Wettability Gradient-Induced Diode:MXene-Engineered Membrane for Passive-Evaporative Cooling

Thermoregulatory textiles,leveraging high-emissivity structural materials,have arisen as a promising candidate for personal cooling management;however,their advancement has been hindered by the underperformed water moisture transportation capacity,which impacts on their thermophysiological comfort.Herein,we designed a wettability-gradient-induced-diode(WGID)membrane achieving by MXene-engineered electrospun technology,which could facilitate heat dissipation and moisture-wicking transportation.As a result,the obtained WGID membrane could obtain a cooling temperature of 1.5℃ in the“dry”state,and 7.1℃ in the“wet”state,which was ascribed to its high emissivity of 96.40%in the MIR range,superior thermal conductivity of 0.3349 W m^(-1) K^(-1)(based on radiation-and conduction-controlled mechanisms),and unidirectional moisture transportation property.The proposed design offers an approach for meticulously engineering electrospun membranes with enhanced heat dissipation and moisture transportation,thereby paving the way for developing more efficient and comfortable thermoregulatory textiles in a high-humidity microenvironment.

Surface activation of viscose textiles via air,argon,and oxygen dielectric barrier discharge plasma:influence of peak voltage

This paper discusses the use of atmospheric pressure dielectric barrier discharge(DBD)plasma treatment to enhance the surface qualities of viscose fabrics.The study explores the effects of different plasma gases,discharge voltages,and exposure times on the treated fabrics.The findings emphasize the importance of optimizing the plasma's peak voltage to achieve the desired surface treatment outcomes.The document also presents data on colour strength,wettability,colour fastness,and tensile strength of the treated fabrics,as well as scanning electron microscopy(SEM)analysis of surface morphology and chemical analysis using fouriertransition infrared spectroscopy(FTIR)and energy dispersive X-ray(EDX).The results show that treatment at a peak voltage of 11.83 k V is more efficient,except for the tensile strength which is enhanced at a peak voltage of 8.92 k V.The oxygen plasma treatment significantly improves the colour strength,which exhibits an increase from 11 to 18.The intensified colour was attributed to the significant influence of electrostatic interactions between the charged hydroxyl groups of the oxygen plasma treated viscose textiles and the dye molecules,which enhance the printability.The oxygen DBD plasma exhibits a higher ability to enhance the properties of textiles when compared to air and argon plasmas.This study presents a sustainable,economical,secure,and ecologically friendly approach to explore new fabrics for specific uses.

Experimental investigation into effects of the natural polymer and nanoclay particles on the EOR performance of chemical flooding in carbonate reservoirs

This paper aims to investigate the tragacanth gum potential as a natural polymer combined with natural clay mineral(montmorillonite,kaolinite,and illite)nanoparticles(NPs)to form NP-polymer suspension for enhanced oil recovery(EOR)in carbonate reservoirs.Thermal gravimetric analysis(TGA)tests were conducted initially in order to evaluate the properties of tragacanth gum.Subsequently,scanning electron microscopy(SEM)and energy-dispersive X-ray(EDX)tests were used to detect the structure of clay particles.In various scenarios,the effects of natural NPs and polymer on the wettability alteration,interfacial tension(IFT)reduction,viscosity improvement,and oil recovery were investigated through contact angle system,ring method,Anton Paar viscometer,and core flooding tests,respectively.The entire experiment was conducted at 25,50,and 75℃,respectively.According to the experimental results,the clay minerals alone did not have a significant effect on viscosity,but the addition of minerals to the polymer solution leads to the viscosity enhancement remarkably,resulting mobility ratio improvement.Among clay NPs,the combination of natural polymer and kaolinite results in increased viscosity at all temperatures.Considerable wettability alteration was also observed in the case of natural polymer and illite NPs.Illite in combination with natural polymer showed an ability in reducing IFT.Finally,the results of displacement experiments revealed that the combination of natural polymer and kaolinite could be the best option for EOR due to its substantial ability to improve the recovery factor.

A new interacting capillary bundle model on the multiphase flow in micropores of tight rocks

Surfactants are widely used in the fracturing fluid to enhance the imbibition and thus the oil recovery rate. However, current numerical models cannot capture the physics behind capillary imbibition during the wettability alteration by surfactants. Although the interacting capillary bundle(ICB) model shows potential in characterizing imbibition rates in different pores during wettability alteration, the existing ICB models neglect the influence of wettability and viscosity ratio on the imbibition behavior, making it difficult to accurately describe the oil-water imbibition behavior within the porous media. In this work,a new ICB mathematical model is established by introducing pressure balance without assuming the position of the leading front to comprehensively describe the imbibition behavior in a porous medium under different conditions, including gas-liquid spontaneous imbibition and oil-water imbibition.When the pore size distribution of a tight rock is known, this new model can predict the changes of water saturation during the displacement process in the tight rock, and also determine the imbibition rate in pores of different sizes. The water saturation profiles obtained from the new model are validated against the waterflooding simulation results from the CMG, while the imbibition rates calculated by the model are validated against the experimental observations of gas-liquid spontaneous imbibition. The good match above indicates the newly proposed model can show the water saturation profile at a macroscopic scale while capture the underlying physics of the multiphase flow in a porous medium at a microscopic scale. Simulation results obtained from this model indicate that both wettability and viscosity ratio can affect the sequence of fluid imbibition into pores of different sizes during the multiphase flow, where less-viscous wetting fluid is preferentially imbibed into larger pores while more-viscous wetting fluid tends to be imbibed into smaller pores. Furthermore, this model provides an avenue to calculate the imbibition rate in pores of different sizes during wettability alteration and capture the non-Darcy effect in micro-and nano-scale pores.

Wettability,reactivity,and interface structure in Mg/Ni system

The sessile drop method was applied to the experimental investigation of the wetting and spreading behaviors of liquid Mg drops on pure Ni substrates.For comparison,the experiments were performed in two variants:(1)using the Capillary Purification(CP)procedure,which allows the non-contact heating and squeezing of a pure oxide-free Mg drop;(2)by classical Contact Heating(CH)procedure.The high-temperature tests were performed under isothermal conditions(CP:760℃for 30 s;CH:715℃for 300 s)using Ar+5 wt%H_(2) atmosphere.During the sessile drop tests,images of the Mg/Ni couples were recorded by CCD cameras(57 fps),which were then applied to calculate the contact angles of metal/substrate couples.Scanning and transmission electron microscopy analyses,both coupled with energy-dispersive X-ray spectroscopy,were used for detailed structural characterization of the solidified couples.It was found that an oxide-free Mg drop obtained by the CP procedure showed a wetting phenomenon on the Ni substrate(an average contact angleθ<90°in<1 s),followed by fast spreading and good wetting over the Ni substrate(θ_((CP))~20°in 5 s)to form a final contact angle ofθ_(f(CP))~18°.In contrast,a different wetting behavior was observed for the CH procedure,where the unavoidable primary oxide film on the Mg surface blocked the spreading of liquid Mg showing apparently non-wetting behavior after 300 s contact at the test temperature.However,in both cases,the deep craters formed in the Ni substrates under the Mg drops and significant change in the structure of initially pure Mg drops to Mg-Ni alloys suggest a strong dissolution of Ni in liquid Mg and apparent values of the final contact angles measured for the Mg/Ni system.

On the spreading behavior of a droplet on a circular cylinder using the lattice Boltzmann method

The study of a droplet spreading on a circular cylinder under gravity was carried out using the pseudo-potential lattice Boltzmann high-density ratios multiphase model with a non-ideal Peng–Robinson equation of state. The calculation results indicate that the motion of the droplet on the cylinder can be divided into three stages: spreading, sliding, and aggregating.The contact length and contact time of a droplet on a cylindrical surface can be affected by factors such as the wettability gradient of the cylindrical wall, the Bond number, and droplet size. Furthermore, phase diagrams showing the relationship between Bond number, cylinder wall wettability gradient, and contact time as well as maximum contact length for three different droplet sizes are given. A theoretical foundation for additional research into the heat and mass transfer process between the droplet and the cylinder can be established by comprehending the variable rules of maximum contact length and contact time.

Nuclear magnetic resonance experiments on the time-varying law of oil viscosity and wettability in high-multiple waterflooding sandstone cores

A simulated oil viscosity prediction model is established according to the relationship between simulated oil viscosity and geometric mean value of T2spectrum,and the time-varying law of simulated oil viscosity in porous media is quantitatively characterized by nuclear magnetic resonance(NMR)experiments of high multiple waterflooding.A new NMR wettability index formula is derived based on NMR relaxation theory to quantitatively characterize the time-varying law of rock wettability during waterflooding combined with high-multiple waterflooding experiment in sandstone cores.The remaining oil viscosity in the core is positively correlated with the displacing water multiple.The remaining oil viscosity increases rapidly when the displacing water multiple is low,and increases slowly when the displacing water multiple is high.The variation of remaining oil viscosity is related to the reservoir heterogeneity.The stronger the reservoir homogeneity,the higher the content of heavy components in the remaining oil and the higher the viscosity.The reservoir wettability changes after water injection:the oil-wet reservoir changes into water-wet reservoir,while the water-wet reservoir becomes more hydrophilic;the degree of change enhances with the increase of displacing water multiple.There is a high correlation between the time-varying oil viscosity and the time-varying wettability,and the change of oil viscosity cannot be ignored.The NMR wettability index calculated by considering the change of oil viscosity is more consistent with the tested Amott(spontaneous imbibition)wettability index,which agrees more with the time-varying law of reservoir wettability.

Effect of phosphorus content on interfacial heat transfer and film deposition behavior during the high-temperature simulation of strip casting

The interfacial wettability and heat transfer behavior are crucial in the strip casting of high phosphorus-containing steel.A hightemperature simulation of strip casting was conducted using the droplet solidification technique with the aims to reveal the effects of phosphorus content on interfacial wettability,deposited film,and interfacial heat transfer behavior.Results showed that when the phosphorus content increased from 0.014wt%to 0.406wt%,the mushy zone enlarged,the complete solidification temperature delayed from1518.3 to 1459.4℃,the final contact angle decreased from 118.4°to 102.8°,indicating improved interfacial contact,and the maximum heat flux increased from 6.9 to 9.2 MW/m2.Increasing the phosphorus content from 0.081wt%to 0.406wt%also accelerated the film deposition rate from 1.57 to 1.73μm per test,resulting in a thickened naturally deposited film with increased thermal resistance that advanced the transition point of heat transfer from the fifth experiment to the third experiment.

Modeling of multiphase flow in low permeability porous media:Effect of wettability and pore structure properties

Multiphase flow in low permeability porous media is involved in numerous energy and environmental applications.However,a complete description of this process is challenging due to the limited modeling scale and the effects of complex pore structures and wettability.To address this issue,based on the digital rock of low permeability sandstone,a direct numerical simulation is performed considering the interphase drag and boundary slip to clarify the microscopic water-oil displacement process.In addition,a dual-porosity pore network model(PNM)is constructed to obtain the water-oil relative permeability of the sample.The displacement efficiency as a recovery process is assessed under different wetting and pore structure properties.Results show that microscopic displacement mechanisms explain the corresponding macroscopic relative permeability.The injected water breaks through the outlet earlier with a large mass flow,while thick oil films exist in rough hydrophobic surfaces and poorly connected pores.The variation of water-oil relative permeability is significant,and residual oil saturation is high in the oil-wet system.The flooding is extensive,and the residual oil is trapped in complex pore networks for hydrophilic pore surfaces;thus,water relative permeability is lower in the water-wet system.While the displacement efficiency is the worst in mixed-wetting systems for poor water connectivity.Microporosity negatively correlates with invading oil volume fraction due to strong capillary resistance,and a large microporosity corresponds to low residual oil saturation.This work provides insights into the water-oil flow from different modeling perspectives and helps to optimize the development plan for enhanced recovery.

Synthesis of CA_(6)/AlON composite with enhanced slag resistance

Different amounts of AlON have been introduced in calcium hexaaluminate(CA_(6)) using two approaches, that is, one-step and twostep methods, to improve the slag resistance of CA_(6). A one-step method can directly sinter the mixtures combining Al_(2)O_(3), CaCO_(3), and Al in flowing nitrogen, in which AlON clusters are always formed because of the poor wettability of Al by Al_(2)O_(3), leading to the high porosity of CA_(6)/AlON composite. In a two-step method, CA_(6)and AlON are prepared separately and then mixed and sintered in flowing nitrogen. Compared with the sample prepared by the one-step method, CA_(6)and AlON in composite by the two-step method are more uniformly distributed,and the optimized amount of AlON added is 10wt%. The slag corrosion and penetration test shows that the CA_(6)/AlON composite using the two-step method exhibits superior slag corrosion protection. The promoted effect of AlON on slag penetration and corrosion resistance is also discussed.

Wettability of different clay mineral surfaces in shale:Implications from molecular dynamics simulations

Shale contains a lot of clay minerals. Clay minerals mainly exist in nano- and micro-meter sized particles, and the pore structure is complex, which leads to its extremely complex wettability. The surface wettability of clay minerals significantly affects the oil and gas-bearing capacity of shale reservoirs. Therefore, studying the wettability of common clay minerals in shale at the nanoscale is of great significance for shale hydrocarbon exploration and development. In this study, the wetting behavior of water in n-hexane and toluene on different clay mineral surfaces at the nanoscale was systematically studied using Molecular dynamics (MD) simulation. And the influencing factors of wettability were analyzed. Through the analysis of the morphological changes of water, relative concentration of water, RDF and interaction energy, it is concluded that the following order of water wettability on the surfaces of clay minerals: montmorillonite > chlorite > kaolinite > illite. Through the analysis of interaction energy, it is concluded that the hydrophilicity of four clay minerals is stronger than that of lipophilicity. And the main interactions between water and oil and the mineral surfaces were van der Waals force and electrostatic force. In addition, the temperature, liquid hydrocarbon type, and mineralization of water affected the wettability of clay minerals. The concentration of water on the surfaces of montmorillonite, kaolinite, and illite decreased with increasing temperature, and the water wettability decreased. At 298 K, the hydrophilicity of the surfaces of the clay minerals in toluene follows the order montmorillonite > chlorite > kaolinite > illite. The higher the NaHCO3 concentration in water, the weaker the wettability of the clay mineral surfaces to water. By comparing the previous experimental results with the MD simulation results, similar wetting characteristics were obtained, and the reliability of the simulation results was verified. MD simulation was used to explore the water wetting of the surfaces of four clay minerals in a shale reservoir from the micro level. This makes up for the lack of experimental means for clarifying the flow and production mechanisms of shale oil and gas and effectively improves the evaluation technology of shale.

Effects of channel wall wettability on gas-liquid dynamics mass transfer under Taylor flow in a serpentine microchannel

The wall wettability of microchannels plays an important role in the gas-liquid mass transfer dynamics under Taylor flow.In this study,we regulated the contact angle of the wall surface through surface chemical grafting polymerization under controlled experimental conditions.The dynamic changes of CO_(2)bubbles flowing along the microchannel were captured by a high-speed video camera mounted on a stereo microscope,whilst a unit cell model was employed to theoretically investigate the gas-liquid mass transfer dynamics.We quantitatively characterized the effects of wall wettability,specifically the contact angle,on the formation mechanism of gas bubbles and mass transfer process experimentally.The results revealed that the gas bubble velocity,the overall volumetric liquid phase mass transfer coefficients(kLa),and the specific interfacial area(a)all increased with the increase of the contact angle.Conversely,gas bubble length and leakage flow decreased.Furthermore,we proposed a new modified model to predict the gas-liquid two-phase mass transfer performance,based on van Baten’s and Yao’s models.Our proposed model was observed to agree reasonably well with experimental observations.

Evaluation of the coupled impact of silicon oxide nanoparticles and low-salinity water on the wettability alteration of Berea sandstones

This study investigated experimentally the coupled effects of hydrophilic SiO_(2) nanoparticles(NPs)and low-salinity water(LSW)on the wettability of synthetic clay-free Berea sandstone.Capillary pressure,interfacial tension(IFT),contact angle,Zeta potential,and dynamic displacement measurements were performed at various NP mass fractions and brine salinities.The U.S.Bureau of Mines(USBM)index was used to quantify the wettability alteration.Furthermore,the NP stability and retention and the effect of enhanced oil recovery by nanofluid were examined.The results showed that LSW immiscible displacement with NPs altered the wettability toward more water wet.With the decreasing brine salinity and increasing NP mass fraction,the IFT and contact angle decreased.The wettability alteration intensified most as the brine salinity decreased to 4000 mg/L and the NP mass fraction increased to 0.075%.Under these conditions,the resulting incremental oil recovery factor was approximately 13 percentage points.When the brine salinity was 4000 mg/L and the NP mass fraction was 0.025%,the retention of NPs caused the minimum damage to permeability.

A potential NMR-based wettability index using free induction decay for rocks

The wettability of reservoir rocks saturated with oil and water is one of the most important factors influencing petrophysics and oil recovery.Minerals with different wettability constitute the overall heterogeneous wettability in rocks.Variations in sample composi-tion can be detected by nuclear magnetic resonance(NMR)measurements.In this paper,the method of using the magnetic susceptibility contrast between rock skeleton and saturated fluid to estimate wettability is proposed.The theoretical feasibility was firstly analyzed,and then the internal gradients caused by magnetic susceptibility contrasts were employed to interpret wettability alteration before and after ageing process in rocks.It was discovered that water and oil in the same pores experienced different internal gradients after ageing,which were associated with the differences in magnetic susceptibility con-trasts.After that,the free induction decay measurement was performed to acquire mag-netic susceptibility contrasts of artificial sandstone samples with the intermediate-wet condition.A refined NMR wettability index was presented and correlated with the Amott wettability tests.The experimental results demonstrate that the new method for deter-mining wettability is feasible.

Nanofluid based on 1-dodecylpyridinium chloride for enhanced oil recovery

The use of nanoparticles is considered promising for enhanced oil recovery(EOR),especially when they are combined with surfactants.However,the combination of nano-sized material with surface-active ionic liquids(SAILs)is an unexplored EOR method.In this work,the advantages of mixing Al2O3 nanoparticles with the SAIL 1-dodecylpyridinium chloride were investigated.Stable nanofluids in brine could only be achieved using the polymer polyvinylpyrrolidone(PVP)as a stabilizing agent.It was found that the addition of nanoparticles(and PVP)to the surfactant formulation helped to:slightly increase its viscosity,enhance its water-oil interfacial tension(IFT)reduction capacity,and reduce the adsorption on carbonate rocks(adsorption on sandstone was found to be excessive).IFT was selected as target property to minimize for the design of EOR formulations.Core flooding tests were carried out with surfactant(0.5 wt%[C_(12)py]Cl),surfactant-polymer(0.5 wt%[C_(12)py]Cl,1.0 wt%PVP)and nanofluid(0.05 wt%Al_(2)O_(3),1.0 wt%PVP,0.5 wt%[C12py]Cl)formulations in brine(0.5 wt%NaCl).Additional oil recoveries of 3.4%,7.4%and 12.0%OOIP were achieved,respectively,the nanofluid formulation being the most promising for the application.Moreover,it was found capable of changing the wettability of carbonate rocks from oilwet to intermediate-wet.The significance of this work lies in showing the new possibilities resulting from the combination of SAILs and nanoparticles for EOR,specifically the combination of[C_(12)py]Cl with Al_(2)O_(3).

Wettability alteration of organo-vermiculites induced by layer charge and tailored bis-N-heterocyclic quaternary ammonium salts

Wettability is an important surface property that deserves to further explore the factors on its alteration.Series of bis-N-heterocyclic quaternary ammonium salts with different spacer length and N-heterocyclic headgroups(morpholinium(BMMB,BMMD and BMMH),piperidinium(BPMH)and piperazinium(BMPMH))have been synthesized and employed for altering the wettability of vermiculite and its derivates(Vts)treated by Li^(+)-saturated heating method.The results of X-ray diffraction(XRD),Fourier transform infrared spectroscopy(FT-IR),thermogravimetric analysis(TG-DTG),scanning electron microscopy(SEM)and N_(2)adsorption/desorption isotherms indicate that all of the bis-N-heterocyclic quaternary ammonium salts have been successfully inserted into the vermiculite layers,leading to the organic monolayer.The results of capillary rise tests combined with Lipophilic to Hydrophilic Ratio(LHR)values unveil the wettability alteration of the organo-Vts.As the layer charge decreases,the hydrophilicity of the organo-Vts gradually increases,which is probably caused by the decline in binding sites.As the result of the change in spacer length of modifier,the wetting properties of morpholinium-based organo-Vts change in order of BMMD-Vts>BMMH-Vts>BMMB-Vts,and difference in N-heterocyclic headgroups leads to the sequence of wettability:BMPMH-Vts>BPMH-Vts>BMMH-Vts.Layer charge of Vt,spacer length and the type of the N-heterocyclic headgroup of modifier have the synergistic effect on the regulation of the wettability.

Impact of surface roughness,surface charge,and temperature on sandstone wettability alteration by nanoparticles

The wettability of rocks affects the balance between capillary and viscous forces during multiphase flow through porous media,which in turn determines the fluid displacement process governing the recovery of oil from subsurface formations.In this work,the mechanism of wettability reversal of aged synthetic sandstones by metal oxide nanoparticles(SiO_(2) and Al_(2)O_(3))was investigated with particular focus on the impact of surface roughness,zeta potential,and temperature.The synthetic surfaces were prepared from powders of Berea sandstone with known grain size ranges and their average roughness and roughness ratio were obtained from the 3D surface reconstruction of their microscope images.Each surface was subsequently aged in Permian crude oil to alter its wettability.For surfaces with larger grain sizes and lower surface roughness ratios,the lower capillary pressure allowed stronger oil/surface interactions,leading to enhanced oil-wetness.The wettability alteration effects of nanoparticles were then examined through real-time top view imaging and dynamic front view contact angle experiments.The negatively charged SiO_(2) nanoparticles rapidly reversed the sandstone wettability,indicating their potential applicability as wettability alteration agents.By contrast,the positively charged Al_(2)O_(3) counterpart caused no wettability reversal.The mechanism of wettability alteration was further studied by microscale interaction analyses and nanoscale transmission electron microscopy.Because nanoparticles were only a few nanometers large,the microscale roughness had a negligible effect on the wettability reversal.Instead,the combined effect of van der Waals dispersion forces and surface-charge-induced electrostatic forces were recognized as the two key factors affecting the wettability of sandstone particles.Such interactions may be curbed at elevated temperatures due to a decrease in the zeta potential and colloidal stability of the particles.

Molecular design and applications of a nanostructure green Tripodal surface active ionic liquid in enhanced oil recovery: Interfacial tension reduction, wettability alteration, and emulsification

Surface active ionic liquids (SAILs) are considered as prominent materials in enhanced oil recovery thanks to their high interfacial activity. This study reports the preparation and applications of a nanostructure Tripodal imidazolium SAIL as an environmentally-friendly substitute to the conventional surfactants. The product has a star-like molecular structure centered by a triazine spacer, namely [(C_(4)im)_(3)TA][Cl_(3)], prepared by a one-step synthesis method and characterized with FT-IR, NMR, XRD, and SEM analysis methods. The interfacial tension of the system was decreased to about 78% at critical micelle concentration of less than 0.08 mol·dm^(−3). Increasing temperature, from 298.2 to 323.2 K, improved this capability. The solid surface wettability was changed from oil-wet to water-wet and 80% and 77% stable emulsions of crude oil–aqueous solutions were created after one day and one week, respectively. Compared to the Gemini kind homologous SAILs, the superior effects of the Tripodal SAIL were revealed and attributed to the strong hydrophobic branches in the molecule. The Frumkin adsorption isotherm precisely reproduced the generated IFT data, and accordingly, the adsorption and thermodynamic parameters were determined.

High-frequency supercapacitors with phosphorus-doped Ketjen black

Compact supercapacitors(SCs)have attracted attention for their great potential to replace bulky aluminum electrolytic capacitors(AECs)in alternating current(AC)line filtering applications.Herein,the fabrication of a high-frequency SC is reported using Ketjen black(KB)nanoparticles doped with phosphorus(P)to achieve a high areal capacitance of up to 2.26 mF cm^(-2)along with a high-rate capability,with a phase angle of-80.2°at 120 Hz.The high performance of the phosphorus-doped KB(designated PKB)SC with a 6 M KOH aqueous electrolyte is associated with its increased surface wettability and additional capacitive sites provided by the P-doping.Density functional theory(DFT)calculations further indicate that the P-doping enhances the interactions between the electrolyte ions and the carbon surface,thus leading to an improved electrochemical performance.These results suggest that the P-doped carbonbased SC could be highly favored in replacing conventional AECs in various high-frequency electronic devices.

Reduction of ice adhesion on nanostructured and nanoscale slippery surfaces

Ice nucleation and accretion on structural surfaces are sources of major safety and operational concerns in many industries including aviation and renewable energy.Common methods for tackling these are active ones such as heating,ultrasound,and chemicals or passive ones such as surface coatings.In this study,we explored the ice adhesion properties of slippery coated substrates by measuring the shear forces required to remove a glaze ice block on the coated substrates.Among the studied nanostructured and nanoscale surfaces[i.e.,a superhydrophobic coating,a fluoropolymer coating,and a polydimethylsiloxane(PDMS)chain coating],the slippery omniphobic covalently attached liquid(SOCAL)surface with its flexible polymer brushes and liquid-like structure significantly reduced the ice adhesion on both glass and silicon surfaces.Further studies of the SOCAL coating on roughened substrates also demonstrated its low ice adhesion.The reduction in ice adhesion is attributed to the flexible nature of the brush-like structures of PDMS chains,allowing ice to detach easily.