Creep lives of high Cr ferritic heat resisting steel weldments decrease due to Type Ⅳ fracture, which occurs as a result of formation and growth of creep voids and cracks on grain boundaries in fine-grained heat affe...Creep lives of high Cr ferritic heat resisting steel weldments decrease due to Type Ⅳ fracture, which occurs as a result of formation and growth of creep voids and cracks on grain boundaries in fine-grained heat affected zone (HAZ). Because boron is considered to suppress the coarsening of grain boundary precipitates and growth of creep voids, we have investigated the effect of boron addition on the creep properties of 9Cr steel weldments. Four kinds of 9Cr3WSCoVNb steels with boron content varying from 4.7×10-5 to 1.8×10-4 and with nitrogen as low as 2.0×10-5 were prepared. The steel plates were welded by gas tungsten arc welding and crept at 923K. It was found that the microstructures of HAZ were quite different from those of conventional high Cr steels such as P91 and P92, namely the fine-grained HAZ did not exist in the present steel weldments. Boron addition also has the effect to suppress coarsening of grain boundary carbides in HAZ during creep. As a result of these phenomena, the welded joints of present steels showed no Type Ⅳ fractures and much better creep lives than those of conventional steels.展开更多
In this study, a new R-δf-type welding window on charge parameters is constructed by determining the boundary conditions of the explosive ratio. The R-δf-type welding window synthetically considers the explosive pro...In this study, a new R-δf-type welding window on charge parameters is constructed by determining the boundary conditions of the explosive ratio. The R-δf-type welding window synthetically considers the explosive properties and material properties, and can quickly determine the explosive charge at different welding materials with different thickness. In order to test the practicability and accuracy of the R-δf-type welding window, 410S stainless steel and Q345R low alloy steel plates were explosively welded using 15 mm charge determined by the new window. Microstructures of the bonded sections were examined and then shear tests were carried out on the bonded specimens. Microstructural examination showed the joint interface was transformed from micro wavy to small wavy appearance without microstructure defects. Shear tests results showed inter inacial shear strength was much higher than that of the national first grade standard. So the R-δf-type welding window has strong practicability and accuracy and is helpful to the practical production and application of explosive welding composite materials.展开更多
A series of fundamental experimental investigation was conducted in order to examine the effect of PWHT by sheet-type ceramic heater on the residual stress, deformation and compressive behavior of non-stiffened welded...A series of fundamental experimental investigation was conducted in order to examine the effect of PWHT by sheet-type ceramic heater on the residual stress, deformation and compressive behavior of non-stiffened welded box columns. The sheet-type ceramic heater was able to control the required temperature history for PWHT with high accuracy. The welding-induced tensile and compressive residual stresses of the specimens were reduced by 90% and 76% respectively with PWHT. Besides, PWHT could reduce the welding-induced out-of-plane deformation by 22%. It was revealed that the PWHT specimens had a slight higher stiffness than the As-welded specimens when applying monotonic static compressive load on both As-welded and PWHT specimens. They could also enhance the ultimate compressive load capacity about 32% of that of the As-welded specimens. The effectiveness of PWHT with the sheet-type ceramic heater could be confirmed.展开更多
A simulation method for microscopic creep damage at grain boundaries in the fine-grain heat-affected zone of low-alloy steel welds involving high energy piping was proposed on the basis of the combination of elastic-c...A simulation method for microscopic creep damage at grain boundaries in the fine-grain heat-affected zone of low-alloy steel welds involving high energy piping was proposed on the basis of the combination of elastic-creep FEM (finite element method) analysis and random fracture resistance modeling of the materials. The procedure to determine the initiation and growth-driving forces of small defects were briefly described. Then, a simulation procedure combining the stress distribution from elastic-creep FEM and the random fracture resistance model was proposed, and Ms procedure was applied to the simulation of the microscopic damage progress in a welded joint model test and in actual power piping. The results in terms of the simulated number density of small defects throughout the wall thickness were in good agreement with the observed results.展开更多
缆式焊丝熔化极气体保护电弧焊(gas metal arc welding,GMAW)中存在的焊缝截面侧偏现象会导致焊接接头熔合不良,基于熔滴受力分析和最小电压理论对焊缝截面侧偏现象的变化规律进行机理分析.结果表明,电流是影响截面侧偏的关键因素,由于...缆式焊丝熔化极气体保护电弧焊(gas metal arc welding,GMAW)中存在的焊缝截面侧偏现象会导致焊接接头熔合不良,基于熔滴受力分析和最小电压理论对焊缝截面侧偏现象的变化规律进行机理分析.结果表明,电流是影响截面侧偏的关键因素,由于缆式焊丝独特的绞合结构引起电弧旋转,进而导致出现熔滴受力不均的现象,熔滴过渡方向与焊丝轴线存在夹角,在熔滴冲击力的作用下导致焊缝截面出现侧偏现象,随着电流的增加,电弧对熔滴的拘束增强,熔滴过渡方向逐渐趋于轴线,因而焊缝截面侧偏的趋势随着电流增加而减小.展开更多
文摘Creep lives of high Cr ferritic heat resisting steel weldments decrease due to Type Ⅳ fracture, which occurs as a result of formation and growth of creep voids and cracks on grain boundaries in fine-grained heat affected zone (HAZ). Because boron is considered to suppress the coarsening of grain boundary precipitates and growth of creep voids, we have investigated the effect of boron addition on the creep properties of 9Cr steel weldments. Four kinds of 9Cr3WSCoVNb steels with boron content varying from 4.7×10-5 to 1.8×10-4 and with nitrogen as low as 2.0×10-5 were prepared. The steel plates were welded by gas tungsten arc welding and crept at 923K. It was found that the microstructures of HAZ were quite different from those of conventional high Cr steels such as P91 and P92, namely the fine-grained HAZ did not exist in the present steel weldments. Boron addition also has the effect to suppress coarsening of grain boundary carbides in HAZ during creep. As a result of these phenomena, the welded joints of present steels showed no Type Ⅳ fractures and much better creep lives than those of conventional steels.
基金supported by the National Natural Science Foundation of China(Grant No.51541112)
文摘In this study, a new R-δf-type welding window on charge parameters is constructed by determining the boundary conditions of the explosive ratio. The R-δf-type welding window synthetically considers the explosive properties and material properties, and can quickly determine the explosive charge at different welding materials with different thickness. In order to test the practicability and accuracy of the R-δf-type welding window, 410S stainless steel and Q345R low alloy steel plates were explosively welded using 15 mm charge determined by the new window. Microstructures of the bonded sections were examined and then shear tests were carried out on the bonded specimens. Microstructural examination showed the joint interface was transformed from micro wavy to small wavy appearance without microstructure defects. Shear tests results showed inter inacial shear strength was much higher than that of the national first grade standard. So the R-δf-type welding window has strong practicability and accuracy and is helpful to the practical production and application of explosive welding composite materials.
文摘A series of fundamental experimental investigation was conducted in order to examine the effect of PWHT by sheet-type ceramic heater on the residual stress, deformation and compressive behavior of non-stiffened welded box columns. The sheet-type ceramic heater was able to control the required temperature history for PWHT with high accuracy. The welding-induced tensile and compressive residual stresses of the specimens were reduced by 90% and 76% respectively with PWHT. Besides, PWHT could reduce the welding-induced out-of-plane deformation by 22%. It was revealed that the PWHT specimens had a slight higher stiffness than the As-welded specimens when applying monotonic static compressive load on both As-welded and PWHT specimens. They could also enhance the ultimate compressive load capacity about 32% of that of the As-welded specimens. The effectiveness of PWHT with the sheet-type ceramic heater could be confirmed.
文摘A simulation method for microscopic creep damage at grain boundaries in the fine-grain heat-affected zone of low-alloy steel welds involving high energy piping was proposed on the basis of the combination of elastic-creep FEM (finite element method) analysis and random fracture resistance modeling of the materials. The procedure to determine the initiation and growth-driving forces of small defects were briefly described. Then, a simulation procedure combining the stress distribution from elastic-creep FEM and the random fracture resistance model was proposed, and Ms procedure was applied to the simulation of the microscopic damage progress in a welded joint model test and in actual power piping. The results in terms of the simulated number density of small defects throughout the wall thickness were in good agreement with the observed results.
文摘缆式焊丝熔化极气体保护电弧焊(gas metal arc welding,GMAW)中存在的焊缝截面侧偏现象会导致焊接接头熔合不良,基于熔滴受力分析和最小电压理论对焊缝截面侧偏现象的变化规律进行机理分析.结果表明,电流是影响截面侧偏的关键因素,由于缆式焊丝独特的绞合结构引起电弧旋转,进而导致出现熔滴受力不均的现象,熔滴过渡方向与焊丝轴线存在夹角,在熔滴冲击力的作用下导致焊缝截面出现侧偏现象,随着电流的增加,电弧对熔滴的拘束增强,熔滴过渡方向逐渐趋于轴线,因而焊缝截面侧偏的趋势随着电流增加而减小.
