Sensitivity Analysis of Electromagnetic Scattering from Dielectric Targets with Polynomial Chaos Expansion and Method of Moments

In this paper,an adaptive polynomial chaos expansion method(PCE)based on the method of moments(MoM)is proposed to construct surrogate models for electromagnetic scattering and further sensitivity analysis.The MoM is applied to accurately solve the electric field integral equation(EFIE)of electromagnetic scattering from homogeneous dielectric targets.Within the bistatic radar cross section(RCS)as the research object,the adaptive PCE algorithm is devoted to selecting the appropriate order to construct the multivariate surrogate model.The corresponding sensitivity results are given by the further derivative operation,which is compared with those of the finite difference method(FDM).Several examples are provided to demonstrate the effectiveness of the proposed algorithm for sensitivity analysis of electromagnetic scattering from homogeneous dielectric targets.

Discussion on the application prospect of the transient electromagnetic method based on the dual launcher and mine advanced detection

The dual transmitter implements the equivalent anti-magnetic flux transient electromagnetic method, which can effectively reduce the scope of the transient electromagnetic detection blind area. However, this method is rarely reported in the detection of pipelines in urban geophysical exploration and the application of coal mines. Based on this, this paper realizes the equivalent anti-magnetic flux transient electromagnetic method based on the dual launcher. The suppression effect of this method on the blind area is analyzed by physical simulation. And the detection experiment of underground pipelines is carried out outdoors. The results show that the dual launcher can significantly reduce the turn-off time, thereby effectively reducing the impact of the blind area on the detection results, and the pipeline detection results verify the device’s effectiveness. Finally, based on the ground experimental results, the application prospect of mine advanced detection is discussed. Compared with other detection fields, the formation of blind areas is mainly caused by the equipment. If the dual launcher can be used to reduce the blind area, the accuracy of advanced detection can be improved more effectively. The above research results are of great significance for improving the detection accuracy of the underground transient electromagnetic method.

Corrigendum to“Atomic-scale electromagnetic theory bridging optics in microscopic world and macroscopic world”

The signs of the electric field markers in Figs.2 and 4 of the paper[Chin.Phys.B 32104211(2023)]have been corrected.These modifications do not affect the results derived in the paper.

Application of SPAC method and electromagnetic wave CT in karst detection of Wuhan Metro Line 8

In recent years,karst construction projects in the built-up area of Wuhan(capital of Hubei Province,China)are increasing,and the karst geological disasters have aroused social concerns.The actual engineering projects usually use shallow geophysical exploration methods to explore karst.This paper uses Spatial Auto-Correlation Method(SPAC)and electromagnetic Computerized Tomography(CT)to detect karst in urban built-up areas.Depending on the different physical properties of rock and soil,the SPAC method can better reveal the interface between soil and rock strata and the interface between soil layers.The electromagnetic CT method can identify strata according to the apparent absorption coefficient,which can better reveal the interface between soil and rock,the interface between the more intact and weathered rock.The SPAC method is mainly qualitative to measure the low-speed area,namely,the wrong geological body i.e.,karst cave,but also can detect the fracture zone or filling mode of karst cave,and at the same time,cannot use exploration holes or logging observation.The electromagnetic CT method can accurately detect the location and scale of the karst caves and has a higher accuracy detecting karst bands.In addition,exploration holes or well logging observations are also expected to be conducted,and their detection effect is greatly affected by lithology.

3D forward modeling and response characteristics of low-resistivity overburden of the CFS-PML absorbing boundary for ground-well transient electromagnetic method

This study used the stable and convergent Dufort-Frankel method to differentially discretize the diffusion equation of the ground-well transient electromagnetic secondary field.The absorption boundary condition of complex frequency-shifted perfectly matched layer(CFS-PML)was used for truncation so that the low-frequency electromagnetic wave can be better absorbed at the model boundary.A typical three-dimensional(3D)homogeneous half-space model was established and a low-resistivity cube model was analyzed under the half-space condition.The response patterns and drivers of the low-resistivity cube model were discussed under the influence of a low-resistivity overburden.The absorption boundary conditions of CFS-PML significantly affected the low-frequency electromagnetic waves.For a low-resistivity cube around the borehole,its response curve exhibited a single-peak,and the extreme point of the curve corresponded to the center of the low-resistivity body.When the low-resistivity cube was directly below the borehole,the response curve showed three extreme values(two high and one low),with the low corresponding to the center of the low-resistivity body.The total field response of the low-resistivity overburden was stronger than that of the uniform half-space model due to the low-resistivity shielding effect of electromagnetic waves.When the receiving-transmitting distance gradually increased,the effect of the low-resistivity overburden was gradually weakened,and the response of the low-resistivity cube was strengthened.It was affected by the ratio of the overburden resistivity to the resistivity of the low-resistivity body.

A finite volume method for global electromagnetic induction forward modeling on collocated unstructured grids

Global electromagnetic induction provides an efficient way to probe the electrical conductivity in the Earth’s deep interior.Owing to the increasing geomagnetic data especially from high-accuracy geomagnetic satellites,inverting the Earth’s three-dimensional conductivity distribution on a global scale becomes attainable.A key requirement in the global conductivity inversion is to have a forward solver with high-accuracy and efficiency.In this study,a finite volume method for global electromagnetic induction forward modeling is developed based on unstructured grids.Arbitrary polyhedral grids are supported in our algorithms to obtain high geometric adaptability.We employ a cell-centered collocated variable arrangement which allows convenient discretization for complex geometries and straightforward implementation of multigrid technique.To validate the method,we test our code with two synthetic models and compare our finite volume results with an analytical solution and a finite element numerical solution.Good agreements are observed between our solution and other results,indicating acceptable accuracy of the proposed method.

Analysis and Simulation of the Influence of Electromagnetic Fields on Living Beings near HV Power Lines Using the FDTD Method

Recent decades have seen rapid advances in the field of electrical engineering, such that our environment has become a sea of electrical and magnetic signals, raising questions about the possible effects of low-frequency electromagnetic fields on the environment and which are capable of modifying and destroying our ecosystem. Particular interest was given in this article due to a massive influx of population living near high voltage lines. The analysis and simulation of the influence of low frequency electromagnetic fields on living beings in the vicinity of high voltage sources 132 kV and 220 kV in urban areas in DR Congo is the subject of our research with a view to estimating the level of exposure of humans to low frequency electromagnetic fields. To carry out our research, we used the classic method of analyzing the field produced near a high voltage line based on Maxwell’s image theory, the Maxwell-Gauss theorem and Maxwell-Ampère theorem to model and quantify low-frequency electromagnetic fields in the vicinity of high-voltage lines. The 2D FDTD numerical formulation was developed from telegraphers’ equations and allowed us to obtain models of current and voltage induced by electromagnetic fields on living beings below and near HV lines. The different simulations carried out on the proposed models illustrate the effects of the electrical and geometric parameters of the pylons on the distribution of the electromagnetic field in the vicinity of the HV lines. The results obtained were compared to the safety limits recommended by the standards.

Mapping coalmine goaf using transient electromagnetic method and high density resistivity method in Ordos City, China

The research about subsurface characteristics by using transient electromagnetic method（TEM） and high density resistivity method（HDRM） were already conducted in Ordos. The objective of this research is to detect coalmine goaf areas based on rock resistivity. The data processing using wavelet transform, three point smoothing, RES2 DINV and Maxwell processing software to obtain 2D resistivity structure. The results showed that the layers with maximum resistivity values（30e33 U m on Line 1, 30e31 U m on Line 2, 32e40 U m on Line3） are founded at station 1e7, and 14e20 on Line 1,13e18 on Line 2, and 8e13 and 16e20 on Line 3 which is predicted as goaf layer, and the minimum resistivity values（20e26 U m of TEM, 45e75 U m of HDRM） at the other layers. This resistivity difference was caused by the geology and characteristics of the study area which is located close by the cleugh with rich coal, so the goaf area distinguishable with aquifer layer and coal seam. The results were also significant accidents and serious destruction of ecological environment.

Multi-dimensional and complicated electromagnetic interference hardware-in-the-loop simulation method

A typical electronic communication system, such as GPS receiver, unmanned aerial vehicle＇s （UAV＇s） data link, and radar, faces multi-dimensional and complicated electromagnetic interference in operating environment. To measure the anti- interference performance of the electronic communication system in the complicated electromagnetic interference environment, a method of multi-dimensional and complicated electromagnetic interference hardware-in-the-loop simulation in an anechoic room is proposed. It takes into account the characteristics of interference signals and the positional relationship among interference, the receiver and the transmitter of the electronic communication system. It uses the grey relational method and the angular domain mapping error correction method to control the relevant parameters, the microwave switch and so on, thus achieving the approximately actual mapping of the outdoor multi-dimensional and complicated electromagnetic interference in the anechoic room. To verify the effectiveness of this method, the multi-dimensional and complicated electromagnetic interference of the UAV＇s data link is simulated as an example. The results show that the degree of correlation between the calculated signal to interference ratio of the data link receiver in the actual scene and the measured signal to interference ratio of the data link receiver simulated with this method in the anechoic room is 0.968 1, proving that the method is effective for simulating the complicated electromagnetic interference.

SIMUUTION OF ELECTROMAGNETIC TUBE BULGING BASED ON LOOSE COUPLING METHOD

A loose coupling method is used to solve the electromagnetic tube bulging. ANSYS/ EMAG is used to model the time varying electromagnetic field with the discharge current used as excitation, in order to obtain the radial and axial magnetic pressure acting on the tube, the magnetic pressure is then used as boundary conditions to model the high velocity deformation of tube with DYNAFORM, The radial magnetic pressure on the tube decreases from the center to the tube end, axial magnetic pressure is greater near the location equal to the coil height and slight in the other region. The radial displacement of deformed workpicces is distributed uniformly near the tube center and decreases from the center to the end; Deformation from the location equal to coil height to the tube end is little. This distribution is consistent with the distribution of radial pressure; Effect of the axial magnetic pressure on deformation can be ignored, The calculated results show well agreements with the experimental results.

3-D Numerical Simulation of the Electromagnetic Dam of Twin Roll Casting using Edge Element Method

The 3-dimension numerical simulation study on the electromagnetic dam used in the twin roll caster has been performed by using the edge element method. It was found that the materials and structures of the roll collars have great influence on the distribution of the magnetic flux density, eddy current density and the electromagnetic force in the molten pool. The conductive collars make the magnetic flux density decreased in the molten pool, but it also makes the magnetic force more uniformly, and the force in the low part of the molten pool where needs greater force have increased some what. The conductive collars make the EMD device more effective than the nonconductive collars.

Atomic-scale electromagnetic theory bridging optics in microscopic world and macroscopic world

Atoms in the microscopic world are the basic building blocks of the macroscopic world. In this work, we construct an atomic-scale electromagnetic theory that bridges optics in the microscopic and macroscopic worlds. As the building block of the theory, we use the microscopic polarizability to describe the optical response of a single atom, solve the transport of electromagnetic wave through a single atomic layer under arbitrary incident angle and polarization of the light beam, construct the single atomic layer transfer matrix for light transport across the atomic layer. Based on this transfer matrix, we get the analytical form of the dispersion relation, refractive index, and transmission/reflection coefficient of the macroscopic medium. The developed theory can handle single-layer and few-layers of homogeneous and heterogeneous 2D materials, investigate homogeneous 2D materials with various vacancies or insertion atomic-layer defects, study compound 2D materials with a unit cell composed of several elements in both the lateral and parallel directions with respect to the light transport.

A Review of Electromagnetic Energy Regenerative Suspension System&Key Technologies

The active suspension has undoubtedly improved the performance of the vehicle,however,the trend of“lowcarbonization,intelligence,and informationization”in the automotive industry has put forward higher and more urgent requirements for the suspension system.The automotive industry and researchers favor active energy regeneration suspension technology with safety,comfort,and high energy regenerative efficiency.In this paper,we review the research progress of the structure form,optimization method,and control strategy of electromagnetic energy regenerative suspension.Specifically,comparing the pros and cons of the existing technology in solving the contradiction between dynamic performance and energy regeneration.In addition,the development trend of electromagnetic energy regenerative suspension in the field of structure form,optimization method,and control technology prospects.

Circuit-field coupled finite element analysis method for an electromagnetic acoustic transducer under pulsed voltage excitation

This paper presents an analytical method for electromagnetic acoustic transducers （EMATs） under voltage excitation and considers the non-uniform distribution of the biased magnetic field. A complete model of EMATs including the non-uniform biased magnetic field, a pulsed eddy current field and the acoustic field is built up. The pulsed voltage excitation is transformed to the frequency domain by fast Fourier transformation （FFT）. In terms of the time harmonic field equations of the EMAT system, the impedances of the coils under different frequencies are calculated according to the circuit-field coupling method and Poynting＇s theorem. Then the currents under different frequencies are calculated according to Ohm＇s law and the pulsed current excitation is obtained by inverse fast Fourier transformation （IFFT）. Lastly, the sequentially coupled finite element method （FEM） is used to calculate the Lorentz force in the EMATs under the current excitation. An actual EMAT with a two-layer two-bundle printed circuit board （PCB） coil, a rectangular permanent magnet and an aluminium specimen is analysed. The coil impedances and the pulsed current are calculated and compared with the experimental results. Their agreement verified the validity of the proposed method. Furthermore, the influences of lift-off distances and the non-uniform static magnetic field on the Lorentz force under pulsed voltage excitation are studied.

Sparsity-based efficient simulation of cluster targets electromagnetic scattering

An efficient and real-time simulation method is proposed for the dynamic electromagnetic characteristics of cluster targets to meet the requirements of engineering practical applications.First,the coordinate transformation method is used to establish a geometric model of the observation scene,which is described by the azimuth angles and elevation angles of the radar in the target reference frame and the attitude angles of the target in the radar reference frame.Then,an approach for dynamic electromagnetic scattering simulation is proposed.Finally,a fast-computing method based on sparsity in the time domain,space domain,and frequency domain is proposed.The method analyzes the sparsity-based dynamic scattering characteristic of the typical cluster targets.The error between the sparsity-based method and the benchmark is small,proving the effectiveness of the proposed method.

Parallel Iterative FEM Solver with Initial Guess for Frequency Domain Electromagnetic Analysis

The finite element method is a key player in computational electromag-netics for designing RF(Radio Frequency)components such as waveguides.The frequency-domain analysis is fundamental to identify the characteristics of the components.For the conventional frequency-domain electromagnetic analysis using FEM(Finite Element Method),the system matrix is complex-numbered as well as indefinite.The iterative solvers can be faster than the direct solver when the solver convergence is guaranteed and done in a few steps.However,such complex-numbered and indefinite systems are hard to exploit the merit of the iterative solver.It is also hard to benefit from matrix factorization techniques due to varying system matrix parts according to frequency.Overall,it is hard to adopt conventional iterative solvers even though the system matrix is sparse.A new parallel iterative FEM solver for frequency domain analysis is implemented for inhomogeneous waveguide structures in this paper.In this implementation,the previous solution of the iterative solver of Matlab(Matrix Laboratory)employ-ing the preconditioner is used for the initial guess for the next step’s solution process.The overlapped parallel stage using Matlab’s Parallel Computing Toolbox is also proposed to alleviate the cold starting,which ruins the convergence of early steps in each parallel stage.Numerical experiments based on waveguide structures have demonstrated the accuracy and efficiency of the proposed scheme.

Finite Volume Time Domain with the Green Function Method for Electromagnetic Scattering in Schwarzschild Spacetime

The finite volume time domain(FVTD) algorithm and Green function algorithm are extended to Schwarzschild spacetime for numerical simulation of electromagnetic scattering. The FVTD method in Schwarzschild spacetime is developed by filling the flat spacetime with an equivalent medium. The Green function in Schwarzschild spacetime is acquired by solving initial value problems. Both the FVTD code and the Green function code are validated by numerical results. Scattering in Schwarzschild spacetime is simulated with these methods.

Application of Transient Electromagnetic Method with Multi-Radiation Field Sources in Deep Edge Mineral Resources Exploration

In recent years,in order to meet the practical needs of deep edge mine detection with large depth and high precision,transient electromagnetic method(TEM)near emission source detection mode has become an international advanced method(Xue et al.,2020).

Method for electromagnetic detection satellites scheduling based on genetic algorithm with alterable penalty coefficient

The electromagnetic detection satellite （EDS） is a type of earth observation satellites （EOSs）. The Information collected by EDSs plays an important role in some fields, such as industry, science and military. The scheduling of EDSs is a complex combinatorial optimization problem. Current research mainly focuses on the scheduling of imaging satellites and SAR satellites, but little work has been done on the scheduling of EDSs for its specific characteristics. A multi-satellite scheduling model is established, in which the specific constrains of EDSs are considered, then a scheduling algorithm based on the genetic algorithm （GA） is proposed. To deal with the specific constrains of EDSs, a penalty function method is introduced. However, it is hard to determine the appropriate penalty coefficient in the penalty function. Therefore, an adaptive adjustment mechanism of the penalty coefficient is designed to solve the problem, as well as improve the scheduling results. Experimental results are used to demonstrate the correctness and practicability of the proposed scheduling algorithm.