature, transformation ratio, and Vitrinite reflectance respectively. From the upper cretaceous maturity maps, the results seem to favor near coastal regions where average TOC is about 1.4 wt %, Vitrinite reflectance is more than 0.5%, transformation ratio is more than 10%, and temperatures range from 80°C to 160°C. The results postulate the absence of a definitive effective source rock with a likelihood of having cases of potential and possible source rocks. Moreover, greater uncertainty rests on the source rock’s presence and viability tending toward the deep offshore. Geochemical analysis and petroleum system modeling for hydrocarbon source rock evaluation improved the understanding of the occurrence of the possible and potential source rocks and processes necessary for hydrocarbon generation.展开更多
In this paper, a method to calculate the slope of the ratio restraint characteristic of a transformer differential relay protection is proposed. The method allows using some concise but effective means to get the slop...In this paper, a method to calculate the slope of the ratio restraint characteristic of a transformer differential relay protection is proposed. The method allows using some concise but effective means to get the slope. Modulating the argument of current output from ONLLY testing equipment can make the relay protection device operate, thus, the data used for calculation would be obtained naturally after several trails. In order to make sure how effective that method could be, some experiment data is given as well.展开更多
基金Supported by the National Natural Science Foundation of China(U22B6004).
文摘The major enrichment type of shale oil in the Chang 7_(3) shale of Upper Triassic Yanchang Formation in the Ordos Basin is unknown.This paper analyzes the organic matter transformation ratio,hydrocarbon expulsion efficiency and roof/floor sealing conditions of the Chang 7_(3) shale,and evaluates the major enrichment type of shale oil in this interval.The average organic matter transformation ratio of the Chang 7_(3) shale is about 45%;in other words,more than 50%of the organic matters have not transformed to hydrocarbons,and the lower the maturity,the greater the proportion of untransformed organic matters.The cumulative hydrocarbon expulsion efficiency of the transformed hydrocarbon is 27.5% on average,and the total proportion of untransformed organic matters plus retained hydrocarbons is greater than 70%.The relative hydrocarbon expulsion efficiency of the Chang 7_(3) shale is 60%on average,that is,about 40% of hydrocarbons retain in the shale.The Chang 7_(3) shale corresponds to Chang 7_(1+2) and Chang 8 sandstones as the roof and floor,respectively,and is further overlaid by Chang 6 shale,where extensive low porosity and low permeability–tight oil reservoirs have formed in the parts with relatively good porosity and permeability.Moreover,the Chang 7_(3) shale is tested to be in a negative pressure system(the pressure coefficient of 0.80–0.85).Therefore,the roof/floor sealing conditions of the Chang 7_(3) shale are poor.The retained hydrocarbons appear mostly in absorbed status,with low mobility.It is concluded that the medium–high mature shale oil is not the major enrichment type of shale oil in the Chang 7_(3) shale,but there may be enrichment opportunity for shale oil with good mobility in the areas where the sealing conditions are good without faults and fractures and oil reservoirs are formed off Chang 7_(1+2),Chang 6 and Chang 8.Furthermore,low–medium mature shale oil is believed to have great potential and is the major enrichment type of shale oil in the Chang 7_(3) shale.It is recommended to prepare relevant in-situ conversion technologies by pilot test and figure out the resource availability and distribution.
文摘This paper is an extension and generalization of the study carried out by [1] on the estimation of the population ratio (R) of the population means of two variables (y and x) under Simple Random Sampling (SRS) scheme, using a variable transformation of the auxiliary variable, x. All the six estimators proposed by [1] are easily identified as special cases of the proposed class of estimators. Asymptotic properties of the proposed class of estimators are derived theoretically and subsequently verified using empirical illustrations. Some of the proposed estimators are found to have relatively large gains in efficiency over the customary ratio estimator, ?for the given data set.
文摘The aim of this study is to carry out hydrothermal alteration mapping and structural mapping using ASTER images in order to identify indices that could guide mining exploration work in the Poli area and its surroundings. To achieve this, the ASTER images were first preprocessed to correct atmospheric effects and remove vegetation influence. Secondly, a lineament mapping was conducted by applying Discrete Wavelet Transform (DWT) algorithms to the First Principal Component Analysis (PCA1) of Visible Near-Infrared (VNIR) and Shortwave Infrared (SWIR) bands. Lastly, band ratio methods were applied to the VNIR, SWIR, and Thermal Infrared (TIR) bands to determine indices of iron oxides/hydroxides (hematite and limonite), hydroxyl-bearing minerals (chlorite, epidote, and muscovite), and the quartz index. The results obtained showed that the lineaments were mainly oriented NE-SW, ENE-WSW, and E-W, with NE-SW being the most predominant direction. Concerning hydrothermal alteration, the identified indices covered almost the entire study area and showed a strong correlation with lithological data. Overlaying the obtained lineaments with the hydrothermal alteration indices revealed a significant correlation between existing mining indices and those observed in the field. Mineralized zones generally coincided with areas of high lineament density exhibiting significant hydrothermal alteration. Based on the correlation between existing mining indices and the results of hydrothermal and structural mapping, the results obtained can then be used as a reference document for any mining exploration in the study area.
基金National Natural Science Foundation of China (40074007).
文摘The arrival times of first teleseismic phases are difficult to be measured precisely because of slowly and gradually changed onsets and weak amplitudes. The arrival times measured manually are usually behind the real ones. In this paper, using the ratio method of fixed scale wavelet transformations improved by us, the arrival times for the first arrival phases (such as P and PKIKP) at the teleseismic and far-teleseismic distances were measured. The results are reasonable and reliable based on the analysis and discussion of the reliabilities and errors.
基金Project supported by the National Key Project of Fundamental Research of China(Grant No.2012CB932304)the National Natural Science Foundation of China(Grant No.U1232210)
文摘In order to study the relation between martensitic transformation temperature range AT (where AT is the difference between martensitic transformation start and finish temperature) and lattice distortion ratio (c/a) of martensitic transforma~ tion, a series of Ni46Mnz8_xGa22Co4Cux (x = 2-5) Heusler alloys is prepared by arc melting method. The vibration sample magnetometer (VSM) experiment results show that AT increases when x 〉 4 and decreases when x 〈 4 with x increasing, and the minimal AT (about 1 K) is found at x = 4. Ambient X-ray diffraction (XRD) results show that AT is proportional to c/a for non-modulated Ni46Mn28_xGa22Co4Cux (x = 2-5) martensites. The relation between AT and c/a is in agreement with the analysis result obtained from crystal lattice mismatch model. About 1000-ppm strain is found for the sample at x = 4 when heating temperature increases from 323 K to 324 K. These properties, which allow a modulation of AT and temperature-induced strain during martensitic transformation, suggest Ni46Mn24Ga22Co4Cu4 can be a promising actuator and sensor.
文摘Extending the work carried out by [1], this paper proposes six combined-type estimators of population ratio of two variables in post-stratified sampling scheme, using variable transformation. Properties of the proposed estimators were obtained up to first order approximations,(on–1), both for achieved sample configurations (conditional argument) and over repeated samples of fixed size n (unconditional argument). Efficiency conditions were obtained. Under these conditions the proposed combined-type estimators would perform better than the associated customary combined-type estimator. Furthermore, optimum estimators among the proposed combined-type estimators were obtained both under the conditional and unconditional arguments. An empirical work confirmed the theoretical results.
文摘The study proposes, along the line of [1], six separate-type estimators for estimating the population ratio of two variables in post-stratified sampling, using variable transformation. Properties of the proposed estimators were obtained up to first order approximations, both for achieved sample configurations (conditional argument) and over repeated samples of fixed size n (unconditional argument). Efficiency conditions, under which the proposed separate-type estimators would perform better than the associated customary separate-type estimators in terms of having smaller mean squared errors, were obtained. Furthermore, conditions under which some of the proposed separate-type estimators would perform better than other proposed separate-type estimators were also obtained. The optimum estimators among the proposed separate-type estimators were obtained and an empirical illustration confirmed the theoretical results.
基金the financial support from the Australian Research Council (No.DP190101607)National Natural Science Foundation of China (No.21971203)。
文摘Coordination complex of a copper cyanurate(Cu(Ⅱ)-CA) was transformed into coordination polymers upon the stimulus of extra Cu(Ⅱ) through “directed Ostwald ripening”. By increasing the molar ratio of Cu(Ⅱ) to CA, we obtained two coordination polymers with selective coordination sites: Cu(Ⅱ)-κ N(HCA)κ NCu(Ⅱ) and Cu(Ⅱ)-κ N(HCA)κ O-Cu(Ⅱ), which display disparate magnetic interactions.
基金supported by National Natural Science Foundation of China under Grant Nos.51477177 and 51641707
文摘As a combination device for a step-up pulse transformer and a magnetic switch,the saturable pulse transformer is widely used in pulsed-power and plasma technology.A fractional-turn ratio saturable pulse transformer is constructed and analyzed in this paper.Preliminary experimental results show that if the primary energy storage capacitors are charged to 300 V,an output voltage of about 19 kV can be obtained across the capacitor connected to the secondary windings of a fractional-tum ratio saturable pulse transformer.Theoretical and experimental results reveal that this kind of pulse transformer is not only able to integrate a step-up transformer and a magnetic switch into one device,but can also lower the saturable inductance of its secondary windings,thus leading to the relatively high step-up ratio of the pulse transformer.Meanwhile,the application of the fractional-turn ratio saturable pulse transformer in a μs range pulse modulator as a voltage step-up device and main switch is also included in this paper.The demonstrated experiments display that an output voltage with an amplitude of about 29 kV,and a 1.6 μs pulse width can be obtained across a 3500 Ω resistive load,based on a pulse modulator,if the primary energy storage capacitors are charged to 300 V.This compact fractional-turn ratio saturable pulse transformer can be applied in many other fields such as surface treatment,corona plasma generation and dielectric barrier discharge.
基金Project supported by the National Natural Science Foundation of China (50261002 ,10574049)
文摘The effect of Nd addition on the structure, phase transformation and magnetic properties of FePt based alloys was investigated. The results indicated that the transition temperature from ordered FCT to disordered FCC phase decreased with increasing Nd concentration, but for alloys quenched rapidly from the γ phase region into ice-water, it increased with increasing Nd. The Nd element not only effectively reduced the grain size of the ordered phase but also decreased the degree of the ordered phase and refined the grains of the FCC matrix phase. The remanence ratio and coereivity of the FePt based alloy as a function of the Nd content had maximum values, respectively.
基金the National Key Research and Development Plan Projects(Grant No.2018YFB2001200)the Natural Science Foundation of the Jiangsu Higher Education Institutions of China(Grant Nos.19KJB460026,19KJA140002)the Six Talent Peak Training Projects in Jiangsu Province(Grant No.JXQC-36).
文摘The integrated hydraulic transformer has a compact structure and no throttling loss in the process of pressure regulation.It is widely used in the common pressure rail hydrostatic transmission system.The integrated hydraulic transformer is realized by designing more than three ports on the distribution plate,and the voltage transformation characteristics of the integrated hydraulic transformer with different port numbers are different.In this paper,the influence of port number on the pressure ratio of integrated hydraulic transformer was studied,and the pressure ratio characteristics of 3⁃ports,4⁃ports,and 5⁃ports integrated hydraulic transformer were obtained,and an experimental platform was built for experimental verification,which shows that the simulation results are consistent with the experimental results and provides a theoretical basis for the design of integrated hydraulic transformer.
文摘The technical feasibility of in situ upgrading technology to develop the enormous oil and gas resource potential in low-maturity shale is widely acknowledged.However,because of the large quantities of energy required to heat shale,its economic feasibility is still a matter of debate and has yet to be convincingly demonstrated quantitatively.Based on the energy conservation law,the energy acquisition of oil and gas generation and the energy consumption of organic matter cracking,shale heat-absorption,and surrounding rock heat dissipation during in situ heating were evaluated in this study.The energy consumption ratios for different conditions were determined,and the factors that influence them were analyzed.The results show that the energy consumption ratio increases rapidly with increasing total organic carbon(TOC)content.For oil-prone shales,the TOC content corresponding to an energy consumption ratio of 3 is approximately 4.2%.This indicates that shale with a high TOC content can be expected to reduce the project cost through large-scale operation,making the energy consumption ratio after consideration of the project cost greater than 1.In situ heating and upgrading technology can achieve economic benefits.The main methods for improving the economic feasibility by analyzing factors that influence the energy consumption ratio include the following:(1)exploring technologies that efficiently heat shale but reduce the heat dissipation of surrounding rocks,(2)exploring technologies for efficient transformation of organic matter into oil and gas,i.e.,exploring technologies with catalytic effects,or the capability to reduce in situ heating time,and(3)establishing a horizontal well deployment technology that comprehensively considers the energy consumption ratio,time cost,and engineering cost.
文摘In recent years,it has been evident that internet is the most effective means of transmitting information in the form of documents,photographs,or videos around the world.The purpose of an image compression method is to encode a picture with fewer bits while retaining the decompressed image’s visual quality.During transmission,this massive data necessitates a lot of channel space.In order to overcome this problem,an effective visual compression approach is required to resize this large amount of data.This work is based on lossy image compression and is offered for static color images.The quantization procedure determines the compressed data quality characteristics.The images are converted from RGB to International Commission on Illumination CIE La^(∗)b^(∗);and YCbCr color spaces before being used.In the transform domain,the color planes are encoded using the proposed quantization matrix.To improve the efficiency and quality of the compressed image,the standard quantization matrix is updated with the respective image block.We used seven discrete orthogonal transforms,including five variations of the Complex Hadamard Transform,Discrete Fourier Transform and Discrete Cosine Transform,as well as thresholding,quantization,de-quantization and inverse discrete orthogonal transforms with CIE La^(∗)b^(∗);and YCbCr to RGB conversion.Peak to signal noise ratio,signal to noise ratio,picture similarity index and compression ratio are all used to assess the quality of compressed images.With the relevant transforms,the image size and bits per pixel are also explored.Using the(n,n)block of transform,adaptive scanning is used to acquire the best feasible compression ratio.Because of these characteristics,multimedia systems and services have a wide range of possible applications.
文摘The ever-increasing demand for oil and gas has driven its exploration in rather extreme conditions. In Lamu offshore, which is hitherto underexplored, most of the wells already drilled turned out dry save for a few wells with hydrocarbon shows despite the promising reservoir properties and related geological structures. This, therefore, necessitated a source rock evaluation study in the area to ascertain the presence and potential of the source rock by integrating the geochemical data analysis and petroleum system modeling. The shallow Lamu offshore source rock quantity, quality, and maturity have been estimated through the determination of the total organic carbon (TOC) average values, Kerogen typing, and Rock-Eval pyrolysis measurements respectively. Geochemical data for Kubwa-1, Mbawa-1, Pomboo-1, and Simba-1 were evaluated for determining the source rock potential for hydrocarbon generation. Petroleum system modeling was applied in evaluating geological conditions necessary for a successful charge within a software that integrated geochemical and petrophysical characterization of the sedimentary formations in conjunction with boundary conditions that include basal heat flow, sediment-water interface temperature, and Paleo-water depth. The average TOC of 0.89 wt % in the study area suggests a fair organic richness which seems higher in the late cretaceous (0.98 wt %) than in the Paleocene (0.81 wt %). Vitrinite reflectance and T<sub>max</sub> values in the study area indicate the possible presence of both mature and immature source rocks. Type III Kerogen was the most dominant Kerogen type, and gas shows are the most frequent hydrocarbon encountered in the Lamu Basin with a few cases registering type II/III and type II. The charge properties (i.e. Temperature, transformation ratio, and Vitrinite reflectance) over geologic time at each of the wells have been estimated and their spatial variation mapped as seen from the burial history and depth curves overlaid with temperature, transformation ratio, and Vitrinite reflectance respectively. From the upper cretaceous maturity maps, the results seem to favor near coastal regions where average TOC is about 1.4 wt %, Vitrinite reflectance is more than 0.5%, transformation ratio is more than 10%, and temperatures range from 80°C to 160°C. The results postulate the absence of a definitive effective source rock with a likelihood of having cases of potential and possible source rocks. Moreover, greater uncertainty rests on the source rock’s presence and viability tending toward the deep offshore. Geochemical analysis and petroleum system modeling for hydrocarbon source rock evaluation improved the understanding of the occurrence of the possible and potential source rocks and processes necessary for hydrocarbon generation.
文摘In this paper, a method to calculate the slope of the ratio restraint characteristic of a transformer differential relay protection is proposed. The method allows using some concise but effective means to get the slope. Modulating the argument of current output from ONLLY testing equipment can make the relay protection device operate, thus, the data used for calculation would be obtained naturally after several trails. In order to make sure how effective that method could be, some experiment data is given as well.