Thermo-hydro-poro-mechanical responses of a reservoir-induced landslide tracked by high-resolution fiber optic sensing nerves

Thermo-poro-mechanical responses along sliding zone/surface have been extensively studied.However,it has not been recognized that the potential contribution of other crucial engineering geological interfaces beyond the slip surface to progressive failure.Here,we aim to investigate the subsurface multiphysics of reservoir landslides under two extreme hydrologic conditions(i.e.wet and dry),particularly within sliding masses.Based on ultra-weak fiber Bragg grating(UWFBG)technology,we employ specialpurpose fiber optic sensing cables that can be implanted into boreholes as“nerves of the Earth”to collect data on soil temperature,water content,pore water pressure,and strain.The Xinpu landslide in the middle reach of the Three Gorges Reservoir Area in China was selected as a case study to establish a paradigm for in situ thermo-hydro-poro-mechanical monitoring.These UWFBG-based sensing cables were vertically buried in a 31 m-deep borehole at the foot of the landslide,with a resolution of 1 m except for the pressure sensor.We reported field measurements covering the period 2021 and 2022 and produced the spatiotemporal profiles throughout the borehole.Results show that wet years are more likely to motivate landslide motions than dry years.The annual thermally active layer of the landslide has a critical depth of roughly 9 m and might move downward in warmer years.The dynamic groundwater table is located at depths of 9e15 m,where the peaked strain undergoes a periodical response of leap and withdrawal to annual hydrometeorological cycles.These interface behaviors may support the interpretation of the contribution of reservoir regulation to slope stability,allowing us to correlate them to local damage events and potential global destabilization.This paper also offers a natural framework for interpreting thermo-hydro-poro-mechanical signatures from creeping reservoir bank slopes,which may form the basis for a landslide monitoring and early warning system.

Monitoring shear deformation of sliding zone via fiber Bragg grating and particle image velocimetry

Monitoring shear deformation of sliding zones is of great significance for understanding the landslide evolution mechanism,in which fiber optic strain sensing has shown great potential.However,the cor-relation between strain measurements of quasi-distributed fiber Bragg grating(FBG)sensing arrays and shear displacements of surrounding soil remains elusive.In this study,a direct shear model test was conducted to simulate the shear deformation of sliding zones,in which the soil internal deformation was captured using FBG strain sensors and the soil surface deformation was measured by particle image velocimetry(PIV).The test results show that there were two main slip surfaces and two secondary ones,developing a spindle-shaped shear band in the soil.The formation of the shear band was successfully captured by FBG sensors.A sinusoidal model was proposed to describe the fiber optic cable deformation behavior.On this basis,the shear displacements and shear band widths were calculated by using strain measurements.This work provides important insight into the deduction of soil shear deformation using soil-embedded FBG strain sensors.

Multiwavelength Actively Mode-locked Fiber Laser with a Double-ring Configuration and Integrated Cascaded Sampled Fiber Bragg Gratings

A modified multiwavelength actively mode-locked fiber ring laser is proposed and experimentally demonstrated. In this kind of laser, stable multiwavelengths lasing is achieved by integrating cascaded sampled fiber Bragg gratings(SFBGs) into the laser cavity. To implement actively mode-locking technique, a double-ring cavity configuration is used to assure that the cavity lengths for all wavelengths lasing are identical. Thus, simultaneous mode locking of all wavelengths has been successfully achieved by using the same mode-locking signal.

Irradiation effect on strain sensitivity coefficient of strain sensing fiber Bragg gratings

The effect of irradiation on the strain sensitivity coefficient of strain sensing fiber Bragg gratings （FBGs） has been investigated through experiments. FBGs were fabricated in single mode fibers with 3 tool% Ge-concentration in the core and with a H2-1oading treatment. In experiments, the FBGs were subjected to y-radiation exposures using a Co6~ source at a dose-rate of 25 Gy/min up to a total dose of 10.5 kGy. The GeO defect in fiber absorbs photons to form a GeE＇ defect; the interaction with H2 is a probable reason for the y-radiation sensitivity of gratings written in hydrogen loaded fibres, The effect mechanism of radiation on the strain sensitivity coefficient is similar to that of radiation on the temperature sensitivity coefficient. Radiation affects the effective index neff, which results in the change of the thermo-optic coefficient and the strain-optic coefficient. Irradiation can change the strain sensitivity coefficient of FBGs by 1.48%-2.71%, as well as changing the Bragg wavelength shift （BWS） by 22 pm-25 pm under a total dose of 10.5 kGy. Our research demonstrates that the effect of irradiation on the strain sensitivity coefficient of FBG is small and that strain sensing FBGs can work well in the radiation environment.

Spectral Beam Combining of Fiber Lasers by Using Reflecting Volume Bragg Gratings

By employing three reflecting volume Bragg gratings, a near-infrared 4-channel spectral-beam-combining system is demonstrated to present 720 W combined power with a combining efficiency of 94.7%. The combined laser beam is near-diffraction-limited with a beam factor M^2-1.54. During this 4-channel beam-combining process, no special active cooling measures are used to evaluate the volume Bragg gratings as combining elements are under the higher power laser operation. Thermal expansion and period distortion are verified in a 2 k W 2-channel beam-combining process, and the heat issue in the transmission case is found to be more remarkable than that in the diffraction e-se. Transmitted and diffracted beams experience wave-front aberrations with different degrees, thus leading to distinct beam deterioration.

Advances in femtosecond laser direct writing of fiber Bragg gratings in multicore fibers:technology,sensor and laser applications

In this article,we review recent advances in the technology of writing fiber Bragg gratings(FBGs)in selected cores of multicore fibers(MCFs)by using femtosecond laser pulses.The writing technology of such a key element as the FBG opens up wide opportunities for the creation of next generation fiber lasers and sensors based on MCFs.The advantages of the technology are shown by using the examples of 3D shape sensors,acoustic emission sensors with spatially multiplexed channels,as well as multicore fiber Raman lasers.

Fabrication of long-period fiber gratings by CO_2 laser in fiber under tension

We demonstrate experimentally fabrication of CO2 laser written long-period fiber gratings （LPFGs） in single-mode fiber （SMF） under tension. New transmission dips can be generated due to the frozen-in stress in the fiber under tension. Dynamics analysis of laser writing process is performed to study the mechanism of the grating inscription. Experimental results show that the wavelength shift of new generated resonance dips can shift towards the longer or shorter wavelength with the increase of laser scanning cycles for gratings with different pitches.

Engineering approach to in-situ bridge health monitoring with fiber bragg gratings

In this presentation the feasibility and capability of fiber Bragg gratings (FBG) employed in bridge health monitoring are demonstrated on a real bridge. FBG’s wavelength shift depending on strain variance has been tested. The technique of FBG installation on bridges has been developed. 12 FBG strain sensors and 3 temperature sensors have been successfully embedded in the prestressed concrete box girder during the construction of Heilongjiang Hulan River Bridge. The prestressing tension process and quasi-static loading process of the girder were monitored with those sensors before it was installed onto the bridge. After the bridge was completed, the FBG sensors embedded have been utilized to monitor the strain shift of the beam under quasi-static load, traffic load and temperature. The results show that the traffic fluxes, possible fatigue damage and deflection of the bridge can be revealed conveniently through strain measurements with these FBG sensors, which provide key information for structural health diagnosis. The fact that the FBG strain sensors have withstood the ordeal of harsh construction process and lasted for more than one year proves that their durability and stability can satisfy the requirements for bridge health monitoring. It is also shown that the FBG strain sensor is more adaptive to long-term structural health monitoring than the electric resistance strain gauge.

Magneto-Optic Fiber Bragg Gratings with Application to High-Resolution Magnetic Field Sensors

Magneto-optic fiber Bragg gratings （MFBG） based on magneto-optic materials have a lot of potential applications for sensing and optical signal processing. The transmission and reflection spectra of guided optical waves in the MFBG are investigated. According to the sensitivity of MFBG spectral lines to the magneto-optic coupling intensity varying with applied magnetic field, a novel magnetic field sensor of high-resolution up to 0.01 nm/（kA/m） is predicted.

Hollow and filled fiber bragg gratings in nano-bore optical fibers

To combine the technical functions and advantages of solid-core fiber Bragg gratings(FBGs) and hollow-core optical fibers(HCFs), the hollow and filled FBGs in nano-bore optical fibers(NBFs) with nano-bore in the GeO2-doped core are proposed.The fundamental mode field, effective mode index, and confinement loss of NBF with 50 nm–7 μm-diameter hollow and filled nano-bore are numerically investigated by the finite element method.The reflected spectra of FBGs in NBFs are obtained by the transmission matrix method.The hollow FBGs in NBFs can be acheived with ~5% power fraction in the bore and the ~0.9 reflectivity when bore diameter is less than 3 μm.The filled FBGs can be realized with^1% power fraction and 0.98 reflectivity with different fillings including o-xylene, trichloroethylene, and chloroform for 800-nm bore diameter.The feasibility of the index sensing by our proposed NBF FBG is also analyzed and discussed.The experimental fabrication of hollow and filled FBGs are discussed and can be achieved by current techniques.The aim of this work is to establish a principle prototype for investigating the HCFs and solid-core FBGs-based fiber-optic platforms,which are useful for applications such as the simultaneous chemical and physical sensing at the same position.

UV-Inscribed Optical Fiber Gratings in Mid-IR Range and Their Laser Applications

We have UV-inscribed fiber Bragg gratings （FBGs）, long-period gratings （LPGs） and tilted fiber gratings （TFGs） into mid-IR 2μm range using three common optical fiber grating fabrication techniques （two-beam holographic, phase mask and point-by-point）. The fabricated FBGs have been evaluated for thermal and strain response. It has been revealed that the FBG devices with responses in mid-IR range are much more sensitive to temperature than that in near-IR range. To explore the unique cladding mode coupling function, we have investigated the thermal and refractive index sensitivities of LPGs and identified that the coupled cladding modes in mid-IR range are also much more sensitive to temperature and surrounding medium refractive index change. The 45° tilted fiber gratings （45°-TFGs） as polarizing devices in mid-IR have been investigated for their polarization extinction characteristics. As efficient reflection filters and in-cavity polarizers, the mid-IR FBGs and 45°-TFGs have been employed in fiber laser cavity to realize multi-wavelength 2μm Tm-doped CW and mode locked fiber lasers, respectively.

Experimental investigation of pre-irradiation effect on radiation sensitivity of temperature sensing fiber Bragg gratings

The effect of pre-irradiation on radiation sensitivity of fiber Bragg gratings （FBGs） is verified experimentally. FBGs are fabricated in photosensitive optical fibers and single mode fibers with Ce-concentration in a range from 3 mol% to 23.37 mol% in the core. In experiments, the FBGs are subjected to twice v-radiation exposures to a Co^60 source at a dose-rate of 0.1 Gy/s up to a total dose of 50 kGy. Pre-irradiation treatment can reduce the temperature sensitivity variation of FBGs by 18.12%-35.91%, as well as Bragg wavelength shift （BWS） by 8%-27.08 %. Our research demonstrates that pre-irradiation treatment is a feasible method to improve the radiation tolerance of FBGs.

A Novel Method for the Design of Fiber Gratings

A new weighting technique compatible with phase mask technique and point by point technique is proposed. The design method allows precise weighting of the fiber grating using controlled interference of reflected waves. Based upon the new position weighting method, complex shape of fiber grating spectra can be acquired effectively .

A simulation program for analysing fiber optic Bragg gratings

ＡｓｉｍｕｌａｔｉｏｎｐｒｏｇｒａｍｆｏｒａｎａｌｙｓｉｎｇｆｉｂｅｒｏｐｔｉｃＢｒａｇｇｇｒａｔｉｎｇｓＰｅｔｅｒＫＣＣｈａｎ，Ｗ．Ｄｕ，Ｗ．Ｊｉｎ，Ｍ．Ｓ．Ｄｅｍｏｋａｎ（Ｄｅｐｔ．ｏｆＥｌｅｃｔｒ．Ｅｎｇ．，ＨｏｎｇＫｏｎｇＰｏｌｙｔｅｃｈｎｉ...

Convention of Optical Vortices in Two-Helix Long-Period Fiber Gratings

An effective method to fabricate two-helix long-period fiber gratings （TH-LFGs） is presented. Based on the coupling mode theory, the conversion of optical vortices （OVs） in TH-LFGs are analyzed in detail. The conversions of OVs with different topological charges： 0 → ±2 and 1 → 3 are simulated as three examples and the conversion efficiency higher than 98% can be realized.

Tunable Super-Structured Fiber Bragg Gratings with Perfect Sequences Based on m-Sequence

Recently, a tunable fiber Bragg grating(FBG) was developed by using stress-responsive colloidal crystals. In this paper, we have simulated the application of these nanoparticles into the super-structured fiber Bragg grating(SSFBG) written with perfect sequences derived from a short maximal-length sequence. A tunable SSFBG will be available to overcome the prohibitive temperature variation of the optical codecs. Nevertheless,we presented a method to implement coherent time spreading optical code-division multiple-access(OCDMA) where a unique code(or perfect sequence) can be reused and mixed with different wavelengths to obtain a tunable wavelength-division multiplexing(WDM)system. In order to maximize the binary throughput, we have selected a unique short maximal-length sequence composed of 7 chips that can be tuned with 7 different optical wavelengths. We found thousands of different tunable combinations that presented power contrast ratios(P/C) higher than 12 dB. When a WDM-OCDMA system used 2 different combinations simultaneously, the perfect binary detection with error correction codes was achieved successfully. The tunable SSFBG with colloidal crystals will be a simple and good alternative choice for fiber-to-the-home(FTTH) communications.

Review of Turn around Point Long Period Fiber Gratings

Long period fiber gratings are emerging as a potential candidate in the list of surrounding refractive index optical fiber sensors. Their sensitivity can be enhanced greatly if the grating period, fiber dimensions and surrounding refractive index are optimized in a way to operate at a point called turn around point on phase matching curves of these gratings. Turn around point LPFGs are well known for their ultrahigh sensitivity to external parameters. Potential of operating LPFG at or near turn around point has been investigated by many researchers in various applications including physical parameter sensing, adulteration detection, radiation dose, etc. Since TAP LPFGs are in investigation phase therefore a lot of rigorous & efficient work in finding techniques for optimizing their potential as sensor in chemical, biochemical, structural health monitoring is still to be carried out. A brief review of work carried out in this domain till now is presented here and key findings from literature review are highlighted.

In-fiber photoelectric device based on graphene-coated tilted fiber grating

Graphene and related two-dimensional materials have attracted great research interests due to prominently optical and electrical properties and flexibility in integration with versatile photonic structures.Here,we report an in-fiber photoelec-tric device by wrapping a few-layer graphene and bonding a pair of electrodes onto a tilted fiber Bragg grating(TFBG)for photoelectric and electric-induced thermo-optic conversions.The transmitted spectrum from this device consists of a dense comb of narrowband resonances that provides an observable window to sense the photocurrent and the electrical injection in the graphene layer.The device has a wavelength-sensitive photoresponse with responsivity up to 11.4 A/W,allowing the spectrum analysis by real-time monitoring of photocurrent evolution.Based on the thermal-optic effect of electrical injection,the graphene layer is energized to produce a global red-shift of the transmission spectrum of the TF-BG,with a high sensitivity approaching 2.167×10^(4)nm/A^(2).The in-fiber photoelectric device,therefore as a powerful tool,could be widely available as off-the-shelf product for photodetection,spectrometer and current sensor.

Power Tapping Function in Near Infra-Red Region Based on 45°Tilted Fiber Gratings

We report an efficient power tapping device working in near infra-red (800 nm) wavelength region based on UV-in- scribed 45° tilted fiber grating (45°-TFG) structure. Five 45°-TFGs were UV-inscribed in hydrogenated PS750 fiber using a custom-designed phase mask with different grating lengths of 3 mm, 5 mm, 9 mm, 12 mm and 15 mm, showing polarization dependent losses (PDLs) of 1 dB, 3 dB, 7 dB, 10 dB and 13 dB, respectively. The power side-tapping efficiency is clearly depending on the grating strength. It has been identified that the power tapping efficiency increases with the grating strength and deceases along the grating length. The side-tapped power profile has also been examined in azimuthal direction, showing a near-Gaussian distribution. These experimental results clearly demonstrated that 45°- TFGs may be used as in-fiber power tapping devices for applications requiring in-line signal monitoring.

Fabrication of High Quality Broadband Type IIA Chirped Fiber Bragg Gratings

Chirped fiber Bragg gratings have found many applications in optical communication and sensing systems. High quality filters based on chirped fiber Bragg gratings with reflection bandwidth of 2.6 and 32nm and high reflectivity are demonstrated experimentally with 2 and 4cm long phase masks, respectively. These filters with flat reflection band and high reflectivity are achieved by writing type IIA chirped Bragg gratings.