A 3rd-order Butterworth active-RC complex band-pass filter was presented for Zig Bee(IEEE802.15.4) transceiver applications. The filter adopted cascaded complex pole stages to realize the 3 MHz bandwidth with a centre...A 3rd-order Butterworth active-RC complex band-pass filter was presented for Zig Bee(IEEE802.15.4) transceiver applications. The filter adopted cascaded complex pole stages to realize the 3 MHz bandwidth with a centre frequency of 2 MHz which was required by the Zig Bee transceiver applications. An automatic frequency tuning scheme was also designed to accommodate the performance deterioration due to the process, voltage and temperature(PVT) variations. The whole filter is implemented in a 0.18 μm standard process and occupies an area of 1.3 mm×0.6 mm. The current dissipation is 1.2 m A from a 1.8 V single power supply. Measurement results show that the image rejection ratio(IRR) of the filter is 24.1 d B with a pass-band ripple less than 0.3 d B. The adjacent channel rejection is 29.8 d B@7 MHz and alternate channel rejection 47.5 d B@12 MHz, respectively.展开更多
The 500 MHz 5-cell superconducting RF(SRF) cavity was designed aiming to be a candidate cavity for high current accelerators. A copper prototype cavity and a niobium cavity were fabricated at SINAP in 2012. In order t...The 500 MHz 5-cell superconducting RF(SRF) cavity was designed aiming to be a candidate cavity for high current accelerators. A copper prototype cavity and a niobium cavity were fabricated at SINAP in 2012. In order to ensure these cavities get the desired frequency and a good field flatness higher than 98%, frequency control was implemented in the manufacturing process and pre-tuning has been done using a simple pre-tuning frame based on the bead-pull pre-tuning method. Then, TM010-π mode frequency within 5 kHz from the target frequency was achieved and the field flatness reached 98.9% on the copper prototype cavity. Finally, the same procedure was applied to the niobium cavity to obtain a field flatness better than 98% which benefited the cavity performance in the vertical testing.展开更多
The correct rate of detection for fabric defect is affected by low contrast of images. Aiming at the problem,frequencytuned salient map is used to detect the fabric defect. Firstly,the images of fabric defect are divi...The correct rate of detection for fabric defect is affected by low contrast of images. Aiming at the problem,frequencytuned salient map is used to detect the fabric defect. Firstly,the images of fabric defect are divided into blocks. Then,the blocks are highlighted by frequency-tuned salient algorithm. Simultaneously,gray-level co-occurrence matrix is used to extract the characteristic value of each rectangular patch. Finally,PNN is used to detect the defect on the fabric image. The performance of proposed algorithm is estimated off-line by two sets of fabric defect images. The theoretical argument is supported by experimental results.展开更多
High-rise buildings are usually considered as flexible structures with low inherent damping. Therefore, these kinds of buildings are susceptible to wind-induced vibration. Tuned Mass Damper（TMD） can be used as an ef...High-rise buildings are usually considered as flexible structures with low inherent damping. Therefore, these kinds of buildings are susceptible to wind-induced vibration. Tuned Mass Damper（TMD） can be used as an effective device to mitigate excessive vibrations. In this study, Artificial Neural Networks is used to find optimal mechanical properties of TMD for high-rise buildings subjected to wind load. The patterns obtained from structural analysis of different multi degree of freedom（MDF） systems are used for training neural networks. In order to obtain these patterns, structural models of some systems with 10 to 80 degrees-of-freedoms are built in MATLAB/SIMULINK program. Finally, the optimal properties of TMD are determined based on the objective of maximum displacement response reduction. The Auto-Regressive model is used to simulate the wind load. In this way, the uncertainties related to wind loading can be taken into account in neural network’s outputs. After training the neural network, it becomes possible to set the frequency and TMD mass ratio as inputs and get the optimal TMD frequency and damping ratio as outputs. As a case study, a benchmark 76-story office building is considered and the presented procedure is used to obtain optimal characteristics of the TMD for the building.展开更多
Dynamics of the axial mode transition process in a 0.33-THz second-harmonic gyrotron is investigated to reveal the physical mechanism of realizing broadband frequency tuning in an open cavity circuit. A new interactio...Dynamics of the axial mode transition process in a 0.33-THz second-harmonic gyrotron is investigated to reveal the physical mechanism of realizing broadband frequency tuning in an open cavity circuit. A new interaction mechanism about propagating waves, featured by wave competition and wave cooperation, is presented and provides a new insight into the beam-wave interaction. The two different features revealed in the two different operation regions of low-order axial modes （LOAMs） and high-order axial modes （HOAMs） respectively determine the characteristic of the overall performance of the device essentially. The device performance is obtained by the simulation based on the time-domain nonlinear theory and shows that using a 12-kV/150-mA electron beam and TE 3,4 mode, the second harmonic gyrotron can generate terahertz radiations with frequency-tuning ranges of about 0.85 GHz and 0.60 GHz via magnetic field and beam voltage tuning, respectively. Additionally, some non-stationary phenomena in the mode startup process are also analyzed. The investiga- tion in this paper presents guidance for future developing high-performance frequency-tunable gyrotrons toward terahertz applications.展开更多
The paper introduce the measurement of some beam parameters for Hefei Light Source (HLS) by frequency domain technique, which include the betatron tune, average beta function, natural chromaticity, corrected chromatic...The paper introduce the measurement of some beam parameters for Hefei Light Source (HLS) by frequency domain technique, which include the betatron tune, average beta function, natural chromaticity, corrected chromaticity, and center frequency. Additionally, the measurement of the influence of DC clearing electrodes on the betatron tune shift is also described.Some measurement results are given. The measurement results are compared with the theoretical values and shown to be in good agreement.展开更多
为提高乘客舒适度,利用调谐质量阻尼器(tuned mass damper,TMD)对100 m X-BOW型极地探险邮轮的局部振动进行控制。建立邮轮的有限元模型,进行整船频响分析,通过比较仿真值与测试值间的误差,验证模型的有效性。根据整体模态等价质量求解...为提高乘客舒适度,利用调谐质量阻尼器(tuned mass damper,TMD)对100 m X-BOW型极地探险邮轮的局部振动进行控制。建立邮轮的有限元模型,进行整船频响分析,通过比较仿真值与测试值间的误差,验证模型的有效性。根据整体模态等价质量求解方法和局部模态质量的空间分布原则,提出混合模态中单个局部模态等价质量的求解方法,利用该方法求解邮轮局部振动区域的等价质量;利用该等价质量计算TMD的质量比;基于该质量比,求解出对应的TMD参数最优解。通过分析可知,当质量比为0.05时,TMD在13.4 Hz处具有31 dB的吸振效果,同时在10 Hz和18.8 Hz处也有一定的吸振效果,分别为3 dB和2 dB,整体控制频段较平坦,鲁棒性也较佳。展开更多
The tuned mass damper（TMD） has been successfully applied to the vibration control in machining, while the most widely adopted tuning is equal peaks, which splits the magnitude of the frequency response function（FRF...The tuned mass damper（TMD） has been successfully applied to the vibration control in machining, while the most widely adopted tuning is equal peaks, which splits the magnitude of the frequency response function（FRF） into equal peaks. However, chatter is a special self-excited problem and a chatter-flee machining is determined by FRF at the cutting zone. A TMD tuning aiming at achieving the maximum chatter stability is studied, and it is formulated as an optimization problem of maximizing the minimum negative real part of FRF. By employing the steepest descend method, the optimum frequency and damping ratio of TMD are obtained, and they are compared against the equal peaks tuning. The advantage of the proposed tuning is demonstrated numerically by comparing the minimum point of the negative real part, and is further verified by damping a flexible mode from the fixture of a turning machine. A TMD is designed and placed on the fixture along the vibration of the target mode after performing modal analysis and mode shape visualization. Both of the above two ttmings are applied to modify the tool point FRF by tuning TMD respectively. Chatter stability chart of the turning shows that the proposed tuning can increase the critical depth of cut 37% more than the equal peaks. Cutting tests with an increasing depth of cut are conducted on the turning machine in order to distinguish the stability limit. The tool vibrations during the machining are compared to validate the simulation results. The proposed damping design and optimization routine are able to further increase the chatter suppression effect.展开更多
基金Projects(61334003,61274026) supported by the National Natural Science Foundation of ChinaProject(K5051225006) supported by the Fundamental Research Fund for the Central Universities,China
文摘A 3rd-order Butterworth active-RC complex band-pass filter was presented for Zig Bee(IEEE802.15.4) transceiver applications. The filter adopted cascaded complex pole stages to realize the 3 MHz bandwidth with a centre frequency of 2 MHz which was required by the Zig Bee transceiver applications. An automatic frequency tuning scheme was also designed to accommodate the performance deterioration due to the process, voltage and temperature(PVT) variations. The whole filter is implemented in a 0.18 μm standard process and occupies an area of 1.3 mm×0.6 mm. The current dissipation is 1.2 m A from a 1.8 V single power supply. Measurement results show that the image rejection ratio(IRR) of the filter is 24.1 d B with a pass-band ripple less than 0.3 d B. The adjacent channel rejection is 29.8 d B@7 MHz and alternate channel rejection 47.5 d B@12 MHz, respectively.
文摘The 500 MHz 5-cell superconducting RF(SRF) cavity was designed aiming to be a candidate cavity for high current accelerators. A copper prototype cavity and a niobium cavity were fabricated at SINAP in 2012. In order to ensure these cavities get the desired frequency and a good field flatness higher than 98%, frequency control was implemented in the manufacturing process and pre-tuning has been done using a simple pre-tuning frame based on the bead-pull pre-tuning method. Then, TM010-π mode frequency within 5 kHz from the target frequency was achieved and the field flatness reached 98.9% on the copper prototype cavity. Finally, the same procedure was applied to the niobium cavity to obtain a field flatness better than 98% which benefited the cavity performance in the vertical testing.
文摘The correct rate of detection for fabric defect is affected by low contrast of images. Aiming at the problem,frequencytuned salient map is used to detect the fabric defect. Firstly,the images of fabric defect are divided into blocks. Then,the blocks are highlighted by frequency-tuned salient algorithm. Simultaneously,gray-level co-occurrence matrix is used to extract the characteristic value of each rectangular patch. Finally,PNN is used to detect the defect on the fabric image. The performance of proposed algorithm is estimated off-line by two sets of fabric defect images. The theoretical argument is supported by experimental results.
文摘High-rise buildings are usually considered as flexible structures with low inherent damping. Therefore, these kinds of buildings are susceptible to wind-induced vibration. Tuned Mass Damper（TMD） can be used as an effective device to mitigate excessive vibrations. In this study, Artificial Neural Networks is used to find optimal mechanical properties of TMD for high-rise buildings subjected to wind load. The patterns obtained from structural analysis of different multi degree of freedom（MDF） systems are used for training neural networks. In order to obtain these patterns, structural models of some systems with 10 to 80 degrees-of-freedoms are built in MATLAB/SIMULINK program. Finally, the optimal properties of TMD are determined based on the objective of maximum displacement response reduction. The Auto-Regressive model is used to simulate the wind load. In this way, the uncertainties related to wind loading can be taken into account in neural network’s outputs. After training the neural network, it becomes possible to set the frequency and TMD mass ratio as inputs and get the optimal TMD frequency and damping ratio as outputs. As a case study, a benchmark 76-story office building is considered and the presented procedure is used to obtain optimal characteristics of the TMD for the building.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.61471007,61531002,61522101,and 11275206)the Seeding Grant for Medicine and Information Science of Peking University,China(Grant No.2014-MI-01)
文摘Dynamics of the axial mode transition process in a 0.33-THz second-harmonic gyrotron is investigated to reveal the physical mechanism of realizing broadband frequency tuning in an open cavity circuit. A new interaction mechanism about propagating waves, featured by wave competition and wave cooperation, is presented and provides a new insight into the beam-wave interaction. The two different features revealed in the two different operation regions of low-order axial modes （LOAMs） and high-order axial modes （HOAMs） respectively determine the characteristic of the overall performance of the device essentially. The device performance is obtained by the simulation based on the time-domain nonlinear theory and shows that using a 12-kV/150-mA electron beam and TE 3,4 mode, the second harmonic gyrotron can generate terahertz radiations with frequency-tuning ranges of about 0.85 GHz and 0.60 GHz via magnetic field and beam voltage tuning, respectively. Additionally, some non-stationary phenomena in the mode startup process are also analyzed. The investiga- tion in this paper presents guidance for future developing high-performance frequency-tunable gyrotrons toward terahertz applications.
基金Supported by National Important Project on Science-Phase Ⅱ of National Synchrotron Radiation Laboratory
文摘The paper introduce the measurement of some beam parameters for Hefei Light Source (HLS) by frequency domain technique, which include the betatron tune, average beta function, natural chromaticity, corrected chromaticity, and center frequency. Additionally, the measurement of the influence of DC clearing electrodes on the betatron tune shift is also described.Some measurement results are given. The measurement results are compared with the theoretical values and shown to be in good agreement.
基金supported by National Technology Support Program of China (Grant No. 2006BAF01B09)Doctoral Foundation of Ministry of Education of China (Grant No. 200800060010)+1 种基金Beijing Municipal Key Laboratory Project of Chinasupport from the Manufacturing Automation Laboratory(MAL) of the University of British Columbia
文摘The tuned mass damper（TMD） has been successfully applied to the vibration control in machining, while the most widely adopted tuning is equal peaks, which splits the magnitude of the frequency response function（FRF） into equal peaks. However, chatter is a special self-excited problem and a chatter-flee machining is determined by FRF at the cutting zone. A TMD tuning aiming at achieving the maximum chatter stability is studied, and it is formulated as an optimization problem of maximizing the minimum negative real part of FRF. By employing the steepest descend method, the optimum frequency and damping ratio of TMD are obtained, and they are compared against the equal peaks tuning. The advantage of the proposed tuning is demonstrated numerically by comparing the minimum point of the negative real part, and is further verified by damping a flexible mode from the fixture of a turning machine. A TMD is designed and placed on the fixture along the vibration of the target mode after performing modal analysis and mode shape visualization. Both of the above two ttmings are applied to modify the tool point FRF by tuning TMD respectively. Chatter stability chart of the turning shows that the proposed tuning can increase the critical depth of cut 37% more than the equal peaks. Cutting tests with an increasing depth of cut are conducted on the turning machine in order to distinguish the stability limit. The tool vibrations during the machining are compared to validate the simulation results. The proposed damping design and optimization routine are able to further increase the chatter suppression effect.
