The transient mass transter processes in the natural drying of wood particle materials were experimental;y studied A new theory tio determme the mass transfer parameters in the Materials was developed in terms of grad...The transient mass transter processes in the natural drying of wood particle materials were experimental;y studied A new theory tio determme the mass transfer parameters in the Materials was developed in terms of gradient transformation method(GTM).By making use of GTM.Thewater vapour diffusion coefficient and the surtaee emission coefficent of wood chip were expermentally determined both in air phase and in solid phase.It Was found that the internal resistance to water vapour diffusion in the air phase of wood partiele aggregates is around ten to the third power as large as that in common air The drag coefficient was given to quantify the effect The phenomenon of undersurface diffusion in wood partiele bed was quantitatively modelled.The dimensionless Fourier snumber and the Biot's number for mass transfer were theoretically derived.The study showed that Biot's number for the problem investigated was the ratio of the characteristie length of wood partiele bed to the penetrating depth of the undersurface.An analytical solution of the nonlinear goveming equation for water transport process in the aggregates of wood chip was obtained by introducing the variable coefficients measured in the study into the governing equation.The comparison between the analytical solution and the observed moisture content of wood chip showed that the deviation was less than ±7%.The thermophysieal properties of wood particle materials are little known at present.The knowledge provided in the paper will be and in the handling.researeh or engineering application of wood chip.wood shavingsete.展开更多
In the present manuscript numerical analysis on the ballistic performance of a tungsten particle/metallic glass matrix(WP/MG) composite rod is conducted by integrating with related experimental investigations. In the ...In the present manuscript numerical analysis on the ballistic performance of a tungsten particle/metallic glass matrix(WP/MG) composite rod is conducted by integrating with related experimental investigations. In the corresponding finite element method(FEM) simulations a modified coupled thermomechanical constitutive model is employed to describe the mechanical properties of metallic glass(MG)matrix, and geometrical models of the WP/MG composite rod are established based on its inner structure. The deformation and failure characteristics of the rod and target materials are analyzed in detail,and the influences of various factors on the ballistic performance of the WP/MG composite long rod are discussed. Related analysis demonstrates that the penetrating performance of the WP/MG rod is similar to that of the tungsten fiber/metallic glass matrix(WF/MG) composite long rod, i.e., a "self-sharpening" behavior also occurs during the penetration process, and correspondingly its penetrating capability is better than that of the tungsten heavy alloy(WHA) rod. However, the mass erosion manner of the WP/MG rod is different and the erosion is relatively severe, thus its penetrating capability is a little lower compared with that of the WF/MG one. Moreover, the impact velocity and the target strength have significant influences on the ballistic performance of the WP/MG composite rod, whereas the effect of initial nose shape is very little.展开更多
The experimental creep data were focused on wood-flour （WF）/poly vinyl chloride （PVC） composites with the variations in additive concentrations of wood flour, silane coupling agent, organomodified montmorillonite ...The experimental creep data were focused on wood-flour （WF）/poly vinyl chloride （PVC） composites with the variations in additive concentrations of wood flour, silane coupling agent, organomodified montmorillonite （OMMT） and nano-cacium carbonate （nano-CaCO3）. Their effects were analyzed using the Four-element Burger Model incorporating microscopic mechanisms. Total creep strain was low with increasing WF while elastic strain was high and plastic flow strain was low in modeling. Modification of WF with silane was beneficial to creep resistance, so did adding low ratio of OMMT （1.5 wt%） and nano-CaCO3 in composites. Thus, it was effective in reducing creep either by stiffening the PVC matrix using rigid nano-particles or by improving their adhesion with resin. However, superfluous quantity of any additament did not benefit the improvement owing to either earlier destruction of their agglomerates or stress-concentrated cracks in the over-incrassated interface.展开更多
Pulverizing is an essential unit operation in co-firing biomass with coal.Pulverizers are only compatible with pellet forms of fibrous biomass materials and crush them down to their original forming particle sizes.Tha...Pulverizing is an essential unit operation in co-firing biomass with coal.Pulverizers are only compatible with pellet forms of fibrous biomass materials and crush them down to their original forming particle sizes.That is why the data on the size distribution of the particles forming a biomass pellet is crucial to achieving optimum combustion conditions.The current study determines the internal particle size distribution of pellets after wet disintegration,following Iso 17830 standard,and aims to suggest improvements to the mentioned standard based on new measured evidence.Experiments were carried out on white wood pellets(no bark)and brown wood pellets containing bark at four water temperatures:20,40,60,and 95℃,with or without stirring.The particle size distribution of the pre-pelletizer wood particles was also measured and compared with particles in the formed pellets.Ambient water temperature of 20℃ was found to be adequate for the complete disintegration of pellets,and no mechanical stirring was required.About 30% of particles in the disintegrated pellets were 0.5-1.0 mm.Pelletization changes the particle size distribution to smaller particles.The disintegrated bark pellets contained more fines than white pellets.展开更多
文摘The transient mass transter processes in the natural drying of wood particle materials were experimental;y studied A new theory tio determme the mass transfer parameters in the Materials was developed in terms of gradient transformation method(GTM).By making use of GTM.Thewater vapour diffusion coefficient and the surtaee emission coefficent of wood chip were expermentally determined both in air phase and in solid phase.It Was found that the internal resistance to water vapour diffusion in the air phase of wood partiele aggregates is around ten to the third power as large as that in common air The drag coefficient was given to quantify the effect The phenomenon of undersurface diffusion in wood partiele bed was quantitatively modelled.The dimensionless Fourier snumber and the Biot's number for mass transfer were theoretically derived.The study showed that Biot's number for the problem investigated was the ratio of the characteristie length of wood partiele bed to the penetrating depth of the undersurface.An analytical solution of the nonlinear goveming equation for water transport process in the aggregates of wood chip was obtained by introducing the variable coefficients measured in the study into the governing equation.The comparison between the analytical solution and the observed moisture content of wood chip showed that the deviation was less than ±7%.The thermophysieal properties of wood particle materials are little known at present.The knowledge provided in the paper will be and in the handling.researeh or engineering application of wood chip.wood shavingsete.
基金supported by the Science and Technology Development Fund (2015B0201025)the key subject "Computational Solid Mechanics" of China Academy of Engineering Physics+1 种基金the National Outstanding Young Scientists Foundation of China (11225213)the National Natural Science Foundation of China (11521062,11602258)
文摘In the present manuscript numerical analysis on the ballistic performance of a tungsten particle/metallic glass matrix(WP/MG) composite rod is conducted by integrating with related experimental investigations. In the corresponding finite element method(FEM) simulations a modified coupled thermomechanical constitutive model is employed to describe the mechanical properties of metallic glass(MG)matrix, and geometrical models of the WP/MG composite rod are established based on its inner structure. The deformation and failure characteristics of the rod and target materials are analyzed in detail,and the influences of various factors on the ballistic performance of the WP/MG composite long rod are discussed. Related analysis demonstrates that the penetrating performance of the WP/MG rod is similar to that of the tungsten fiber/metallic glass matrix(WF/MG) composite long rod, i.e., a "self-sharpening" behavior also occurs during the penetration process, and correspondingly its penetrating capability is better than that of the tungsten heavy alloy(WHA) rod. However, the mass erosion manner of the WP/MG rod is different and the erosion is relatively severe, thus its penetrating capability is a little lower compared with that of the WF/MG one. Moreover, the impact velocity and the target strength have significant influences on the ballistic performance of the WP/MG composite rod, whereas the effect of initial nose shape is very little.
文摘The experimental creep data were focused on wood-flour （WF）/poly vinyl chloride （PVC） composites with the variations in additive concentrations of wood flour, silane coupling agent, organomodified montmorillonite （OMMT） and nano-cacium carbonate （nano-CaCO3）. Their effects were analyzed using the Four-element Burger Model incorporating microscopic mechanisms. Total creep strain was low with increasing WF while elastic strain was high and plastic flow strain was low in modeling. Modification of WF with silane was beneficial to creep resistance, so did adding low ratio of OMMT （1.5 wt%） and nano-CaCO3 in composites. Thus, it was effective in reducing creep either by stiffening the PVC matrix using rigid nano-particles or by improving their adhesion with resin. However, superfluous quantity of any additament did not benefit the improvement owing to either earlier destruction of their agglomerates or stress-concentrated cracks in the over-incrassated interface.
文摘Pulverizing is an essential unit operation in co-firing biomass with coal.Pulverizers are only compatible with pellet forms of fibrous biomass materials and crush them down to their original forming particle sizes.That is why the data on the size distribution of the particles forming a biomass pellet is crucial to achieving optimum combustion conditions.The current study determines the internal particle size distribution of pellets after wet disintegration,following Iso 17830 standard,and aims to suggest improvements to the mentioned standard based on new measured evidence.Experiments were carried out on white wood pellets(no bark)and brown wood pellets containing bark at four water temperatures:20,40,60,and 95℃,with or without stirring.The particle size distribution of the pre-pelletizer wood particles was also measured and compared with particles in the formed pellets.Ambient water temperature of 20℃ was found to be adequate for the complete disintegration of pellets,and no mechanical stirring was required.About 30% of particles in the disintegrated pellets were 0.5-1.0 mm.Pelletization changes the particle size distribution to smaller particles.The disintegrated bark pellets contained more fines than white pellets.
