Design of radiation hard phase-locked loop at 2.5 GHz using SOS-CMOS

A radiation hard phase-locked loop （PLL） is designed at 2.5 GHz using silicon on sapphire complementary metal-oxide-semiconductor process. Radiation hardness is achieved through improving circuit design without sacrificing real estate. Stability is guaranteed by a fully self-bias architecture. The lock time of PLL is minimized by maximizing the loop bandwidth. Frequency tuning range of voltage controlled oscillator is significantly enhanced by a novel load configuration. In addition, multiple bias stages, asynchronous frequency divider, and silicon on sapphire process jointly make the proposed PLL more radiation hard. Layout of this PLL is simulated by Cadence Spectre RF under both single event effect and total induced dose effect. Simulation results demonstrate excellent stability, lock time 〈 600 ns, frequency tuning range [1.57 GHz, 3.46 GHz], and jitter 〈 12 ps. Through comparison with PLLs in literatures, the PLL is especially superior in terms of lock time and frequency tuning range performances.

Novel Control Strategy for Multi-Level Active Power Filter without Phase-Locked-Loop

Active power filter (APF) using novel virtual line-flux-linkage oriented control strategy can not only realizes no phase-locked-loop (PLL) control, but also achieves a good inhibitory effect to interfere. However, there are some problems in the conventional method, such as the error of amplitude, the shift of phase angle and the non-determinacy of initial oriented angle. In this paper, two one-order low-pass filters are adopted instead of the pure integrator in the virtual line-flux-linkage observer, which can steady the phase and amplitude. Furthermore, an original scheme of harmonics detection under the rotating coordinate is advanced based on the simplified space vector pulse width modulation (SVPWM) strategy. Meanwhile, by using the new SVPWM algorithm, the voltage space vector diagram of the three-level inverter can be simplified and applied into that of two-level inverter, and this makes the control for Neutral Point potential easier.

A sapphire fibre thermal probe based on fast Fourier transform and phase-lock loop

A sapphire fibre thermal probe with Cr^3＋ ion-doped end is developed by using the laser heated pedestal growth method. The fluorescence thermal probe offers advantages of compact structure, high performance and ability to withstand high temperature in a detection range from room temperature to 450℃. Based on the fast Fourier transform （FFT）, the fluorescence lifetime is obtained from the tangent function of phase angle of the non-zeroth terms in the FFT result. This method has advantages such as quick calculation, high accuracy and immunity to the background noise. This FFT method is compared with other traditional fitting methods, indicating that the standard deviation of the FFT method is about half of that of the Prony method and about 1/6 of that of the log-fit method. And the FFT method is immune to the background noise involved in a signal. So, the FFT method is an excellent way of processing signals. In addition, a phase-lock amplifier can effectively suppress the noise.

A novel high precision Doppler frequency estimation method based on the third-order phase-locked loop

In deep space exploration,many engineering and scientific requirements require the accuracy of the measured Doppler frequency to be as high as possible.In our paper,we analyze the possible frequency measurement points of the third-order phase-locked loop(PLL)and find a new Doppler measurement strategy.Based on this finding,a Doppler frequency measurement algorithm with significantly higher measurement accuracy is obtained.In the actual data processing,compared with the existing engineering software,the accuracy of frequency of 1 second integration is about 5.5 times higher when using the new algorithm.The improved algorithm is simple and easy to implement.This improvement can be easily combined with other improvement methods of PLL,so that the performance of PLL can be further improved.

THE DESIGN OF AN ALL-DIGITAL PHASE-LOCKED LOOP WITH LOW JITTER BASED ON ISF ANALYSIS

A low jitter All-Digital Phase-Locked Loop(ADPLL) used as a clock generator is designed.The Digital-Controlled Oscillator(DCO) for this ADPLL is a seven-stage ring oscillator with the delay of each stage changeable.Based on the Impulse Sensitivity Function(ISF) analysis,an effective way is proposed to reduce the ADPLL's jitter by the careful design of the sizes of the inverters used in the DCO with a simple architecture other than a complex one.The ADPLL is implemented in a 0.18μm CMOS process with 1.8V supply voltage,occupies 0.046mm2 of on-chip area.According to the measured results,the ADPLL can operate from 108MHz to 304MHz,and the peak-to-peak jitter is 139ps when the DCO's output frequency is 188MHz.

An improved arctangent algorithm based on phase-locked loop for heterodyne detection system

We present an ameliorated arctangent algorithm based on phase-locked loop for digital Doppler signal processing,utilized within the heterodyne detection system. We define the error gain factor given by the approximation of Taylor expansion by means of a comparison of the measured values and true values. Exact expressions are derived for the amplitude error of two in-phase & quadrature signals and the frequency error of the acousto-optic modulator. Numerical simulation results and experimental results make it clear that the dynamic instability of the intermediate frequency signals leads to cumulative errors, which will spiral upward. An improved arctangent algorithm for the heterodyne detection is proposed to eliminate the cumulative errors and harmonic components. Depending on the narrow-band filter, our experiments were performed to realize the detectable displacement of 20 nm at a detection distance of 20 m. The aim of this paper is the demonstration of the optimized arctangent algorithm as a powerful approach to the demodulation algorithm, which will advance the signal-to-noise ratio and measurement accuracy of the heterodyne detection system.

A LOW POWER TIME-TO-DIGITAL CONVERTER FOR ALL-DIGITAL PHASE-LOCKED LOOP

Time-to-Digital Converter (TDC) is a key block used as the phase/frequency detector in an All-Digital Phase-Locked Loop (ADPLL). Usually, it occupies a large proportion of ADPLL's total power consumption up to about 30% to 40%. In this paper, the detailed power consumption of different components in the TDC is analyzed. A Power Management Block (PMB) is presented for the TDC to reduce its power consumption. A 24-bits TDC core with the proposed PMB is implemented in HJTC 0.18 μm CMOS technology. Simulation results show that up to 84% power reduction is achieved using our proposed technique.

A Digital Phase Locked Loop Speed Control of Three Phase Induction Motor Drive: Performances Analysis

This paper deals with performance analysis and implementation of a three phase inverter fed induction motor (IM) drive system. The closed loop control scheme of the drive utilizes the Digital Phase Locked Loop (DPLL). The DPLL is safely implemented all around the well known integrated circuit DPLL 4046. An ex-perimental verification is carried out on one kw scalar controlled IM system drives for a wide range of speeds and loads appliance. This presents a simple and high performance solution for industrial applications.

A Low Phase Noise Ring-VCO Based PLL Using Injection Locking for ZigBee Applications

A low power low phase noise frequency synthesizer with subharmonic injection locking is proposed for ZigBee applications. The PLL is based on a ring VCO to decrease area and production cost. In order to improve phase noise performance, a high frequency injection signal of which frequency varies with channel number is used. The circuit is designed in TSMC 0.18 μm CMOS technology and simulated in ADS (Advanced Design System). The phase noise at 3.5 and 10 MHz offsets is -116 and -118 dBc/Hz, respectively, and total circuit consumes 2.2 mA current.

Multi-Order Intermittent Chaotic Synchronization of Closed Phase Locked Loop

For the model of a Closed Phase Locked Loop (CPLL) communication System consists of both the transmission and receiver ends. This model is considered to be in a multi-order intermittent chaotic state. The chaotic signals are then synchronized along side with our system. This chaotic synchronization will be demonstrated and furthermore, a modulation will be formed to examine the system if it will perfectly reconstruct or not. Finally we will demonstrate the synchronization conditions of the system.

Hybrid phase-locked loop with fast locking time and low spur in a 0.18-μm CMOS process

We propose a novel hybrid phase-locked loop （PLL） architecture for overcoming the trade-off between fast locking time and low spur. To reduce the settling time and meanwhile suppress the reference spurs, we employ a wide-band single-path PLL and a narrow-band dual-path PLL in a transient state and a steady state, respectively, by changing the loop bandwidth according to the gain of voltage controlled oscillator （VCO） and the resister of the loop filter. The hybrid PLL is implemented in a 0.18-μm complementary metal oxide semiconductor （CMOS） process with a total die area of 1.4×0.46 mm2. The measured results exhibit a reference spur level of lower than -73 dB with a reference frequency of 10 MHz and a settling time of 20 μs with 40 MHz frequency jump at 2 GHz. The total power consumption of the hybrid PLL is less than 27 mW with a supply voltage of 1.8 V.

Phase-Locked Loop Based Cancellation of ECG Power Line Interference

Power line(PL)interference is one significant artifact in electrocardiography(ECG)that needs to be reduced to ensure accurate recording of cardiac signals.Because PL interference is non-stationary and has varying frequency,phase,and amplitude in ECG measurement,adaptive techniques are often necessary to track and cancel the interference.In this paper we present a phase-locked loop(PLL)-based adaptive filter to cancel PL interference.The PLL obtains the reference signal that is fed into the adaptive filter to remove the PL interference at the central frequency of 50 Hz.It is found that the technique can effectively cancel PL interference in real ECG signals and,when compared with some existing techniques such as least mean squares(LMS)adaptive filter,the new technique produces better results in terms of signal-to-interference ratio(SIR).

A Static Phase Offset Reduction Technique for Multiplying Delay-Locked Loop

Static phase offset (SPO) in conventional multiplying delay-locked loops (MDLLs) dramatically degrades the deterministic jitter performance. To overcome the issue, this paper presents a new SPO reduction technique for MDLLs. The technique is based on the observation that the SPO of MDLL is mainly caused by the non-idealities on charge pump (e.g. sink and source current mismatch), and control line (e.g. gate leakage of loop filter and voltage controlled delay line (VCDL) control circuit). With a high gain stage inserting between phase detector/phase frequency detector (PD/PFD) and charge pump, the equivalent SPO has been decreased by a factor equal to the gain of the gain stage. The effectiveness of the proposed technique is validated by a Simulink model of MDLL. The equivalent SPO is measured by the power level of reference spur.

Dynamic Free-Spectral-Range Measurement for Fiber Resonator Based on Digital-Heterodyne Optical Phase-Locked Loop

We propose a novel scheme, based on digital-heterodyne optical phase-locked loop with whole-fiber circuit, to dynamically measure the free-spectral-range of a fiber resonator. The optical phase-locked loop is established with a differential frequency-modulation module consists of a pair of acousto-optic modulators. The resonance-tracking loop is derived with the Pound-Drever-Hall technique for locking the heterodyne frequency of the OPLL on the frequency difference between adjacent resonance modes. A stable locking accuracy of about 7 × 10?9 and a dynamic locking accuracy of about 5 × 10?8 are achieved with the FSR of 8.155 MHz, indicating a bias stability of the resonator fiber optic gyro of about 0.1?/h with 10 Hz bandwidth. In addition, the thermal drift coefficient of the FSR is measured as 0.1 Hz/?C. This shows remarkable potential for realizing advanced optical measurement systems, such as the resonant fiber optic gyro, and so on.

A PLL Clock Frequency Multiplier Using Dynamic Current Matching Adaptive Charge-Pump and VCO Frequency Reuse

A 3.5 times PLL clock frequency multiplier for low voltage different signal （LVDS） driver is presented. A novel adaptive charge pump can automatically switch the loop bandwidth and a voltage-controlled oscillator （VCO） is designed with the aid of frequency ranges reuse technology. The circuit is implemented using 1st Silicon 0.25 μm mixed-signal complementary metal-oxide-semiconductor （CMOS） process. Simulation results show that the PLL clock frequency multiplier has very low phase noise and very short capture time .

A novel Doppler frequency measurement method based on the closed-loop signal correlation for deep space exploration

In deep space exploration,it is necessary to improve the accuracy of frequency measurement to meet the requirements of precise orbit determination and various scientific studies.A phase detector is one of the key modules that restricts the tracking performance of phase-locked loop(PLL).Based on the phase relationship between adjacent signals in the time domain,a novel phase detector is presented to replace the arctangent phase detector.The new PLL,which is a closed loop signal correlation algorithm,shows good performance in tracking signals with high precision and the tracking accuracy of frequency of1 second integration is close to Cramer-Rao lower bound(CRLB)when setting proper parameters.Actual data processing results further illustrate the excellent performance of the novel PLL.

Chip design of a 5.8-GHz fractional-N frequency synthesizer with a tunable G_m-C loop filter

This paper proposes a novel Gm-C loop filter instead of a conventional passive loop filter used in a phase-locked loop. The innovative advantage of the proposed architecture is tunable loop filter bandwidth and hence the process variations of passive elements of resistance R and capacitance C can be overcome and the chip area is greatly reduced. Furthermore, the MASH 1-1-1 sigma-delta （ZA） modulator is adopted for performing the fractional division number and hence improves the phase noise as well. Measured results show that the locked phase noise is -114.1 dBc/Hz with lower Gm-C bandwidth and -111.7 dBm/C with higher Gm-C bandwidth at 1 MHz offset from carrier of 5.68 GHz. Including pads and built-in Gm-C filter, the chip area of the proposed frequency synthesizer is 1.06 mm2. The output power is -8.69 dBm at 5.68 CHz and consumes 56 mW with an off-chip buffer from 1.8-V supply voltage.

弱电网下光伏并网系统锁相环参数自适应控制

针对弱电网下PLL(phase-looked loop,PLL)会使并网逆变器的稳定性下降问题,提出一种锁相环带宽自适应控制策略来实现锁相环参数依据电网实时阻抗值来获得最优的控制参数,保证系统最佳控制性能和稳定运行,从而提升跟网型逆变器在弱电网下的对电网阻抗的适应能力。利用PSCAD/EMTDC进行仿真验证,仿真结果证明自适应控制策略正确、有效。

并网逆变器非线性特性建模及稳定性研究综述

并网逆变器作为连接新能源分布式发电和电网之间的关键接口,发挥着将电能高效、高质量馈入电网的重要作用。随着新能源渗透率的持续提高,并网点处电网存在诸如高电网阻抗、丰富的低频谐波、电压幅值/频率波动甚至故障等复杂状况。鉴于并网逆变器本质上是一个多输入、强耦合的非线性系统,沿用传统的线性建模与分析方法已难以解释工程中的复杂谐波振荡现象,并网逆变器的稳定性分析及其稳定运行受到巨大挑战。为此,该文首先具体阐述了线性与非线性和系统受扰大小之间的关系,指出大干扰稳定性分析更依赖于非线性建模及分析方法的应用。在此基础上,对已见诸报道的并网逆变器稳定性分析方法进行了归纳和对比。然后,详细阐述了稳定性分析方法在并网逆变器特定非线性环节中的应用。最后,总结并讨论了现有研究的不足,以期进一步促进“双高”背景下并网装置非线性建模和稳定性分析的研究。