The high consumption of electricity and issues related to fossil energy have triggered an increase in energy prices and the scarcity of fossil resources.Consequently,many researchers are seeking alternative energy sou...The high consumption of electricity and issues related to fossil energy have triggered an increase in energy prices and the scarcity of fossil resources.Consequently,many researchers are seeking alternative energy sources.One potential technology,the Microbial Fuel Cell(MFC)based on rice,vegetable,and fruit wastes,can convert chemical energy into electrical energy.This study aims to determine the potency of rice,vegetable,and fruit waste assisted by Cu/Mg electrodes as a generator of electricity.The method used was a laboratory experiment,including the following steps:electrode preparation,waste sample preparation,incubation of the waste samples,construction of a reactor using rice,vegetable,and fruit waste as a source of electricity,and testing.The tests included measuring electrical conductivity,electric current,voltage,current density,and power density.Based on the test results,the maximum current and voltage values for the fruit waste samples were 5.53 V and 11.5 mA,respectively,with a current density of 2.300 mA/cm^(2) and a power density of 12.719 mW/cm^(2).The results indicate the potential for a future development.The next step in development involves determining the optimum conditions for utilizing of rice,vegetable,and fruit waste.The results of the electrical conductivity test on rice,vegetable,and fruit waste samples were 1.51,2.88,and 3.98 mS,respectively,with the highest electrical conductivity value found in the fruit waste sample.展开更多
The presence of waste tires poses an environmental challenge as they occupy a significant amount of land and are expensive to dispose in landfills.However,reusing waste tires can address this issue when waste tires ar...The presence of waste tires poses an environmental challenge as they occupy a significant amount of land and are expensive to dispose in landfills.However,reusing waste tires can address this issue when waste tires are used in geotechnical applications.To determine the viability of this approach,laboratoryscale tests were conducted to investigate load-bearing capacity of circular footings on sand-tire shred(STS)mixtures with shredded waste tire contents of 5%e15%by weight and three different widths of shreds.The investigation focused on analyzing the thickness of layers composed of STS mixtures,the soil cap,and the impact of geogrids on bearing capacity.The results indicate that a specific mixture of sand and tire shreds provides the highest footing-bearing capacity.In addition,the optimal shred content and size were found to be 10%by weight and 2 cm×10 cm,respectively.Furthermore,for a given tire shred width,a particular length provides the largest bearing capacity.The results agree well with that of previous research conducted by the first author and his colleagues in direct shear and California bearing ratio(CBR)tests.The primary finding of this research is that the use of two-layered STS mixtures reinforced by geogrids significantly enhances the bearing capacity.展开更多
To achieve the resource utilization of solid waste phosphogypsum(PG)and tackle the problem of utilizing potassium feldspar(PF),a coupled synergistic process between PG and PF is proposed in this paper.The study invest...To achieve the resource utilization of solid waste phosphogypsum(PG)and tackle the problem of utilizing potassium feldspar(PF),a coupled synergistic process between PG and PF is proposed in this paper.The study investigates the features of P and F in PG,and explores the decomposition of PF using hydrofluoric acid(HF)in the sulfuric acid system for K leaching and leaching of P and F in PG.The impact factors such as sulfuric acid concentration,reaction temperature,reaction time,material ratio(PG/PF),liquid–solid ratio,PF particle size,and PF calcination temperature on the leaching of P and K is systematically investigated in this paper.The results show that under optimal conditions,the leaching rate of K and P reach more than 93%and 96%,respectively.Kinetics study using shrinking core model(SCM)indicates two significant stages with internal diffusion predominantly controlling the leaching of K.The apparent activation energies of these two stages are 11.92 kJ·mol^(-1)and 11.55 kJ·mol^(-1),respectively.展开更多
This study investigates the use of waste fat biodiesel(WFB)from the leather industry as a substitute for diesel fuel.Specifically,it examines the diesel engine performance of WFB,a blend of WFB and diesel(B50),and dif...This study investigates the use of waste fat biodiesel(WFB)from the leather industry as a substitute for diesel fuel.Specifically,it examines the diesel engine performance of WFB,a blend of WFB and diesel(B50),and different blends of WFB and silicon dioxide(SiO_(2))nanoparticles(B50SiO_(2)40,B50SiO_(2)80,and B50SiO_(2)120μg/g).The results indicate that the B50SiO_(2)120 blend increases brake thermal efficiency by 10.03%compared to pure biodiesel but falls 1.93%short of neat diesel.Furthermore,the B50SiO_(2)120 mixture reduces smoke,hydrocarbon,and carbon monoxide emissions by 31.87%,34.14%,and 43.97%respectively,compared to diesel.However,the B50SiO_(2)120 blend shows a 4.91%increase in nitrogen oxide emissions compared to diesel.展开更多
During the highway construction,a large number of spoil areas will be generated while a large amount of waste slag and soil could not be rationally utilized.Besides,the vegetation recovery is slow in the spoil areas d...During the highway construction,a large number of spoil areas will be generated while a large amount of waste slag and soil could not be rationally utilized.Besides,the vegetation recovery is slow in the spoil areas due to the soil depletion.Aiming at recycling the solid waste,the sieved engineering waste slag with local red clay and corn straw biochar was supplied to solve the problem of insufficient nutrients in engineering waste slag and soil.In addition,planting experiments of alfalfa(Medicago sativa L.)and Amorpha fruticosa L.combined with physical and chemical experiments were carried out to prove the feasibility of the novel improved substrate for the reclamation of spoil areas.The results show that the substrate's improvement effect is mainly affected by the soil to slag ratio and the biochar content.The improvement effect of soil matrix in highway spoil area decreases with the increase of the waste slag content,especially when the soil-slag ratio is less than 3,and the promotion of plants is limited.On the contrary,the improvement effect is proportional to the biochar content(3%-8%).But it is noted that the Cu and Pb in the soil will exceed the clean limit corresponding to the Nemero soil pollution index level when the biochar content is 8%.Therefore,it is recommended that the soil-slag ratio should be≥3,and the biochar content should reach 3%-5%.This research provides experimental basis and technical support for utilizing solid waste resources in the reclamation of highway spoil areas.展开更多
MXene,a transition metal carbide/nitride,has been prominent as an ideal electrochemical active material for supercapacitors.However,the low MXene load limits its practical applications.As environmental concerns and su...MXene,a transition metal carbide/nitride,has been prominent as an ideal electrochemical active material for supercapacitors.However,the low MXene load limits its practical applications.As environmental concerns and sustainable development become more widely recognized,it is necessary to explore a greener and cleaner technology to recycle textile by-products such as cotton.The present study proposes an effective 3D fabrication method that uses MXene to fabricate waste denim felt into ultralight and flexible supercapacitors through needling and carbonization.The 3D structure provided more sites for loading MXene onto Z-directional fiber bundles,resulting in more efficient ion exchange between the electrolyte and electrodes.Furthermore,the carbonization process removed the specific adverse groups in MXenes,further improving the specific capacitance,energy density,power density and electrical conductivity of supercapacitors.The electrodes achieve a maximum specific capacitance of 1748.5 mF cm-2 and demonstrate remarkable cycling stability maintaining more than 94%after 15,000 galvanostatic charge/discharge cycles.Besides,the obtained supercapacitors present a maximum specific capacitance of 577.5 mF cm^(-2),energy density of 80.2μWh cm^(-2)and power density of 3 mW cm^(-2),respectively.The resulting supercapacitors can be used to develop smart wearable power devices such as smartwatches,laying the foundation for a novel strategy of utilizing waste cotton in a high-quality manner.展开更多
As socioeconomic development continues,the issue of building energy consumption has attracted significant attention,and improving the thermal insulation performance of buildings has become a crucial strategic measure....As socioeconomic development continues,the issue of building energy consumption has attracted significant attention,and improving the thermal insulation performance of buildings has become a crucial strategic measure.Simultaneously,the application of solid waste in insulation materials has also become a hot topic.This paper reviews the sources and classifications of solid waste,focusing on research progress in its application as insulation materials in the domains of daily life,agriculture,and industry.The research shows that incorporating household solid waste materials,such as waste glass,paper,and clothing scraps into cementitious thermal insulation can significantly reduce the thermal conductivity of the materials,leading to excellent thermal insulation properties.Insulation materials prepared from agricultural solid waste,such as barley straw,corn stalk,chicken feather,and date palm fibers,possess characteristics of lightweight and strong thermal insulation.Industrial solid waste,including waste tires,iron tailings,and coal bottom ash,can also be utilized in the preparation of insulation materials.These innovative applications not only have positive environmental significance by reducing waste emissions and resource consumption,but also provide efficient and sustainable insulation solutions for the construction industry.However,to further optimize the mix design and enhance the durability of insulation materials,continuous research is required to investigate the mechanisms through which solid waste impacts the performance of insulation materials.展开更多
Health-care waste contains potentially harmful microorganisms and compounds which can infect and affect hospital patients, healthcare workers, the general public and environment. Therefore, management of health care w...Health-care waste contains potentially harmful microorganisms and compounds which can infect and affect hospital patients, healthcare workers, the general public and environment. Therefore, management of health care waste requires safe handling, treatment and disposal procedures. While incineration reduces the volume and quantity of waste for final disposal, it leads to the production of fly and bottom ashes laden with toxic incomplete combustion products such as Polycyclic Aromatic Hydrocarbons (PAHs), dioxins, furans and heavy metals. This exposes workers who handle and dispose the bottom ashes, hospital patients, the general public and environment. The goal of this study was to determine the total and individual levels of 16 most prevalent and toxic PAHs. Bottom ash samples were collected from incinerators in five county hospitals in Kenya, namely;Moi-Voi, Narok, Kitale, Makindu and Isiolo. Bottom ash samples were collected over a period of six months from the five hospitals. The samples were then sieved, homogenised and stored at 4°C in amber coloured glass containers. The PAHs were extracted using 30 ml of a hexane-acetone solvent (1:1) mixture by ultrasonication at room temperature (23°C) for 45 minutes. The PAHs were then analyzed with a GC-MS spectrophotometer model (Shimadzu GCMS-QP2010 SE) connected to a computer work station was used for the PAHs analysis. The GC-MS was equipped with an SGE BPX5 GC capillary column (30 m × 0.25 mm × 0.25 μm) for the separation of compounds. Helium was used as the carrier gas at a flow rate of 15.5 ml/minute and 14.5 psi. 1 μl of the sample was injected at 280°C, split mode (10:1). The oven programming was set for a total runtime of 40 minutes, which included: 100°C (2-minute hold);10°C /min rise to 200°C;7°C /min rise to 249°C;3°C /min rise to 300°C (2-minute hold). The interface temperature was set at 290°C. Analysis was done in Selected Ion Monitoring (SIM) mode and the peak areas of each of the PAHs were collected from the chromatograph and used for quantification of the 16 PAHs listed by the U.S. Environmental Protection Agency (EPA) which included, BaA (benz[a]anthracene: 4 rings), BaP (benzo[a]pyrene: 5 rings), BbF (benzo [b]fluoranthene: 5 rings), BkF (benzo[k]fluoranthene: 5 rings), Chr (chrysene: 4 rings), DbA (dibenz[a,h]anthracene: 5 rings), InP (indeno[1,2,3 - cd] pyrene: 6 rings) and Acp (acenaphthene: 3 rings), Acpy (acenaphthylene: 3 rings), Ant (anthracene: 3 rings), BghiP (benzo[g,h,i]perylene: 6 rings), Flu (fluorene: 3 rings), FluA (fluoranthene: 4 rings), Nap (naphthalene: 2 rings), PhA (phenanthrene: 3 rings) and Pyr (pyrene: 4 rings). Ion source-interface temperature was set at 200°C - 250°C. Internal standards from Sigma Aldrich were used in the analysis and the acquired mass spectra data were then matched against the NIST 2014 library [1] [2]. The mean PAHs concentration in the bottom ashes of each hospital varied broadly from 0.001 mg/kg to 0.4845 mg/kg, and the mean total concentration levels of individual PAHs ranged from 0.0072 mg/kg to 1.171 mg/kg. Low molecular weight PAHs (Phenanthrene, Naphthalene and Fluorene) were predominant in all the hospital wastes whereas Kitale and Narok presented the lowest PAHs concentrations and the lowest number of individual PAHs. Moi/Voi recorded the highest total PAHs concentration at 1.3129 ± 0.0023 mg/kg from a total of 11 PAHs being detected from the bottom ash samples. Narok had only three PAHs being detected at very low concentrations of 0.0041 ± 0.00 mg/kg, 0.0076 ± 0.00 mg/kg and 0.012 ± 0.00 mg/kg for phenanthrene, anthracene and chrysene respectively. This study presents hospital incinerator bottom ash as containing detectable levels of both carcinogenic and non-carcinogenic PAHs. Continued unprotected exposure of hospital workers (waste handlers) to the bottom ash PAHs could be hazardous to their health because of their cumulative effect. Preventive measures e.g. the use of Personal protective equipment (PPE) should be prioritised to minimise direct contact with the bottom ash. The study recommends an upgrade on incinerator technology for efficient combustion processes thus for better pollution control.展开更多
This study aims to investigate the feasibility of using decoration waste powder(DWP)as a partial replacement for fly ash(FA)in the preparation of geopolymer masonry mortar,and to examine the effect of different DWP re...This study aims to investigate the feasibility of using decoration waste powder(DWP)as a partial replacement for fly ash(FA)in the preparation of geopolymer masonry mortar,and to examine the effect of different DWP replacement rates(0%-40%)on the fresh and mechanical properties of the mortar.The results showed that each group of geopolymer masonry mortar exhibited excellent water retention performance,with a water retention rate of 100%,which was due to the unique geopolymer mortar system and high viscosity of the alkaline activator solution.Compared to the control group,the flowability of the mortar containing lower contents of DWP(10%and 20%)was higher.However,as the DWP replacement rate further increased,the flowability gradually decreased.The DWP could absorb the free water in the reaction system of geopolymer mortar,thereby limiting the occurrence of geopolymerization reaction.The incorporation of DWP in the mortar resulted in a decrease in compressive strength compared to the mortar without DWP.However,even at a replacement rate of 40%,the compressive strength of the mortar still exceeded 15 MPa,which met the requirements of the masonry mortar.It was feasible to use DWP in the geopolymer masonry mortar.Although the addition of DWP caused some performance loss,it did not affect its usability.展开更多
Freetown which is the capital city of Sierra Leone is facing challenges with population growth, urbanization, and industrialization, leading to an increase in municipal solid waste (MSW) generation. The study aims to ...Freetown which is the capital city of Sierra Leone is facing challenges with population growth, urbanization, and industrialization, leading to an increase in municipal solid waste (MSW) generation. The study aims to evaluate MSW generation, composition, and disposal methods, as well as the impact of collection fees, policy implementation, and women’s participation in municipal solid waste management (MSWM). The study used both qualitative and quantitative methods for data collection and analysis. The study administered 393 structured questionnaires in three selected sections to collect data on variables such as family size, education, level of knowledge, etc. The study used door-to-door data collection to determine the rate of solid waste generation, composition, and disposal in 66 households from two of the selected sections and 34 households from the other section to evaluate the current situation of MSWM practices among households in Freetown. The study used a descriptive statistic to analyze the data collected using Origin-Pro9 and MS Excel software. The findings showed that with a 4.2% urban growth rate, Freetown had a population of 1,467,543 in 2023, generating 851 tons of MSW per day, with organic waste accounting for 78% of the total MSW generated. Plastic waste generation also increased from 7.6% in 2020 to 13% in 2023. The study emphasizes the need to sustain the MSWM system by prioritizing solid waste collection fees, policy enforcement, and women’s participation in the MSWM sector. It further suggests and provides recommendations for developing an efficient and sustainable MSWM system in Sierra Leone, including knowledge transfer from countries like China and the US.展开更多
This investigation is focused on conducting a thorough analysis of Municipal Solid Waste Management (MSWM). MSWM encompasses a range of interdisciplinary measures that govern the various stages involved in managing un...This investigation is focused on conducting a thorough analysis of Municipal Solid Waste Management (MSWM). MSWM encompasses a range of interdisciplinary measures that govern the various stages involved in managing unwanted or non-utilizable solid materials, commonly known as rubbish, trash, junk, refuse, and garbage. These stages include generation, storage, collection, recycling, transportation, handling, disposal, and monitoring. The waste materials mentioned in this context exhibit a wide range of items, such as organic waste from food and vegetables, paper, plastic, polyethylene, iron, tin cans, deceased animals, byproducts from demolition activities, manure, and various other discarded materials. This study aims to provide insights into the possibilities of enhancing solid waste management in the Farmgate area of Dhaka North City Corporation (DNCC). To accomplish this objective, the research examines the conventional waste management methods employed in this area. It conducts extensive field surveys, collecting valuable data through interviews with local residents and key individuals involved in waste management, such as waste collectors, dealers, intermediate dealers, recyclers, and shopkeepers. The results indicate that significant amounts of distinct waste categories are produced daily. These include food and vegetable waste, which amount to 52.1 tons/day;polythene and plastic, which total 4.5 tons/day;metal and tin-can waste, which amounts to 1.4 tons/day;and paper waste, which totals 5.9 tons/day. This study highlights the significance of promoting environmental consciousness to effectively shape the attitudes of urban residents toward waste disposal and management. It emphasizes the need for collaboration between authorities and researchers to improve the current waste management system.展开更多
Due to the acceleration of urbanization,the municipal waste(MW)problem has transformed into a global challenge for urb-an sustainability.To elucidate historical trends,current focal points,and future directions in MW ...Due to the acceleration of urbanization,the municipal waste(MW)problem has transformed into a global challenge for urb-an sustainability.To elucidate historical trends,current focal points,and future directions in MW research,we conducted a bibliometric analysis and employed knowledge graph visualization to scrutinize a total of 34212 articles,which were published between 1991 and 2021 in the Web of Science(WoS)core database.The results indicated that current major research themes encompass waste classifica-tion and recycling,waste management and public behavior,waste disposal methods and technologies,as well as environmental impact and evaluation.There has been a shift in the research focus from the environmental impacts of waste incineration to sustainable manage-ment related issues.A comparison of research from six typical countries revealed the differences in research priorities and techniques advantages.Scholars from the USA and Britain initiated MW research earlier than other countries and investigated management issues in depth,such as public behavior and willingness to pay.Meanwhile,Japanese,German,and Swedish scholars conducted extensive studies on advanced waste treatment technologies,such as disposal and recycling,risk assessment,and waste-to-energy techniques.Chinese scholars placed particular emphasis on end-of-pipe treatments and their associated environmental impacts.Hotspots and poten-tial future frontiers were identified by burst detection analysis.Keywords with high value of burst index(BI)worldwide are food waste and circular economy.Chinese scholars have put great efforts on waste environmental impact and its recycling technologies,while we’re expecting to further investigating vulnerable population.Furthermore,this study contributes to bridging the regional gap of scientific research among different countries and fostering international collaboration.展开更多
Despite the fact that a few countries in the Mediterranean and the Middle East have limited crude oil reserves, they have abundant biomass feedstocks. For instance, Jordan relies heavily on the importation of natural ...Despite the fact that a few countries in the Mediterranean and the Middle East have limited crude oil reserves, they have abundant biomass feedstocks. For instance, Jordan relies heavily on the importation of natural gas and crude oil for its energy needs;but, by applying thermochemical conversion techniques, leftover olive oil can be used to replace these energy sources. Understanding the chemical, physical, and thermal characteristics of raw materials is essential to obtaining the most out of these conversion processes. Thermogravimetric analysis was used in this study to examine the thermal behavior of olive-solid residue (kernel) at three different heating rates (5, 20 and 40 C/min) in nitrogen and oxygen atmospheres. The initial degradation temperature, the residual weight at 500 and 700˚C and the thermal degradation rate during the devolatilization stage (below 400˚C) were all determined. It was found that in N<sub>2</sub> and O<sub>2</sub> atmospheres, both the initial degradation temperature and the degradation rate increase with increasing heating rates. As heating rates increase in the N<sub>2</sub> atmosphere, the residual weight at 500 or 700˚C decreases slightly, but at low heating rates compared to high heating rates in the O<sub>2</sub> atmosphere, it decreases significantly. This suggests that a longer lignin oxidation process is better than a shorter one. Coats and Redfern approach was used to identify the mechanism and activation energy for the devolatilization stage of pyrolysis and oxidation reactions. The process mechanism analysis revealed that the model of first-order and second-order reactions may adequately describe the mechanism of heat degradation of the devolatilization step of olive-solid waste for pyrolysis and oxidation processes, respectively.展开更多
The production and consumption of avocado pears generates tons of wastes, mainly the pear peels which are usually discarded, although they have been reported to contain important phyto-chemicals with biological activi...The production and consumption of avocado pears generates tons of wastes, mainly the pear peels which are usually discarded, although they have been reported to contain important phyto-chemicals with biological activities. The adverse health effect associated with the consumption of saturated lipid based foods has ignited research on reformulation of lipid based foods to eliminate Trans Fatty Acids (TFAs). This study was thus aimed at the extraction and characterization of oil from Avocado Peels (APO) and evaluation of the quality of margarine produced from it. Five verities of pear were used for oil extraction by soxhlet method and physiochemical, oxidative, functional and antioxidant characterization was done. Margarines were formulated using a central composite design using oil blends of APO and Virgin Coconut Oil (VCO) with an oil ratio of 10:90, 40:60, 70:30 respectively, varied blending speed, blending time, and chitosan concentration. Samples were characterized and the effect of process parameters on the physiochemical and functional properties of the margarine studied. Optimized conditions were used to produce samples for sensory evaluation. Color, spreadability, aroma, taste and general acceptability was evaluated using ranking difference test. The results showed that the yield, density, and iodine values of APOs oils ranged from 14.91 ± 0.18 to 11.76 ± 0.46;0.93 ± 0.001 to 0.99 ± 0.1;46.63 ± 1.70 to 52.4 ± 0.63, their acid values, TBA and PV values ranged from 1.42 ± 0.39 to 1.97 ± 0.5;0.11 ± 0.002 to 0.18 ± 0.04;and 2.72 ± 0.14 to 4.43 ± 0.36 respectively, with Brogdon avocado peel variety having the overall best properties prepared blends of trans-free APO margarines showed that increase in APO ratio decreased melting point, increased oxidative stability and reduced moisture content of margarine samples. Chitosan addition leads to decrease moisture content and increase functional properties. VCO lead to increase in phenolic and flavonoid content of the margarines. Samples were spreadable and palatable with R20 being most palatable and the most accepted being R26 with a mean score of 7.07 ± 0.70. Decrease in color intensity increased acceptability. This study therefore demonstrated that avocado peel waste biomass can be valorized by using it as raw material for oil extraction, which can serve as good material for the production of trans-free margarines with good oxidative stability, functional and antioxidant properties.展开更多
The mining process involves drilling and excavation, resulting in the production of waste rock and tailings. The waste materials are then removed and stored in designated areas. This study aims to evaluate the mechani...The mining process involves drilling and excavation, resulting in the production of waste rock and tailings. The waste materials are then removed and stored in designated areas. This study aims to evaluate the mechanical strength and the environmental and economic impact of using Coltan Mining Waste (CMW) as a substitute for aggregates in concrete and mortar production. To achieve this, the CMW needs to be characterised. The Dreux Gorisse method was primarily used to produce concrete with a strength of 20 MPa at 28 days. The mortars, on the other hand, were formulated according to the NF P 18-452 standard. The environmental impact of using CMW as substitutes for natural aggregates in the production of concrete and mortar was analysed using SimaPro software. The results showed that mortars and concrete made with CMW have comparable compressive strengths to the reference mortar and concrete;reduce the negative impact on ecosystem quality, human health, resources, and climate change. It has also been shown that the substitution of aggregates by CMW reduces the cost of concrete and mortar as a function of the distance from the aggregate footprint.展开更多
With the application of resins in various fields, numerous waste resins that are difficult to treat have been produced. The industrial wastewater containing Cr(Ⅵ) has severely polluted soil and groundwater environmen...With the application of resins in various fields, numerous waste resins that are difficult to treat have been produced. The industrial wastewater containing Cr(Ⅵ) has severely polluted soil and groundwater environments, thereby endangering human health. Therefore, in this paper, a novel functionalized mesoporous adsorbent PPR-Z was synthesized from waste amidoxime resin for adsorbing Cr(Ⅵ). The waste amidoxime resin was first modified with H3PO4 and ZnCl_(2), and subsequently, it was carbonized through slow thermal decomposition. The static adsorption of PPR-Z conforms to the pseudo-second-order kinetic model and Langmuir isotherm, indicating that the Cr(Ⅵ) adsorption by PPR-Z is mostly chemical adsorption and exhibits single-layer adsorption. The saturated adsorption capacity of the adsorbent for Cr(Ⅵ) could reach 255.86 mg/g. The adsorbent could effectively reduce Cr(Ⅵ) to Cr(Ⅲ) and decrease the toxicity of Cr(Ⅵ) during adsorption. PPR-Z exhibited Cr(Ⅵ) selectivity in electroplating wastewater. The main mechanisms involved in the Cr(Ⅵ) adsorption are the chemical reduction of Cr(Ⅵ) into Cr(Ⅲ) and electrostatic and coordination interactions. Preparation of PPR-Z not only solves the problem of waste resin treatment but also effectively controls Cr(Ⅵ) pollution and realizes the concept of “treating waste with waste”.展开更多
Waste production rises in tandem with population growth and increased utilization.The indecorous disposal of waste paves the way for huge disaster named as climate change.The National Environment Agency(NEA)of Singapo...Waste production rises in tandem with population growth and increased utilization.The indecorous disposal of waste paves the way for huge disaster named as climate change.The National Environment Agency(NEA)of Singapore oversees the sustainable management of waste across the country.The three main contributors to the solid waste of Singapore are paper and cardboard(P&C),plastic,and food scraps.Besides,they have a negligible rate of recycling.In this study,Machine Learning techniques were utilized to forecast the amount of garbage also known as waste audits.The waste audit would aid the authorities to plan their waste infrastructure.The applied models were k-nearest neighbors,Support Vector Regressor,ExtraTrees,CatBoost,and XGBoost.The XGBoost model with its default parameters performed better with a lower Mean Absolute Percentage Error(MAPE)of 8.3093(P&C waste),8.3217(plastic waste),and 6.9495(food waste).However,Grid Search Optimization(GSO)was used to enhance the parameters of the XGBoost model,increasing its effectiveness.Therefore,the optimized XGBoost algorithm performs the best for P&C,plastics,and food waste with MAPE of 4.9349,6.7967,and 5.9626,respectively.The proposed GSO-XGBoost model yields better results than the other employed models in predicting municipal solid waste.展开更多
Zinc metal is a promising anode material for next-generation aqueous batteries,but its practical application is limited by the formation of zinc dendrite.To prevent zinc dendrite growth,various Zn^(2+)-conducting but ...Zinc metal is a promising anode material for next-generation aqueous batteries,but its practical application is limited by the formation of zinc dendrite.To prevent zinc dendrite growth,various Zn^(2+)-conducting but water-isolating solid-electrolyte interphase(SEI)films have been developed,however,the required high-purity chemical materials are extremely expensive.In this work,phosphogypsum(PG),an industrial byproduct produced from the phosphoric acid industry,is employed as a multifunctional protective layer to navigate uniform zinc deposition.Theoretical and experimental results demonstrate that PG-derived CaSO_(4)2H_(2)O can act as an artificial SEI layer to provide fast channels for Zn^(2+)transport.Moreover,CaSO_(4)2H_(2)O could release calcium ions(Ca^(2+))due to its relatively high Kspvalue,which have a higher binding energy than that of Zn^(2+)on the Zn surface,thus preferentially adsorbing to the tips of the protuberances to force zinc ions to nucleate at inert region.As a result,the Zn@PG anode achieves a high Coulombic efficiency of 99.5%during 500 cycles and long-time stability over 1000 hours at 1 m A cm^(-2).Our findings will not only construct a low-cost artificial SEI film for practical metal batteries,but also achieve a high-value utilization of phosphogypsum waste.展开更多
Globally,the efficient utilization of polymer wastes is one of the most important issues for current sustainable development topics.Herein,a green and efficient low-temperature combustion approach is proposed to deal ...Globally,the efficient utilization of polymer wastes is one of the most important issues for current sustainable development topics.Herein,a green and efficient low-temperature combustion approach is proposed to deal with polymer wastes and recover heat energy,simultaneously alleviating the environment and energy crisis.Non-noble metal oxides(Al_(2)O_(3),Fe_(2)O_(3),NiO_(2),ZrO_(2),La_(2)O_(3)and CeO_(2)) were prepared,characterized and screened to boost the low-temperature combustion of polyethylene waste at 300℃ in air.The mass change,heat release and CO_(x) formation were studied in details and employed to evaluate the combustion rate and efficiency.It was found that CeO_(2)significantly enhanced the combustion rate and efficiency,which was respectively 2 and 7 times that of non-catalytic case.An interesting phenomenon was observed that the catalytic performance of CeO_(2) in polyethylene low-temperature combustion was significantly improved by the 7-day storage in the room environment or water treatment.XPS analysis confirmed the co-existence of Ce^(3+) and Ce^(4+) in CeO_(2),and the 7-day storage and water treatment promoted the amount of Ce^(3+),which facilitated the formation of the oxygen vacancies.That may be the reason why CeO_(2) exhibited excellent catalytic performance in polyethylene low-temperature combustion.展开更多
With the continuous development of the economy and society,plastic pollution in rivers,lakes,oceans,and other bodies of water is increasingly severe,posing a serious challenge to underwater ecosystems.Effective cleani...With the continuous development of the economy and society,plastic pollution in rivers,lakes,oceans,and other bodies of water is increasingly severe,posing a serious challenge to underwater ecosystems.Effective cleaning up of underwater litter by robots relies on accurately identifying and locating the plastic waste.However,it often causes significant challenges such as noise interference,low contrast,and blurred textures in underwater optical images.A weighted fusion-based algorithm for enhancing the quality of underwater images is proposed,which combines weighted logarithmic transformations,adaptive gamma correction,improved multi-scale Retinex(MSR)algorithm,and the contrast limited adaptive histogram equalization(CLAHE)algorithm.The proposed algorithm improves brightness,contrast,and color recovery and enhances detail features resulting in better overall image quality.A network framework is proposed in this article based on the YOLOv5 model.MobileViT is used as the backbone of the network framework,detection layer is added to improve the detection capability for small targets,self-attention and mixed-attention modules are introduced to enhance the recognition capability of important features.The cross stage partial(CSP)structure is employed in the spatial pyramid pooling(SPP)section to enrich feature information,and the complete intersection over union(CIOU)loss is replaced with the focal efficient intersection over union(EIOU)loss to accelerate convergence while improving regression accuracy.Experimental results proved that the target recognition algorithm achieved a recognition accuracy of 0.913 and ensured a recognition speed of 45.56 fps/s.Subsequently,Using red,green,blue and depth(RGB-D)camera to construct a system for identifying and locating underwater plastic waste.Experiments were conducted underwater for recognition,localization,and error analysis.The experimental results demonstrate the effectiveness of the proposed method for identifying and locating underwater plastic waste,and it has good localization accuracy.展开更多
文摘The high consumption of electricity and issues related to fossil energy have triggered an increase in energy prices and the scarcity of fossil resources.Consequently,many researchers are seeking alternative energy sources.One potential technology,the Microbial Fuel Cell(MFC)based on rice,vegetable,and fruit wastes,can convert chemical energy into electrical energy.This study aims to determine the potency of rice,vegetable,and fruit waste assisted by Cu/Mg electrodes as a generator of electricity.The method used was a laboratory experiment,including the following steps:electrode preparation,waste sample preparation,incubation of the waste samples,construction of a reactor using rice,vegetable,and fruit waste as a source of electricity,and testing.The tests included measuring electrical conductivity,electric current,voltage,current density,and power density.Based on the test results,the maximum current and voltage values for the fruit waste samples were 5.53 V and 11.5 mA,respectively,with a current density of 2.300 mA/cm^(2) and a power density of 12.719 mW/cm^(2).The results indicate the potential for a future development.The next step in development involves determining the optimum conditions for utilizing of rice,vegetable,and fruit waste.The results of the electrical conductivity test on rice,vegetable,and fruit waste samples were 1.51,2.88,and 3.98 mS,respectively,with the highest electrical conductivity value found in the fruit waste sample.
文摘The presence of waste tires poses an environmental challenge as they occupy a significant amount of land and are expensive to dispose in landfills.However,reusing waste tires can address this issue when waste tires are used in geotechnical applications.To determine the viability of this approach,laboratoryscale tests were conducted to investigate load-bearing capacity of circular footings on sand-tire shred(STS)mixtures with shredded waste tire contents of 5%e15%by weight and three different widths of shreds.The investigation focused on analyzing the thickness of layers composed of STS mixtures,the soil cap,and the impact of geogrids on bearing capacity.The results indicate that a specific mixture of sand and tire shreds provides the highest footing-bearing capacity.In addition,the optimal shred content and size were found to be 10%by weight and 2 cm×10 cm,respectively.Furthermore,for a given tire shred width,a particular length provides the largest bearing capacity.The results agree well with that of previous research conducted by the first author and his colleagues in direct shear and California bearing ratio(CBR)tests.The primary finding of this research is that the use of two-layered STS mixtures reinforced by geogrids significantly enhances the bearing capacity.
基金jointly supported by the National Key Research and Development Program of China (2019YFC1905800)the National Key Research & Development Program of China (2018YFC1903500)+4 种基金the commercial project by Beijing Zhong Dian Hua Yuan Environment Protection Technology Co., Ltd. (E01211200005)the Regional key projects of the science and technology service network program (STS program) of the Chinese Academy of Sciences (KFJ-STS-QYZD-153)the Ningbo Science and Technology Innovation Key Projects (2020Z099, 2022Z028)the Ningbo Municipal Commonweal Key Program (2019C10033)the support of Mineral Resources Analytical and Testing Center, Institute of Process Engineering, Chinese Academy of Science
文摘To achieve the resource utilization of solid waste phosphogypsum(PG)and tackle the problem of utilizing potassium feldspar(PF),a coupled synergistic process between PG and PF is proposed in this paper.The study investigates the features of P and F in PG,and explores the decomposition of PF using hydrofluoric acid(HF)in the sulfuric acid system for K leaching and leaching of P and F in PG.The impact factors such as sulfuric acid concentration,reaction temperature,reaction time,material ratio(PG/PF),liquid–solid ratio,PF particle size,and PF calcination temperature on the leaching of P and K is systematically investigated in this paper.The results show that under optimal conditions,the leaching rate of K and P reach more than 93%and 96%,respectively.Kinetics study using shrinking core model(SCM)indicates two significant stages with internal diffusion predominantly controlling the leaching of K.The apparent activation energies of these two stages are 11.92 kJ·mol^(-1)and 11.55 kJ·mol^(-1),respectively.
文摘This study investigates the use of waste fat biodiesel(WFB)from the leather industry as a substitute for diesel fuel.Specifically,it examines the diesel engine performance of WFB,a blend of WFB and diesel(B50),and different blends of WFB and silicon dioxide(SiO_(2))nanoparticles(B50SiO_(2)40,B50SiO_(2)80,and B50SiO_(2)120μg/g).The results indicate that the B50SiO_(2)120 blend increases brake thermal efficiency by 10.03%compared to pure biodiesel but falls 1.93%short of neat diesel.Furthermore,the B50SiO_(2)120 mixture reduces smoke,hydrocarbon,and carbon monoxide emissions by 31.87%,34.14%,and 43.97%respectively,compared to diesel.However,the B50SiO_(2)120 blend shows a 4.91%increase in nitrogen oxide emissions compared to diesel.
基金supported by the National Natural Science Foundation of China(Grant No.52078034).
文摘During the highway construction,a large number of spoil areas will be generated while a large amount of waste slag and soil could not be rationally utilized.Besides,the vegetation recovery is slow in the spoil areas due to the soil depletion.Aiming at recycling the solid waste,the sieved engineering waste slag with local red clay and corn straw biochar was supplied to solve the problem of insufficient nutrients in engineering waste slag and soil.In addition,planting experiments of alfalfa(Medicago sativa L.)and Amorpha fruticosa L.combined with physical and chemical experiments were carried out to prove the feasibility of the novel improved substrate for the reclamation of spoil areas.The results show that the substrate's improvement effect is mainly affected by the soil to slag ratio and the biochar content.The improvement effect of soil matrix in highway spoil area decreases with the increase of the waste slag content,especially when the soil-slag ratio is less than 3,and the promotion of plants is limited.On the contrary,the improvement effect is proportional to the biochar content(3%-8%).But it is noted that the Cu and Pb in the soil will exceed the clean limit corresponding to the Nemero soil pollution index level when the biochar content is 8%.Therefore,it is recommended that the soil-slag ratio should be≥3,and the biochar content should reach 3%-5%.This research provides experimental basis and technical support for utilizing solid waste resources in the reclamation of highway spoil areas.
基金The authors acknowledge the financial support from the National Natural Science Foundation of China(Nos.52073224,32201491)the Textile Vision Basic Research Program of China(No.J202110)+3 种基金the Scientific Research Project of Shaanxi Provincial Education Department,China(No.22JC035)the Advanced Manufacturing Technology Program of Xi’an Science and Technology Bureau,China(No.21XJZZ0019)the Research Fund for the Doctoral Program of Xi’an Polytechnic University(No.BS202053)the Youth Innovation Team of Shaanxi Universities and Institute of Flexible electronics and Intelligent Textile.
文摘MXene,a transition metal carbide/nitride,has been prominent as an ideal electrochemical active material for supercapacitors.However,the low MXene load limits its practical applications.As environmental concerns and sustainable development become more widely recognized,it is necessary to explore a greener and cleaner technology to recycle textile by-products such as cotton.The present study proposes an effective 3D fabrication method that uses MXene to fabricate waste denim felt into ultralight and flexible supercapacitors through needling and carbonization.The 3D structure provided more sites for loading MXene onto Z-directional fiber bundles,resulting in more efficient ion exchange between the electrolyte and electrodes.Furthermore,the carbonization process removed the specific adverse groups in MXenes,further improving the specific capacitance,energy density,power density and electrical conductivity of supercapacitors.The electrodes achieve a maximum specific capacitance of 1748.5 mF cm-2 and demonstrate remarkable cycling stability maintaining more than 94%after 15,000 galvanostatic charge/discharge cycles.Besides,the obtained supercapacitors present a maximum specific capacitance of 577.5 mF cm^(-2),energy density of 80.2μWh cm^(-2)and power density of 3 mW cm^(-2),respectively.The resulting supercapacitors can be used to develop smart wearable power devices such as smartwatches,laying the foundation for a novel strategy of utilizing waste cotton in a high-quality manner.
基金funded by the National Natural Science Foundation of China (52078068)Postgraduate Research&Practice Innovation Program of Jiangsu Province (SJCX22_1391)+1 种基金the National Science Foundation of Jiangsu Province (BK20220626)Changzhou Leading Innovative Talent Introduction and Cultivation Project (CQ20210085).
文摘As socioeconomic development continues,the issue of building energy consumption has attracted significant attention,and improving the thermal insulation performance of buildings has become a crucial strategic measure.Simultaneously,the application of solid waste in insulation materials has also become a hot topic.This paper reviews the sources and classifications of solid waste,focusing on research progress in its application as insulation materials in the domains of daily life,agriculture,and industry.The research shows that incorporating household solid waste materials,such as waste glass,paper,and clothing scraps into cementitious thermal insulation can significantly reduce the thermal conductivity of the materials,leading to excellent thermal insulation properties.Insulation materials prepared from agricultural solid waste,such as barley straw,corn stalk,chicken feather,and date palm fibers,possess characteristics of lightweight and strong thermal insulation.Industrial solid waste,including waste tires,iron tailings,and coal bottom ash,can also be utilized in the preparation of insulation materials.These innovative applications not only have positive environmental significance by reducing waste emissions and resource consumption,but also provide efficient and sustainable insulation solutions for the construction industry.However,to further optimize the mix design and enhance the durability of insulation materials,continuous research is required to investigate the mechanisms through which solid waste impacts the performance of insulation materials.
文摘Health-care waste contains potentially harmful microorganisms and compounds which can infect and affect hospital patients, healthcare workers, the general public and environment. Therefore, management of health care waste requires safe handling, treatment and disposal procedures. While incineration reduces the volume and quantity of waste for final disposal, it leads to the production of fly and bottom ashes laden with toxic incomplete combustion products such as Polycyclic Aromatic Hydrocarbons (PAHs), dioxins, furans and heavy metals. This exposes workers who handle and dispose the bottom ashes, hospital patients, the general public and environment. The goal of this study was to determine the total and individual levels of 16 most prevalent and toxic PAHs. Bottom ash samples were collected from incinerators in five county hospitals in Kenya, namely;Moi-Voi, Narok, Kitale, Makindu and Isiolo. Bottom ash samples were collected over a period of six months from the five hospitals. The samples were then sieved, homogenised and stored at 4°C in amber coloured glass containers. The PAHs were extracted using 30 ml of a hexane-acetone solvent (1:1) mixture by ultrasonication at room temperature (23°C) for 45 minutes. The PAHs were then analyzed with a GC-MS spectrophotometer model (Shimadzu GCMS-QP2010 SE) connected to a computer work station was used for the PAHs analysis. The GC-MS was equipped with an SGE BPX5 GC capillary column (30 m × 0.25 mm × 0.25 μm) for the separation of compounds. Helium was used as the carrier gas at a flow rate of 15.5 ml/minute and 14.5 psi. 1 μl of the sample was injected at 280°C, split mode (10:1). The oven programming was set for a total runtime of 40 minutes, which included: 100°C (2-minute hold);10°C /min rise to 200°C;7°C /min rise to 249°C;3°C /min rise to 300°C (2-minute hold). The interface temperature was set at 290°C. Analysis was done in Selected Ion Monitoring (SIM) mode and the peak areas of each of the PAHs were collected from the chromatograph and used for quantification of the 16 PAHs listed by the U.S. Environmental Protection Agency (EPA) which included, BaA (benz[a]anthracene: 4 rings), BaP (benzo[a]pyrene: 5 rings), BbF (benzo [b]fluoranthene: 5 rings), BkF (benzo[k]fluoranthene: 5 rings), Chr (chrysene: 4 rings), DbA (dibenz[a,h]anthracene: 5 rings), InP (indeno[1,2,3 - cd] pyrene: 6 rings) and Acp (acenaphthene: 3 rings), Acpy (acenaphthylene: 3 rings), Ant (anthracene: 3 rings), BghiP (benzo[g,h,i]perylene: 6 rings), Flu (fluorene: 3 rings), FluA (fluoranthene: 4 rings), Nap (naphthalene: 2 rings), PhA (phenanthrene: 3 rings) and Pyr (pyrene: 4 rings). Ion source-interface temperature was set at 200°C - 250°C. Internal standards from Sigma Aldrich were used in the analysis and the acquired mass spectra data were then matched against the NIST 2014 library [1] [2]. The mean PAHs concentration in the bottom ashes of each hospital varied broadly from 0.001 mg/kg to 0.4845 mg/kg, and the mean total concentration levels of individual PAHs ranged from 0.0072 mg/kg to 1.171 mg/kg. Low molecular weight PAHs (Phenanthrene, Naphthalene and Fluorene) were predominant in all the hospital wastes whereas Kitale and Narok presented the lowest PAHs concentrations and the lowest number of individual PAHs. Moi/Voi recorded the highest total PAHs concentration at 1.3129 ± 0.0023 mg/kg from a total of 11 PAHs being detected from the bottom ash samples. Narok had only three PAHs being detected at very low concentrations of 0.0041 ± 0.00 mg/kg, 0.0076 ± 0.00 mg/kg and 0.012 ± 0.00 mg/kg for phenanthrene, anthracene and chrysene respectively. This study presents hospital incinerator bottom ash as containing detectable levels of both carcinogenic and non-carcinogenic PAHs. Continued unprotected exposure of hospital workers (waste handlers) to the bottom ash PAHs could be hazardous to their health because of their cumulative effect. Preventive measures e.g. the use of Personal protective equipment (PPE) should be prioritised to minimise direct contact with the bottom ash. The study recommends an upgrade on incinerator technology for efficient combustion processes thus for better pollution control.
基金Funded by the National Natural Science Foundation of China(No.52008046)Young Elite Scientists Sponsorship Program from JSAST(No.TJ-2023-024)Postgraduate Research&Practice Innovation Program of Jiangsu Province(No.KYCX21_2848)。
文摘This study aims to investigate the feasibility of using decoration waste powder(DWP)as a partial replacement for fly ash(FA)in the preparation of geopolymer masonry mortar,and to examine the effect of different DWP replacement rates(0%-40%)on the fresh and mechanical properties of the mortar.The results showed that each group of geopolymer masonry mortar exhibited excellent water retention performance,with a water retention rate of 100%,which was due to the unique geopolymer mortar system and high viscosity of the alkaline activator solution.Compared to the control group,the flowability of the mortar containing lower contents of DWP(10%and 20%)was higher.However,as the DWP replacement rate further increased,the flowability gradually decreased.The DWP could absorb the free water in the reaction system of geopolymer mortar,thereby limiting the occurrence of geopolymerization reaction.The incorporation of DWP in the mortar resulted in a decrease in compressive strength compared to the mortar without DWP.However,even at a replacement rate of 40%,the compressive strength of the mortar still exceeded 15 MPa,which met the requirements of the masonry mortar.It was feasible to use DWP in the geopolymer masonry mortar.Although the addition of DWP caused some performance loss,it did not affect its usability.
文摘Freetown which is the capital city of Sierra Leone is facing challenges with population growth, urbanization, and industrialization, leading to an increase in municipal solid waste (MSW) generation. The study aims to evaluate MSW generation, composition, and disposal methods, as well as the impact of collection fees, policy implementation, and women’s participation in municipal solid waste management (MSWM). The study used both qualitative and quantitative methods for data collection and analysis. The study administered 393 structured questionnaires in three selected sections to collect data on variables such as family size, education, level of knowledge, etc. The study used door-to-door data collection to determine the rate of solid waste generation, composition, and disposal in 66 households from two of the selected sections and 34 households from the other section to evaluate the current situation of MSWM practices among households in Freetown. The study used a descriptive statistic to analyze the data collected using Origin-Pro9 and MS Excel software. The findings showed that with a 4.2% urban growth rate, Freetown had a population of 1,467,543 in 2023, generating 851 tons of MSW per day, with organic waste accounting for 78% of the total MSW generated. Plastic waste generation also increased from 7.6% in 2020 to 13% in 2023. The study emphasizes the need to sustain the MSWM system by prioritizing solid waste collection fees, policy enforcement, and women’s participation in the MSWM sector. It further suggests and provides recommendations for developing an efficient and sustainable MSWM system in Sierra Leone, including knowledge transfer from countries like China and the US.
文摘This investigation is focused on conducting a thorough analysis of Municipal Solid Waste Management (MSWM). MSWM encompasses a range of interdisciplinary measures that govern the various stages involved in managing unwanted or non-utilizable solid materials, commonly known as rubbish, trash, junk, refuse, and garbage. These stages include generation, storage, collection, recycling, transportation, handling, disposal, and monitoring. The waste materials mentioned in this context exhibit a wide range of items, such as organic waste from food and vegetables, paper, plastic, polyethylene, iron, tin cans, deceased animals, byproducts from demolition activities, manure, and various other discarded materials. This study aims to provide insights into the possibilities of enhancing solid waste management in the Farmgate area of Dhaka North City Corporation (DNCC). To accomplish this objective, the research examines the conventional waste management methods employed in this area. It conducts extensive field surveys, collecting valuable data through interviews with local residents and key individuals involved in waste management, such as waste collectors, dealers, intermediate dealers, recyclers, and shopkeepers. The results indicate that significant amounts of distinct waste categories are produced daily. These include food and vegetable waste, which amount to 52.1 tons/day;polythene and plastic, which total 4.5 tons/day;metal and tin-can waste, which amounts to 1.4 tons/day;and paper waste, which totals 5.9 tons/day. This study highlights the significance of promoting environmental consciousness to effectively shape the attitudes of urban residents toward waste disposal and management. It emphasizes the need for collaboration between authorities and researchers to improve the current waste management system.
基金Under the auspices of the General Program of National Natural Science Foundation of China(No.42271112)General Research Project of Beijing Municipal Commission of Education Science(No.KM202011417008)。
文摘Due to the acceleration of urbanization,the municipal waste(MW)problem has transformed into a global challenge for urb-an sustainability.To elucidate historical trends,current focal points,and future directions in MW research,we conducted a bibliometric analysis and employed knowledge graph visualization to scrutinize a total of 34212 articles,which were published between 1991 and 2021 in the Web of Science(WoS)core database.The results indicated that current major research themes encompass waste classifica-tion and recycling,waste management and public behavior,waste disposal methods and technologies,as well as environmental impact and evaluation.There has been a shift in the research focus from the environmental impacts of waste incineration to sustainable manage-ment related issues.A comparison of research from six typical countries revealed the differences in research priorities and techniques advantages.Scholars from the USA and Britain initiated MW research earlier than other countries and investigated management issues in depth,such as public behavior and willingness to pay.Meanwhile,Japanese,German,and Swedish scholars conducted extensive studies on advanced waste treatment technologies,such as disposal and recycling,risk assessment,and waste-to-energy techniques.Chinese scholars placed particular emphasis on end-of-pipe treatments and their associated environmental impacts.Hotspots and poten-tial future frontiers were identified by burst detection analysis.Keywords with high value of burst index(BI)worldwide are food waste and circular economy.Chinese scholars have put great efforts on waste environmental impact and its recycling technologies,while we’re expecting to further investigating vulnerable population.Furthermore,this study contributes to bridging the regional gap of scientific research among different countries and fostering international collaboration.
文摘Despite the fact that a few countries in the Mediterranean and the Middle East have limited crude oil reserves, they have abundant biomass feedstocks. For instance, Jordan relies heavily on the importation of natural gas and crude oil for its energy needs;but, by applying thermochemical conversion techniques, leftover olive oil can be used to replace these energy sources. Understanding the chemical, physical, and thermal characteristics of raw materials is essential to obtaining the most out of these conversion processes. Thermogravimetric analysis was used in this study to examine the thermal behavior of olive-solid residue (kernel) at three different heating rates (5, 20 and 40 C/min) in nitrogen and oxygen atmospheres. The initial degradation temperature, the residual weight at 500 and 700˚C and the thermal degradation rate during the devolatilization stage (below 400˚C) were all determined. It was found that in N<sub>2</sub> and O<sub>2</sub> atmospheres, both the initial degradation temperature and the degradation rate increase with increasing heating rates. As heating rates increase in the N<sub>2</sub> atmosphere, the residual weight at 500 or 700˚C decreases slightly, but at low heating rates compared to high heating rates in the O<sub>2</sub> atmosphere, it decreases significantly. This suggests that a longer lignin oxidation process is better than a shorter one. Coats and Redfern approach was used to identify the mechanism and activation energy for the devolatilization stage of pyrolysis and oxidation reactions. The process mechanism analysis revealed that the model of first-order and second-order reactions may adequately describe the mechanism of heat degradation of the devolatilization step of olive-solid waste for pyrolysis and oxidation processes, respectively.
文摘The production and consumption of avocado pears generates tons of wastes, mainly the pear peels which are usually discarded, although they have been reported to contain important phyto-chemicals with biological activities. The adverse health effect associated with the consumption of saturated lipid based foods has ignited research on reformulation of lipid based foods to eliminate Trans Fatty Acids (TFAs). This study was thus aimed at the extraction and characterization of oil from Avocado Peels (APO) and evaluation of the quality of margarine produced from it. Five verities of pear were used for oil extraction by soxhlet method and physiochemical, oxidative, functional and antioxidant characterization was done. Margarines were formulated using a central composite design using oil blends of APO and Virgin Coconut Oil (VCO) with an oil ratio of 10:90, 40:60, 70:30 respectively, varied blending speed, blending time, and chitosan concentration. Samples were characterized and the effect of process parameters on the physiochemical and functional properties of the margarine studied. Optimized conditions were used to produce samples for sensory evaluation. Color, spreadability, aroma, taste and general acceptability was evaluated using ranking difference test. The results showed that the yield, density, and iodine values of APOs oils ranged from 14.91 ± 0.18 to 11.76 ± 0.46;0.93 ± 0.001 to 0.99 ± 0.1;46.63 ± 1.70 to 52.4 ± 0.63, their acid values, TBA and PV values ranged from 1.42 ± 0.39 to 1.97 ± 0.5;0.11 ± 0.002 to 0.18 ± 0.04;and 2.72 ± 0.14 to 4.43 ± 0.36 respectively, with Brogdon avocado peel variety having the overall best properties prepared blends of trans-free APO margarines showed that increase in APO ratio decreased melting point, increased oxidative stability and reduced moisture content of margarine samples. Chitosan addition leads to decrease moisture content and increase functional properties. VCO lead to increase in phenolic and flavonoid content of the margarines. Samples were spreadable and palatable with R20 being most palatable and the most accepted being R26 with a mean score of 7.07 ± 0.70. Decrease in color intensity increased acceptability. This study therefore demonstrated that avocado peel waste biomass can be valorized by using it as raw material for oil extraction, which can serve as good material for the production of trans-free margarines with good oxidative stability, functional and antioxidant properties.
文摘The mining process involves drilling and excavation, resulting in the production of waste rock and tailings. The waste materials are then removed and stored in designated areas. This study aims to evaluate the mechanical strength and the environmental and economic impact of using Coltan Mining Waste (CMW) as a substitute for aggregates in concrete and mortar production. To achieve this, the CMW needs to be characterised. The Dreux Gorisse method was primarily used to produce concrete with a strength of 20 MPa at 28 days. The mortars, on the other hand, were formulated according to the NF P 18-452 standard. The environmental impact of using CMW as substitutes for natural aggregates in the production of concrete and mortar was analysed using SimaPro software. The results showed that mortars and concrete made with CMW have comparable compressive strengths to the reference mortar and concrete;reduce the negative impact on ecosystem quality, human health, resources, and climate change. It has also been shown that the substitution of aggregates by CMW reduces the cost of concrete and mortar as a function of the distance from the aggregate footprint.
基金supported by the National Natural Science Foundation of China (No.52364022)the Natural Science Foundation of Guangxi Province,China (Nos.2023JJA160192 and 2021GXNSFAA220096)+1 种基金the Guangxi Science and Technology Major Project,China (No.AA23073018)the Guangxi Chongzuo Science and Technology Plan,China (No.2023ZY00503).
文摘With the application of resins in various fields, numerous waste resins that are difficult to treat have been produced. The industrial wastewater containing Cr(Ⅵ) has severely polluted soil and groundwater environments, thereby endangering human health. Therefore, in this paper, a novel functionalized mesoporous adsorbent PPR-Z was synthesized from waste amidoxime resin for adsorbing Cr(Ⅵ). The waste amidoxime resin was first modified with H3PO4 and ZnCl_(2), and subsequently, it was carbonized through slow thermal decomposition. The static adsorption of PPR-Z conforms to the pseudo-second-order kinetic model and Langmuir isotherm, indicating that the Cr(Ⅵ) adsorption by PPR-Z is mostly chemical adsorption and exhibits single-layer adsorption. The saturated adsorption capacity of the adsorbent for Cr(Ⅵ) could reach 255.86 mg/g. The adsorbent could effectively reduce Cr(Ⅵ) to Cr(Ⅲ) and decrease the toxicity of Cr(Ⅵ) during adsorption. PPR-Z exhibited Cr(Ⅵ) selectivity in electroplating wastewater. The main mechanisms involved in the Cr(Ⅵ) adsorption are the chemical reduction of Cr(Ⅵ) into Cr(Ⅲ) and electrostatic and coordination interactions. Preparation of PPR-Z not only solves the problem of waste resin treatment but also effectively controls Cr(Ⅵ) pollution and realizes the concept of “treating waste with waste”.
文摘Waste production rises in tandem with population growth and increased utilization.The indecorous disposal of waste paves the way for huge disaster named as climate change.The National Environment Agency(NEA)of Singapore oversees the sustainable management of waste across the country.The three main contributors to the solid waste of Singapore are paper and cardboard(P&C),plastic,and food scraps.Besides,they have a negligible rate of recycling.In this study,Machine Learning techniques were utilized to forecast the amount of garbage also known as waste audits.The waste audit would aid the authorities to plan their waste infrastructure.The applied models were k-nearest neighbors,Support Vector Regressor,ExtraTrees,CatBoost,and XGBoost.The XGBoost model with its default parameters performed better with a lower Mean Absolute Percentage Error(MAPE)of 8.3093(P&C waste),8.3217(plastic waste),and 6.9495(food waste).However,Grid Search Optimization(GSO)was used to enhance the parameters of the XGBoost model,increasing its effectiveness.Therefore,the optimized XGBoost algorithm performs the best for P&C,plastics,and food waste with MAPE of 4.9349,6.7967,and 5.9626,respectively.The proposed GSO-XGBoost model yields better results than the other employed models in predicting municipal solid waste.
基金financially supported by the National Natural Science Foundation of China (22279122,52042403)the Zhejiang Provincial Natural Science Foundation of China (LZ22B030004)+2 种基金the Ministry of Education,Singapore,under its Academic Research Fund Tier 1 (RG10/22)the National Institute of Education,Singapore,under its Academic Research Fund (RI 1/21 EAH)National Institute of Education,Singapore,under its Start-Up Grant (NIE-SUG4/20AHX)。
文摘Zinc metal is a promising anode material for next-generation aqueous batteries,but its practical application is limited by the formation of zinc dendrite.To prevent zinc dendrite growth,various Zn^(2+)-conducting but water-isolating solid-electrolyte interphase(SEI)films have been developed,however,the required high-purity chemical materials are extremely expensive.In this work,phosphogypsum(PG),an industrial byproduct produced from the phosphoric acid industry,is employed as a multifunctional protective layer to navigate uniform zinc deposition.Theoretical and experimental results demonstrate that PG-derived CaSO_(4)2H_(2)O can act as an artificial SEI layer to provide fast channels for Zn^(2+)transport.Moreover,CaSO_(4)2H_(2)O could release calcium ions(Ca^(2+))due to its relatively high Kspvalue,which have a higher binding energy than that of Zn^(2+)on the Zn surface,thus preferentially adsorbing to the tips of the protuberances to force zinc ions to nucleate at inert region.As a result,the Zn@PG anode achieves a high Coulombic efficiency of 99.5%during 500 cycles and long-time stability over 1000 hours at 1 m A cm^(-2).Our findings will not only construct a low-cost artificial SEI film for practical metal batteries,but also achieve a high-value utilization of phosphogypsum waste.
基金the financial support from the National Natural Science Foundation of China(21908010)Jilin Provincial Department of Science and Technology(20220101089JC)the Education Department of Jilin Province(JJKH20220694KJ)。
文摘Globally,the efficient utilization of polymer wastes is one of the most important issues for current sustainable development topics.Herein,a green and efficient low-temperature combustion approach is proposed to deal with polymer wastes and recover heat energy,simultaneously alleviating the environment and energy crisis.Non-noble metal oxides(Al_(2)O_(3),Fe_(2)O_(3),NiO_(2),ZrO_(2),La_(2)O_(3)and CeO_(2)) were prepared,characterized and screened to boost the low-temperature combustion of polyethylene waste at 300℃ in air.The mass change,heat release and CO_(x) formation were studied in details and employed to evaluate the combustion rate and efficiency.It was found that CeO_(2)significantly enhanced the combustion rate and efficiency,which was respectively 2 and 7 times that of non-catalytic case.An interesting phenomenon was observed that the catalytic performance of CeO_(2) in polyethylene low-temperature combustion was significantly improved by the 7-day storage in the room environment or water treatment.XPS analysis confirmed the co-existence of Ce^(3+) and Ce^(4+) in CeO_(2),and the 7-day storage and water treatment promoted the amount of Ce^(3+),which facilitated the formation of the oxygen vacancies.That may be the reason why CeO_(2) exhibited excellent catalytic performance in polyethylene low-temperature combustion.
基金supported by the Foundation of Henan Key Laboratory of Underwater Intelligent Equipment under Grant No.KL02C2105Project of SongShan Laboratory under Grant No.YYJC062022012+2 种基金Training Plan for Young Backbone Teachers in Colleges and Universities in Henan Province under Grant No.2021GGJS077Key Scientific Research Projects of Colleges and Universities in Henan Province under Grant No.22A460022North China University of Water Resources and Electric Power Young Backbone Teacher Training Project under Grant No.2021-125-4.
文摘With the continuous development of the economy and society,plastic pollution in rivers,lakes,oceans,and other bodies of water is increasingly severe,posing a serious challenge to underwater ecosystems.Effective cleaning up of underwater litter by robots relies on accurately identifying and locating the plastic waste.However,it often causes significant challenges such as noise interference,low contrast,and blurred textures in underwater optical images.A weighted fusion-based algorithm for enhancing the quality of underwater images is proposed,which combines weighted logarithmic transformations,adaptive gamma correction,improved multi-scale Retinex(MSR)algorithm,and the contrast limited adaptive histogram equalization(CLAHE)algorithm.The proposed algorithm improves brightness,contrast,and color recovery and enhances detail features resulting in better overall image quality.A network framework is proposed in this article based on the YOLOv5 model.MobileViT is used as the backbone of the network framework,detection layer is added to improve the detection capability for small targets,self-attention and mixed-attention modules are introduced to enhance the recognition capability of important features.The cross stage partial(CSP)structure is employed in the spatial pyramid pooling(SPP)section to enrich feature information,and the complete intersection over union(CIOU)loss is replaced with the focal efficient intersection over union(EIOU)loss to accelerate convergence while improving regression accuracy.Experimental results proved that the target recognition algorithm achieved a recognition accuracy of 0.913 and ensured a recognition speed of 45.56 fps/s.Subsequently,Using red,green,blue and depth(RGB-D)camera to construct a system for identifying and locating underwater plastic waste.Experiments were conducted underwater for recognition,localization,and error analysis.The experimental results demonstrate the effectiveness of the proposed method for identifying and locating underwater plastic waste,and it has good localization accuracy.