Application and improvement of wavelet packet de-noising in satellite transponder

The satellite transponder is a widely used module in satellite missions, and the most concerned issue is to reduce the noise of the transferred signal. Otherwise, the telemetry signal will be polluted by the noise contained in the transferred signal, and the additional power will be consumed. Therefore, a method based on wavelet packet de-noising （WPD） is introduced. Compared with other techniques, there are two features making WPD more suit- able to be applied to satellite transponders： one is the capability to deal with time-varying signals without any priori information of the input signals; the other is the capability to reduce the noise in band, even if the noise overlaps with signals in the frequency domain, which provides a great de-noising performance especially for wideband signals. Besides, an oscillation detector and an av- eraging filter are added to decrease the partial oscillation caused by the thresholding process of WPD. Simulation results show that the proposed algorithm can reduce more noises and make less distortions of the signals than other techniques. In addition, up to 12 dB additional power consumption can be reduced at -10 dB signal-to-noise ratio （SNR）.

Reduction of ultrasonic echo noise based on improved wavelet threshold de-noising algorithm for friction welding

In the ultrasonic detection of defects in friction welded joints, it is difficult to exactly detect some weak bonding defects because of the noise pollution. This paper proposed an improved threshold function based on the multi-resolution analysis wavelet threshold de-noising method which was put forward by Donoho and Johnstone, and applied this method in the de-noising of the defective signals. This threshold function overcomes the discontinuous shortcoming of the hard-threshold function and the disadvantage of soft threshold function which causes an invariable deviation between the estimated wavelet coeffwients and the decomposed wavelet coefficients. The improved threshold function is of simple expression and convenient for calculation. The actual test results of defect noise signal show that this improved method can get less mean square error （ MSE ） and higher signal-to-noise ratio of reconstructed signals than those calculated from hard threshold and soft threshold methods. The improved threshold function has excellent de-noising effect.

Application of Wavelet Packet De-noising in Time-Frequency Analysis of the Local Wave Method

The local wave method is a very good time-frequency method for nonstationaryvibration signal analysis. But the interfering noise has a big influence on the accuracy oftime-frequency analysis. The wavelet packet de-noising method can eliminate the interference ofnoise and improve the signal-noise-ratio. This paper uses the local wave method to decompose thede-noising signal and perform a time-frequency analysis. We can get better characteristics. Finally,an example of wavelet packet de-noising and a local wave time-frequency spectrum application ofdiesel engine surface vibration signal is put forward.

A continuous differentiable wavelet threshold function for speech enhancement

Enhanced speech based on the traditional wavelet threshold function had auditory oscillation distortion and the low signal-to-noise ratio (SNR). In order to solve these problems, a new continuous differentiable threshold function for speech enhancement was presented. Firstly, the function adopted narrow threshold areas, preserved the smaller signal speech, and improved the speech quality; secondly, based on the properties of the continuous differentiable and non-fixed deviation, each area function was attained gradually by using the method of mathematical derivation. It ensured that enhanced speech was continuous and smooth; it removed the auditory oscillation distortion; finally, combined with the Bark wavelet packets, it further improved human auditory perception. Experimental results show that the segmental SNR and PESQ (perceptual evaluation of speech quality) of the enhanced speech using this method increase effectively, compared with the existing speech enhancement algorithms based on wavelet threshold.

Denoising of an Image Using Discrete Stationary Wavelet Transform and Various Thresholding Techniques

Image denoising has remained a fundamental problem in the field of image processing. With Wavelet transforms, various algorithms for denoising in wavelet domain were introduced. Wavelets gave a superior performance in image denoising due to its properties such as multi-resolution. The problem of estimating an image that is corrupted by Additive White Gaussian Noise has been of interest for practical and theoretical reasons. Non-linear methods especially those based on wavelets have become popular due to its advantages over linear methods. Here I applied non-linear thresholding techniques in wavelet domain such as hard and soft thresholding, wavelet shrinkages such as Visu-shrink (non-adaptive) and SURE, Bayes and Normal Shrink (adaptive), using Discrete Stationary Wavelet Transform (DSWT) for different wavelets, at different levels, to denoise an image and determine the best one out of them. Performance of denoising algorithm is measured using quantitative performance measures such as Signal-to-Noise Ratio (SNR) and Mean Square Error (MSE) for various thresholding techniques.

A real-time 5/3 lifting wavelet HD-video de-noising system based on FPGA

In accordance with the application requirements of high definition(HD) video surveillance systems,a real-time 5/3 lifting wavelet HD-video de-noising system is proposed with frame rate conversion(FRC) based on a field-programmable gate array(FPGA),which uses a 3-level pipeline paralleled 5/3 lifting wavelet transformation and reconstruction structure,as well as a fast BayesS hrink adaptive threshold filtering module.The proposed system demonstrates de-noising performance,while also balancing system resources and achieving real-time processing.The experiments show that the proposed system's maximum operating frequency(through logic synthesis and layout using Quartus 13.1 software) can reach 178 MHz,based on the Altera Company's Stratix III EP3SE80 series FPGA.The proposed system can also satisfy real-time de-noising requirements of 1920 × 1080 at60 fps HD-video sources,while also significantly improving the peak signal to noise rate of the denoising images.Compared with similar systems,the system has the advantages of high operating frequency,and the ability to support multiple source formats for real-time processing.

Implementation of GPR Signals De-Noising Based on DSP

An important issue of ground-penetrating radar （GPR） signals analysis is de-noising thai is the guarantee of acquiring good detecting effect. The paper illustrates a successful application of digital single processor （DSP） based on wavelet shrinkage algorithm. In order to realize real-time GPP, signals analysis, some key issues are discussed such as the realization of fast wavelet transformation, the selection of CPU chip and the optimization of data movement. Experimenial results show that the DSP based application not only basically meets the real-time requirement of GPP, signals analysis, but also assures the quality of the GPR signals analysis.

基于增强多头注意力机制的Optuna-BiGRU测井岩性识别

测井岩性识别是油气勘探开发中至关重要的内容。针对现有算法模型在处理测井曲线数据时,无法有效捕获曲线内部深层关联和深度方向关系、拟合能力较弱、难以准确提取关键特征、噪声干扰以及模型超参数调优过程复杂困难等问题,提出了一种通过Optuna超参数优化双向门循环单元(Optuna-BiGRU)结合增强多头注意力机制(EMHA)的测井岩性识别模型——Optuna-BiGRU-EMHA模型。该模型引入残差机制和层归一化以改进多头注意力机制模块,并结合双向门循环单元(BiGRU)解决了处理测井数据时的问题,同时使用Optuna超参数优化框架和小波包自适应阈值方法分别解决了超参数调优和噪声干扰问题。首先通过交会图分析和敏感性箱线图分析选取自然伽马、深感应电阻率、中子-密度孔隙度、平均中子-密度孔隙度和岩性密度5个特征参数的测井数据,通过小波包自适应阈值方法对数据进行去噪,并将测井数据分割成数据块,然后利用Optuna框架优化BiGRU-EMHA模型超参数,最后通过实验对比K-近邻算法(KNN)、随机森林(RF)、极端梯度提升算法(XGBoost)、长短期记忆(LSTM)神经网络、BiGRU、双向长短期记忆(BiLSTM)神经网络、BiGRU-MHA、Optuna-BiGRU-EMHA等8种模型在测井岩性识别中的精度。结果表明:Optuna-BiGRU-EMHA模型识别准确率达到80%,相对于传统机器学习模型和深度学习模型,综合岩性识别准确率分别提高15.94%~23.14%和3.93%~15.94%,该模型为常规测井岩性识别提供了坚实的理论支持。

联合小波-频域变换的自适应能量检测

针对传统能量检测方法在频谱感知领域中极易受低信噪比环境干扰,忽视可用频谱的定位亦会影响频谱状态的判别结果,提出了一种联合小波-频域变换的自适应能量检测方法,旨在提高能量检测的噪声灵敏度和判别精确度。通过离散小波包变换对信号进行分解并计算子带能量;结合能量范数降低自适应阈值的计算复杂度,以便与子带能量比较;采用快速傅里叶变换定位可用频谱范围。对该方法进行模拟仿真,探究自适应阈值与不同性能参数之间的变化关系。仿真结果表明,该方法具有良好的环境适配性与系统稳定性,且在不同信噪比环境下的检测误差更小。此外,对子带信号进行频域分析以实现归一化频率范围的重新排序,进一步提高了频谱感知的准确度。

基于EEMD-WPT的温室环境数据优化处理研究

【目的】解决温室系统中的数据采集传感器容易受到多种环境因素的干扰,从而导致数据中存在噪声的问题。【方法】提出一种集合经验模态分解(Ensemble empirical mode decomposition,EEMD)与小波包自适应阈值(Wavelet packet adaptive threshold,WPT)算法联合的数据降噪处理方法,并采用卡尔曼滤波与自适应加权平均算法对降噪后的数据进行融合。【结果】将EEMD-WPT算法应用于含噪温、湿度数据的降噪处理,相较于降噪前的数据,信噪比提升了73.08%。该算法相较于传统WPT算法具有更好的降噪效果,处理后的数据信噪比提升了40.31%,均方根误差降低了84.75%。【结论】该算法能解决数据跳动、冗余和丢失等问题,并为温室控制系统提供了有效的参数,具有较大的实际应用价值。

参数优化VMD结合改进小波包阈值的去噪方法

针对轴承信号故障特征容易被噪声淹没的问题,提出一种参数优化变分模态分解结合改进小波包阈值的去噪方法。首先,通过变分模态分解(Variational Mode Decomposition,VMD)结合改进粒子群算法(Improve Particle Swarm Optimization,IPSO)将含噪信号分解为若干本征模态分量(Intrinsic Mode Function,IMF)。以最大相关系数-相关峭度为准则,把IMF分为高值分量(High-value Intrinsic Mode Function,HIMF)和低值分量(Low-value Intrinsic Mode Function,LIMF)。再对LIMF进行改进小波包(Improved Wavelet Packet,IWP)阈值去噪。最后对重构信号进行包络解调,提取轴承故障特征频率,完成故障诊断。实验结果表明,该方法不仅能够避免“过扼杀”现象,并且可以得到信噪比更高的去噪信号。

基于CEEMDAN和小波包分解的闸门振动信号降噪研究

针对闸门监测振动信号去噪问题,提出基于CEEMDAN(经验模态分解)和小波包分解的闸门振动信号降噪算法,通过采用CEEMDAN和小波包分解方法进行信号去噪,可以有效处理水电站泄洪闸门振动信号中受到的外部干扰。CEEMDAN方法能够将信号分解成多个本征模态函数(IMF),每个IMF代表不同频率的振动成分,使得外部干扰和真实信号成分可以分离。随后,小波包分解能够将每个IMF进一步分解成不同尺度和频率的子频带,这有助于更准确地定位和分离干扰成分。对每个子频带应用阈值去噪技术,可以有效去除噪声,保留真实信号。由测试结果可知,该算法能很好地剔除闸门振动信号中的无用噪声,有效提高闸门振动信号的准确性。

基于改进小波包能量熵和阈值自适应的切削颤振在线监测

颤振是影响机床加工质量的重要原因之一,传统的颤振监测算法对颤振孕育阶段的感知灵敏度低,且监测阈值的设定不具备泛化性和实时性,针对该问题提出了一种能够自适应地识别早期颤振的在线监测方法。首先使用改进的小波包能量熵算法(IWPEE)提取颤振特征,在提高识别精度和鲁棒性的同时降低了计算量。其次基于改进的拉依达准则确定颤振监测阈值,使系统能够根据不同的加工条件自适应地计算颤振监测阈值。然后根据实际加工监测需求开发高效颤振在线监测软件,并且通过仿真信号和切削试验验证了本文所提算法的有效性。结果表明,IWPEE算法相较于传统熵值判定法,识别灵敏度提高了360%,改进的拉依达准则能自适应地确定阈值并成功在颤振孕育阶段将其监测出来,相较于传统阈值算法在阈值稳定性和适应性上有显著提升。

基于RLMD与SSA-BP的采煤机工况模式识别

针对采煤机工作环境恶劣、振动噪声大、故障率高等特点,提出了一种基于鲁棒性局部均值分解(RLMD)结合麻雀搜索算法(SSA)优化BP神经网络的采煤机工况模式识别方法。首先,对不同工况下采集到的振动数据进行小波包阈值降噪,之后进行RLMD分解,选取相关系数大于0.1的P_(F)分量对信号进行重构,选取排列熵、样本熵、模糊熵作为每条数据的特征集,最后输入到SSA-BP神经网络中进行工况模式识别,并与PSO-BP、GA-BP的识别结果进行对比,仿真结果表明:该方法的迭代次数最少,同时准确率最高,可达98.33%;最后也对比了数据预处理前后的准确率,证实了所提及的小波包阈值降噪结合RLMD的双重降噪方法的有效性。

基于多频带多特征融合的配电网单相接地故障选段方法

针对现有配电网单相接地故障选段方法存在的通信负担重、阈值设置困难及故障特征量单一等问题,提出一种基于多频带多特征融合的配电网单相接地故障选段方法。首先,利用小波包变换分别对故障后首半个工频周期的零序电压导数和零序电流进行分解和重构,得到原始波形的不同频带分量。其次,根据不同频带分量间的极性关系分别引入伏安特性特征向量与零序功率累加和作为故障特征。最后,筛选特征频带并构造基于特征频带与故障特征融合的选段判据。仿真实验及现场数据验证结果表明,所提方法能够有效实现单相接地故障免阈值就地选段。

基于小波包变换的电机测试信号去噪处理

作为一种日益获得广泛应用的信号处理新技术 ,小波分析具有良好的时频局域化特性 ,适应于时变和瞬变信号的分析。针对电机起动过程中的噪声干扰信号 ,提出了基于小波包变换的浮动阈值去噪算法。实验结果表明 。

基于小波包的图像去噪方法

本文在分析了信号与噪声的不同小波特性的基础上 ,提出了一种基于小波包的去噪方法 。

基于时延相关及小波包系数熵阈值的增强型共振解调方法

针对滚动轴承等旋转机械早期微弱损伤性故障,提出一种基于时延相关及小波包系数熵阈值的增强型共振解调方法,以解决传统共振解调技术中共振带难以确定的问题。该方法对原始故障信号做时延相关预处理,然后进行小波包分解,求出各叶结点系数香农熵,依据熵值谱图,设定有效阈值来取舍叶结点系数,重构信号并做频谱分析,有效确定并提取故障信号共振带,对共振带进行包络解调分析,有效提取出机械设备早期微弱损伤性故障的冲击特征。滚动轴承试验数据分析结果表明该方法的可行性和有效性。

基于小波包变换和数学形态学结合的光谱去噪方法研究

对反射光谱数据进行去噪是提高光谱信息准确度的前提。传统时域平滑和频域去噪方法存在诸多缺点,本文首次将广义形态滤波方法用于可见近红外光谱的去噪处理,并提出基于小波包变换和数学形态学结合的光谱去噪方法。使用USGS光谱库中的植被光谱进行实验,采用信噪比(SNR)、均方误差根(RMSE)、波形相似度(NCC)和平滑度(SR)四个指标来评估去噪效果。结果表明,小波包最佳基阈值法和广义形态滤波法都能较好地保持波形和平滑度,广义形态滤波法能较好地消除幅值较大的随机噪声,但其对连续随机噪声中幅值较小的噪声成分不能有效消除;而小波包最佳基阈值法不能有效消除幅值较大的噪声成分;二者结合的方法组合了这两者的优点,使得幅值较大、较小的噪声成分都能较好地消除,同时还提高了相似度和平滑度指标,充分表明小波包最佳基阈值与广义形态滤波结合的方法是一种更好的可见光近红外光谱去噪方法。

机床主轴径向误差运动在线检测与信号处理

在机床加工工件时,实时测量机床主轴的径向运动误差。测量对象是在该机床上加工的圆柱形工件,而不是通常所使用的标准棒。采用误差分离技术将工件的形状误差从所测信号中分离出来,实现在线测量主轴的径向误差运动。并采用基于自适应阈值的小波包算法去除加工时存在的噪声。同时,从谐波抑制特性和总体频域特性两个方面分析了测量系统频域特征。