窄间隙P-GMAW仰焊位置熔滴过渡影响因素及控制方法

管道窄间隙全位置焊接过程中,在接近仰焊位置容易出现焊接缺陷,制约了管道施工的质量和效率.文中针对管道自动焊仰焊位置成形差、可靠性低的问题,分析P-GMAW过程送丝速度、弧长修正、导电嘴到熔池距离等因素对熔滴过渡的影响规律.结果表明,增加弧长修正系数可以增大电弧对侧壁的热输入,能够缓解侧壁熔合不良的问题,但会使熔滴过渡路径难以控制.因此当焊枪运动到仰焊位置时,提高送丝速度有利于获得更小的熔滴、更高的过渡频率;降低导电嘴到熔池距离,可以增加电磁力、减小熔滴尺寸,从而更有利于仰焊位置熔滴向熔池的过渡,研究结果对于管道窄间隙焊接的工艺设计具有一定的指导意义.

基于摆动激光扫描的GMAW焊缝成形调控

将摆动激光与GMAW工艺复合,利用“8”字形摆动激光扫描液态熔池,对其温度场和流场进行调控,以改变熔池温度梯度,主动调控熔池流动以改善焊缝成形.在6061铝合金板材表面进行堆焊试验,重点探究了光丝间距、摆动幅度、激光功率对于焊缝成形的影响,采用高速摄像机拍摄激光扫描熔池过程.结果表明,摆动激光扫描可以有效抑制成形缺陷的发生,当摆动激光扫描熔池中部时可以获得最佳的焊缝成形效果.摆动激光扫描降低了熔池温度梯度分布,同时激光扫描产生的激光蒸发反力可以驱动熔池流动,促进了液态熔池的流动铺展,从而有效抑制了不规则焊缝成形缺陷,减少焊缝内部气孔和裂纹缺陷.调节摆动激光摆幅可以在一定范围内对焊缝宽度进行调控.

基于变分立体匹配算法的GMAW熔池形貌三维重建

为实现完整熔池表面形貌三维传感,构建了双棱镜单摄像机立体视觉传感系统.针对熔池图像纹理缺乏造成的立体匹配困难的问题,引入了全局优化的变分立体匹配算法,通过建立包含灰度差异数据项和空间连续性约束项的能量函数的可行性泛函,经过迭代求解获得具有丰富细节的熔池表面稠密视差图.对自制非标准凹面形状进行立体匹配和三维重建,结果表明,宽度误差小于3.16%,深度误差小于4.82%.基于该算法实现了熔化极气体保护焊(gas metal arc welding,GMAW)的堆焊及V形坡口对焊条件下,不同熔透状态熔池稠密视差图计算和表面形貌的三维重建.

Q690D多道次GMAW接头的组织和力学性能

在无预热和焊后热处理的条件下,采用熔化极气体保护焊(GMAW)和CHW-80C1实芯焊丝对20 mm厚Q690D热机械轧制钢板进行多道次焊接试验,分析该钢焊接接头的组织转变特征和冲击性能。结果表明,采用CHW-80C1焊丝可获得成型优良的焊接接头;Q690D各道次的焊缝组织相似,均由粒状贝氏体和少量的针状铁素体、先共析铁素体组成;热影响区由粒状贝氏体、针状铁素体、先共析铁素体及M-A组元组成。焊缝与细晶热影响区的冲击吸收功相对于母材的有一定幅度的下降,焊缝与细晶热影响区的断裂类型均为韧性断裂。

基于电流多特征融合的窄间隙P-GMAW摆动电弧传感焊缝跟踪方法

电弧传感是实现窄间隙焊接焊缝跟踪的主要方式之一。针对电弧传感稳定性差、可靠性低的问题,提出融合摆动周期内电流信息的多个统计学特征进行偏差提取的方法,克服单一数据特征容易受到电弧稳定性影响、导致传感精度下降的问题。首先,提取电流信号的多个时域特征,计算特征矩阵与偏差矢量相关性;然后,取相关性高的特征用主成分分析的方法进行融合,取前两个主成分作为观测数据;最后,基于多分类的支持向量机模型对其进行分类试验。试验结果表明最大误差为0.2 mm,0.1 mm以内的误差占93.75%。该方法对比传统方法精度有所提升,对比神经网络方法,所用训练样本少,训练过程更加简单。

T型接头旋转激光+GMAW复合焊熔池动态行为数值分析模型

目的研究T型接头旋转光纤激光+GMAW复合焊熔池的温度场和流态特征,揭示气孔缺陷的产生及抑制机理。方法依据光学、电磁学、传热学及流体动力学机理,建立T型接头旋转光纤激光+GMAW复合焊熔池数值分析模型。使用Fluent软件对旋转频率分别为50 Hz和100 Hz的T型接头旋转激光+GMAW复合焊进行温度场以及流态特征的模拟,对比不同频率下T型接头横、纵截面,从工艺和焊缝成形角度出发,针对不同频率对熔池、小孔成形以及气孔抑制的影响进行讨论。结果当旋转频率为50 Hz时,纵截面内小孔最大深度为5.4 mm,横截面熔池内小孔开口直径相对较大,旋转一周后,小孔远离气泡,气泡无法逸出,形成气孔;当旋转频率为100 Hz时,纵截面内小孔深度显著降低,熔池体积明显减小,横截面内小孔最大开口直径和深度均降低,熔池尺寸也有所减小,在时间为0.097 s时,小孔上方区域出现的顺时针涡流不仅能抑制气孔,还能改善熔池的下垂以及立板焊趾处的咬边。结论随着旋转频率的增大,小孔的最大开口直径和深度均降低,还对熔池具有搅拌作用,使熔池体积变小。

P-GMAW起弧过程特征分析及稳定性判别方法

脉冲熔化极气体保护焊(pulsed gas metal arc welding,P-GMAW)起弧过程易产生不稳定现象,会严重影响电弧传感焊缝跟踪精度.针对这一问题,对摆动电弧窄间隙P-GMAW不稳定起弧过程的成因进行了研究,发现送丝速度对起弧过程稳定性具有重要影响.通过对电弧图像与电信号特征进行对比分析,提取了表征电弧稳定性的电信号特征变量;为减小变量冗余性和过拟合,采用最大似然估计法筛选并提取了8个变量,并通过主成分分析法(principal component analysis,PCA)对变量进行融合,提取了方差贡献率最高的前两个主成分;根据因子载荷发现,相比熔滴过渡阶段和基值阶段,脉冲峰值阶段是电弧更易发生不稳定现象的阶段.结合提取的主成分变量与二分类Logistic回归模型建立了起弧过程电弧稳定性判别模型.通过受试者工作特征(receiver operating characteristic,ROC)曲线得到了模型的最佳阈值.结果表明,该模型对脉冲稳定性判别准确率达到了80%以上,表明模型具有良好的判别性能.该模型对提高窄间隙高低跟踪精度、保证焊接质量具有一定应用价值.

缆式焊丝GMAW焊缝截面侧偏行为机理分析

缆式焊丝熔化极气体保护电弧焊(gas metal arc welding,GMAW)中存在的焊缝截面侧偏现象会导致焊接接头熔合不良,基于熔滴受力分析和最小电压理论对焊缝截面侧偏现象的变化规律进行机理分析.结果表明,电流是影响截面侧偏的关键因素,由于缆式焊丝独特的绞合结构引起电弧旋转,进而导致出现熔滴受力不均的现象,熔滴过渡方向与焊丝轴线存在夹角,在熔滴冲击力的作用下导致焊缝截面出现侧偏现象,随着电流的增加,电弧对熔滴的拘束增强,熔滴过渡方向逐渐趋于轴线,因而焊缝截面侧偏的趋势随着电流增加而减小.

基于双NURBS曲线的叶轮叶片工业机器人GMAW增材制造

以双NURBS曲线获得的直纹面广泛存在于各行业复杂零件中,如何实现复杂直纹面的增材制造一直是增材制造领域中极为关心的问题。以双NURBS曲线描述叶片模型,进一步获得直纹面,采用优化工艺参数,以GMAW方法实现了叶轮叶片的增材制造,增材获得的叶片完整,成形良好,表明以GMAW工艺实现双NURBS曲线叶片增材制造是可行的。为叶片模型构建、复杂形状叶片的电弧增材制造提供了新方法,对复杂形状零件增材制造过程控制具有借鉴意义。

高效多丝熔化极气体保护焊(GMAW)工艺的研究现状及进展

随着全球制造业竞争的日益激烈,我国提出了“中国制造2025”制造强国战略,其重点发展的十大领域中,与焊接技术密切相关的就高达八个,不仅极大地推动了焊接技术的革新发展,而且对焊接效率和质量均提出了更高的要求。由于熔化极气体保护焊(Gas metal arc welding,GMAW)易于实现自动化焊接,具有生产效率高、焊接质量好及位置适应性好等优点,所以广泛应用于机械制造业中。实现高效GMAW的主要途径有提高焊接速度以及焊接熔敷率。针对以上两种途径,国内外焊接工作者在双丝GMAW的基础上,引入了第三根甚至多根焊丝,研发了各种多丝GMAW工艺。本文针对国内外研发的各类多丝GMAW工艺进行了分析,重点介绍了多丝GMAW工艺的焊接原理、工艺特点及其应用,通过上述分析对各类多丝GMAW工艺进行归纳总结,并进一步展望了多丝焊接的发展方向,即多丝GMAW工艺亟需在电弧物理理论、设备开发和新焊材研发等方面展开深入的研究工作。

基于深度学习的GMAW焊接缺陷在线监测

以轨道交通高速高铁司机室铝合金外板为载体,围绕智能焊接关键技术,针对焊接缺陷在线监测问题开展研究.借助工艺试验平台与焊接工艺卡开展焊接缺陷试验设计、批量数据采集、专家经验标定、数据库构建,采用卷积神经网络算法对不同类型数据构建多维信息融合模型,并对融合模型进行参数优化处理,最终完成融合模型的训练、验证和测试.结果表明,训练后的融合模型比单一信息模型对焊接缺陷具有较好的识别结果,训练集和测试集的焊接缺陷监测精度分别为99.0%和88.3%,此监测系统的数据采集和模型响应总时间小于100 ms,能够满足工程化应用需求,提高机器人焊接的智能化水平,推动企业数字化转型升级.

窄间隙GMAW咬边缺陷的电弧声信号特征分析与识别

针对窄间隙熔化极气体保护焊(Gas Metal Arc Welding,GMAW)焊道侧壁处局部咬边缺陷检测困难的问题,提出了一种基于电弧声信号特征提取与处理的咬边缺陷在线检测方法。通过分析正常、临界咬边和咬边这3种焊接状态的电弧形态和电弧声信号特征,证实坡口侧壁引起的电弧形态变化是影响电弧声信号变化的重要因素。在此基础上采用小波包时频分析,同时引入特征类间标准差作为评价指标,确定了能有效识别3种焊接状态的敏感特征。采用Sigmoid支持向量机和五折交叉验证建立预测模型,实验结果表明该模型能较好地实现3种焊接状态的预测分类,识别准确率达到96.0%。

Recent research progress in the mechanism and suppression of fusion welding-induced liquation cracking of nickel based superalloys

Nickel-based superalloys are extensively used in the crucial hot-section components of industrial gas turbines,aeronautics,and astronautics because of their excellent mechanical properties and corrosion resistance at high temperatures.Fusion welding serves as an effective means for joining and repairing these alloys;however,fusion welding-induced liquation cracking has been a challenging issue.This paper comprehensively reviewed recent liquation cracking,discussing the formation mechanisms,cracking criteria,and remedies.In recent investigations,regulating material composition,changing the preweld heat treatment of the base metal,optimizing the welding process parameters,and applying auxiliary control methods are effective strategies for mitigating cracks.To promote the application of nickel-based superalloys,further research on the combination impact of multiple elements on cracking prevention and specific quantitative criteria for liquation cracking is necessary.

基于工程应用的CW-GMAW熔滴过渡形态表征

综述了涉及工程应用的冷丝熔化极气体保护焊(Cold wire gas metal arc welding,CW-GMAW)熔滴过渡形态特征。结果表明,在大电流、强规范、富氩混合气体保护下,CW-GMAW工艺的熔滴过渡形态呈喷射过渡;当电流较小、电弧电压较低时,可能为滴状过渡,甚至在弧压很低时,呈现短路过渡形态。该工艺电弧发生偏向冷丝的位移,弧长变短甚至发生短路,与冷丝送进速率比增高及冷丝在电弧中产生大量金属蒸气时弧柱电阻下降有关。在具有富氩混合保护气体的相同工艺参数下,CWGMAW转变电流比GMAW降低了4%~7%。焊接工艺参数对CW-GMAW和GMAW工艺熔滴过渡形态的影响规律大致相近,但前者因涉及冷丝送进速率比和电极焊丝送进速度,以及它们的匹配等,使焊接电流的影响更为复杂。

铝合金T型接头激光+GMAW复合焊残余应力数值分析

目的研究激光+GMAW复合焊中不同激光功率参数对铝合金T型接头残余应力的影响,从而提高焊接性能。方法分别考虑了热弹塑性理论、传热学以及T型接头几何特性,建立了铝合金T型接头激光+电弧复合焊残余应力的数值分析模型。采用双椭球体热源模型表征电弧热输入与熔滴晗,采用锥体热源模型对激光深熔焊进行描述。基于所建立的T型接头模型,使用ANSYS有限元软件对12 mm厚铝合金激光+GMAW焊T型接头残余应力进行模拟计算,并研究其分布特征;使用X射线衍射法对T型接头处的残余应力进行测量从而对所建模型的准确性进行验证。同时,对比了不同激光功率下铝合金T型接头对残余应力的影响规律。结果当激光功率分别为2、3、4、5 kW时,铝合金T型接头路径L3上的纵向残余应力最大值分别为270、263、258、251 MPa,米塞斯-等效应力最大值分别为265、261、257、250 MPa。结论后焊的焊缝A对焊缝B有明显的热处理作用,使应力明显降低;在T型接头焊缝及近缝区,横向残余应力和厚度方向残余应力峰值均比纵向残余应力峰值小,且随着激光功率的增大,焊缝及近缝区拉应力峰值不断减小。

Design of Fully Automatic Specification Selection System for Resistance Welding Equipment

A system for fully automatic selection of welding specifications in resistance welding equipment has been developed to address the problem of workers frequently choosing the wrong specifications during manual welding of multiple parts on a single machine in automobile factories. The system incorporates an automatic recognition system for different workpiece materials using the added machine fixture,visual detection system for nuts and bolts,and secondary graphical confirmation to ensure the correctness of specification calling. This system achieves reliable,fully automatic selection of welding specifications in resistance welding equipment and has shown significant effects in improving welding quality for massproduced workpieces,while solving the problem of specification calling errors that can occur with traditional methods involving process charts and code adjustments. This system is particularly suitable for promoting applications in manual welding of multiple parts on a single machine in automobile factories,ensuring correct specification calling and welding quality.

Theoretical analysis of the elastic Kelvin-Helmholtz instability in explosive weldings

By considering the joint effects of the Kelvin-Helmholtz(KH) and Rayleigh-Taylor(RT) instabilities, this paper presents an interpretation of the wavy patterns that occur in explosive welding. It is assumed that the elasticity of the material at the interface effectively determines the wavelength, because explosive welding is basically a solid-state welding process. To this end, an analytical model of elastic hydrodynamic instabilities is proposed, and the most unstable mode is selected in the solid phase. Similar approaches have been widely used to study the interfacial behavior of solid metals in high-energy-density physics. By comparing the experimental and theoretical results, it is concluded that thermal softening,which significantly reduces the shear modulus, is necessary and sufficient for successful welding. The thermal softening is verified by theoretical analysis of the increase in temperature due to the impacting and sliding of the flyer and base plates, and some experimental observations are qualitatively validated.In summary, the combined effect of the KH and RT instabilities in solids determines the wavy morphology, and our theoretical results are in good qualitative agreement with experimental and numerical observations.

Effect of process parameters on the morphology of aluminum/copper alloy lap joints by red and blue hybrid laser welding

In order to overcome the problems of many pores,large deformation and unstable weld quality of traditional laser welded aluminumcopper alloy joints,a red-blue dual-beam laser source and a swinging laser were introduced for welding.T2 copper and 6063 aluminum thin plates were lap welded by coaxial dual-beam laser welding.The morphology of weld cross section was compared to explore the influence of process parameters on the formation of lap joints.The microstructure characteristics of the weld zone were observed and compared by optical microscope.The results show that the addition of laser beam swing can eliminate the internal pores of the weld.With the increase of the swing width,the weld depth decreases,and the weld width increases first and then decreases.The influence of welding speed on the weld cross section morphology is similar to that of swing width.With the increase of welding speed,the weld width increases first and then decreases,while the weld depth decreases all the time.This is because that the red laser is used as the main heat source to melt the base metals,with the increase of red laser power,the weld depth increases.As an auxiliary laser source,blue laser reduces the total energy consumption,consequently,the effective heat input increases and the spatter is restrained effectively.As a result,the increase of red laser power has an enhancement effect on the weld width and weld depth.When the swing width is 1.2 mm,the red laser power is 550 W,the blue laser power is 500 W,and the welding speed is 35 mm/s,the weld forming is the best.The lap joint of T2 copper and 6063 aluminum alloy thin plate can be connected stably with the hybrid of blue laser.The effect rules of laser beam swing on the weld formation were obtained,which improved the quality of the joints.

A review of linear friction welding of Ni -based superalloys

Ni-based superalloys are one of the most important materials employed in high-temperature applications within the aerospace and nuclear energy industries and in gas turbines due to their excellent corrosion,radiation,fatigue resistance,and high-temperature strength.Linear friction welding(LFW)is a new joining technology with near-net-forming characteristics that can be used for the manu-facture and repair of a wide range of aerospace components.This paper reviews published works on LFW of Ni-based superalloys with the aim of understanding the characteristics of frictional heat generation and extrusion deformation,microstructures,mechanical proper-ties,flash morphology,residual stresses,creep,and fatigue of Ni-based superalloy weldments produced with LFW to enable future optim-um utilization of the LFW process.

MD Simulation of Diffusion Behaviors in Collision Welding Processes of Al-Cu, Al-Al, Cu-Cu

To investigate the effects of material combinations and velocity conditions on atomic diffusion behavior near collision interfaces,this study simulates the atomic diffusion behavior near collision interfaces in Cu-Al,Al-Al and Cu-Cu combinations fabricated through collision welding using molecular dynamic(MD)simulation.The atomic diffusion behaviors are compared between similar metal combinations(Al-Al,Cu-Cu)and dissimilar metal combinations(Al-Cu).By combining the simulation results and classical diffusion theory,the diffusion coefficients for similar and dissimilar metal material combinations under different velocity conditions are obtained.The effects of material combinations and collision velocity on diffusion behaviors are also discussed.The diffusion behaviors of dissimilar material combinations strongly depend on the transverse velocity,whereas those of the similar material combinations are more dependent on the longitudinal velocity.These findings can provide guidance for optimizing welding parameters.