CONTROL OF TWO DIMENSIONAL JETS USING MINIATURE ZERO MASS FLUX JETS

Zero mass flux jets, synthesized by acoustic actuators, have been used for the purpose of jet mixing enhancement and jet vectoring. Zero mass flux jets composed of entirely entrained fluid allow momentum transfer into the embedding flow. In the present experiments, miniature scale high aspect ratio actuator jets are placed along the long sides and near the exit plane of a primary two dimensional jet. In different modes, the primary jet can be vectored either towards or away from the actuator jets and the jet mixing is enhanced. The disturbance of the excitation frequency is developed while the unstable frequency of the primary jet is completely suppressed.

Heat Flux Characterization of DC Laminar-plasma Jets Impinging on a Flat Plate at Atmospheric Pressure

By using steady and transient methods, the total heat fluxes and the distributions of the heat flux were measured experimentally for an argon DC laminar plasma jet impinging normally on a flat plate at atmospheric pressure. Results show that the total heat fluxes measured with a steady method are a little bit higher than those with a transient method. Numerical simulation work was executed to compare with the experimental results.

Critical Heat Flux in Forced Convective Boiling with a Wall Jet

The critical heat flux (CHF) in the forced convective boiling with a wall jet has been investigated.The experiments of CHF with a wall jet have been performed over a wide range of ρ l/ρ g=6.6-1 603 and ΔT sub =0-60 K. The mechanism on CHF is discussed and a CHF model based on heat balance in sublayer can provide a good clue for analyzing and deriving CHF.Finally,a generalized correlation is presented, which can predict CHF for saturated and subcooled conditions.

Investigations on the Heat Flux Rates in Superheated Water Jet Evaporators

When a liquid undergoes sudden reduction in the surrounding pressure below its saturation pressure, the liquid then enters in a metastable state. In order to regain equilibrium, part of the liquid evaporates quickly in a phenomenon called ＂flash evaporation＂, and the excess sensible heat contained in the liquid is converted into latent heat of vaporization. Therefore, temperatures of both the liquid and the generated vapor decline to the saturation temperature for the reduced pressure. As the heat and mass transfer occur in direct contact between the liquid and its own vapors, the process involves a very high heat transfer rate which makes it suitable for exchanging heat between sources of relatively small temperature difference. Moreover, dispensability of the heat exchange surfaces in this process is a considerable advantage as these surfaces constitute major part of the total system expenses in addition to the associated maintenance problems, especially when dealing with corrosive fluids such like seawater in the thermal desalination processes and in the OTEC （ocean thermal energy conversion） systems. This paper reports on the heat flux variation profiles during the flash evaporation of superheated water jets at various flow conditions. Heat flax was found to grow with time attaining a peak value before it starts to decrease monotonically.

热风加热沥青路面冲击射流共轭传热特性

为提高热风加热沥青路面的就地再生加热效果,基于热风冲击射流对流换热和沥青路面内部导热的共轭传热过程,建立了热风加热沥青路面的冲击射流共轭传热理论模型,选取有限容积法得到了共轭传热模型的通用离散方程,采用压力-速度耦合半隐式算法(semi-implicit method for pressure linked equations,SIMPLE)获得了整个求解域内温度场分布,选取平均热流密度和平均换热系数反映沥青路面加热效果,通过正交试验研究了热风出口速度和热风出口温度对路面加热效果的影响程度。仿真和试验结果表明:理论计算与实验温度场分布趋势吻合度高,两者平均误差为8.4%;平均热流密度和平均换热系数在加热初期均从最大值急剧下降,而后下降幅度逐渐减小趋于平衡,两者的仿真计算与实验结果趋势相同,平均误差分别为6.4%和7.8%;热风出口速度和热风出口温度对平均热流密度均有显著影响,热风出口速度对平均换热系数有显著影响,热风出口温度对平均换热系数的影响相较于平均热流密度指标表现为不显著。研究结果为后续沥青路面就地热再生热风加热温度控制和加热器设计提供了理论依据。

零质量射流下波浪前缘叶片气动性能数值研究

针对垂直轴风机叶片大攻角工况下因流动分离导致的失速及颤振抖振问题,引入零质量射流激励对波浪型前缘叶片进行流动分离控制.采用大涡模拟方法建立了波浪前缘叶片绕流数值模型,探究了主/被动耦合控制下叶片升阻力特性及其流动分离机理,分析了射流参数(射流位置、动量系数)对波浪前缘叶片气动性能及失速特性的影响机制,研究发现:受控前后大攻角下波浪型前缘能诱导产生较小尺度流向涡,降低后方大分离涡尺度,波浪前缘与零质量射流耦合控制对于大攻角下流动分离抑制较单一控制更优;零质量射流吹气时使前缘流向涡有更高的动能抵抗逆压梯度从而延迟流动分离,吸气时会吸走流向涡的低动量流体,抑制流向涡发展成大分离涡;射流布置在距基准前缘0.033c处,即位于前缘流向涡最前端,能最大程度地参与前缘流向涡的生成,升阻比的提升效果最好;且升阻比提升量随着动量系数增大而增大,但控制经济性在动量系数0.018时最优,研究结果为垂直轴风力机失速控制提供了有益参考.

FGOALS-s2 Simulation of Upper-level Jet Streams over East Asia: Mean State Bias and Synoptic-scale Transient Eddy Activity

Upper-level jet streams over East Asia simulated by the LASG/IAP coupled climate system model FGOALS-s2 were assessed, and the mean state bias explained in terms of synoptic-scale transient eddy activ- ity （STEA）. The results showed that the spatial distribution of the seasonal mean jet stream was reproduced well by the model, except that following a weaker meridional temperature gradient （MTG）, the intensity of the jet stream was weaker than in National Centers for Environment Prediction （NCEP）/Department of Energy Atmospheric Model Inter-comparison Project II reanalysis data （NCEP2）. Based on daily mean data, the jet core number was counted to identify the geographical border between the East Asian Sub- tropical Jet （EASJ） and the East Asian Polar-front Jet （EAPJ）. The border is located over the Tibetan Plateau according to NCEP2 data, but was not evident in FGOALS-s2 simulations. The seasonal cycles of the jet streams were found to be reasonably reproduced, except that they shifted northward relative to reanalysis data in boreal summer owing to the northward shift of negative MTGs. To identify the reasons for mean state bias, the dynamical and thermal forcings of STEA on mean flow were examined with a focus on boreal winter. The dynamical and thermal forcings were estimated by extended Eliassen-Palm flux （E） and transient heat flux, respectively. The results showed that the failure to reproduce the tripolar-pattern of the divergence of E over the jet regions led to an unsuccessful separation of the EASJ and EAPJ, while dynamical forcing contributed less to the weaker EASJ. In contrast, the weaker transient heat flux partly explained the weaker EASJ over the ocean.

Teleconnected Influence of the Boreal Winter Antarctic Oscillation on the Somali Jet： Bridging Role of Sea Surface Temperature in Southern High and Middle Latitudes

The teleconnection impact of the boreal winter Antarctic Oscillation（AAO） on the Somali Jet（SMJ） intensity in the following spring and summer is examined in this paper.The variability of the boreal winter AAO is positively related to the SMJ intensity in both spring and summer.The analyses show that the SST in southern high and middle latitudes seems to serve as a bridge linking these two systems.When the AAO is in strong positive phase,SST over the Southern Ocean cools in the high latitudes and warms in the middle latitudes,which persists into summer;however,the variability of SST in southern high and middle latitudes is also closely correlated to SMJ intensity.A possible mechanism that links SST variability with the AAO-SMJ relationship is also discussed.The AAO in boreal winter produces an SST anomaly pattern in southern high and middle latitudes through the air-sea coupling.This AAOrelated SST anomaly pattern modulates the local Ferrel cell anomaly in summer,followed by the regional Hadley cell anomaly in tropics.The anomalous vertical motion in tropics then changes the land-sea thermal contrast between the tropical Indian Ocean and the Asian continent through the variability of low cloud cover and downward surface longwave radiation flux.Finally,the land-sea thermal contrast anomaly between the tropical Indian Ocean and the Asian continent changes the SMJ intensity.The results from Community Atmosphere Model experiments forced by the SST anomaly in southern high and middle latitudes also confirm this diagnostic physical process to some extent.

Nonequilibrium Atmospheric Pressure Ar/O_2 Plasma Jet:Properties and Application to Surface Cleaning

In this study an atmospheric pressure Ar/O_2 plasma jet is generated to study the effects of applied voltage and gas flux rate to the behavior of discharge and the metal surface cleaning.The increase in applied voltage leads to increases of the root mean square（rms） current,the input power and the gas temperature.Furthermore,the optical emission spectra show that the emission intensities of metastable argon and atomic oxygen increase with increasing applied voltage.However,the increase in gas flux rate leads to a reduction of the rms current,the input power and the gas temperature.Furthermore,the emission intensities of metastable argon and atomic oxygen decrease when gas flux rate increases.Contact angles are measured to estimate the cleaning performance,and the results show that the increase of applied voltage can improve the cleaning performance.Nevertheless,the increase of gas flux rate cannot improve the cleaning performance.Contact angles are compared for different input powers and gas flux rates to search for a better understanding of the major mechanism for surface cleaning by plasma jets.

Analysis of disagreement between numerically predicted and experimental heat transfer data of impinging jet

The method of numerical simulation was applied to investigate the effects of jet impinging plate thickness and its thermal conductivity on the local heat flux distribution along the impinging plate. The results show that the two factors have great effects on the heat flux distribution. The non-uniformity of the local heat-flux on the impinging plate surface gets more profound as the plate becomes thicker and thermal conductivity gets larger. When Reynolds number is 5000, the ratio of nozzle-to-plate spacing to nozzle diameter is 5 and thermal conductivity is 16W/(m·K), and even for the plate with only 25μm in thickness, the non-uniformity of the heat flux cannot be neglected. When the plate thickness is 50 μm, only when thermal conductivity is as small as 1W/(m·K), the heat flux curve can be approximately treated as an iso-heat-flux boundary. In the experimental research, a real non-iso-heat-flux boundary is treated as an iso-heat-flux boundary, which would result in under-estimated Nusselt number value in the stagnation zone and an over-estimated value outside. Such an experimental Nusselt number distribution is taken to evaluate turbulent model, and the conclusion would be drawn that the turbulent model over-predicts the stagnation heat transfer. This is one of the important reasons why many literatures reported that k-ε turbulent model dramatically over-predicts the impinging jet heat transfer in the stagnation region.

New Formulation for Semi-Empirical Correlations for Penetration Jets

Correlations for the extension of a water vapor jet injected in a liquid pool were historically proposed considering the mass flux (kg/m2/s) as a constant. The results were satisfactory, however adjusting the values by linear regression. Although, it presents the following drawbacks: 1) the formulation is only valid for the specific range of data for what it was created;2) it does not allow the analytical evaluation of the heat transfer coefficient from the extension equation. This paper proposes a new formulation for the calculation of the mass flux, in such a way to remove both of these drawbacks.

局部高热流密度器件射流冲击冷板流动传热特性数值研究

为解决大功率雷达等设备中存在的局部高热流密度热管理难题,进行了大幅面、非均匀高热流密度散热技术研究,提出了一种可同时对上下两侧发热面进行冷却的嵌入式射流冲击冷板,开展了受限空间射流冲击冷却过程流动换热特性数值模拟,获得了嵌入式射流冲击冷板内部的流动换热特性,并对射流冲击距离、射流孔直径、冷板体积流量等参数对流动换热性能的影响规律进行了分析。结果表明,对尺寸为50 mm×72 mm、背景热流密度为1.2 W/cm^(2)、布置有8个3 mm×3.5 mm、125 W/cm^(2)高热流密度芯片的发热面,嵌入式射流冲击冷板的换热系数分布特点可满足局部高热流密度散热需求,且在射流冲击距离为3 mm、射流孔直径为2 mm时,综合考虑换热性能与压降后的冷板性能最佳,在冷板体积流量为5.5 L/min时,芯片最大温升为15.6℃,压降为3.917 kPa。所提嵌入式射流冲击冷板及研究结果可用于局部高热流密度器件热管理。

电磁能与炸药联合加载药型罩基础理论

为提高聚能射流对炸药能量的利用率,结合电磁加载药型罩以及爆磁压缩发生器原理,提出一种电磁能与炸药联合加载药型罩的原理结构。联合加载分为两个阶段:第1阶段,电容器放电,在爆磁压缩发生器中形成初始磁通;第2阶段,炸药1爆轰,压缩磁场,电流增大,同时爆轰波传播至药型罩部分引爆炸药2,电磁力与爆轰压力共同压垮药型罩。结合炸药爆轰理论、传统PER射流成型理论以及电磁加载特性,建立电磁与炸药联合加载下药型罩射流成型的理论模型。利用理论模型计算?56 mm聚能装药在联合加载结构下的射流成型,并通过理论计算分析联合加载时序对联合加载射流成型的影响。计算结果表明:电磁与炸药联合加载能够增加成型射流的速度以及动能,提高聚能射流对炸药的利用率,并且优化联合加载时序能够进一步提高射流速度和动能;联合加载下射流动能相对传统聚能装药提升了34.5%,对炸药的能量利用率提高了36%。

Characteristics of the plasma sheath in helium discharge within dielectric tubes

To understand the characteristics of the plasma sheath within small tubes,a 2D numerical model of He discharge within dielectric tubes is developed.During plasma propagation for a tube diameter of 0.05 mm,the sheath thickness in the plasma head is almost equal to the tube radius.It decreases rapidly to several micrometers at an axial distance of 0.05 mm behind the plasma head,and then slightly increases and saturates at the axial position far behind the plasma head.A plasma-gas sheath surrounding the central plasma column is observed for a tube diameter equal to or greater than 0.8 mm.It is replaced by a plasma-wall sheath for smaller tubes.With the decrease in the tube diameter,the sheath thickness far behind the plasma head decreases while the ion flux increases significantly.However,when O_(2)gas with a proportion of 2%is added,both the sheath thickness and ion flux decrease.

Numerical Investigation of Jet Impingement Cooling with Supercritical Pressure Carbon Dioxide in a Multi-Layer Cold Plate during High Heat Flux

Jet impingement cooling with supercritical pressure carbon dioxide in a multi-layer cold plate during the heat flux of 400 W/cm_(2) is investigated numerically.The generation and distribution of pseudocritical fluid with the high specific heat of supercritical pressure carbon dioxide and the mechanism of the heat transfer enhancement led by the high specific heat are analyzed.For a given nozzle diameter,the effects of the geometric parameters of a multi-layer cold plate such as the relative nozzle-to-plate distance,relative plate thickness,and relative upper fluid thickness on the average heat transfer coefficient are studied.The results show that the target surface is cooled effectively with supercritical pressure carbon dioxide jet impingement cooling.When the radial distance is less than 6 mm,the maximum wall temperature is 368 K,which is 30 K lower than the maximum junction temperature for a silicon-based insulated gate bipolar transistor,a typical electronic power device.There is a pseudocritical fluid layer near the target surface,where specific heat reaches above 34 kJ/(kg·K)locally.The drastic rise of the specific heat leads to obvious heat transfer enhancement.Within a certain range,the local heat transfer coefficient and the specific heat are linearly correlated and Stanton number remains constant over this range.The heat transfer coefficient is at a maximum when the relative nozzle-to-plate distance is 1.As the relative plate thickness increases from 0.5 to 3.5 or the relative upper fluid thickness increases from 0.5 to 2.5,the average heat transfer coefficient decreases monotonically.

Contrasting Regional Responses of Indian Summer Monsoon Rainfall to Exhausted Spring and Concurrently Emerging Summer El Nino Events

The inverse relationship between the warm phase of the El Nino Southern Oscillation(ENSO)and the Indian Summer Monsoon Rainfall(ISMR)is well established.Yet,some El Nino events that occur in the early months of the year(boreal spring)transform into a neutral phase before the start of summer,whereas others begin in the boreal summer and persist in a positive phase throughout the summer monsoon season.This study investigates the distinct influences of an exhausted spring El Nino(springtime)and emerging summer El Nino(summertime)on the regional variability of ISMR.The two ENSO categories were formulated based on the time of occurrence of positive SST anomalies over the Nino-3.4 region in the Pacific.The ISMR’s dynamical and thermodynamical responses to such events were investigated using standard metrics such as the Walker and Hadley circulations,vertically integrated moisture flux convergence(VIMFC),wind shear,and upper atmospheric circulation.The monsoon circulation features are remarkably different in response to the exhausted spring El Nino and emerging summer El Nino phases,which distinctly dictate regional rainfall variability.The dynamic and thermodynamic responses reveal that exhausted spring El Nino events favor excess monsoon rainfall over eastern peninsular India and deficit rainfall over the core monsoon regions of central India.In contrast,emerging summer El Nino events negatively impact the seasonal rainfall over the country,except for a few regions along the west coast and northeast India.

Combustion Characteristics of Solid Sustained-Release Energetic Materials

A solid sustained-release energetic material sample,an eruption device and a complete test system were prepared further to analyse the combustion characteristics of solid sustainedrelease energetic materials.The high-temperature heat flux generated by the combustion of the samples from the eruption device was used to penetrate the Q235 target plate.In addition,the meaning and calculation formula of energy density characterising the all-around performance of heat flux were proposed.The numerical simulation of the combustion effect of samples was carried out.According to the data comparison,the numerical simulation results agreed with the experimental results,and the maximum deviation between the two was less than 8.9%.In addition,the structure of the combustion wave and high-temperature jet was proposed and analysed.Based on theoretical analysis,experimental research and numerical simulation,the theoretical burning rate formula of the sample was established.The maximum error between the theoretically calculated mass burning rate and the experimental results was less than 9.8%.Therefore,using the gas-phase steady-state combustion model to study the combustion characteristics of solid sustained-release energetic materials was reasonable.The theoretical burning rate formula also had high accuracy.Therefore,the model could provide scientific and academic guidance for the theoretical research,system design and practical application of solid sustained-release energetic materials in related fields.

应用PIV技术研究“零质量”射流的非定常流场特性

首次采用PIV瞬态流场测试技术对"零质量"射流激振器近出口处附近的非定常流场进行了定量测量,应用相位锁定采样技术,测到了激励周期内不同相位时射流出口的瞬态流场,由200幅瞬态流场图像的平均得到了射流流场的平均流动特性。通过对射流出口涡环的产生、发展及运动特性的分析,认识到涡环之间相互作用是形成"零质量"射流的流动机理。

不同狭缝厚度的零质量射流PIV实验研究

为了研究厚度对活塞型激励器产生的零质量射流流场的影响,利用粒子影像测速仪对h=1.5 mm,2mm和3.5 mm三种不同狭缝厚度的零质量射流流场进行了实验研究。采用相位锁定技术,在一个振动周期内捕捉了12个不同相位时刻的流场图片。实验发现,合成射流时间平均流场的横向速度剖面与二维常规射流相似,具有自模化特性;合成射流的质量通量、动量通量、中心线速度的峰值与狭缝厚度成正比。随着狭缝厚度增加,与质量通量和动量通量峰值相应的距出口的无量纲距离减小,而与中心线速度峰值相对应的无量纲距离增加。

二维合成射流组合效应的数值研究

采用数值模拟的方法,研究了一列合成射流对二维平板流动壁面的影响,对合成射流组合效应进行了分析。结果表明:在不同的开孔角度和振动相位下,合成射流组合效应明显,对壁面平均剪切应力改变显著,最大变化约15%,对壁面压力改变较小,最大变化约0.5%,;对于流场壁面压力和剪切应力分布,斜开孔比直开孔改变要大,异相位射流比同相位射流改变要大;异相位振动模式下,壁面平均压力和剪切应力值波动较小,变化比较平稳。