期刊文献+
共找到2篇文章
< 1 >
每页显示 20 50 100
3D seismic forward modeling from the multiphysical inversion at the Ketzin CO_(2) storage site
1
作者 Yi-kang Zheng Chong Wang +2 位作者 Hao-hong Liang Yi-bo Wang Rong-shu Zeng 《Applied Geophysics》 SCIE CSCD 2024年第3期593-605,620,共14页
From June 2008 to August 2013,approximately 67 kt of CO_(2) was injected into a deep saline formation at the Ketzin pilot CO_(2) storage site.During injection,3D seismic surveys have been performed to monitor the migr... From June 2008 to August 2013,approximately 67 kt of CO_(2) was injected into a deep saline formation at the Ketzin pilot CO_(2) storage site.During injection,3D seismic surveys have been performed to monitor the migration of sequestered CO_(2).Seismic monitoring results are limited by the acquisition and signal-to-noise ratio of the acquired data.The multiphysical reservoir simulation provides information regarding the CO_(2) fluid behavior,and the approximated model should be calibrated with the monitoring results.In this work,property models are delivered from the multiphysical model during 3D repeated seismic surveys.The simulated seismic data based on the models are compared with the real data,and the results validate the effectiveness of the multiphysical inversion method.Time-lapse analysis shows the trend of CO_(2) migration during and after injection. 展开更多
关键词 Seismic forward modeling reservoir simulation CO_(2)storage time-lapse analysis
下载PDF
利用粒子群算法实现陀螺仪耦合系统动态响应优化 被引量:1
2
作者 王继寅 薛旭 《电子器件》 CAS 北大核心 2021年第4期980-986,共7页
利用平均法分析半球陀螺仪控制系统,得到通过PID模块实现的深度负反馈控制回路设计。根据大机动平台等对陀螺仪系统快速响应的要求,寻求方法对深度负反馈控制的PID参数整定以实现输出动态优化。系统中耦合项的存在是控制参数设计的难点... 利用平均法分析半球陀螺仪控制系统,得到通过PID模块实现的深度负反馈控制回路设计。根据大机动平台等对陀螺仪系统快速响应的要求,寻求方法对深度负反馈控制的PID参数整定以实现输出动态优化。系统中耦合项的存在是控制参数设计的难点。通过参数变换和输出结果分析,发现系统PID参数与系统动态响应之间没有明显的相关性,不能通过拟合方式去实现优化。将系统的耦合关系去除,通过以往设计带宽的方式得到了系统的优化参数。利用ITAE评价标准作为适应度函数,得到利用粒子群算法(PSO算法)优化后的控制系统,通过比对两者的系统带宽和ITAE输出,在带宽近似的情况下,PSO优化比传统去耦合优化的ITAE标准由49.8下降到了0.36,调节时间由1.049 s下降到了0.0905 s,大大优化了系统的输出的动态响应。 展开更多
关键词 陀螺仪耦合系统 PID控制 粒子群(PSO)算法 误差积评价标准
下载PDF
上一页 1 下一页 到第
使用帮助 返回顶部