Promoting dynamic recrystallization and improving strength and ductility of Mg-7Bi alloy through Al addition

This study investigated the influence of the addition of Al to a Mg-7Bi(B7,wt%)alloy,particularly its recrystallization behavior during extrusion and its resulting mechanical properties.The addition of 2 wt%Al to the B7 alloy resulted in a lower grain size,a reduction in the number density of fine Mg3Bi2 particles,and a higher area fraction of relatively coarse Mg3Bi2 particles in the extrusion billet.These microstructural changes increased the nucleation sites for recrystallization,reduced the Zener pinning effect,and enhanced particle-stimulated nucleation,all of which promoted dynamic recrystallization behavior during extrusion.As a result,the area fraction of recrystallized grains in the extruded alloy increased from 77%to 94%.The extruded B7 alloy exhibited a strong<10-10>fiber texture,whereas the extruded Mg-7Bi-2Al(BA72)alloy had a weak<10-10>-<2-1-10>texture,which was attributed to the minimal presence of unrecrystallized grains and the dispersed orientation of the recrystallized grains.The tensile yield strength(TYS)of the extruded BA72 alloy was higher than that of the extruded B7 alloy(170 and 124 MPa,respectively),which resulted from the enhanced grain-boundary and solid-solution strengthening effects.The tensile elongation(EL)of the BA72 alloy also exceeded that of the B7 alloy(20.3%and 6.1%,respectively),the result of the uniform formation of fine twins under tension in the former and the formation of a few coarse twins among the unrecrystallized grains in the latter.Consequently,the addition of a small amount of Al to the B7 alloy significantly improved both the strength and ductility of the extruded alloy,resulting in a remarkable increase in the product of the TYS and EL from 756 to 3451 MPa%and expanding its potential range of applications as a lightweight extruded structural component.

Effect of Fe Addition on Dehydrogenation Performance of Methylcyclohexance over Pt/Al_(2)O_(3)

Catalysts with varying Fe contents were prepared using a sequential impregnation method to investigate the effects of Fe addition on the physicochemical properties of Pt/Al_(2)O_(3) and their performance in methylcyclohexane(MCH)dehydrogenation.The results demonstrated that the addition of Fe to Pt/Al_(2)O_(3) enhanced the electron density of Pt and improved catalytic activity,while exhibiting negligible influence on the catalytic selectivity for toluene.When the Fe content was 0.057%,the catalyst exhibited the highest MCH consumption rate,which was approximately two times higher than that of the catalyst without Fe.Additionally,the incorporation of Fe inhibited the formation of coke and reduced the quantity of coke deposits on the catalyst,thereby improving its catalytic durability.Overall,Fe shows promise as a prospective secondary element for Pt/Al_(2)O_(3) to enhance the MCH dehydrogenation performance.

Effect of defatted flaxseed gum powder addition on the quality of sesame paste

The study explored the influence of defatted flaxseed gum powder(DFGP) on the stability and quality of sesame paste by measuring and analyzing its composition, color, texture, particle size, centrifugal oil separation rate,rheological properties, and microstructure. The results showed that the moisture and polysaccharide content of sesame paste was increased as the DFGP increased. Additionally, the hardness, gumminess, and chewiness of the sesame paste was improved, while the presence of particles with small particle size(1–100 μm) was decreased.The rate of oil precipitation was reduced by 28.99% when the amount of DFGP was 6%. The sesame paste samples exhibited pseudoplastic behavior, demonstrating shear thinning. As the shear rate increased, the apparent viscosity of sesame paste gradually decreased. Both the storage modulus(G’) and the loss modulus(G’’) increased as the shear frequency increased. The microstructure observation revealed that protein and oil were evenly distributed in the sesame paste system, and the addition of DFGP enhanced the bonding between oil and protein.This study can provide valuable references for high-quality sesame paste products in the food industry.

Dynamical Artificial Bee Colony for Energy-Efficient Unrelated Parallel Machine Scheduling with Additional Resources and Maintenance

Unrelated parallel machine scheduling problem(UPMSP)is a typical scheduling one and UPMSP with various reallife constraints such as additional resources has been widely studied;however,UPMSP with additional resources,maintenance,and energy-related objectives is seldom investigated.The Artificial Bee Colony(ABC)algorithm has been successfully applied to various production scheduling problems and demonstrates potential search advantages in solving UPMSP with additional resources,among other factors.In this study,an energy-efficient UPMSP with additional resources and maintenance is considered.A dynamical artificial bee colony(DABC)algorithm is presented to minimize makespan and total energy consumption simultaneously.Three heuristics are applied to produce the initial population.Employed bee swarm and onlooker bee swarm are constructed.Computing resources are shifted from the dominated solutions to non-dominated solutions in each swarm when the given condition is met.Dynamical employed bee phase is implemented by computing resource shifting and solution migration.Computing resource shifting and feedback are used to construct dynamical onlooker bee phase.Computational experiments are conducted on 300 instances from the literature and three comparative algorithms and ABC are compared after parameter settings of all algorithms are given.The computational results demonstrate that the new strategies of DABC are effective and that DABC has promising advantages in solving the considered UPMSP.

Soil bacterial and fungal communities resilience to long-term nitrogen addition in subtropical forests in China

Atmospheric nitrogen(N)deposition is predicted to increase,especially in the subtropics.However,the responses of soil microorganisms to long-term N addition at the molecular level in N-rich subtropical forests have not been clarified.A long-term nutrient addition experiment was conducted in a subtropical evergreen old-growth forest in China.The four treatments were:control,low N(50 kg N ha^(-1)a^(-1)),high N(100 kg N ha^(-1)a^(-1)),and combined N and phosphorus(P)(100 kg N ha^(-1)a^(-1)+50 kg P ha^(-1)a^(-1)).Metagenomic sequencing characterized diversity and composition of soil microbial communities and used to construct bacterial/fungal co-occurrence networks.Nutrient-treated soils were more acidic and had higher levels of dissolved organic carbon than controls.There were no significant differences in microbial diversity and community composition across treatments.The addition of nutrients increased the abundance of copiotrophic bacteria and potentially beneficial microorganisms(e.g.,Gemmatimonadetes,Chaetomium,and Aureobasidium).Low N addition increased microbiome network connectivity.Three rare fungi were identified as module hubs under nutrient addition,indicating that low abundance fungi were more sensitive to increased nutrients.The results indicate that the overall composition of microbial communities was stable but not static to long-term N addition.Our findings provide new insights that can aid predictions of the response of soil microbial communities to long-term N addition.

Effect of addition temperature on dispersion behavior and grain refinement efficiency of MgO introduced into Mg alloy

The effect of addition temperature of MgO particles(MgOp)on their dispersion behavior and the efficiency of grain refinement in AZ31 Mg alloy was investigated.In addition,the grain refinement mechanism was systematically studied by microstructure characterization,thermodynamic calculation,and analysis of solidification curves.The results show that the grain size of AZ31 Mg alloy initially decreases and then increases as the MgOp addition temperature is increased from 720 to 810℃,exhibiting a minimum value of 136μm at 780℃.The improved grain refinement efficiency with increasing MgOp addition temperature can be attributed to the reduced Mg melt viscosity and enhanced wettability between MgOp and Mg melt.Furthermore,a corresponding physical model describing the solidification behavior and grain refinement mechanism was proposed.

Belowground Bud Bank Is Insensitive to Short-Term Nutrient Addition in the Meadow Steppe of Inner Mongolia

Human activities and industrialization have significantly increased soil nutrients,such as nitrogen(N)and phos-phorus(P),profoundly impacting the composition and structure of plant community,as well as the ecosystem functions,especially in nutrient-limited ecosystems.However,as the key propagule pool of perennial grasslands,how belowground bud bank and its relationship with aboveground vegetation respond to short-term changes in soil nutrients was still unclear.In this study,we conducted a short-term(2021–2022)soil fertilization experiment with N addition(10 g N m^(-2) yr^(-1))and P addition(5 g N m^(-2) yr^(-1))in the meadow steppe of Inner Mongolia,China,to explore the responses of belowground bud bank,aboveground shoot population and their relationships(represented by the ratio of bud to shoot density-meristem limitation index(MLI))for the whole community and three plant functional groups(perennial rhizomatous grasses-PR,perennial bunchgrasses-PB,and perennial forbs-PF)to nutrient addition.The short-term nutrient addition had no significant influences on belowground bud density,aboveground shoot density,and MLI of the whole plant community.Plant functional groups showed different responses to soil fertilization.Specifically,N addition significantly increased the bud density and shoot density of PR,especially in combination with P addition.N addition reduced the shoot density of PF but had no influence on its bud density and MLI.Nutrient addition had significant effects on the three indicators of PB.Our study indicates that the belowground bud bank and its relationship with aboveground vegetation in temperate meadow steppe are insensitive to short-term soil fertilization,but plant functional groups exhibit specific responses in terms of population regeneration,which implies that plant community composition and ecosystem functions will be changed under the ongoing global change.

How Prime Numbers Are Interconnected and Built with Two Equations: Addition and Subtraction Rules the Function (6µ)

Are all prime numbers linked by four simple functions? Can we predict when a prime will appear in a sequence of primes? If we classify primes into two groups, Group 1 for all primes that appear before ζ (such that , for instance 5, ), an even number divisible by 3 and 2, and Group 2 for all primes that are after ζ (such that , for instance 7), then we find a simple function: for each prime in each group, , where n is any natural number. If we start a sequence of primes with 5 for Group 1 and 7 for Group 2, we can attribute a μ value for each prime. The μ value can be attributed to every prime greater than 7. Thus for Group 1, and . Using this formula, all the primes appear for , where μ is any natural number.

Stromal lenticule addition keratoplasty with corneal crosslinking for corneal ectasia secondary to FS-LASIK:a case series

●AIM:To explore the clinical efficacy and safety of stromal lenticule addition keratoplasty(SLAK)with corneal crosslinking(CXL)on patients with corneal ectasia secondary to femtosecond laser-assisted in situ keratomileusis(FS-LASIK).●METHODS:A series of 5 patients undertaking SLAK with CXL for the treatment of corneal ectasia secondary to FS-LASIK were followed for 4-9mo.The lenticules were collected from patients undertaking small incision lenticule extraction(SMILE)for the correction of myopia.Adding a stromal lenticule was aimed at improving the corneal thickness for the safe application of crosslinking and compensating for the thin cornea to improve its mechanical strength.●RESULTS:All surgeries were conducted successfully with no significant complications.Their best corrected visual acuity(BCVA)ranged from 0.05 to 0.8-2 before surgery.The pre-operational total corneal thickness ranged from 345-404μm and maximum keratometry(Kmax)ranged from 50.8 to 86.3.After the combination surgery,both the corneal keratometry(range 55.9 to 92.8)and total corneal thickness(range 413-482μm)significantly increased.Four out of 5 patients had improvement of corneal biomechanical parameters(reflected by stiffness parameter A1 in Corvis ST).However,3 patients showed decreased BCVA after surgery due to the development of irregular astigmatism and transient haze.Despite the onset of corneal edema right after SLAK,the corneal topography and thickness generally stabilized after 3mo.●CONCLUSION:SLAK with CXL is a potentially beneficial and safe therapy for advanced corneal ectasia.Future work needs to address the poor predictability of corneal refractometry and compare the outcomes of different surgical modes.

Effect of Ti-Mo-V composite addition on microstructure andmechanical properties of marine 10Ni5CrMoV steel

The effects of Ti-Mo-V composite addition on the evolution of precipitates in marine 10Ni5CrMoV steel andthe corresponding strength and toughness mechanisms were systematically investigated.Ti-Mo-V composite addition canform the Ti_(x)Mo_(y)V_(z)C carbide with TiC as core and Mo-V as shell in the order of Ti(C)→V→Mo.The yield strength of thespecimens is increased from 815 MPa to 876 MPa due to the nanoscale precipitates enhancing the pinning effect on grainboundaries and dislocations,and the contribution of precipitation and dislocation strengthening is increased.The decrease of ductile-brittle transition temperature from−103 to−116℃is attributed to the decrease in equivalent grainsize and the increase of high-angle grain boundary misorientation,which hinders the initiation and propagation of cracks.When the mass fraction of Ti is 0.05%,the strength and cryogenic toughness can be improved synergistically,which alsoprovides a theoretical basis and experimental reference for exploring the more excellent combination of strength andcryogenic toughness of marine 10Ni5CrMoV steel.

Effect of calcium addition on microstructure and texture modification of Mg rolled sheets

The mechanical properties and texture of AM60（Mg-6.0Al-0.3Mn,mass fraction %） and ZXM200（Mg-1.6Zn-0.5Ca-0.2Mn） Mg alloys subjected to multi-pass hot rolling were investigated.The finer recrystallized grains usually exhibit particular preferred orientations and then alter the total texture feature of rolled sheets.Ca solid solution into Mg matrix serves to the formation of texture component with c-axis rotated away from normal direction towards transverse direction and then weakens the overall texture intensity,resulting in a similar anisotropic characteristic to RE-containing Mg alloys.

Carbon and nitrogen dynamics in early stages of forest litter decomposition as affected by nitrogen addition

The effects of nitrogen （N） availability and tree species on the dynamics of carbon and nitrogen at early stage of decomposition of forest litter were studied in a 13-week laboratory incubation experiment. Fresh litter samples including needle litter （Pinus koraiensis） and two types of broadleaf litters （Quercus mongolica and Tilia amurensis） were collected from a broadleaf-korean pine mixed forest in the northern slope of Changbai Mountain （China）. Different doses of N （equal to 0, 30 and 50 kg.ha^-1yr^-1, respectively, as NH4NO3） were added to litter during the experiment period. The litter decomposition rate expressed as mass loss and respiration rate increased significantly with increasing N availability. The mass loss and cumulative CO2-C emission were higher in leaf litter compared to that in needle litter. The dis- solved organic Carbon （DOC） concentrations in litter leachate varied widely between the species, but were not greatly affected by N treatments. Regardless of the N addition rate, both N treatments and species had no significant effect on dissolved organic N （DON） concentrations in litter leachate. About 52-78% of added N was retained in the litter. The percentage of N retention was positively correlated （R^2=0.9 1, p〈0.05） with the litter mass loss. This suggested that a forest floor with easily decomposed litter might have higher potential N sink strength than that with more slowly decomposed litter.

Biomimetic asymmetric Michael addition reactions in water catalyzed by amino-containing β-cyclodextrin derivatives

Nineβ‐cyclodextrin derivatives containing an amino group were synthesized via nucleophilic sub‐stitution from mono（6‐O‐p‐tolylsulfonyl）‐β‐cyclodextrin and used in asymmetric biomimetic Mi‐chael addition reactions in water at room temperature. The mechanism responsible for the moder‐ate activity and enantioselectivity of the β‐cyclodextrin derivatives was explored using nuclear magnetic resonance spectroscopy, namely 2D 1H rotating‐frame overhauser effect spectroscopy （ROESY）, ultraviolet absorption spectroscopy, and quantum chemical calculations, which provide a useful technique for investigating the formation of inclusion complexes. The effects of the pH of the reaction medium, theβ‐cyclodextrin derivative dosage, the structure of the modifying amino group, and various substrates on the yield and enantioselectivity were investigated. The results indicated that these factors had an important effect on the enantiomeric excess （ee） in the reaction system. Experiments using a competitor for inclusion complex formation showed that a hydrophobic cavity is necessary for enantioselective Michael addition. A comparison of the reactions using 4‐nitro‐β‐nitrostyrene and 2‐nitro‐β‐nitrostyrene showed that steric hindrance improved the enan‐tioselectivity. This was verified by the optimized geometries obtained from quantum chemical cal‐culations. An ee of 71%was obtained in the asymmetric Michael addition of cyclohexanone and 2‐nitro‐β‐nitrostyrene, using （S）‐2‐aminomethylpyrrolidine‐modified β‐CD as the catalyst, in an aqueous buffer solution, i.e., CH3COONa‐HCl （pH 7.5）.

Effects of Y addition on structural and mechanical properties of CuZrAl bulk metallic glass

The effects of Y addition on the structural and mechanical properties of CuZrAl bulk metallic glass（BMG） were studied.The results show that the glass forming ability of CuZrAl system is improved by the addition of Y and the fracture strength decreases with Y addition due to the reduction of binding energy induced by Y.The fracture surface is dominated by vein-like patterns in Cu45Zr48Al7 bulk metallic glass,and changes to smooth regions in Cu46Zr42Al7Y5 BMG.TEM observation shows that Cu45Zr48Al7 BMG has a composite microstructure of nanocrystalline phases dispersed in amorphous matrix.However,the Cu46Zr42Al7Y5 BMG shows a fully amorphous structure.

Effects of Cu addition on microstructure and mechanical properties of as-cast magnesium alloy ZK60

The effects of Cu addition on the microstructure and mechanical properties of the as-cast magnesium alloy ZK60 were investigated with optical microscope, SEM, TEM, XRD, EPMA and tensile tester. The mechanism by which the mechanical properties are affected by Cu addition was discussed. The results show that Cu can effectively eliminate the intragranular solute segregations in the alloy, and the grain size of the alloy is decreased considerably with increasing the Cu amount. A ternary eutectic phase MgZnCu with a face-centered cubic structure is identified in the Cu-bearing alloys, which predominantly distributes at the grain boundary and acts as the nucleation sites of microcracks during the plastic deformation process. It is also found that the tensile properties of the alloy firstly increase by the trace addition of 0.5%-1%Cu and then decrease by a further addition up to 2.0%.

Microstructure and tensile properties of AE42-based magnesium alloys with calcium addition

The as-cast microstructure of AE42 was of typical dendritic and composed of the a matrix and some needle-shaped interphases Al11RE3. A small mount of Ca addition results in significant microstructural refinement and formation of a Al2Ca phase, which showed two kinds of morphologies, lamellar and tiny granular. The former distributes on grain boundaries and the later is within the matrix grains. With the increase of Ca addition the volume fraction of Al-RE compound (Al11RE3) decreases, but Al2Ca increases. Addition of Ca causes a significant increase of yield strength of the alloy both at ambient and elevated temperatures, but a little decrease of the ductility. With calcium addition the ultimate strength decreases at ambient temperature and 150°t, but increases at 175°C and 200°C.

Effect of minor-addition of Fe on structural and mechanical properties of CuZrAl bulk metallic glass

The CuZrAl bulk metallic glass with minor-addition of Fe was prepared by rapid quenching method. The structures were examined by X-ray diffraction （XRD）. The effect of Fe on the glass-forming ability was studied by differential scanning calorimetry （DSC）. The minor-addition of Fe obviously extends the supercooled liquid region ΔTx. The plastic strain of the Cu44Zr48Al7Fe bulk metallic glass is about 1.5%. The microstructures were examined by transmission electron microscopy （TEM）. It is found that when 1%-2% Fe （mole fraction） were introduced into the CuZrAl alloy matrix, nanoscale phase separation occurs in the as-prepared Cu44Zr48Al7Fe bulk metallic glass.

基于ASP-SERes2Net的说话人识别算法

为提升说话人识别的特征提取能力,解决在噪声环境下识别率低的问题,提出一种基于残差网络的说话人识别算法——ASP-SERes2Net。首先,采用梅尔语谱图作为神经网络的输入;其次,改进Res2Net网络的残差块,并且在每个残差块后引入压缩激活(squeeze-and-excitation,SE)注意力模块;然后,用注意力统计池化(attention statistics pooling,ASP)代替原来的平均池化;最后,采用附加角裕度的Softmax(additive angular margin Softmax,AAM-Softmax)对说话人身份进行分类。通过实验,将ASP-SERes2Net算法与时延神经网络(time delay neural network,TDNN)、ResNet34和Res2Net进行对比,ASP-SERes2Net算法的最小检测代价函数(minimum detection cost function,MinDCF)值为0.0401,等误率(equal error rate,EER)为0.52%,明显优于其他3个模型。结果表明,ASP-SERes2Net算法性能更优,适合应用于噪声环境下的说话人识别。

不同添加物对鱼糜凝胶品质的影响及其降尿酸潜在作用评价

为开发高品质的功能性鱼糜制品,以白鲢鱼糜为原料,探究外源添加物(荷叶粉、荷叶水提物、玉米须粉、玉米须水提物、百合粉及百合水提物)对鱼糜凝胶品质的影响及其降尿酸潜在作用。结果表明,不同外源添加物能够不同程度地影响鱼糜凝胶品质,其中,荷叶粉和玉米须粉可显著提高鱼糜凝胶的持水性(P<0.05),荷叶粉、百合水提物及荷叶水提物可显著提高鱼糜凝胶强度(P<0.05)。外源添加物可显著改变鱼糜凝胶的风味与滋味特征,使其风味更加浓郁。同时,与对照组相比,添加外源物质均能够显著增加鱼糜凝胶的黄嘌呤氧化酶体外抑制活性(P<0.05),赋予鱼糜凝胶更高的降尿酸潜力。

激光技术在食品3D打印中的应用及发展趋势

随着食品3D打印技术的快速发展,各种辅助技术与其结合的创新应用越来越受关注。激光技术具有精确、高能量和快速实现材料成型等特点,与食品3D打印技术的个性化定制优势高度契合,两者的结合在食品加工领域展现出巨大的应用前景。本文在介绍食品3D打印技术和激光技术发展现状的基础上,着重阐述激光技术在食品3D打印中的应用,包括激光参数(如波长、功率、脉冲等)和工艺优势。同时,指出激光技术在食品3D打印应用中所面临的挑战,如激光照射下的食品安全、应用局限等问题。最后,对激光技术和食品3D打印技术深度融合的发展趋势进行总结与展望,指明未来发展方向,为激光技术在食品3D打印领域的创新应用提供理论参考。