Minimizing pest aluminum in magnesium for the production of high-purity titanium

It is practically difficult to find titanium sponges with low and stable aluminum impurities on the market even though it is the precondition to prepare high-purity titanium. Analysis indicates that almost all the aluminum impurities in the titanium sponge are inherited from the magnesium used to reduce titanium tetrachloride. However, it remains elusive for decades why magnesium produced through the silicothermic reduction method contains a high content of aluminum impurities with large fluctuations. By recourse to thermodynamic calculations and comparative experiments, we demonstrate that fluorite, a material used as a catalyst in the silicothermic reduction method to produce magnesium, is the chief culprit for the pest aluminum and propose a mechanism to rationalize the observed phenomena. Our findings indicate that one practical way to produce qualified magnesium for the production of high-purity titanium is to abandon fluorite during the production of magnesium with the silicothermic reduction method.

Effect of heat diffusion on properties of zinc-aluminum coating on AZ91D magnesium alloys

A protecting zinc and aluminum coating on the surface of AZ91D magnesium alloys was obtained by thermal spraying to improve the corrosion and wear resistance performances. In order to enhance the combination between magnesium alloy matrix and zinc and aluminum coating, the sample was heat-treated at 300℃for 2 h, then, the cross-section patterns, XRD pattern, micro-hardness, wear and corrosion resistance abilities were researched. The results indicate that the interface between the coating and substrate is metallurgical bond, and a transitional fusion layer is formed by diffusion. The micro-scale abrasion test and polarization test in 3% NaCl solution show that the diffusion-treated specimen has better wear and corrosion resistance performances in comparison with the undiffusion-treated and substrate magnesium alloys; in addition, it has relatively higher micro-hardness than the undiffusion-treated magnesium alloys.

Predicting and controlling interfacial microstructure of magnesium/aluminum bimetallic structures for improved interfacial bonding

In this study,an overcasting process followed by a low-temperature(200°C)annealing schedule has been developed to bond magnesium to aluminum alloys.ProCAST software was used to optimize the process parameters during the overcasting process which lead to Mg/Al bimetallic structures to be successfully produced without formation of Mg-Al intermetallic phases.Detailed microstructure evolution during annealing,including the formation and growth of Al-Mg interdiffusion layer and intermetallic phases(Al12Mg17 and Al3Mg2),was experimentally observed for the first time with direct evidence,and predicted using Calculation of Phase Diagrams(CALPHAD)modeling.Maximum interfacial strength was achieved when the interdiffusion layer formed at the Mg/Al interface reached a maximum thickness the without formation of brittle intermetallic compounds.The precise diffusion modeling of the Mg/Al interface provides an efficient way to optimize and control the interfacial microstructure of Mg/Al bimetallic structures for improved interfacial bonding.

Determining the microstructure and properties of magnesium aluminum composite panels by hot rolling and annealing

The researchers made magnesium aluminum composite panels by asymmetric metal packaging and studied rolling temperature,holding time,and high temperature heat treatment,such as short time and low temperatures over long periods of time parameters under the new preparation method.We tested the new magnesium aluminum composite panels’tensing properties and bending performance by using scanning electric mirror and EDS.It is concluded that the new magnesium aluminum composite panels’elongation is 24%under the tensile strength of 260 MPa.Regarding performance when compared with other methods,traditional magnesium aluminum composite panels’elongation is 10%,which shows its advanced nature.At the same time,bending performance test showed that the combination of the composite board has higher performance,offering the reference value for the preparation of magnesium–aluminum composite plate.

Microstructural analyses of aluminum–magnesium–silicon alloys welded by pulsed Nd: YAG laser welding

Revealing grains and very fine dendrites in a solidified weld metal of aluminum–magnesium–silicon alloys is difficult and thus,there is no evidence to validate the micro-and meso-scale physical models for hot cracks. In this research, the effect of preheating on the microstructure and hot crack creation in the pulsed laser welding of AA 6061 was investigated by an optical microscope and field emission electron microscopy. Etching was carried out in the gas phase using fresh Keller’s reagent for 600 s. The results showed that the grain size of the weld metal was proportional to the grain size of the base metal and was independent of the preheating temperature. Hot cracks passed the grain boundaries of the weld and the base metal. Lower solidification rates in the preheated samples led to coarser arm spacing;therefore, a lower cooling rate. Despite the results predicted by the micro and meso-scale models, lower cooling rates resulted in increased hot cracks. The cracks could grow in the weld metal after solidification;therefore, hot cracks were larger than predicted by the hot crack prediction models.

Improving mechanical properties of AZ91D magnesium/A356 aluminum bimetal prepared by compound casting via a high velocity oxygen fuel sprayed Ni coating

In this paper,a Ni coating was deposited on the surface of the A356 aluminum alloy by high velocity oxygen fuel spraying to improve the performance of the AZ91D magnesium/A356 aluminum bimetal prepared by a compound casting.The effects of the Ni coating as well as its thickness on microstructure and mechanical properties of the AZ91D/A356 bimetal were systematically researched for the first time.Results demonstrated that the Ni coating and its thickness had a significant effect on the interfacial phase compositions and mechanical properties of the AZ91D/A356 bimetal.The 10μm’s Ni coating cannot prevent the generation of the Al-Mg intermetallic compounds(IMCs)at the interface zone of the AZ91D/A356 bimetal,while the Ni coating with the thickness of 45μm and 190μm can avoid the formation of the Al-Mg IMCs.When the Ni coating was 45μm,the Ni coating disappeared and transformed into Mg-Mg_(2)Ni eutectic structures+Ni_(2)Mg_(3)Al particles at the interface zone.With a thickness of 190μm’s Ni coating,part of the Ni coating remained and the interface layer was composed of the Mg-Mg_(2)Ni eutectic structures+Ni_(2)Mg_(3)Al particles,Mg_(2)Ni layer,Ni solid solution(SS)layer,Al_(3)Ni_(2) layer,Al_(3)Ni layer and sporadic Al_(3)Ni+Al-Al_(3)Ni eutectic structures from AZ91D side to A356 side in sequence.The interface layer consisting of the Mg-Ni and Al-Ni IMCs obtained with the Ni coating had an obvious lower hardness than the Al-Mg IMCs.The shear strength of the AZ91D/A356 bimetal with a Ni coating of 45μm thickness enhanced 41.4%in comparison with that of the bimetal without Ni coating,and the fracture of the bimetal with 45μm’s Ni coating occurred between the Mg matrix and the interface layer with a mixture of brittle fracture and ductile fracture.

Optimal dose of zinc supplementation for preventing aluminum-induced neurotoxicity in rats

Zinc supplementation can help maintain learning and memory function in rodents. In this study, we hypothesized that zinc supplementation could antagonize the neurotoxicity induced by aluminum in rats. Animals were fed a diet containing different doses of zinc （50, 100, 200 mg/kg） for 9 weeks, and orally administered aluminum chloride （300 mg/kg daily） from the third week for 7 consecutive weeks. Open-field behavioral test results showed that the number of rearings in the group given the 100 mg/kg zinc supplement was significantly increased compared with the group given the 50 mg/kg zinc supplement. Malondialdehyde content in the cerebrum was significantly decreased, while dopamine and 5-hydroxytryptamine levels were increased in the groups given the diet sup- plemented with 100 and 200 mg/kg zinc, compared with the group given the diet supplemented with 50 mg/kg zinc. The acetylcholinesterase activity in the cerebrum was significantly decreased in the group given the 100 mg/kg zinc supplement. Hematoxylin-eosin staining revealed evident patho- logical damage in the hippocampus of rats in the group given the diet supplemented with 50 mg/kg zinc, but the damage was attenuated in the groups given the diet supplemented with 100 and 200 mg/kg zinc. Our findings suggest that zinc is a potential neuroprotective agent against alumi-num-induced neurotoxicity in rats, and the optimal dosages are 100 and 200 mg/kg.

Galvanic Corrosion of Magnesium Alloy and Aluminum Alloy by Kelvin Probe

Galvanic corrosion on samples of AZ91D magnesium alloy coupled with 2A12 aluminum alloy during neutral salt spray test was investigated.The variations of the surface potential were measured using scanning kelvin probe（SKP）.The results showed that galvanic effect on the corrosion of AZ91D magnesium alloy is closely related to the potential difference between the anodic and cathodic materials.In the initial period,corrosion only occurred in a narrow area at the coupling interface because of the limited distance galvanic current.Then,the corrosion rate of 2A12 aluminum alloy was accelerated due to its poor stability in strong alkali environment,which was attributed to the strong alkalization caused by the corrosion of AZ91D magnesium alloy.With the increase of the potential of 2A12 aluminum alloy as a result of the continuous covering of corrosion products,the potential difference between the two materials was enlarged,which enhanced the galvanic corrosion.

Effect of Cu addition on microstructure and properties of Mg-10Zn-5Al-0.1Sb high zinc magnesium alloy

To improve the strength,hardness and heat resistance of Mg-Zn based alloys,the effects of Cu addition on the as-cast microstructure and mechanical properties of Mg-10Zn-5Al-0.1Sb high zinc magnesium alloy were investigated by means of Brinell hardness measurement,scanning electron microscopy (SEM),energy dispersive spectroscopy (EDS),XRD and tensile tests at room and elevated temperatures.The results show that the microstructure of as-cast Mg-10Zn-5Al-0.1Sb alloy is composed of α-Mg,t-Mg32(Al,Zn)49,φ-Al2Mg5Zn2 and Mg3Sb2 phases.The morphologies of these phases in the Cu-containing alloys change from semi-continuous long strip to black herringbone as well as particle-like shapes with increasing Cu content.When the addition of Cu is over 1.0wt.%,the formation of a new thermally-stable Mg2Cu phase can be observed.The Brinell hardness,room temperature and elevated temperature strengths firstly increase and then decrease as the Cu content increases.Among the Cu-containing alloys,the alloy with the addition of 2.0wt.% Cu exhibits the optimum mechanical properties.Its hardness and strengths at room and elevated temperatures are 79.35 HB,190MPa and 160MPa,which are increased by 9.65%,21.1% and 14.3%,respectively compared with those of the Cu-free one.After T6 heat treatment,the strengths at room and elevated temperatures are improved by 20% and 10%,respectively compared with those of the as-cast alloy.This research results provide a new way for strengthening of magnesium alloys at room and elevated temperatures,and a method of producing thermally-stable Mg-10Zn-5Al based high zinc magnesium alloys.

Electrodeposition of aluminum and aluminum-magnesium alloys at room temperature

Electrodeposition of aluminum from benzene-tetrahydrofuran-Al Cl3-Li Al H4 was studied at room temperature. Galvanostatic electrolysis was used to investigate the effect of various parameters on deposit morphology and crystal size, including current density, temperature, molar ratio of benzene/tetrahydrofuran and stirring speed. The deposit microstructure was adjusted by changing the parameters, and the optimum operating conditions were determined. Dense, bright and adherent aluminum coatings were obtained over a wide range of current densities(10-25 m A/cm2), molar ratio of benzene and tetrahydrofuran(4:1 to 7:8) and stirring speeds(200-500 r/min). Smaller grain sizes and well-adhered deposits were obtained at lower temperatures. Aluminum-magnesium alloys could potentially be used as hydrogen storage materials. A novel method for Al-Mg deposition was proposed by using pure Mg anodes in the organic solvents system benzene-tetrahydrofuran-Al Cl3-Li Al H4. XRD shows that the aluminum-magnesium alloys are mainly Al3Mg2 and Al12Mg17.

Peculiarities of forming diffusion bimetallic joints of aluminum foam with a monolithic magnesium alloy

The work is carried out to determine an optimal method to obtain the welded bimetallic joints of monolithic Mg-alloy with porous Al-alloy using gallium as chemical activator and heating up to 300 ℃ by two different methods:long-term in vacuum oven and short-term without vacuum by passing of low voltage current.There is no microstructure change in Al-foam but indentation test records the negligible reduction of the mechanical properties.SEM showed the crystallization of two types of Mg_(5)Ga_(2) and Mg_(2)Ga inter-metallic phases in the wavy uneven diffusion zone on Mg-alloy side with significant increase of micro-hardness and Young’s modulus.The narrow depth of the diffusion zone takes place in joints by short-term heating,so this method is more applicable for welding of monolithic and porous alloys at chemical activation using gallium.

Effect of Sb on microstructure and mechanical properties in Mg-10Zn-5Al high zinc magnesium alloys

In view of high strength and poor impact toughness of the high-zinc magnesium alloys,the method of micro-alloying was adopted to improve the impact-toughness of Mg-10Zn-5Al high zinc magnesium alloys by adjusting the addition of Sb.The results show that:the dystectic Mg3Sb2 particles formed by Sb and Mg are distributed in the front of dendrite,restrain the growth of the secondary phase and then change the morphology of the secondary phases,which refines the matrix in some extent and improves the impact-toughness of the alloy significantly.But with further increase of Sb addition,Mg3Sb2 particles congregate and form needle-like Mg3Sb2 phase,which dissevers the matrix and leads to the reduction of the strength and impact-toughness of the alloys.Hence,the mechanical prosperities of ZA105 high zinc magnesium alloy are significantly improved with appropriate Sb addition,which provides a new way to extend the application fields of high zinc magnesium alloy.

Ultra-High Mass-Loading Cathode for Aqueous Zinc-Ion Battery Based on Graphene-Wrapped Aluminum Vanadate Nanobelts

Rechargeable aqueous zinc-ion batteries(AZIBs)have their unique advantages of cost efficiency,high safety,and environmental friendliness.However,challenges facing the cathode materials include whether they can remain chemically stable in aqueous electrolyte and provide a robust structure for the storage of Zn2+.Here,we report on H11Al2V6O23.2@graphene(HAVO@G)with exceptionally large layer spacing of(001)plane(13.36?).The graphene-wrapped structure can keep the structure stable during discharge/charge process,thereby promoting the inhibition of the dissolution of elements in the aqueous electrolyte.While used as cathode for AZIBs,HAVO@G electrode delivers ideal rate performance(reversible capacity of 305.4,276.6,230.0,201.7,180.6 mAh g?1 at current densities between 1 and 10 A g?1).Remarkably,the electrode exhibits excellent and stable cycling stability even at a high loading mass of^15.7 mg cm?2,with an ideal reversible capacity of 131.7 mAh g?1 after 400 cycles at 2 A g?1.

Friction self-piercing riveting(F-SPR)of aluminum alloy to magnesium alloy using a flat die

Friction self-piercing riveting(F-SPR)process based on a pip die has been invented to solve the cracking problems in riveting high-strength and low-ductility light metals,such as magnesium alloys,cast aluminum,and 7 series aluminum alloys.In this paper,in order to solve quality issues caused by the misalignment between rivet and pip-die in F-SPR,a flat-die based F-SPR process was proposed and employed to join 1.27 mm-thick AA6061-T6 to 3 mm-thick AZ31B.The results indicate that a 1.0 mm die distance is effective to avoid rivet upset and insufficient flaring.As the feed rate increases,the heat input in the whole process decreases,resulting in a larger riveting force,which in turn increases both the bottom thickness and interlock amount.Besides,solid-state bonding,including Al-Mg intermetallic compounds(IMCs),Al-Mg mechanical mixture,and Al-Fe atom interdiffusion was observed at the joint interfaces.The upper Al layer was softened,but the lower Mg layer was hardened,and both sheets exhibited a narrowed affected region with the increase of feed rate,while the rivet hardness shows no obvious change.Three fracture modes appeared accompanying the variations in lap-shear strength and energy absorption as the feed rate increased from 2 mm/s to 8 mm/s.Finally,the F-SPR process using a flat die was compared to those using a pip die and a flat bottom die to show the advantage of flat die on coping with the misalignment problem.

EIS Study on Pitting Corrosion of AA5083-H321 Aluminum-Magnesium Alloy in Stagnant 3.5% NaCl Solution

In this research, EIS （electrochemical impedance spectroscopy） technique was utilized to study the pitting corrosion behaviour of AA5083-H321 aluminum-magnesium alloy in 3.5% NaCl solution. Impedance spectra were obtained during 240 h of exposure of the sample to the test solution. The surface and cross-section of the samples were studied by scanning electron microscopy （SEM） and EDAX （energy dispersive analysis of X-ray） analysis. The results indicated that as the resistance of the passive layer on intermetallic particles is very small, this parameter on the sample surface layers is controlled by that of pure passive layer. However, the capacitors in the proposed equivalent circuit are replaced with the constant phase elements （CPE）, due to non-uniformity and occurrence of pitting corrosion on the surface. The outward diffusion of Al^＋3 ions through the passive layer and the thickening of this layer cause the impedance decrease in the first 24 h and increase afterwards. The detachment of intermetallic particles from some of pits and the accumulation of the corrosion products inside some others are factors that prevents the continuation of cathodic reactions on the top of the intermetallic particles.

Role of Chloride Ion and Dissolved Oxygen in Electrochemical Corrosion of AA5083-H321 Aluminum-Magnesium Alloy in NaCl Solutions under Flow Conditions

Flow-induced corrosion consists electrochemical and mechanical components. The present paper has to assessed the role of chloride ion and dissolved oxygen in the electrochemical component of flow induced corrosion for AA5083-H321 aluminum-magnesium alloy which is extensively used in the construction of high-speed boats, submarines, hovercrafts, and desalination systems, in NaCI solutions. Electrochemical tests were carried out at flow velocities of 0, ：2, 5, 7 and 10 m/s, in aerated and deaerated NaCI solutions with different sodium chloride concentrations. The results showed that the high rate of oxygen reduction under hydrodynamic conditions causes an increase in the density of pits on the surface. The increase of chloride ions concentration under flow conditions accelerates the rate of anodic reactions, but have no influence on the cathodic reactions. Thus, in the current work, it was found that under flow conditions, due to the elimination of corrosion products inside the pits, corrosion resistance of the alloy is increased.

Phase selection of ternary intermetallic compounds during solidification of high zinc magnesium alloy

The phase selection of ternary intermetallic compound τphase (Mg32(Al, Zn)49 ) and φ phase (Al2Mg5Zn2) in high zinc magnesium alloys was studied by using scanning electron microscope, X-ray diffractometer and differential scanning calorimeter, etc. The results indicate that, when adding element Si in Mg-8Zn-4Al-0.3Mn (ZA84) alloy, φ phase is promoted, whereas τ phase is inhibited. The Chinese script-type Mg2Si and matrix microstructure are greatly refined, the formation of τ phase is facilitated and φ phase is restrained when modifier Al-AlP master alloy is added in ZA84 alloy containing Si. The kinetics study of phase selection indicates that there is a critical degree of undercooling of the melt. If the undercooling exceeds the critical value, τ phase preferentially forms while φ phase is restrained; otherwise, φ phase preferentially forms while τ phase is restrained.

Aluminum-zinc alloy squeeze casting technological parameters optimization based on PSO and ANN

This paper presents a kind of ZA27 squeeze casting process parameter optimization method using artificial neural network (ANN) combined with the particle swarm optimizer (PSO). Regarding the test data as samples and using neural network create ZA27 squeeze casting process parameters and mechanical properties of nonlinear mapping model. Using PSO optimize the model and obtain the optimum value of the process parameters. Make full use of the non-neural network mapping capabilities and PSO global optimization capability. The network uses the radial direction primary function neural network,using the clustering and gradient method to make use of network learning,in order to enhance the generalization ability of the network. PSO takes dynamic changing inertia weights to accelerate the convergence speed and avoid a local minimum.

Corrosion behavior of sintered zinc-aluminum coating in NaCl solution

Sintered zinc aluminum coating (SZAC) was prepared using zinc flakes, aluminum flakes and CrO 3 as main raw materials. The corrosion behavior of SZAC in 3.5%NaCl solution was studied by means of SEM, EDS, EIS and so on. Results indicate that aluminum corroded in advance of zinc to produce speculate or spherical substances, which attaches to SZAC and adds mass to it. Corrosion production passivates metal powders in SZAC, causes E corr of SZAC to increase gradually, and causes the arising of the third time constant in EIS, which corresponds to the insulation of corrosion production.