Study on preparation and gas sensing property of water-soluble polyaniline/SmBaCuMO_(5+δ)(M=Fe, Co, Ni) for NH_3

Water-soluble polyaniline （PANI）, prepared by chemical-oxide and SmBaCuMO5＋δ（M=Fe, Co, Ni）（SBCM） powders, pre-pared by sol-gel method were analyzed through Fourier transform infrared spectroscopy （FT-IR） spectra, X-ray diffraction （XRD）, transmission electron microscopy （TEM） and energy dispersive spectroscopy （EDS） respectively, so as to investigate the gas sensi-tivities of PANI/SmBaCuFeO5＋δ（SBCF） and its sensitivity to NH3 under room temperature. The results showed that all of SBCM powders were of double-perovskite structure and PANI was successfully obtained. Under the same condition, the gas sensor based on PANI/SmBaCuFeO5＋δ（SBCF） material exhibited higher resistance sensitivity, better selectivity and shorter response-recovery time than others. The resistance sensitivities to NH3 increased with the increasing of atom radius of M in PANI/SBCM.

Effect and mechanism of reductive polyaniline on the stability of nitrocellulose

The search for new green and efficient stabilizers is of great importance for the stabilization of nitrocellulose(NC). This is due to the shortcomings of traditional stabilizers, such as high toxicity. In this study, reduced polyaniline(r-PANI), which has a similar functional structure to diphenylamine(DPA) but is non-toxic, was prepared from PANI based on the action with N_(2)H_(4) and NH_(3)-H_(2)O, and used for the first time as a potential stabilizer for NC. XPS, FTIR, Raman, and SEM were used to characterize the reduced chemical structure and surface morphology of r-PANI. In addition, the effect of r-PANI on the stabilization of NC was characterized using DSC, VST, isothermal TG, and MMC. Thermal weight loss was reduced by 83% and 68% and gas pressure release by 75% and 49% compared to pure NC and NC&3%DPA, respectively.FTIR and XPS were used to characterize the structural changes of r-PANI before and after reaction with NO_(2). The 1535 cm^(-1) and 1341 cm^(-1) of the FTIR and the 404.98 eV and 406.05 eV of the XPS showed that the -NO_(2) was generated by the absorption of NO_(2). Furthermore, the quantum chemical calculation showed that NO_(2) was directly immobilized on r-PANI by forming -NO_(2) in the neighboring position of the benzene ring.

Surface Morphology and Thermo-Electrical Energy Analysis of Polyaniline (PANI) Incorporated Cotton Fabric

With the exponential development in wearable electronics,a significant paradigm shift is observed from rigid electronics to flexible wearable devices.Polyaniline(PANI)is considered as a dominant material in this sector,as it is endowed with the optical properties of both metal and semiconductors.However,its widespread application got delineated because of its irregular rigid form,level of conductivity,and precise choice of solvents.Incorporating PANI in textile materials can generate promising functionality for wearable applications.This research work employed a straightforward in-situ chemical oxidative polymerization to synthesize PANI on Cotton fabric surfaces with varying dopant(HCl)concentrations.Pre-treatment using NaOH is implemented to improve the conductivity of the fabric surface by increasing the monomer absorption.This research explores the morphological and structural analysis employing SEM,FTIR and EDX.The surface resistivity was measured using a digital multimeter,and thermal stability is measured using TGA.Upon successful polymerization,a homogenous coating layer is observed.It is revealed that the simple pre-treatment technique significantly reduces the surface resistivity of Cotton fabric to 1.27 kΩ/cm with increasing acid concentration and thermal stability.The electro-thermal energy can also reach up to 38.2°C within 50 s with a deployed voltage of 15 V.The modified fabric is anticipated to be used in thermal regulation,supercapacitor,sensor,UV shielding,antimicrobial and other prospective functional applications.

Release Model of Water-soluble Chitosan Nanoparticles for Protein Delivery

[Objective] The experiment aimed to explore release rule of water-soluble chitosan (WSC) in vitro. [Method]The bovine serum albumin(BSA) was taken as a model protein drug and some existing release models such as Kinetics model, Gompertz model, Weibull model, Higuchi model and Logistic model were used to fit the BSA release profile from WSC carriers. [Result] Except Higuchi model and Logistic model, other models could fit BSA release profile better. [Conclusion] Gompertz two-order kinetics model could fit the release of WSC nano-particles better and model parameters had practical physical meaning.

Synthesis of Chiral Polyaniline Induced by Modified Hemoglobin

The synthesis of chiral polyaniline （PANI） induced by modified hemoglobin （Hb） was pro- foundly explored for the first time. Results revealed that after being separated, inactivated or immobilized, Hb can still induce the formation of chiral PANI successfully, suggesting that Hb can be used as the chiral inducers regardless of harsh reaction conditions. By examining the properties of PANI induced by modified Hb, it was found that Hb（inactivated）-PANI possessed excellent chirality, stability, and crystalline structure. The globin separated from Hb was demonstrated to have the ability of inducing the production of chiral PANI whereas the hematin from Hb had no capacity to direct enantio specificity for the PANI chains. Results indicated that Hb（immobilized）-PANI exhibited poor yield, doping state, and crys- talline structure, indicating that the immobilization of Hb by entrapment was not beneficial to the polymerization reaction. Results also showed that the structure of Hb may have significant effects on the morphologies of chiral PANI.

A study of the properties of hydrophobically associating water-soluble polymers used in drilling fluids

Hydrophobically associating water-soluble polymers (HPAP) have been synthesized from acrylamide(AM), acrylate (AA), 2-acrylamido-2-methyl propane sulfonic acid (AMPS) and hydrophobic monomer (AP) in aqueous solution by radical polymerization. New polymer drilling fluids are made up of HPAP, which is used as viscosifiers and encapsulation agents. Properties of this system are reported in this paper. Results indicate that this system has a high value of yield point to plastic viscosity (YP/PV≥0.7), high viscosity at a low-shear rate (LSRV≥30000mPa·s), excellent shear thinning behavior, good solid-carrying behavior, resistance to shear, good thermal stability (as high as 140℃) and salt resistance. The system has excellent behavior in high-density solution of NaCl and in calcium and magnesium rich saline solutions. Hence, HPAP also can be used in saltwater polymer drilling fluids.

PREPARATION OF POLYANILINE/ACETYLENE BLACK COMPOSITE AS HOLE CONDUCTOR IN SOLID-STATE DYE-SENSITIZED SOLAR CELL

A clay-like conductive material comprising polyaniline（PANI）-acetylene black particles is fabricated as a hole conductor for dye sensitized solar cell（DSSC）.The results show that the introduction of acetylene black into the polymer electrolyte improves the photovoltaic behavior of solid-state DSSC,owing to the increase of the hole mobility of PANI electrolyte,the improvement of the wetting quality of the composite electrolyte,and the reinforcement of interface contact between electrode and the electrolyte.Finally,the overall energy conversion efficiency of DSSC with PANI-50%（in weight）acetylene black electrolyte is 48% of that of liquid DSSC.Therefore,the PANI-acetylene black composition is a credible alternative to hole conductor in application of solid DSSC.

Effect of Different Environmental Conditions on Algicidal Effect of Water-soluble Extracts of Chinese Chive

[Objective] The paper was to study the algicidal effect of water-soluble extracts of Chinese chive under different environmental conditions, so as to provide reference for further study and development of new algicidal substances. [Method] The effects of water-soluble extracts of Chinese chive on the growth of Microcystis aeruginosa under different pH, light and aeration conditions were compared and studied. [Result] The growth inhibition rate of water-soluble extracts of Chinese chive on M. aeruginosa was greater than 90% under different pH conditions. With the growth of M. aeruginosa, the culture liquid with different initial pH was finally tended to 9-9.5. The growth inhibition rate of water-soluble extracts of Chinese chive on algae cell increased with the prolongation of culture time within the light intensity range of 1 000-4 000 lx. The inhibition effect of water-soluble extracts of Chinese chive on M. aeruginosa under low light intensity（1 000 lx）was better than that under high light intensity, the best light intensity for growth was not conducive to the exertion of allelopathic effect. Meanwhile, aeration condition was more conducive to the inhibition effect of water-soluble extracts of Chinese chive on the growth of M. aeruginosa. [Conclusion] pH, light and aeration conditions all affected the inhibition effect of water-soluble extracts of Chinese chive treated by high temperature on M. aeruginosa. Understanding the effect of these environmental factors on algicidal effect of allelochemicals could provide reference for further study and development of new algicidal substances.

Effect of thatch on water-soluble phosphorus of pasture soil fertilized with broiler litter

The presence of a thatch layer in established pastures could reduce the contact between broiler litter and soil, thus increasing the potential for surface runoff contamination with litter P. We conducted a laboratory study to evaluate the effect of a thatch layer on the dynamics of water-soluble P in undisturbed cores taken from a pasture. Cores with and without a thatch layer received a surface application of broiler litter (5 thm-2) and were incubated at 25 oC for 56 d. The result showed that on the soil surface the contents of water soluble-P (39 kghm-2) of the cores with the thatch layer was higher than that (20 kghm-2) of the cores without the thatch layer. Therefore on well-established pastures fertilized with broiler litter, the presence of a thatch layer might lead to high concentrations of water-soluble P on the soil surface.

Palladium nanoparticles in cross-linked polyaniline as highly efficient catalysts for Suzuki-Miyaura reactions

Palladium nanoparticles supported on cross-linked polyaniline with bulky phosphorus ligands were developed.These catalysts showed high efficiency in the Suzuki-Miyaura reaction of aryl chlorides and bromides with phenylboronic acids.Aryl chlorides and bromides with functional groups,such as CN,MeO,CHO,MeCO and NO_2,were converted to the corresponding biphenyls in high yields with catalyst loading.Additionally,the catalysts combined high activity with good reusability;they could be used at least five times for the Suzuki-Miyaura coupling reaction.

Fe^(3+)/Fe^(2+) redox electrolyte for high-performance polyaniline/SnO_2 supercapacitors

The Fe3＋/Fe2＋ redox electrolyte for use in polyaniline/tin oxide （PANI/SnO2）supercapacitors was reported. The influences of redox electrolyte based on different Fe3＋/Fe2＋ ion pair concentrations in 1 mol/LH2SO4 solution on the pseudocapacitive behaviors of PANI/SnO2 supercapacitor were investigated. The electrochemical properties of the supercapacitor were studied by cyclic voltammetry （CV）, galvanostatic charge discharge （GCD）, and electrochemical impedance spectroscopy （EIS） techniques. It is found that the performance of the supercapacitor is the best when the Fe3＋/Fe2＋ concentrationis 0.4 mol/L and its initial specific capacitance is 1172 F/g at an applied current density of 1 A/g. The long-term cycling experiment shows good stability with the retention of initial capacitance values of 88% after 2000 galvanostatic cycles. The experimental results testify that using Fe3＋/Fe2＋ redox electrolyte has a good prospect for improving the performances of energy-storage devices.

Electrochemical Behavior and Specific Capacitance of Polyaniline/Silver Nanoparticle/Multi-walled Carbon Nanotube Composites

In this work, we fabricated the polyaniline/silver nanoparticle/multi-walled carbon nanotube （PANI/Ag/MWCNT） composites by in situ polymerization of aniline on the wall of Ag/MWCNTs with different aniline to Ag/MWCNT mass ratios. The chemical structure of the ternary composites was characterized by Fourier transform infrared spectroscopy, Xray diffraction, and X-ray photoelectron spectroscopy. Scanning electron microscope and high-resolution transmission electron microscopy were used to observe the morphology of the ternary composites. The results showed that the polyaniline PANI layer was prepared successfully and it covered Ag/MWCNTs completely. In addition, Ag nanoparticles between the MWCNT core and the PANI layer existed in the form of elemental crystal, which could contribute to the electrochemical performance of the composites. Then we prepared the composite electrodes and studied their electrochemical behaviors in 1 mol/L KOH. It was found that these composite electrodes had very low impedance, and exhibited lower resistance, higher electrochemical activity, and better cyclic stability compared with pure PANI electrode. Particularly, when the mass ratio of aniline to Ag/MWCNTs was 5：5, the composite electrode displayed a small equivalent series resistance （0.23 Ω） and low interfacial charge transfer resistance （〈0.25 Ω）, as well as 160 F/g of the maximum specific capacitance at a current density of 0.25 A/g in KOH solution. We could conclude that the composite material had potential applications as cathode materials for lithium batteries and supercapacitors.

A novel polyaniline/mesoporous carbon nano-composite electrode for asymmetric supercapacitor

A novel nano-composite of polyaniline/mesoporous carbon（PANI/CMK-3） was prepared with mesoporous carbon（CMK-3） serving as the support.Electrochemical asymmetric capacitors have been successfully designed by using PANI/CMK-3 composite and CMK-3 as positive and negative electrode,respectively.The results showed that the discharge capacity of the asymmetric capacitor could reach 87.4 F/g under the current density of 5 mA/cm^2 and cell voltage of 1.4 V.The energy density of the asymmetric capacitor was up to 23.8 Wh/kg with a power density of 206 W/kg.Furthermore,PANI/CMK-3-CMK-3 asymmetric capacitor using this PANI/CMK-3 nano-composite could be activated quickly and possess high charge-discharge efficiency.

Platinum-polyaniline-modified carbon fiber electrode for the electrooxidation of methanol

Platinum was electrodeposited onto a polyaniline-modified carbon fiberelectrode by the cyclic voltammetric method in sulfuric acid, which may enable an increase in thelevel of platinum utilization currently achieved in electrocatalytic systems. This electrodepreparation consists of a two-step procedure: first electropolymerization of aniline onto carbonfiber and then electrodeposition of platinum. The catalytic activity of theplatinum-polyanihne-modified carbon fiber electrode (Pt/PAni/C) was compared with that of a barecarbon fiber electrode (Pt/C) by the oxidation of methanol. The maximum oxidation current ofmethanol on Pt/PAni/C is 50.7 mA centre dot cm^(-2), which is 6.7 times higher than 7.6 mA centredot cm^(-2) on the Pt/C. Scanning electron microscopy was used to investigate the dispersion of theplatinum particles of about 0.4 um.

A flexible solid-state supercapacitor based on graphene/polyaniline paper electrodes

The direct coating of graphene sheets obtained by electrochemical exfoliation on commercial paper renders the preparation of highly conductive flexible paper substrate for subsequent deposition of polyaniline (PANi) nanorods via electrochemical polymerization. The deposit ion of PANi can be well-controlled by adjusting the electrochemical polymerization time, leading to the formation of PANi coated graphene paper (PANi-GP). The as-prepared electrode exhibited high areal capacitance of 176 mF cm^-2 in three-electrode system at a current density of 0.2 mA cm^-2 which is around 10 times larger than that of pris-tine graphene paper due to the pseudocapacitive behavior of PANi. In-situ Raman test was used to determine the molecular changes during redox process of PANi. More importantly, all-solid-state symmetric capacitor assembled with two PANi-GP electrodes in a polymer electrolyte delivered an areal capacitanee of 123 mF cm^-2, corresponding to an areal energy density of 17.1 μWh cm^-2 and an areal power density of 0.25 mW cm^-2. The symmetric capacitor held a capacitive retention of 74.8% after 500 bending tests from 0 to 120°, suggesting the good flexibility and mechanical stability. These results showed the great promising application in flexible energy-storage devices.

Antibacterial Effect of the Conducting Polyaniline

Excellent antibacterial performance of polyaniline （PAni） against Escherichia coli and Gram-positive Staphylococcus aureus microorganisms has been demonstrated under both dark and visible light conditions. The electrostatic adherence between the PAni molecules and the bacteria may play a very important role for the antibacterial reaction of the PAni. As a result of our investigation, conducting PAni and its composites/blends are believed to be useful as a new type of antibacterial agent, self-clean as well as multifunctional material for improving the human health and living environment.

Polyaniline Formed in Alkaline Solution─A New Luminous Material

Electropolymerization of aniline in KOH solution and properties of the polymer are studied by using in situ reflex ellipsometry, cyclic voltammetry and fluorescence spectroscopic method. The change patterns of ellipsometric parameters and the thickness of film in the process of electropolymerization are investigated. The complex refractive indices and the fluorescence spectra of PAN indicate that the PAN is a new kind of luminous material.

Preparation of a Novel Acid Doped Polyaniline Adsorbent for Removal of Anionic Pollutant from Wastewater

Polyaniline(PANI) was one of the most extensively studied adsorbents due to its low cost and good environmental stability. The objective of the current study was to improve the selective capabilities of PANI for anionic dyes. We found that the acid doped PANI prepared with hydrochloric acid and p-toluenesulfonic acid(PTSA) could selectively adsorb anionic dyes. It exhibited very good selectivity for OG dye, the mechanism was proposed based on the chemical interaction of PANI with the sulfonate group of the dyes. The effects of solution p H, initial dye concentration, and different HCl/PTSA mole ratios on the adsorption capacity of OG have been investigated. Kinetic simulations indicated that the adsorption process could be well represented by pseudo-second-order kinetic plots. The isothermal adsorption curve fitting also showed that the adsorption process could be well described by the Langmuir isothermal equation. The results showed that acid doped PANI could be employed as a promising adsorbent for anion removal from dye wastewater.

Fabrication of Polyaniline/Silver Nanocomposite Under Gamma-ray Irradiation

Polyaniline （PANI）/silver composite was one-step synthesized under γ-ray irradiation. The structure of the composite was characterized by Fourier transform infrared spectroscopy, UV-Visible, and X-ray diffraction, which indicated that PANI and face-centered-cubic silver were synthesized under γ-ray irradiation. The reaction mechanism were discussed, which revealed that the PANI was formed by the reaction of aniline cation radicals formed by the reaction of aniline cation and -OH, and Ag was formed by the reaction of Ag＋ and eaq. The morphology of the composite consisted of PANI nanofibers and Ag nanoparticles, and the mechanism of the morphology formation was discussed, which revealed that the rapid mixing like polymerization process might play an important role. It was revealed that the transport behavior of the composite well fitted with the variable-range-hopping model in 80-300 K and deviated from the model below 80 K.

Electrodeposition and Characterization of Polyaniline Film

Abstract Polyaniline film was prepared by electrochemical method in an acidic solution of aniline. The micromor- phology of the polyaniline film was transformed to three-dimensional network structure instead of little particles while the deposition time was extended. The peak wavelength of the photoluminescence spectrum was 491 nm. The luminous intensity increased with the extension of deposition time, and so did the electrochemical activity.