AUTOMATIC FINIT EELEMENT MODELING OF A WING

This paper is concerned about the automatic finite element modeling of a wing structure. The row and column method is used to identify the structure parts(ribs, spars, skins and pillars). A customization module of PCL(PATRAN Command Language under PATRAN 6.0) code from constructing airfoil curves to creating the entire wing FEM model is designed and developed. The geome tric, mesh density, material, load and boundary parameters can be easily and correctly input with the friendly interactive interface. A VFW614 wing is analyzed from creating airfoil curves to the show of stresses calculated by using NASTRAN 68 as an example. The results show that this customization module is very effective and efficient.

Structural Modeling and Aeroelastic Analysis of High-Aspect-Ratio Composite Wings

A unified structural model for high-aspect-ratio composite wing with arbitrary cross-section is developed. Two types of lay-ups of the composite wing, namely, circumferentially uniform stiffness （CUS） configuration and circumferentially asymmetric stiffness （CAS） configuration, are investigated. The present structural modeling method is validated through ANSYS FEM software for the case of a composite box beam. Then, the case of a single-cell composite wing with NACA0012 airfoil shape is considered. To investigate the aeroelastic problem of high-aspect-ratio composite wings, the linear ONERA aerodynamic model is used to model the unsteady aerodynamic loads under the case of small angle of attack. Finally, flutter speeds of the high-aspect-ratio wing with various composite ply angles are determined by using U-g method.

Multi-objective Optimization Design of Wing Structure with the Model Management Framework

Evolutionary algorithm is time-consuming because of the large number of evolutions and much times of finite element analysis, when it is used to optimize the wing structure of a certain high altitude long endurance unmanned aviation vehicle（UAV）. In order to improve efficiency it is proposed to construct a model management framework to perform the multi-objective optimization design of wing structure. The sufficient accurate approximation models of objective and constraint functions in the wing structure optimization model are built when using the model management framework, therefore in the evolutionary algorithm a number of finite element analyses can he avoided and the satisfactory multi-objective optimization results of the wing structure of the high altitude long endurance UAV are obtained.

Parametric Geometric Model and Hydrodynamic Shape Optimization of A Flying-Wing Structure Underwater Glider

Combining high precision numerical analysis methods with optimization algorithms to make a systematic exploration of a design space has become an important topic in the modern design methods. During the design process of an underwater glider＇s flying-wing structure, a surrogate model is introduced to decrease the computation time for a high precision analysis. By these means, the contradiction between precision and efficiency is solved effectively. Based on the parametric geometry modeling, mesh generation and computational fluid dynamics analysis, a surrogate model is constructed by adopting the design of experiment （DOE） theory to solve the multi-objects design optimization problem of the underwater glider. The procedure of a surrogate model construction is presented, and the Gaussian kernel function is specifically discussed. The Particle Swarm Optimization （PSO） algorithm is applied to hydrodynamic design optimization. The hydrodynamic performance of the optimized flying-wing structure underwater glider increases by 9.1%.

Modeling and Motion Simulation for A Flying-Wing Underwater Glider with A Symmetrical Airfoil

The flying-wing underwater glider (UG), shaped as a blended wing body, is a new type of underwater vehicle and still requires further research. The shape layout and the configuration of the internal actuators of the flying-wing UG are different from those of "legacy gliders" which have revolving bodies, and these two factors strongly affect the dynamic performance of the vehicle. Considering these differences, we propose a new configuration of the internal actuators for the flying-wing UG and treat the flying-wing UG as a multi-body system when establishing its dynamic model. In this paper, a detailed dynamic model is presented using the Newton-Euler method for the flying-wing UG. Based on the full dynamic model, the effect of the internal actuators on the steady gliding motion of vehicle is studied theoretically, and the relationship between the state parameters of the steady gliding motion and the controlled variables is obtained by solving a set of equilibrium equations. Finally, the behaviors of two classical motion modes of the glider are analyzed based on the simulation. The simulation results demonstrate that the motion performance of the proposed flying-wing UG is satisfactory.

Modeling and Numerical Simulation of Wings Effect on Turbulent Flow between two contra-rotating cylinders

Many industries in the world take part in the pollution of the environment. This pollution often comes from the reactions of combustion. To optimize these reactions and to minimize pollution, turbulence is a funda- mental tool. Several factors are at the origin of turbulence in the complex flows, among these factors, we can quote the effect of wings in the rotating flows. The interest of this work is to model and to simulate numeri- cally the effect of wings on the level of turbulence in the flow between two contra-rotating cylinders. We have fixed on these two cylinders eight wings uniformly distributed and we have varied the height of the wings to have six values from 2 mm to 20 mm by maintaining the same Reynolds number of rotation. The numerical tool is based on a statistical model in a point using the closing of the second order of the transport equations of the Reynolds stresses (Reynolds Stress Model: RSM). We have modelled wings effect on the flow by a source term added to the equation tangential speed. The results of the numerical simulation showed that all the average and fluctuating variables are affected the value of the kinetic energy of turbulence as those of Reynolds stresses increase with the height of the wings.

Nanoindentation Mechanical Properties and Structural Biomimetic Models of Three Species of Insects Wings

Mimicking insect flights were used to design and develop new engineering materials. Although extensive research was done to study various aspects of flying insects. Because the detailed mechanics and underlying principles involved in insect flights remain largely unknown. A systematic study was carried on insect flights by using a combination of several advanced techniques to develop new models for the simulation and analysis of the wing membrane and veins of three types of insect wings, namely dragonfly （Pantala flavescens Fabricius）, honeybee （Apis cerana cerana Fabricius） and fly （Sarcophaga carnaria Linnaeus）. In order to gain insights into the flight mechanics of insects, reverse engineering methods were used to establish three-dimensional geometrical models of the membranous wings, so we can make a comparative analysis. Then nano-mechanical test of the three insect wing membranes was performed to provide experimental parameter values for mechanical models in terms of nano-hardness and elastic modulus. Finally, a computational model was established by using the finite element analysis （ANSYS） to analyze and compare the wings under a variety of simplified load regimes that are concentrated force, uniform line-load and a torque. This work opened up the possibility towards developing an engineering basis for the biomimetic design of thin solid films and 2D advanced engineering composite materials.

Modeling and Experiment of a Morphing Wing Integrated with a Trailing Edge Control Actuation System

Morphing wing has attracted many research attention and effort in aircraft technology development because of its advantage in lift to draft ratio and flight performance.Morphing wing technology combines the lift and control surfaces into a seamless wing and integrates the primary structure together with the internal control system.It makes use of the wing aeroelastic deformation induced by the control surface to gain direct force control through desirable redistribution of aerodynamic forces.However some unknown mechanical parameters of the control system and complexity of the integrated structure become a main challenge for dynamic modeling of morphing wing.To solve the problem,a method of test data based modal sensitivity analysis is presented to improve the morphing wing FE model by evaluating the unknown parameters and identifying the modeling boundary conditions.An innovative seamless morphing wing with the structure integrated with a flexible trailing edge control system is presented for the investigation.An experimental model of actuation system driven by a servo motor for the morphing wing is designed and established.By performing a vibration test and the proposed modal sensitivity analysis,the unknown torsional stiffness of the servo motor and the boundary condition of the actuation mechanism model is identified and evaluated.Comparing with the test data,the average error of the first four modal frequency of the improved FE model is reduced significantly to less than 4%.To further investigate the morphing wing modeling,a wing box and then a whole morphing wing model including the skin and integrated with the trailing edge actuation system are established and tested.By using the proposed method,the FE model is improved by relaxing the constraint between the skin and actuation mechanism.The results show that the average error of the first three modal frequency of the improved FE model is reduced to less than 6%.The research results demonstrate that the presented seamless morphing wing integrated with a flexible trailing edge control surface can improve aerodynamic characteristics.By using the test data based modal sensitivity analysis method,the unknown parameter and boundary condition of the actuation model can be determined to improve the FE model.The problem in dynamic modeling of high accuracy for a morphing wing can be solved in an effective manner.

Modeling and Numerical Simulation of Wings Effect on Turbulent Flow between Two Contra-Rotating Discs

Turbulence is a fundamentally interesting physical phenomenon which is of fundamental interest. Indeed, it is at the origin of several industrial applications, the control of energy in these industrial applications pass by the comprehension and the modelling of turbulent flows. Several factors are at the origin of turbulence in the complex flows, among these factors, we can quote the effect of wings in the rotating flows. The interest of this work is to model and to simulate numerically the effect of wings on the level of turbulence in the flow between two contra-rotating discs. We have fixed on these two discs eight wings uniformly distributed and we have varied the height of the wings to have eleven values from 0 to 18 mm by maintaining the same Reynolds number of rotation. The numerical tool is based on a statistical model in a point using the closing of the second order of the transport equations of the Reynolds stresses （Reynolds Stress Model： RSM）. We have modelled wings effect on the flow by a source term added to the equation tangential speed. The results of the numerical simulation showed that all the average and fluctuating variables are affected the value of the kinetic energy of turbulence as those of Reynolds stresses increase with the height of the wings.

Parametric CAD Modelling of Aircraft Wings for FEA Vibration Analysis

Excessive vibration of aircraft wings during flight is harmful and may cause propagation of existing cracks in the material, leading to catastrophic failures as a result of material fatigue. This study investigates the variations of modal characteristics of aircraft wings with respect to changes in the structural configurations. We develop parametric Computer-Aided Design (CAD) models to capture new design intend on the aircraft wing architectures. Subsequent Finite Element Analysis (FEA) based vibration analysis is performed to study the effects of architecture changes on the wing’s natural frequencies and mode shapes. It is concluded that the spar placement and the number of ribs have significant influence on the wing’s natural vibration properties. Integrating CAD modelling and FEA vibration analysis enables designers to develop alternative wing architectures to implement design requirements in the preliminary design stage.

Optimization of Fairhurst-Cook Model for 2-D Wing Cracks Using Ant Colony Optimization (ACO), Particle Swarm Intelligence (PSO), and Genetic Algorithm (GA)

The common failure mechanism for brittle rocks is known to be axial splitting which happens parallel to the direction of maximum compression. One of the mechanisms proposed for modelling of axial splitting is the sliding crack or so called, “wing crack” model. Fairhurst-Cook model explains this specific type of failure which starts by a pre-crack and finally breaks the rock by propagating 2-D cracks under uniaxial compression. In this paper, optimization of this model has been considered and the process has been done by a complete sensitivity analysis on the main parameters of the model and excluding the trends of their changes and also their limits and “peak points”. Later on this paper, three artificial intelligence algorithms including Particle Swarm Intelligence (PSO), Ant Colony Optimization (ACO) and genetic algorithm (GA) has been used and compared in order to achieve optimized sets of parameters resulting in near-maximum or near-minimum amounts of wedging forces creating a wing crack.

Modeling of Roll-Heave-Pitch Motions of a Ram Wing Translating over Non-uniform Surface

Ground-effect vehicles flying close to water or ground often employ ram wings which generate aerodynamic lift primarily on their lower surfaces.The subject of this paper is the 3-DOF modeling of roll,heave,and pitch motions of such a wing in the presence of surface waves and other ground non-uniformities.The potential-flow extreme-ground-effect theory is applied for calculating unsteady pressure distribution under the wing which defines instantaneous lift force and moments.Dynamic simulations of a selected ramwing configuration are carried out in the presence of surface waves of various headings and wavelengths,as well as for transient flights over a ground obstacle.The largest amplitudes of the vehicle motions are observed in beam waves when the periods of the encounter are long.Nonlinear effects are more pronounced for pitch angles than for roll and heave.The present method can be adapted for modeling of air-supported lifting surfaces on fast marine vehicles.

Quantitative analysis of the morphing wing mechanism of raptors:Morphing kinematics of Falco peregrinus wing

Raptors are getting more attention from researchers because of their excellent flight abilities.And the excellent wing morphing ability is critical for raptors to achieve high maneuvering flight,which can be a good bionic inspiration for unmanned aerial vehicles(UAV)design.However,morphing wing motions of Falco peregrinus with multi postures cannot be consulted since such a motion database was nonexistent.This study aimed to provide data reference for future research in wing morphing kinetics.We used the computed tomography(CT)approach to obtain nine critical postures of the Falco peregrinus wing skeleton,followed with motion analysis of each joint and bone.Based on the obtained motion database,a six-bar kinematic model was proposed to regenerate wing motions with a high fidelity.

Analysis and Research on Equivalent Model of Airbus A380 Wing Beam

With the development of aviation industry,civil aviation has become an indispensable part.Our team will take all the structural dimensions,loads and material parameters in the wing beam structure as the specific values determined during the structural design to conduct deflection analysis on the wing beam structure of A380 passenger plane.According to the deflection and parameters analyzed,the stress distribution and maximum stress position on the wing beam can be known.Through the analysis of the wing parameters,the finite element analysis of the wing beam,the mesh sensitivity analysis,and the analysis of the wing tip deflection,the relevant safety factors of the aircraft are obtained.The results show that the wing of airbus A380 is more reliable and safer through the calculation of deflection,stress and safety factor.

一种小型火工机构的输出计算及其验证

针对某折叠翼展开机构的小型化难题,研究了一种小型火工机构。利用内弹道理论建立了该火工机构的输出理论模型,通过理论模型计算和优化了机构参数,并用有限元法校验了计算结果。测试结果表明:该原型机具备了小型特点,其输出角度达到了128.5°。在逆风和顺风负载下,该火工机构的工作时间均小于200 ms,其最大角速度不大于3 000 (°)/s,试验数据证实该火工机构具备缓冲作用,理论计算结果和试验数据基本一致。研究成果可作为薄型折叠翼的一种设计方法,为薄型折叠翼的工程应用奠定技术基础。

四川地区精细化降水预报融合订正试验及检验

精细化定量降水网格预报是天气预报业务的重点和难点,基于西南区域智能数值网格模式预报系统(Southwest China WRF-based Intelligent Numeric Grid forecast System,SWC-WINGS)1 km×1 km分辨率的小时降水预报,利用时间滞后和概率匹配方法开展融合订正试验,再利用中国气象局多源融合降水系统(CMA Multi-source Precipitation Analysis System,CMPAS)三源融合降水实况格点数据,对2022年7—8月四川地区的小时降水预报融合订正结果进行检验,并在四川盆地西部一次短时强降水天气过程中进行应用,结果表明:(1)时间滞后集合降水预报相较于模式降水预报,存在小量级预报过度,大量级预报过于保守的问题;(2)时间滞后结合概率匹配的降水预报融合订正方法有效提升了各量级降水预报的TS评分,尤其1~2 h预报时效提升显著,小时雨量超过0.1 mm、5 mm、10 mm和20 mm量级的TS评分平均提升率分别为7.2%、17.2%、28.3%和36.3%;(3)一次短时强降水天气过程的应用结果表明,时间滞后结合概率匹配的融合订正方法对模式小时降水预报有较好的改进效果,尤其对大量级降水预报有较强的订正能力。

应用于水陆两栖勘测及紧急救援的仿生机械龟

针对现有水下航行器能耗高、噪声大、续航能力一般等问题,通过探索水下仿生扑翼的推进机理,结合流体力学运动的知识,利用SolidWorks仿造龟的外形设计了仿生机械龟。该机械龟装载浮力与重力感应系统,通过PID算法控制机器在水中的平衡,使用Arduino作为主控制板,利用传感器、摄像系统与数据传输系统,进行实时监测并传输数据,龟壳中设计了贮藏空间,满足勘测和物资救援任务。实验结果表明,所设计的水陆两栖仿生机械龟优化了形态和运行控制系统,对比美国耶鲁大学研制出的仿乌龟形水陆两栖机器人ART,能够适应多样化地形高效的运动,具有高灵活性和机动性,能完成对水中温度、压强、地形进行实时监测并将数据传输回终端。

基于NSGA-Ⅱ算法的机翼风洞模型静强度试验加载方案优化设计

针对机翼风洞模型的静强度试验,提出一种基于NSGA-Ⅱ算法试验加载方案的优化设计方法,包括加载布局的设计和试验载荷的多目标优化设计。加载布局的设计中引入控制剖面的设置,并在此基础上建立试验载荷的多目标优化设计模型,以控制剖面内的剪力、弯矩和转矩误差为优化目标,以静力等效原则和误差最小要求为约束条件,并以CHN-T1标模为例,基于NSGA-Ⅱ算法进行多目标优化模型的求解,算法采用可行性法则处理约束条件。最终求解出最优的试验加载方案并进行方案的有限元仿真验证。结果表明:试验方案与流固耦合下的理想试验的最大等效应力、应变值和变形位移的误差均小于6%,经优化设计的加载方案较好地模拟了气动载荷。

翼身融合布局飞机分布式推进边界层吸入效应影响研究

翼身融合布局是指机翼和机身高度融合的全升力面飞机外形,在提升巡航效率和减排降噪等方面展现出明显的性能优势和发展潜力.采用雷诺平均Navier-Stokes方法结合基于叶素理论的体积力模型,针对翼身融合布局民机分布式推进边界层吸入(BLI)效应影响下的绕流流场进行了数值研究.首先,将翼身融合布局民机分布式BLI推进构型简化为涵道风扇-机翼段耦合构型,计算涵道风扇质量流率小于1、等于1以及大于1的3个工况,对比分析了滑移网格方法、冻结转子方法和基于叶素理论的体积力模型法的流场细节、计算精度以及计算效率.其次,建立分布式BLI推进-机翼耦合构型,对此构型不同转速下的绕流流场进行对比分析,探究并验证所建立的分布式BLI推进系统抑制分离的能力.最后,将分布式BLI推进安装于翼身融合布局飞机概念方案NPU-BWB-300机翼与机身的融合段,探究其对NPU-BWB-300绕流流场的影响.研究结果表明:滑移网格方法、冻结转子方法和基于叶素理论的体积力模型方法均可以较好地刻画涵道风扇边界层吸入效应的流场细节;所建立的分布式BLI推进系统具备抑制分离的能力,将其应用于NPU-BWB-300也可以取得较为明显地改善分离流场的效果.

带襟翼导轨翼肋后缘尺寸-拓扑综合优化的摄动神经网络代理模型法

带襟翼导轨的翼肋后缘设计需要确定肋缘条、腹板的尺寸和肋腹板的拓扑形状,对此提出了一种针对尺寸-拓扑综合优化的摄动神经网络(perturbation neural network, PNN)代理模型法.其基本思想是基于拓扑优化对参数的敏感性,引入了对试验设计(design of experiments, DOE)样本点的摄动,通过过滤手段捕获拓扑突变点,并降低数值噪声,极大地提高了代理模型的预测精度,将拓扑优化过程作为黑盒,直接建立起尺寸变量与拓扑优化后结构响应的代理模型.最后在代理模型上进行优化,得到了结构尺寸与拓扑形状的最优组合.该文完成了一个翼肋后缘优化典型算例,证明了该方法的有效性和优越性.