无界域上具有记忆的非自治Plate方程随机吸引子的存在性

研究无界域上一类具有衰退记忆和加性噪声的非自治Plate方程解的长时间行为.利用一致估计验证了解的拉回渐近紧性,获得了其随机吸引子的存在性.

Wear-resisting Oxide Films for 900℃

A study was conducted to develop low-friction, wear-resistant surfaces on high temperature alloys for the temperature range from 26℃ to 900℃. The approach investigated consists of modifying the naturally occurring oxide film in order to improve its tribological properties. Improvement is needed at low temperatures where the oxide film, previously formed at high temperature, spalls due to stresses induced by sliding. Experiments with Ti, W and Ta additions show a beneficial effect when added to Ni and Ni-base alloys. Low friction can be maintained down to 100℃ from 900℃. For unalloyed Ni friction and surface damage increases at 400℃ to 500℃. Two new alloys were perpared based on the beneficial results of binary alloys and ZrO2 diffusion in Ni.Low friction at temperature above 500℃ and reasonable values (0.32~0.42) at low temperature are obtained.

MICROSTRUCTURES OF A NOVEL HIGH STRENGTH AND WEAR-RESISTING ZINC ALLOY

ＭＩＣＲＯＳＴＲＵＣＴＵＲＥＳＯＦＡＮＯＶＥＬＨＩＧＨＳＴＲＥＮＧＴＨＡＮＤＷＥＡＲ－ＲＥＳＩＳＴＩＮＧＺＩＮＣＡＬＬＯＹＬｉＹｕａｎｙｕａｎ；ＸｉａＷｅｉ；ＮｇａｉＴｕｎｇｗａｉＬｅｏ；ＬｕｏＪｕｎｍｉｎｇ；ＺｈｅｎｇＬｉｎｇｙｉ（Ｄｅｐａｒｔｍｅ...

Effect of Reduction on Bonding Interface of Hot-rolled Wear-resistant Steel BTW1/Q345R Cladding Plate

Wear-resistant cladding plates consisting of a substrate（Q345 R） and a clad layer（BTW1） were bonded through hot rolling at the temperature of 1 200 ℃ and a rolling speed of 0.5 m/s. The microhardness of the cladding plate was also tested after being heat treated. The microstructure evolution on the interface of BTW1/Q345 R sheets under various reduction rates was investigated with a scanning electron microscope（SEM） and EBSD. It is found that the micro-cracks and oxide films on the interface disappear when the reduction is 80%, whereas the maximum uniform diffusion distance reaches 10 μm. As a result, a wide range of metallurgical bonding layers forms, which indicates an improved combination between the BTW1 and the Q345 R. Additionally, it is discovered that the unbroken oxide films on the interface are composed of Mn, Si or Cr at the reductions of 50% and 65%. The SEM fractography of tensile specimen demonstrates that the BTW1 has significant dimple characteristics and possesses lower-sized dimples with the increment in reduction, suggesting that the toughness and bonding strength of the cladding plates would be improved by the increase of reduction. The results reveal that a high rolling reduction causes the interfacial oxide film broken and further forms a higher-sized composite metallurgical bonding interface. The peak microhardness is achieved near the interface.

A theory for three-dimensional response of micropolar plates

Through combined applications of the transfer-matrix method and asymptotic expansion technique,we formulate a theory to predict the three-dimensional response of micropolar plates.No ad hoc assumptions regarding through-thickness assumptions of the field variables are made,and the governing equations are two-dimensional,with the displacements and microrotations of the mid-plane as the unknowns.Once the deformation of the mid-plane is solved,a three-dimensional micropolar elastic field within the plate is generated,which is exact up to the second order except in the boundary region close to the plate edge.As an illustrative example,the bending of a clamped infinitely long plate caused by a uniformly distributed transverse force is analyzed and discussed in detail.

Analysis of High-Cr Cast Iron/Low Carbon Steel Wear-resistant Laminated Composite Plate Prepared by Hot-rolled Symmetrical Billet

This study developed a new technology for preparing high-chromium cast iron(HCCI)/low-carbon steel(LCS)wear-resistant composite plates by hot rolling at a 1050°C and a rolling speed of 0.2 m/s.The effects of different rolling reductions(30%,45%,and 60%)on the microstructure(interface and HCCI layer)and mechanical properties(bonding strength,hardness,and wear resistance)of the composite plate were studied.SEM images showed that when the reduction was increased,no impurities and interlayers were found between the microscopic interfaces after hot rolling,and the bonding interface exhibited a wave-like shape.EDS analysis showed that the Cr element diffusion between two metals after hot rolling was promoted when the reduction was increased,thereby improving the bonding quality under the same rolling temperature and rolling speed.Experiments showed that due to the stress release effect of the LCS of the cladded layer,the macro-slab shape after hot rolling performed well,and the brittle HCCI layer underwent thermoplastic deformation without cracking.Moreover,the increase of rolling reduction improved the bonding quality.As the rolling reduction was increased,the volume fraction of Cr-carbides in the HCCI layer also increased,resulting in an increase of hardness and wear-resistance.

Improved YOLOv8n Model for Detecting Helmets and License Plates on Electric Bicycles

Wearing helmetswhile riding electric bicycles can significantly reduce head injuries resulting fromtraffic accidents.To effectively monitor compliance,the utilization of target detection algorithms through traffic cameras plays a vital role in identifying helmet usage by electric bicycle riders and recognizing license plates on electric bicycles.However,manual enforcement by traffic police is time-consuming and labor-intensive.Traditional methods face challenges in accurately identifying small targets such as helmets and license plates using deep learning techniques.This paper proposes an enhanced model for detecting helmets and license plates on electric bicycles,addressing these challenges.The proposedmodel improves uponYOLOv8n by deepening the network structure,incorporating weighted connections,and introducing lightweight convolutional modules.These modifications aim to enhance the precision of small target recognition while reducing the model’s parameters,making it suitable for deployment on low-performance devices in real traffic scenarios.Experimental results demonstrate that the model achieves an mAP@0.5 of 91.8%,showing an 11.5%improvement over the baselinemodel,with a 16.2%reduction in parameters.Additionally,themodel achieves a frames per second(FPS)rate of 58,meeting the accuracy and speed requirements for detection in actual traffic scenarios.

A Dynamic Coupling of Ocean and Plate Motion

Plate motion representing a remarkable Earth process is widely attributed to several primary forces such as ridge push and slab pull. Recently, we have presented that the ocean water pressure against the wall of continents may generate enormous force on continents. Continents are physically fixed on the top of the lithosphere that has been already broken into individual plates, this attachment enables the force to be laterally transferred to the lithospheric plates. In this study, we combine the force and the existing plate driving forces (i.e., ridge push, slab pull, collisional, and shearing) to account for plate motion. We show that the modelled movements for the South American, African, North American, Eurasian, Australian, Pacific plates are well agreement with the observed movements in both speed and azimuth, with a Root Mean Square Error (RMSE) of the modelled speed against the observed speed of 0.91, 3.76, 2.77, 2.31, 7.43, and 1.95 mm/yr, respectively.

Identification of the Caroline Plate boundary:constraints from magnetic anomaly

The Caroline Plate is located among the Pacific Plate,the Philippine Sea Plate,and the India Australia Plate,and plays a key role in controlling the spreading direction of the Philippine Sea Plate.The Caroline Submarine Plateau(or Caroline Ridge)and the Eauripik Rise on the south formed a remarkable T-shaped large igneous rock province,which covered the northern boundary between the Caroline Plate and the Pacific Plate.However,relationship between these tectonic units and magma evolution remains unclear.Based on magnetic data from the Earth Magnetic Anomaly Grid(2-arc-minute resolution)(V2),the normalized vertical derivative of the total horizontal derivative(NVDR-THDR)technique was used to study the boundary of the Caroline Plate.Results show that the northern boundary is a transform fault that runs 1400 km long in approximately 28 km wide along the N8°in E-W direction.The eastern boundary is an NNW-SSE trending fault zone and subduction zone with a width of tens to hundreds of kilometers;and the north of N4°is a fracture zone of dense faults.The southeastern boundary may be the Lyra Trough.The area between the southwestern part of the Caroline Plate and the Ayu Trough is occupied by a wide shear zone up to 100 km wide in nearly S-N trending in general.The Eauripik transform fault(ETF)in the center of the Caroline Plate and the fault zones in the east and west basins are mostly semi-parallel sinistral NNW-SSE–trending faults,which together with the eastern boundary Mussau Trench(MT)sinistral fault,the northern Caroline transform fault(CTF),and the southern shear zone of the western boundary,indicates the sinistral characteristics of the Caroline Plate.The Caroline hotspot erupted in the Pacific Plate near the CTF and formed the west Caroline Ridge,and then joined with the Caroline transform fault at the N8°.A large amount of magma erupted along the CTF,by which the east Caroline Ridge was formed.At the same time,a large amount of magma developed southward via the eastern branch of the ETF,forming the northern segment of the Eauripik Rise.Therefore,the magmatic activity of the T-shaped large igneous province is obviously related to the fault structure of the boundary faults between the Caroline Plate and Pacific Plate,and the active faults within the Caroline Plate.

Generative optimization of bistable plates with deep learning

Bistate plates have found extensive applications in the domains of smart structures and energy harvesting devices.Most bistable curved plates are characterized by a constant thickness profile.Regrettably,due to the inherent complexity of this problem,relatively little attention has been devoted to this area.In this study,we demonstrate how deep learning can facilitate the discovery of novel plate profiles that cater to multiple objectives,including maximizing stiffness,forward snapping force,and backward snapping force.Our proposed approach is distinguished by its efficiency in terms of low computational energy consumption and high effectiveness.It holds promise for future applications in the design and optimization of multistable structures with diverse objectives,addressing the requirements of various fields.

Imaging plate scanners calibration and the attenuation behavior of imaging plate signals

Based on previously reported work, we propose a new method for calibrating image plate(IP) scanners, offering greater flexibility and convenience, which can be extended to the calibration tasks of various scanner models. This method was applied to calibrate the sensitivity of a GE Typhoon FLA 7000 scanner. Additionally, we performed a calibration of the spontaneous signal attenuation behavior for BAS-MS, BAS-SR, and BAS-TR type IPs under the 20±1℃ environmental conditions, and observed significant signal carrier diffusion behavior in BAS-MS IP. The calibration results lay a foundation for further research on the interaction between ultra-short, ultra-intense lasers and matter.

Modeling Geometrically Nonlinear FG Plates: A Fast and Accurate Alternative to IGA Method Based on Deep Learning

Isogeometric analysis (IGA) is known to showadvanced features compared to traditional finite element approaches.Using IGA one may accurately obtain the geometrically nonlinear bending behavior of plates with functionalgrading (FG). However, the procedure is usually complex and often is time-consuming. We thus put forward adeep learning method to model the geometrically nonlinear bending behavior of FG plates, bypassing the complexIGA simulation process. A long bidirectional short-term memory (BLSTM) recurrent neural network is trainedusing the load and gradient index as inputs and the displacement responses as outputs. The nonlinear relationshipbetween the outputs and the inputs is constructed usingmachine learning so that the displacements can be directlyestimated by the deep learning network. To provide enough training data, we use S-FSDT Von-Karman IGA andobtain the displacement responses for different loads and gradient indexes. Results show that the recognition erroris low, and demonstrate the feasibility of deep learning technique as a fast and accurate alternative to IGA formodeling the geometrically nonlinear bending behavior of FG plates.

Performance analysis of single-focus phase singularity based on elliptical reflective annulus quadrangle-element coded spiral zone plates

Optical vortices generated by the conventional vortex lens are usually disturbed by the undesired higher-order foci,which may lead to additional artifacts and thus degrade the contrast sensitivity. In this work, we propose an efficient methodology to combine the merit of elliptical reflective zone plates(ERZPs) and the advantage of spiral zone plates(SZPs) in establishing a specific single optical element, termed elliptical reflective annulus quadrangle-element coded spiral zone plates(ERAQSZPs) to generate single-focus phase singularity. Differing from the abrupt reflectance of the ERZPs, a series of randomly distributed nanometer apertures are adopted to realize the sinusoidal reflectance. Typically, according to our physical design, the ERAQSZPs are fabricated on a bulk substrate;therefore, the new idea can significantly reduce the difficulty in the fabrication process. Based on the Kirchhoff diffraction theory and convolution theorem, the focusing performance of ERAQSZPs is calculated. The results reveal that apart from the capability of generating optical vortices,ERAQSZPs can also integrate the function of focusing, energy selection, higher-order foci elimination, as well as high spectral resolution together. In addition, the focusing properties can be further improved by appropriately adjusting the parameters, such as zone number and the size of the consisted primitives. These findings are expected to direct a new direction toward improving the performance of optical capture, x-ray fluorescence spectra, and forbidden transition.

A low-frequency and broadband wave-insulating vibration isolator based on plate-shaped metastructures

A metamaterial vibration isolator,termed as wave-insulating isolator,is proposed,which preserves enough load-bearing capability and offers ultra-low and broad bandgaps for greatly enhanced wave insulation.It consists of plate-shaped metacells,whose symmetric and antisymmetric local resonant modes offer several low and broad mode bandgaps although the complete bandgap remains high and narrow.The bandgap mechanisms,vibration isolation properties,effects of key parameters,and robustness to complex conditions are clarified.As experimentally demonstrated,the wave-insulating isolator can improve the vibration insulation in the ranges of[50 Hz,180 Hz]and[260 Hz,400 Hz]by 15 dB and 25 dB,respectively,in contrast to the conventional isolator with the same first resonant frequency.

The interaction between a shaped charge jet and a single moving plate

Reactive armour is a very efficient add-on armour against shaped charge threats.Explosive reactive armour consists of one or several plates that are accelerated by an explosive.Similar but less violent acceleration of plates can also be achieved in a completely inert reactive armour.To be efficient against elongated jets,the motion of the plates needs to be inclined against the jet such that a sliding contact between the jet and the plates is established.This sliding contact causes a deflection and thinning of the jet.Under certain circumstances,the contact will become unstable,leading to severe disturbances on the jet.These disturbances will drastically reduce the jet penetration performance and it is therefore of interest to study the conditions that leads to an unstable contact.Previous studies on the interaction between shaped charge jets and flyer plates have shown that it is mainly the forward moving plate in an explosive reactive armour that is effective in disturbing the jet.This is usually attributed to the higher plate-to-jet mass flux ratio involved in the collision of the forward moving plate compared to the backward moving plate.For slow moving plates,as occurs in inert reactive armour,the difference in mass flux for the forward and backward moving plate is much lesser,and it is therefore of interest to study if other factors than the mass flux influences on the protection capability.In this work,experiments have been performed where a plate is accelerated along its length,interacting with a shaped charge jet that is fired at an oblique angle to the plate’s normal,either against or along the plate’s velocity.The arrangement corresponds to a jet interacting with a flyer plate from a reactive armour,with the exception that the collision velocity is the same for both types of obliquities in these experiments.The experiments show that disturbances on the jet are different in the two cases even though the collision velocities are the same.Numerical simulations of the interaction support the observation.The difference is attributed to the character of the contact pressure in the interaction region.For a backward moving plate,the maximum contact pressure is obtained at the beginning of the interaction zone and the contact pressure is therefore higher upstream than downstream of the jet while the opposite is true for a forward moving plate.A negative interface pressure gradient with respect to the jet motion results in a more stable flow than a positive,which means that the jet-plate contact is more stable for a backward moving plate than for a forward moving plate.A forward moving plate is thus more effective in disturbing the jet than a backward moving plate,not only because of the higher jet to plate mass flux ratio but also because of the character of the contact with the jet.

Temperature insensitivity of an all-fiber quarter-wave plate device fabricated with a high-birefringence fiber

A high-birefringence fiber,Tb:YAG crystal-derived silica fiber(TYDSF),was fabricated by CO_(2)laser-heating drawing technique.Its linear birefringence was 2.99×10^(-5),and it was used to fabricate an all-fiber quarter-wave plate(QWP)device.The polarization extinction ratio(PER)of the device was 0.29 dB,and its ellipticity was 44.26°at 25℃.In the temperature range of-5℃to 200℃,its PER was always less than 0.80 dB,and the fluctuation of PER and ellipticity was also small.Compared with QWPs fabricated with PANDA-type polarization-maintaining fiber(PMF)and elliptical-core PMF,the performance of TYDSF QWP was least sensitive to temperature.Furthermore,the TYDSF QWP was used in a high-power laser system,still maintaining good circular polarization state,and the nonlinear effects were suppressed in the system.The experimental results are of great significance to high-power lasers,fiber-optic current sensors,etc.,in harsh environments.

PVDF-assisted pyrolysis strategy for corrugated plate oxygen electrocatalysis nanoreactor:Simultaneously realizing efficient active sites and rapid mass transfer

Though Zn-air batteries(ZABs)are one of the most promising system for energy storage and conversion,challenge still persists in its commercial application due to the sluggish kinetics of oxygen reduction/evolution reaction(ORR/OER).Hereby,a polyvinylidene fluoride(PVDF)-assisted pyrolysis strategy is proposed to develop a novel corrugated plate-like bifunctional electrocatalyst using two-dimensional zeolitic imidazolate frameworks(2D ZIF-67)as the precursor.The employed PVDF plays an important role in inheriting the original 2D structure of ZIF-67 and modulating the composition of the final products.As a result,a corrugated plate-like electrocatalyst,high-density Co nanoparticles decorated 2D Co,N,and F tri-doped carbon nanosheets,can be obtained.The acquired electrocatalyst enables efficient active sites and rapid mass transfer simultaneously,thus showing appreciable electrocatalytic performance for rechargeable Zn-air batteries.Undoubtedly,our proposed strategy offers a new perspective to the design of advanced oxygen electrocatalysts.

Ultimate Strength of Hull Perforated Plate Under Extreme Cyclic Loading

In this study, the influence of opening parameters on the ultimate strength of perforated plates subjected to extreme cyclic loading in the presence of material kinematic hardening and isotro pic hardening was analyzed. It is found that the ultimate strength of the perforated plates decreases rapidly and stabilizes in the first four cycles. Plates with oblong openings have a greater ultimate strength compared to plates with rectangular openings, while the relative strengthening ratio decreases over the duration of the cycle. The location of the openings is also an important parameter that affects the strength of the structure, as the plates with openings close to the edges in the longitudinal direction have higher strengths, while in the transverse direction the strengths are higher when the openings are close to the center. Among the three opening-strengthening methods compared, the Carling stiffener method maintains a better strengthening effect under cyclic loads for many periods.

Heat-Generating Effects Involving Multiple Nanofluids in a Hybrid Convective Boundary Layer Flow on the Sloping Plate in a Porous Medium

The hybrid convective boundary layer circulation involving multiple nanofluids via a medium with pores is approaching a sloping plate. An investigation regarding the heat-generating effects upon the examined nanofluid flows has been carried out through computational analysis. A mathematical framework employing governing differential equations that are partial has been implemented to produce an ensemble of ordinary differential equations, which happen to be nonlinear that incorporate nanofluid flows by utilizing acceptable transformations. Through the combination of the Nachtsheim-Swigert shooting method and the Runge-Kutta method, the group of resulting non-dimensionalized equations is solved computationally. In a few special, confined cases, the corresponding numeric output is thereafter satisfactorily matched with the existing available research. The consequences of heat generation regarding local skin friction coefficient and rate of heat in conjunction with mass transfer have been investigated, evaluated, and reported on the basis of multiple nanofluid flows.

Impact of radiation,melting,and chemical reaction on magnetohydrodynamics nanoparticle aggregation flow across parallel plates

The heat transfer between two corresponding plates,disks,and concentric pipes has many applications,including water cleansing and lubrication.Furthermore,TiO_(2)-water-based nanofluids are used widely because it is useful for operating and controlling the temperature,especially in photovoltaic technology and solar panels.Motivated by these applications,the current study is based on the nanoparticle aggregation effect on magnetohydrodynamics(MHD)flow via rotating parallel plates with the chemical reaction.To achieve maximum heat transportation,the Bruggeman model is used to adapt the Maxwell model.Also,melting and thermal radiation effects are considered in the modeling to discuss heat transport.The Runge-Kutta-Fehlberg 4th−5th order method is used to attain numerical solutions.The main focus of this study is to see the thermodynamic behavior considering several aspects of nanoparticle aggregation.The heat transfer rate between the parallel plates is enhanced by improving the thermophoresis,radiation,and Brownian motion parameters.The rise in Schmidt number and chemical reaction rate parameter decreases the concentration distribution.This study will be helpful in enhancing the thermal efficiency of photovoltaic technology in solar plates,water purifying,thermal management of electronic devices,designing effective cooling systems,and other sustainable technologies.