Analysis for Effects of Temperature Rise of PV Modules upon Driving Distance of Vehicle Integrated Photovoltaic Electric Vehicles

The development of vehicle integrated photovoltaics-powered electric vehicles (VIPV-EV) significantly reduces CO2 emissions from the transport sector to realize a decarbonized society. Although long-distance driving of VIPV-EV without electricity charging is expected in sunny regions, driving distance of VIPV-EV is affected by climate conditions such as solar irradiation and temperature rise of PV modules. In this paper, detailed analytical results for effects of climate conditions such as solar irradiation and temperature rise of PV modules upon driving distance of the VIPV-EV were presented by using test data for Toyota Prius and Nissan Van demonstration cars installed with high-efficiency InGaP/GaAs/InGaAs 3-junction solar cell modules with a module efficiency of more than 30%. The temperature rise of some PV modules studied in this study was shown to be expressed by some coefficients related to solar irradiation, wind speed and radiative cooling. The potential of VIPV-EV to be deployed in 10 major cities was also analyzed. Although sunshine cities such as Phoenix show the high reduction ratio of driving range with 17% due to temperature rise of VIPV modules, populous cities such as Tokyo show low reduction ratio of 9%. It was also shown in this paper that the difference between the driving distance of VIPV-EV driving in the morning and the afternoon is due to PV modules’ radiative cooling. In addition, the importance of heat dissipation of PV modules and the development of high-efficiency PV modules with better temperature coefficients was suggested in order to expand driving range of VIPV-EV. The effects of air-conditioner usage and partial shading in addition to the effects of temperature rise of VIPV modules were suggested as the other power losses of VIPV-EV.

Correlation Analysis of Wind Turbine Temperature Rise and Exergy Efficiency Based on Field-Path Coupling

To solve the problems of large losses and low productivity of permanent magnet synchronous generators used in wind power systems,the field-circuit coupling method is used to accurately solve the electromagnetic field and temperature field of the generator.The loss distribution of the motor is accurately obtained by considering the influence of external circuit characteristics on its internal physical field.By mapping the losses to the corresponding part of the three-dimensional finite element model of the motor,the temperature field is solved,and the global temperature distribution of the generator,considering the influence of end windings,is obtained.By changing the air gap length,permanent magnet thickness,and winding conductivity,the relationship between the loss,temperature rise,and exergy efficiency can be obtained.By optimizing the air gap length,permanent magnet thickness,and winding conductivity,the best configuration and material properties can improve the efficiency of the motor by up to 4%.

Feasibility Research of Using Phase Change Materials to Reduce the Inner Temperature Rise of Mass Concrete

In order to evaluate the feasibility of using phase change materials to reduce the inner temperature rise of mass concrete, the interior temperature of normal concrete specimen under semi-adiabatic curing condition was measured. The effect of embedding phase change material(PCM) and replacing water with suspension of phase change material(SPCM) as cooling fluid were compared in the experiment. The cooling effect and the affecting factors were analyzed and calculated. The research results showed that the peak of inner temperature could be decreased obviously by the method of pre-embeding PCM in concrete, however, this method is only effective in the initial stage of cement hydration process. Besides, the volume of PCM is rather big and the PCM can not be used circularly, which means that this method can only be used under special condition and the feasibility is low. When SPCM was used as cooling fluid, the interior temperature rise of mass concrete was reduced more effectively, and the temperature grads peak around the cooling pipe was also reduced. Besides, both the SPCM consumption amount and the circulation time were decreased, and most important is that the SPCM is recyclable. The technical and economical feasibility of using SPCM to reduce the inner temperature rise of mass concrete is high.

Estimation of Critical Rate of Temperature Rise for Thermal Explosion of First Order Autocatalytic Decomposition Reaction Systems by Using Non-isothermal DSC

A method of estimating the critical rate of temperature rise for the thermal explosion of first order autocatalytic decomposition reaction systems by using non-isothermal DSC is presented. The information was obtained on the increasing rate of temperature for the first order autocatalytic decomposition of nitrocellulose containing 13.86% nitrogen converting into the thermal explosion.

Influence of Particles on the Loading Capacity and the Temperature Rise of Water Film in Ultra-high Speed Hybrid Bearing

Ultra-high speed machining technology enables high efficiency, high precision and high integrity of machined surface. Previous researches of hybrid bearing rarely consider influences of solid particles in lubricant and ultra-high speed of hybrid bearing, which cannot be ignored under the high speed and micro-space conditions of ultra-high speed water-lubricated hybrid bearing. Considering the impact of solid particles in lubricant, turbulence and temperature viscosity effects of lubricant, the influences of particles on pressure distribution, loading capacity and the temperature rise of the lubricant film with four-step-cavity ultra-high speed water-lubricated hybrid bearing are presented in the paper. The results show that loading capacity of the hybrid bearing can be affected by changing the viscosity of the lubricant, and large particles can improve the bearing loading capacity higher. The impact of water film temperature rise produced by solid particles in lubricant is related with particle diameter and minimum film thickness. Compared with the soft particles, hard particles cause the more increasing of water film temperature rise and loading capacity. When the speed of hybrid bearing increases, the impact of solid particles on hybrid bearing becomes increasingly apparent, especially for ultra-high speed water-lubricated hybrid bearing. This research presents influences of solid particles on the loading capacity and the temperature rise of water film in ultra-high speed hybrid bearings, the research conclusions provide a new method to evaluate the influence of solid particles in lubricant of ultra-high speed water-lubricated hybrid bearing, which is important to performance calculation of ultra-high speed hybrid bearings, design of filtration system, and safe operation of ultra-high speed hybrid bearings.

Physical, Psychological, and Social Health Impact of Temperature Rise Due to Urban Heat Island Phenomenon and Its Associated Factors

The Urban Heat Island Effect（UHI）has now become a commonly observed phenomenon worldwide.Indeed,it has become a significant environmental effect of urbanisation.In Malaysia,research results showed that UHI effects are very evident in several cities such as Kuala Lumpur and Putrajaya.UHI effect has long been observed to cause temperature of cities.

The Method for Measuring the Loop Resistance and the Temperature Rise Calculation of GIS Conductor Pole

This paper studies the method for measuring the loop resistance of GIS conductor pole based on the super capacitor producing impulse current up to several thousand amperes. This method overcomes the limitations of conventional diagnostic method. Typical GIS conductor poles are chosen. Based on FEA and lab tests, the effect of different forms of current and contact condition, relationship between the temperature of contact and the loop resistance is researched. In full- scale testing under realistic operating conditions on the new 220 kV GIS using prototype instrumentation a very good sensitivity in an early stage was obtained.

Analysis and Calculation for Heating and Temperature Rise of Magnetic Levitation Device

准确的热分析是磁悬浮系统电磁装置优化设计、防止过热的前提。提出了基于等效热路模型的电磁装置发热及温升计算方法,并与基于＂场＂的仿真分析结果进行比较,验证其正确性。首先,利用ANSYS软件建立电磁装置的瞬态温度场模型,并将装置中动铁心随大轴旋转时与空气产生的风摩擦损耗包含在模型中,通过仿真分析,得到电磁装置温度分布;然后,通过对散热路径的分析建立了电磁装置的等效热路模型,从＂路＂的角度计算出本电磁装置各位置的温升;最后,将基于＂路＂的计算结果与基于＂场＂的仿真结果进行了比较分析,各部分温升误差均在允许范围内,验证了等效热路模型计算电磁装置发热及温升方法的准确性和可行性。在基于＂场＂和＂路＂的两种分析中,均考虑了电阻率随温升的变化,散热分析中均计及了导热系数和对流散热系数随温度的变化。

A THEORETICAL CALCULATION OF TEMPERATURE RISE(TR) IN PIPELINE OF COOL-SUPPLY SYSTEM

In the design of cool-supply system, the temperature rise of cooling water pipeline is usually determined by experience, but not calculated. In gcnacral, the temperature rise is 1℃ for cooling water supply pipes and 0.5℃ for return pipes. The calculated results of TR according to classical approaches of thermodynamics are smaller than the tested data. This paper has analysed the causes that affect the temperature rise in detail. The heat transfer of pipe wall and the pressure drop in pipeline are two main factors. Besides, the paper gives another five factors as follows: 1. The heat radiation from the sun to pipelines; 2. The increased heat transfer due to the water condensation around the outer wall of pipelines; 3. For the underground pipelines, the existing unstable heat transfer; 4. The effects of insulation material as well as the installed quality of insulation layer; 5.The additional cool loss produced by the accessories, such as valves, brace etc. According to the above analysis, the paper

On-line Temperature Rise Measurement of Submersible Motors

Ｏｎ－ｌｉｎｅＴｅｍｐｅｒａｔｕｒｅＲｉｓｅＭｅａｓｕｒｅｍｅｎｔｏｆＳｕｂｍｅｒｓｉｂｌｅＭｏｔｏｒｓ￥（王凤昌）（刘宝廷）（宋黎明）（姜思杰）ＷＡＮＧＦｅｎｇｃｈａｎｇ；ＬＩＵＢａｏｔｉｎｇ；ＳＯＮＧＬｉｍｉｎｇ；ＪＩＡＮＧＳｉｊｉｅ（Ｄｅｐｔ．...

Numerical analysis of temperature rise within 70MPa composite hydrogen vehicle cylinder during fast refueling

The numerical simulation model for predicting fast filling process of 70 MPa type Ⅲ(with metal liner) hydrogen vehicle cylinder was presented,which has considered turbulence,real gas effect and solid heat transfer issues.Through the numerical analysis method,the temperature distributions of the gas within the solid walls were revealed; adiabatic filling was studied to evaluate the heat dissipation during the filling; the influences of various filling conditions on temperature rise were analyzed in detail.Finally,cold filling was proposed to evaluate the effect on temperature rise and SoC(state of charge) within the cylinder.The hydrogen pre-cooling was proved to be an effective solution to reduce maximum temperature and acquire higher SoC during the filling process.

Multi-powder dam concrete with high performance and low adiabatic temperature rise

Based on the fluidity, strength, heat of hydration and loop crack resistance experiment of multi-powder paste, the components and proportion of multi-powder were optimized and the concrete properties were studied. The multi-powder consists of limestone powder, slag, fly ash and moderate heat Portland cement (PMH cement). The results show that the compressive strength of the multi-powder paste and mortar is close to those of PMH cement, fly ash paste and mortar currently used in dam concrete, yet the flexural strength is relatively higher. The multi-powder paste is featured by larger fluidity, lower heat of hydration and delayed cracking time. In comparison, less unit water consumption and cement is used in multi-powder concrete, and under premise of equal mechanical performance, deformation, thermal performance and durability, the adiabatic temperature rise at 28 d is reduced by 2 ℃. In this way, the crack resistance is improved and it is feasible both technically and economically to produce HPC for dam concrete.

A MODIFIED THERMAL VISCOPLASTIC CONSTITUTIVE LAW INVOLVING THE EFFECT OF TEMPERATURE RISE RATE

At high temperature rise rate, the mechanical properties of 10 # steel were determined experimentally in a very wide range of temperature and strain rates. A new constitutive relationship was put forward, which can fit with the experimental results and describe various phenomena observed in our experiments. Meanwhile, some interesting characteristics about the temperature rise rate, strain and strain rate hardening and thermal softening are also shown in this paper. Finally, the reliability of the constitutive law and the correctness of the constitutive parameters were verified by comparing the calculation results with the experimental data.

Analysis of Temperature Rise in High-Speed Permanent Magnet Synchronous Traction Motors by Coupling the Equivalent Thermal Circuit Method and Computational Fluid Dynamics

To solve the problem of temperature rise caused by the high power density of high-speed permanent magnet synchronous traction motors,the temperature rise of various components in the motor is analyzed by coupling the equivalent thermal circuit method and computational fluid dynamics.Also,a cooling strategy is proposed to solve the problem of temperature rise,which is expected to prolong the service life of these devices.First,the theoretical bases of the approaches used to study heat transfer and fluid mechanics are discussed,then the fluid flow for the considered motor is analyzed,and the equivalent thermal circuit method is introduced for the calculation of the temperature rise.Finally,the stator,rotor loss,motor temperature rise,and the proposed cooling method are also explored through experiments.According to the results,the stator temperature at 50,000 r/min and 60,000 r/min at no-load operation is 68℃ and 76℃,respectively.By monitoring the temperature of the air outlets inside and outside the motor at different speeds,it is also found that the motor reaches a stable temperature rise after 65 min of operation.Coupling of the thermal circuit method and computational fluid dynamics is a strategy that can provide the average temperature rise of each component and can also comprehensively calculate the temperature of each local point.We conclude that a hybrid cooling strategy based on axial air cooling of the inner air duct of the motor and water cooling of the stator can meet the design requirements for the ventilation and cooling of this type of motors.

Three-Dimensional Mantle Flow and Temperature Structure Beneath the Shatsky Rise Ridge-Ridge-Ridge Triple Junction

The Shatsky Rise ridge-ridge-ridge triple junction is an ancient triple junction in the Western Pacific Ocean whose initial geodynamic process is poorly understood and can only be inferred based on indirect geological and geophysical constraints.In this paper,we present three-dimensional numerical models that simulate the Shatsky Rise triple junction and calculate its coupled mantle flow and temperature structure.The mantle flow velocity field shows several distinctive features:1)stronger mantle upwelling closer to the ridge axis and triple junction;2)greater upwelling velocity at the faster-spreading ridges;and 3)the most significant increase in upwelling velocity for the slowest-spreading ridge toward the triple junction.The calculated mantle temperature field also reveals distinctive characteristics:1)sharp increases in the mantle temperature with depth and increases toward the spreading ridges and triple junction;2)the faster-spreading ridges are associated with higher temperatures at depth and identical distances from the triple junction;and 3)the slowest-spreading ridge shows the greatest increase in the along-ridge-axis temperature toward the triple junction.Compared to many present-day triple junctions with slower spreading rates,the along-ridge-axis velocity and thermal fields of the Shatsky Rise are more altered due to the presence of the triple junction.

Improving Local Temperature Rise in Rotational Incremental Sheet Forming Process by Modifying Forming Parameters Using Response Surface Method

In rotational incremental sheet forming( RISF) process,the friction heating of rotational tool could lead to local temperature rise of the sheet and cause the improvement of sheet's formability.Lightweight metal,such as magnesium alloy,could be deformed by RISF without additional heating. The objective of this study is to investigate the effects of forming parameters,namely,tool rotational speed,feed-rate,step size and wall angle,on the local temperature rise. Using response surface methodology and central composite design( CCD) experimental design,the significance,sequence of parameters and regression models would be analyzed with AZ31 B as the experimental material,and 3D response surface plots would be shown. Combined with actual processing conditions,the measures to improve the local temperature rise by modifying each parameter would be discussed in the end. The results showed that hierarchy of the parameters with respect to the significance of their effects on the local temperature at the side wall was: feed-rate,step size,and rotational speed,while at the bottom it was: feed-rate,step size,wall angle, and rotational speed, and no significant interaction appeared. It was found that the most significant parameter was not rotational speed,but feed-rate,followed by step size,for both test positions. In addition, the local temperature would increase by elevating step size,wall angle,rotating rate,and bringing down of feed-rate.

Temperature Rise Calculation and Velocity Planning of Permanent Magnet Linear Synchronous Motor under Trapezoidal Speed

For permanent magnet linear synchronous motor(PMLSM) working at trapezoidal speed for long time, high thrust brings high temperature rise, while low thrust limits dynamic performance. Thus, it is crucial to find a balance between temperature rise and dynamic performance. In this paper, a velocity planning model of the PMLSM at trapezoidal speed based on electromagnetic-fluid-thermal(EFT) field is proposed to obtain the optimal dynamic performance under temperature limitation. In this model, the winding loss is calculated considering the acceleration and deceleration time. The loss model is indirectly verified by the temperature rise experiment of an annular winding sample. The actual working conditions of the PMLSM are simulated by dynamic grid technology to research the influence of acceleration and deceleration on fluid flow in the air gap, and the variation rule of the thermal boundary condition is analyzed. Combined with the above conditions, the temperature rise of a coreless PMLSM(CPMLSM) under the rated working condition is calculated and analyzed in detail. Through this method and several iterations, the optimal dynamic performance under the temperature limitation is achieved. The result is verified by a comparison between simulation and prototype tests, which can help improve the dynamic performance.

ExperimentonPerformanceofLow-TemperatureExhaustSteamReclamation

针对不同的喉嘴距、面积比，实验研究了不同的进水压力、进水温度和出水压力对低温乏汽回收利用装置性能的影响规律．发现在进水压力为0．14～O．50MPa、进水温度为23～60℃、出水压力为0．096-0．110MPa，以及4种喉嘴距、3种面积比的实验条件范围内，随着喉嘴距和面积比的增加，加热温升和流量比先增大后减小，得到最佳归一化喉嘴距L=4．50，以及最佳面积比m=6．25，使得加热温升和流量比最大．同时，加热温升和流量比均随着进水压力和进水温度的增加而减小，当出水压力升高时，装置性能变差，加热温升和流量比均减小．

A Model for Temperature Infl uence on Concrete Hydration Exothermic Rate (Part one: Theory and Experiment)

Recent achievements in concrete hydration exothermic models based on Arrhenius equation have improved computation accuracy for mass concrete temperature field. But the properties of the activation energy and the gas constant （Ea/R） have not been well studied yet. From the latest experiments it is shown that Ea/R obviously changes with the hydration degree without fixed form. In this paper, the relationship between hydration degree and Ea/R is studied and a new hydration exothermic model is proposed. With those achievements, the mass concrete temperature field with arbitrary boundary condition can be calculated more precisely.