Influence of yield-to-tensile strength ratio(Y/T) on failure assessment of defect-free and corroded X70 steel pipeline

The effect of yield-to-tensile strength ratio(Y/T) on failure pressure of X70 pipeline without and with corrosion defects was investigated.The stress-strain response of materials was characterized by a power-law hardening curve.Two formulas to estimate the strain hardening exponent n for a special Y/T were obtained by least squared regression method and the influence of Y/T on n was analyzed.As an application of n-Y/T expression,the analytical solutions of burst pressure for X70 pipeline without and with corrosion defects were also obtained.The results indicate that the burst pressure of defect-free X70 pipe without corrosion defects is a function of the Y/T,pipe geometry t0/D0 and engineering tensile strength,and increases as Y/T or t0/D0 increases; whilst the burst pressure of corroded X70 pipe decreases with the increase of defect depths,d/t.Comparisons indicate that the present analytical solutions closely match available experimental and numerical data.

Effect of natural and synthetic fibers reinforcement on California bearing ratio and tensile strength of clay

Use of environmentally friendly approaches with the purpose of strengthening soil layers along with finding correlations between the mechanical characteristics of fiber-reinforced soils such as indirect tensile strength(ITS)and California bearing ratio(CBR)and as well as the evaluation of shear strength parameters obtained from the triaxial test would be very effective at geotechnical construction sites.This research was aimed at investigating the influence of natural fibers as sustainable ones including basalt(BS)and bagasse(BG)as well as synthetic polyester(PET)fibers on the strength behavior of clayey soil.To this end,the effects of various fiber contents(0.5%,1%and 2%)and lengths(2.5 mm,5 mm and 7.5 mm)were experimentally evaluated.By conducting ITS and CBR tests,it was found that increasing fiber content and length had a significant influence on CBR and ITS values.Moreover,2%of 7.5 mm-long fibers led to the largest values of CBR and ITS.The CBR values of soil reinforced with PET,BS,and BG fibers were determined as 19.17%,15.43%and 13.16%,respectively.The ITS values of specimens reinforced with PET,BS,and BG fibers were reported as 48.57 kPa,60.7 kPa and 47.48 kPa,respectively.The results of the triaxial compression test revealed that with the addition of BS fibers,the internal friction angle increased by about 100%,and with the addition of PET fibers,the cohesion increased by about 70%.Moreover,scanning electron microscope(SEM)analysis was employed to confirm the findings.The relationship between CBR and ITS values,obtained via statistical analysis and used for the optimum design of road pavement layers,demonstrated that these parameters had high correlation coefficients.The outcomes of multiple linear regression and sensitivity analysis also confirmed that the fiber content had a greater effect on CBR and ITS values than fiber length.

Effect of low temperature treatment on tensile yield strength of SiC_w/6061 Al alloy composites

The effect of the low temperature treatment at -78 ℃ and -196 ℃ on the microstructure and properties of 18%SiC w/6061(volume fraction) Al alloy composites of as squeeze casting were studied. The results show that, after the low temperature treatment, the dislocation density in matrix increases, and the residual stress of the matrix decreases, as well as the tensile yield strength of the composites improves. The high residual stress exists in the matrix of the composites of as original squeeze casting. The mismatch degree between the matrix and SiC w phases increases during the low temperature treatment. The matrix undergoes the tensile plastic deformation during the cooling procedure. On the contrary, the matrix encountered an elastic unloading procedure during the heating up process from low temperature to room temperature. The increase of dislocation density and the decrease of residual stress in the matrix are the main reason of the improvement for tensile yield strength of the composites.

Distribution and tensile strength of Hornbeam （Carpinus betulus） roots growing on slopes of Caspian Forests, Iran

Biomechanical characteristics of the root system of hornbeam （Carpinus betulus） were assessed by measuring Root Area Ratio （RAR） values and tensile strength of root specimens of eight hornbeam trees growing on hilly terrain of Northern Iran. RAR values of the roots were obtained using profile trenching method at soil depth of the top 0.1 m. In total 123 root specimens were analyzed for tensile strength. Results indicate that in general, RAR decreases with depth, following a power function. The RAR values in up and down slopes have no significant statistical differences. In most cases, the maximum RAR values were located in soil depth of the top 0.1 m, with maximum rooting depth at about 0.75 m. The minimum and maximum RAR values along the profiles were 0.004% and 6.431% for down slope and 0.004% and 3.995% for up slope, respectively. The number of roots in the up and down slope trenches was not significantly different. In the same manner as for RAR, number of roots distributing with depth was satisfactorily approximated a power function. The penetration depths of above 90 percent of the roots were at soil depths of 50 cm and 60 cm for up and down slopes, respectively. Results of Spearman＇s bivariate correlation showed no significant correlation between the RAR value with tree diameter and gradient of slope and number of roots. The mean value of root tensile strength was 31.51 ± 1.05 MPa and root tensile strength decreased with the increase in root diameter, following a power law equation. Using ANCOVA, we found intraspecies variation of tensile strength.

Distribution and tensile strength of Hornbeam(Carpinus betulus) roots growing on slopes of Caspian Forests,Iran

Biomechanical characteristics of the root system of hornbeam(Carpinus betulus) were assessed by measuring Root Area Ratio(RAR) values and tensile strength of root specimens of eight hornbeam trees growing on hilly terrain of Northern Iran.RAR values of the roots were obtained using profile trenching method at soil depth of the top 0.1 m.In total 123 root specimens were analyzed for tensile strength.Results indicate that in general, RAR decreases with depth, following a power function.The RAR values in up and down slopes have no significant statistical differences.In most cases, the maximum RAR values were located in soil depth of the top 0.1 m, with maximum rooting depth at about 0.75 m.The minimum and maximum RAR values along the profiles were 0.004% and 6.431% for down slope and 0.004% and 3.995% for up slope, respectively.The number of roots in the up and down slope trenches was not significantly different.In the same manner as for RAR, number of roots distributing with depth was satisfactorily approximated a power function.The penetration depths of above 90 percent of the roots were at soil depths of 50 cm and 60 cm for up and down slopes, respectively.Results of Spearman's bivariate correlation showed no significant correlation between the RAR value with tree diameter and gradient of slope and number of roots.The mean value of root tensile strength was 31.51 ± 1.05 MPa and root tensile strength decreased with the increase in root diameter, follow-ing a power law equation.Using ANCOVA, we found intraspecies variation of tensile strength.

Effect of Surface Texture on Tensile Shear Strength of 1060Al-PET Welding Joints

Joining metal to plastic can lighten weight of products to reduce energy consumption.However,it is difficult to achieve high-strength welding between metal and plastic.To address this problem,the methods of surface texture pretreatment and laser irradiation welding was proposed to achieve the high-strength connection of metal and plastic.In this study,with different parameters of laser power and texture morphology,1060 Al with surface texture treatment was joined to polyethylene terephthalate(PET)by laser irradiation welding from metal side.Study showed that as the laser power increased,the tensile shear strength of joints increased first,and decreased thereafter.Tensile shear tests demonstrated that the mechanical force of joint was strengthened contributed to mechanical anchorage formed by surface texture.The depth-width ratio of the texture grooves affected the tensile shear process of the joint.According to the result of temperature simulation,the existence of texture grooves reduced the heat transfer efficiency,and the heat dissipation at interface was also impeded in course of laser welding.Finally,the maximum tensile strength of 1060Al-PET joint reached 48.4 MPa,which was close to the strength of PET matrix.The bonding mechanism of the 1060Al-PET joints was composed of mechanical bonding and chemical bonding.This study proposes an effective method to join metal to plastic which achieved high-strength connection between metal and plastic.

Influence of temperature on tensile behavior and deformation mechanism of Re-containing single crystal superalloy

Tensile properties of a Re-containing single crystal superalloy were determined within the temperature range from 20 to 1 100 ℃with a constant strain rate of 1.67 ×10^-4 s^-1.From room temperature to 600 ℃,the yield strength increases slightly with increasing temperature.The yield strength decreases to aminimum at 760 ℃,while a maximum is reached dramatically at 800 ℃.The elongation and area reduction decrease gradually from room temperature to 800 ℃.Above 800 ℃,the yield strength decreases significantly with increasing temperature.The γ＇ phase is sheared by antiphase boundary （APB） below 600 ℃while elongated SSF （superlattice stacking fault） is left in γ＇ as debris.At 760 ℃the γ＇ phase is sheared by a/3 112 superpartial dislocation,which causes decrease of yield strength due to low energy of SSF.Above 800 ℃dislocations overcome γ＇ through by-passing mechanism.

A STUDY OF THE SPECIMEN SIZE OF STRIP TENSILE TEST FOR NEEDLE-PUNCHED NON-WOVEN GEOTEXTILES

In this paper,the failure features of strip tensile specimen were observed and analysed for need-le-punched non-woven geotextiles.A mechanical model which expresses the relation between thetensile modulus,the strip specimen size,contraction factor and the tensile strength of non-wovenfabric was derived.The theoretical prediction showed that the main factor influencing tensilestrength of non-woven geotextile specimens with different size is the contraction factor of specimenor the specimen aspect ratio(width/length).The larger the aspect ratio,the higher the tensilestrength test value of geotextiles,but the experiments showed that the specimen tensile strength isnot increased with increasing the width of specimen.The reason was discussed and it seemed thatthe deviation could be served as an indication of the degree of imperfectness of the non-wovenstructure.

Effect of Aramid/Carbon Hybrid on the Tensile Properties of Multilayered Biaxial Weft Knitted Fabric Reinforced Composites

The effects of aramid/carbon on tensile properties of multilayered biaxial weft knitted( MBWK) fabric reinforced composites are analyzed by experiments. The tensile tests are inducted by the SHIMADZU AG-250 KNE universal material testing machine and Aramis V6 digital image correlation( DIC) technique.More specifically,the composite samples own four hybrid ratios(Na∶ Nc= 12∶ 0,8 ∶ 4,6 ∶ 6 and 4 ∶ 8). The results showed that the aramid/carbon hybrid MBWK fabric reinforced composites showed nearly linear response until reaching the maximum load and the inserting yarns distribution on the surface of MBWK fabrics reinforced composites had a great influence on the strain pattern distribution. Besides,the tensile strength,the tensile modulus and the elongation at breakage of 0° samples and 90° samples increased with the decreasing of aramid/carbon hybrid ratio. In a word,the changes of tensile strength, tensile modulus and elongation at breakage have a lot to do with the difference of aramid/carbon hybrid ratio.

Tensile and fracture behavior of DZ951 Ni-base superalloy

The tensile and fracture behavior of DZ951 directionally solidified Ni-base superalloy was studied in the temperature range of 20-1 100℃. The fracture mode was examined by scanning electron microscopy. The results show the experimental temperature has no significant effect on the tensile strengths, which are greater than 1 000 MPa from room temperature to 800℃. The yield strength reaches its maximum (970 MPa) at 800℃. When the experimental temperature is higher than 800℃, the tensile and yield strengths decrease evidently and the ductility increases remarkably. The fractograph of fracture surface for the tensile specimen at room temperature shows a dimple-ductile fracture mode. The fractograph from 600 to 800℃shows a slide fracture mode. The fractograph from 900 to 1 100℃exhibits a creep rupture mode with uneven deformation.

微磁检测技术在Cr12MoV钢和3Cr13钢屈服/抗拉强度检测中的应用

利用微磁无损检测方法对Cr12MoV钢和3Cr13钢的屈服强度(R_(p0.2))和抗拉强度(R_(m))进行无损定量预测。首先,采用先淬火后回火的工艺改变材料的拉伸力学性能,得到不同屈服/抗拉强度的拉伸试样;其次,对2种材料先后进行微磁特征参量测试和屈服/抗拉强度的测定;然后,分别利用格拉布斯(Grabbs)准则和ReliefF特征筛选方法,剔除系统误差并得到对强度指标敏感的微磁特征参量;最后,通过神经网络模型寻优,构建BP神经网络预测模型,实现Cr12MoV钢和3Cr13钢屈服强度和抗拉强度定量预测。研究结果表明:微磁检测方法可以对Cr12MoV钢和3Cr13钢屈服强度和抗拉强度进行无损定量预测,模型得到的屈服强度和抗拉强度预测平均误差分别小于3%和5%。提出的研究方法和结论可为铁磁性材料屈服强度和抗拉强度的微磁无损检测提供参考。

沙漠砂纤维陶粒混凝土力学性能试验研究

为研究沙漠砂纤维轻骨料混凝土(DPFLWC)的力学性能,通过不同掺量的聚丙烯纤维混凝土进行28 d抗压强度、劈拉强度的试验研究。探讨了劈拉强度、抗压强度在不同纤维掺量下的变化规律;构建了劈拉强度与抗压强度关系的计算模型。结果表明:其抗压强度、劈拉强度均随纤维掺量的增加呈先增后减的规律,当纤维掺量较高时,其强度增长率降低;能量耗散分析表明聚丙烯纤维起到了增韧作用,提高了耗能能力;结合现有文献数据验证了劈拉强度与抗压强度的换算关系的可靠性;其结果可为沙漠砂纤维陶粒混凝土在工程上的应用提供参考。

Yield and mechanical properties of veneer from Brachystegia nigerica

In an effort to find suitable wood from natural forest to meet the demand for veneer products, the yield and tensile strength of veneers produced from Brachystegia nigerica were investigated. Two trees of B. nigerica were separately selected from 10 different natural forest zones while two logs were obtained from each tree. The logs were debarked and steamed in a vat prior to rotary peeling and slicing for veneer production. The optimum steam temperature was determined by considering different temperatures： 50℃, 60℃, 70℃, 80℃ and 90℃ for 24 h. Thereafter, optimum steam time was determined at the optimum temperature by considering durations of 24, 48, 72 and 96 h. The average taper of 0.75 mm per 1.0 m length was recorded for B. nigerica, indicating that the logs were reasonably cylindrical; thereby its logs are good for the production of veneer. The yield ranged from 44% to 61% with an average of 52% of the log input. The tensile strength of the veneer was tested perpendicular to grain and both peeled and sliced veneers had the highest tensile strength between 70℃ and 90℃, suggesting that softening of wood polymers, especially lignin, is between 70℃ and 90℃. The optimum temperature and time for veneer production are 70℃ and 48 h, respectively. Commercial production of veneer from B. nigerica is feasible based on the yield and mechanical properties of the obtained veneer, thereby encouraging the expansion of the scope of its utilization.

Mechanical characteristics of tensile strength ratio method compared to other parameters used for moisture susceptibility evaluation of asphalt mixtures

In this study,mechanical characteristics of tensile strength ratio(TSR)were evaluated by comparing it to other methods in evaluating moisture sensitivity of asphalt mixtures.Twenty types of asphalt mixtures with and without anti-stripping additives were prepared and tested in the laboratory.Uniaxial compressive strength(UCS)and indirect tensile(IDT)testing were conducted to determine the mixture’s tensile strength ratio and cohesion ratio(CR).Determining TSR alone was found to be insufficient when evaluating moisture resistance.There is a need to consider both TSR and wet IDT strength to properly evaluate moisture behavior of asphalt mixtures.Moreover,it was found that the cohesion and the IDT strength have a good relation in which the minimum condition of the slope,must be met.However,it was observed thatβvalues change depending on material type and temperature.Hence,there is a need to evaluate theseβvalues for varying material and testing temperature.In addition,it was found that the TSR and CR results are highly correlated with an average difference of 1.5%.Furthermore,other tests such as Marshall stability and dynamic immersion were also conducted.It was found that Marshall stability ratio(MSR)and Marshall stability to flow ratio(MSFR)values are less sensitive to moisture effect when measuring moisture resistance compared to TSR values.Finally,the 48 h testing result of the dynamic immersion test showed better correlation with TSR values.

TENSILE STRENGTH FOR SPLITTING FAILURE OF BRITTLE PARTICLES WITH CONSIDERATION OF POISSON'S RATIO

The core mechanism of comminution could be reduced to the breakage of individual particles that occurs through contact with other particles or with the grinding media, or with the solid walls of the mill. When brittle particles are loaded in compression or by impact, substantial tensile stresses are induced within the particles. These tensile stresses are responsible for splitting failure of brittle particles. Since many engineering materials have Poissons ratios very close to 0.3, the influence of Poissons ratio on the tensile strength is neglected in many studies. In this paper, the state of stress in a spherical particle due to two diametrically opposed forces is analyzed theoretically. A simple equation for the tensile stress at the centre of the particle is obtained. It is found reasonable to propose this tensile stress at the instant of failure as the tensile strength of the particle. Moreover, this tensile strength is a function of the Poissons ratio of the material. As the state of stress along the z-axis in an irregular specimen tends to be similar to that in a spherical particle compressed diametrically with the same force, this tensile strength has some validity for irregular particles as well. Therefore, it could be used as the tensile strength for brittle particles in general. The effect of Poissons ratio on the ten-sile strength is discussed.

Influence of recrystallized microstructure on the mechanical properties of cold rolled microalloy high strength steel

Because of the influence of Nb-educts in cold rolled Nb-microalloy high strength steel manufactured by a continuous annealing unit, different quantities of non-recrystallized ferrite exist in the material, which leads to great fluctuation of mechanical behavior of the material. In this study, the relationship between non-recrystallized ferrite and mechanical properties is analyzed, and some factors influencing the formation of non-recrystallized ferrite are also studied.

Machine Learning Design of Aluminum-Lithium Alloys with High Strength

Due to the large unexplored compositional space,long development cycle,and high cost of traditional trial-anderror experiments,designing high strength aluminum-lithium alloys is a great challenge.This work establishes a performance-oriented machine learning design strategy for aluminum-lithium alloys to simplify and shorten the development cycle.The calculation results indicate that radial basis function(RBF)neural networks exhibit better predictive ability than back propagation(BP)neural networks.The RBF neural network predicted tensile and yield strengths with determination coefficients of 0.90 and 0.96,root mean square errors of 30.68 and 25.30,and mean absolute errors of 28.15 and 19.08,respectively.In the validation experiment,the comparison between experimental data and predicted data demonstrated the robustness of the two neural network models.The tensile and yield strengths of Al-2Li-1Cu-3Mg-0.2Zr(wt.%)alloy are 17.8 and 3.5 MPa higher than those of the Al-1Li4.5Cu-0.2Zr(wt.%)alloy,which has the best overall performance,respectively.It demonstrates the reliability of the neural network model in designing high strength aluminum-lithium alloys,which provides a way to improve research and development efficiency.

氯盐环境下钢筋HRB400的腐蚀行为与力学性能研究

为了给工程安全使用提供借鉴,采用浸泡腐蚀法研究钢筋HRB400在3.5%NaCl溶液中裸露和镶入混凝土2种环境下腐蚀行为及腐蚀后的力学性能,对于钢筋HRB400镶入混凝土这种环境,采用制作钢筋混凝土及模拟混凝土孔隙液2种方法,首先将裸露和镶入混凝土2种情况下的钢筋HRB400浸泡在3.5%(质量分数)NaCl溶液中,并将钢筋HRB400浸泡在饱和氢氧化钙溶液中[加入3.5%(质量分数)NaCl溶液],然后分别计算不同腐蚀时间下各钢筋HRB400相应的失重率、腐蚀率,最后采用MTS试验机测试钢筋HRB400腐蚀后的力学性能。结果显示:随着浸泡腐蚀时间延长,3种环境下的钢筋HRB400平均腐蚀速率逐渐降低,失重率增加,屈服强度、抗拉强度均下降,钢筋HBR400在3.5%NaCl溶液中裸露或镶入混凝土时伸长率随浸泡时间延长而降低,在饱和氢氧化钙(加入3.5%NaCl)中则呈现有升有降趋势。

高强页岩轻骨料混凝土制备及微观结构研究

基于最紧密堆积理论和最小需水量法进行高强页岩轻骨料混凝土配合比设计与制备,研究了水胶比对抗压及劈裂抗拉强度影响,并借助SEM/EDS进行微观测试分析。结果表明:当粗细骨料体积分数比为5.5:4.5时,粗细骨料达到最紧密堆积状态;当硅灰、粉煤灰和水泥质量比为0.8:3.2:6时,需水量最少,粉体材料密实度最佳;依据优化配比所配混凝土的抗压强度和劈裂抗拉强度均随龄期增加而增加;随着水胶比增加,抗压强度和劈裂抗拉强度呈先增后减的趋势,且当水胶比为0.24时达到最大,分别为70.9、5.83MPa;硅灰和粉煤灰特有的形态效应和火山灰效应有效改善了浆体与骨料间界面的密实程度,微观结果显示浆体与骨料界面区域结构致密,陶粒区域为富Si、Al相,浆体一侧为富Ca相。

Cu-4Ag合金微细丝拉拔极限预测模型

采用三室真空冷型竖引连铸设备制备了Cu-4Ag合金铸态杆坯,并利用连续冷拉拔变形得到了不同线径的Cu-4Ag合金微细丝,通过拉拔实验获取了不同线径下材料的屈服强度和抗拉强度;基于线径与强度的关系,构建了微细丝拉拔极限预测模型。结果表明,在拉拔过程中,Cu-4Ag合金微细丝的线径与抗拉强度密切相关,具有明显的尺寸效应;修正后的拉拔极限模型能够较为准确地预测不同线径的Cu-4Ag合金微细丝能够达到的拉拔极限。将拉拔极限模型产出的数据导入MATLAB中,构建了三维曲面模型,可以更为直观地分析材料的拉拔极限。