A crystal plasticity finite element model was developed for the drawing deformation of pure copper micro wire,based on rate-dependent crystal plasticity theory.The impact of wire diameter compression ratio on the micr...A crystal plasticity finite element model was developed for the drawing deformation of pure copper micro wire,based on rate-dependent crystal plasticity theory.The impact of wire diameter compression ratio on the micro-mechanical deformation behavior during the wire drawing process was investigated.Results indicate that the internal deformation and slip of the drawn wire are unevenly distributed,forming distinct slip and non-slip zones.Additionally,horizontal strain concentration bands develop within the drawn wire.As the wire diameter compression ratio increases,the strength of the slip systems and the extent of slip zones inside the deformation zone also increase.However,the fluctuating stress state,induced by contact pressure and frictional stress,results in a rough and uneven wire surface and diminishes the stability of the drawing process.展开更多
CNTs-Cu and graphite-Cu composites were separately prepared by powder metallurgy technique under the same consolidation processing. Tribological behavior of the composites with electric current was investigated by usi...CNTs-Cu and graphite-Cu composites were separately prepared by powder metallurgy technique under the same consolidation processing. Tribological behavior of the composites with electric current was investigated by using a pin-on-disk friction and wear tester. The results show that the friction coefficient and wear rate of the composites decrease with increasing the reinforcement content, and increase with increasing the electric current density; the effects of electric current are more obvious on tribological properties of graphite-Cu composites than on CNTs-Cu composites; for graphite-Cu composites the dominant wear mechanisms are electric arc erosion and adhesive wear, while for CNTs-Cu composites are adhesive wear.展开更多
The Mo alloys reinforced by Al2O3 particles were fabricated by hydrothermal synthesis and powder metallurgy. The microstructures of Mo-Al2O3 alloys were studied by using XRD, SEM and TEM. The results show that Al2O3 p...The Mo alloys reinforced by Al2O3 particles were fabricated by hydrothermal synthesis and powder metallurgy. The microstructures of Mo-Al2O3 alloys were studied by using XRD, SEM and TEM. The results show that Al2O3 particles, existing as a stable hexagonal phase(α-Al2O3), are uniformly dispersed in Mo matrix. The ultrafine α-Al2O3 particles remarkably refine grain size and increase dislocation density of Mo alloys. Moreover, a good interfacial bonding zone between α-Al2O3 and Mo grain is obtained. The crystallographic orientations of the interface of the Al2O3 particles and Mo matrix are [111]a-Al2O3//[111]Mo and(112)a-Al2O3//(0 11)Mo. Due to the effect of secondary phase and dislocation strengthening, the yield strength of Mo-2.0 vol.%Al2O3 alloy annealed at 1200 ℃ is approximately 56.0% higher than that of pure Mo. The results confirm that the addition of Al2O3 particles is a promising method to improve the mechanical properties of Mo alloys.展开更多
To disclose the effect of contact force and electrode gap on the material transfer behavior of Ag-based contact material, arc-erosion tests of the Ag-4wt.%TiB2 contact material were performed for 5000 operations at 24...To disclose the effect of contact force and electrode gap on the material transfer behavior of Ag-based contact material, arc-erosion tests of the Ag-4wt.%TiB2 contact material were performed for 5000 operations at 24 V/16 A under resistive load on an electric contact material testing system. The arc energy and arc duration were investigated, the surface morphologies of eroded anode and cathode were characterized, the mass changes after arc-erosion tests were determined, and the material transfer behavior was discussed as well. The results show that contact force has a significant effect on the arc energy, arc duration and erosion morphology, but has no impact on the material transfer mode. However, electrode gap not only influences the arc energy, arc duration and surface morphology, but also changes the material transfer mode. At 1 mm, the material transfers from anode to cathode. Nevertheless, an opposite mode presents at 4 mm, which is from cathode to anode.展开更多
The widespread utilization of fossil fuels has caused an associated increase in CO_(2) emissions over the past few decades,which has resulted in global warming and ocean acidification.CO hydrogenation(Fischer‐Tropsch...The widespread utilization of fossil fuels has caused an associated increase in CO_(2) emissions over the past few decades,which has resulted in global warming and ocean acidification.CO hydrogenation(Fischer‐Tropsch synthesis,FTS)is considered a significant route for the production of liquid fuels and chemicals from nonpetroleum sources to meet worldwide demand.Conversion of CO_(2) with renewable H_(2) into valuable hydrocarbons is beneficial for reducing dependence on fossil fuels and mitigating the negative effects of high CO_(2) concentrations in the atmosphere.Iron‐based catalysts exhibit superior catalytic performance in both FTS and CO_(2) hydrogenation to value‐added hydrocarbons.The abundance and low cost of iron‐based catalysts also promote their wide application in CO_(x) hydrogenation.This paper provides a comprehensive overview of the significant developments in the application of iron‐based catalysts in these two fields.The active phases,promoter effect,and support of iron‐based catalysts are discussed in the present paper.Based on understanding of these three essential aspects,we also cover recent advances in the design and preparation of novel iron‐based catalysts for FTS and CO_(2) hydrogenation.Current challenges and future catalytic applications are also outlined.展开更多
Aiming at the problems of low reliability and complex operation of traditional coin-tap test of composite material,this paper introduces the grey system theory and achieves better performance.The response signals of c...Aiming at the problems of low reliability and complex operation of traditional coin-tap test of composite material,this paper introduces the grey system theory and achieves better performance.The response signals of coin-tap are classified through the grey clustering based on relation analysis,and corresponding improvements are made to the calculation method of the relation degree of nearness.First,the time history of acceleration is taken as the system behavior sequence.The improved correlation calculation method is used to solve the relation degree of nearness between the sequences,and the matrix of degree of grey relation is constructed based on this.Then,the sequence groups are summarized through the matrix,and the response signals of coin-tap are qualitatively classified according to the location of the reference sequence.Finally,the defect detection of composite materials is completed without pre-testing.The test results show that the accuracy of the coin-tap test based on improved grey clustering reaches 100%,which simplifies the operation steps while ensuring the reliability of the coin-tap test results.展开更多
In the process of tobacco production, the moisture content of tobacco leaves directly affects the quality of tobacco leaf. Since the water content in the leaf is low, it needs to process with the conditioning treatmen...In the process of tobacco production, the moisture content of tobacco leaves directly affects the quality of tobacco leaf. Since the water content in the leaf is low, it needs to process with the conditioning treatment for a short time beforetobacco grading, so as to improve the tobacco moisture content and reduce breakage, as well as ensure the quality and yield of tobacco, ahd meet the requirements of the follow-up process of tobacco. Therefore, a comprehensive overview was given to the pre-conditioning method for tobacco leaf, and the current application status of tobacco leaf pre-conditioning equipment in China was explored.展开更多
基金the National Natural Science Foundation of China(Nos.U21A2051,52173297,52071133)the R&D Projects of Henan Academy of Sciences of China(No.220910009)+2 种基金the Key R&D and Promotion Projects of Henan Province of China(No.212102210441)the Joint Fund of Henan Science and Technology R&D Plan of China(No.222103810037)the Zhongyuan Scholar Workstation Funded Project of China(No.214400510028).
文摘A crystal plasticity finite element model was developed for the drawing deformation of pure copper micro wire,based on rate-dependent crystal plasticity theory.The impact of wire diameter compression ratio on the micro-mechanical deformation behavior during the wire drawing process was investigated.Results indicate that the internal deformation and slip of the drawn wire are unevenly distributed,forming distinct slip and non-slip zones.Additionally,horizontal strain concentration bands develop within the drawn wire.As the wire diameter compression ratio increases,the strength of the slip systems and the extent of slip zones inside the deformation zone also increase.However,the fluctuating stress state,induced by contact pressure and frictional stress,results in a rough and uneven wire surface and diminishes the stability of the drawing process.
基金Project (2007CB607603) supported by the National Basic Research Program of China
文摘CNTs-Cu and graphite-Cu composites were separately prepared by powder metallurgy technique under the same consolidation processing. Tribological behavior of the composites with electric current was investigated by using a pin-on-disk friction and wear tester. The results show that the friction coefficient and wear rate of the composites decrease with increasing the reinforcement content, and increase with increasing the electric current density; the effects of electric current are more obvious on tribological properties of graphite-Cu composites than on CNTs-Cu composites; for graphite-Cu composites the dominant wear mechanisms are electric arc erosion and adhesive wear, while for CNTs-Cu composites are adhesive wear.
基金Projects(U1704152,U1804124)supported by the National Natural Science Foundation of ChinaProject(174100510012)supported by Plan for Scientific Innovation Talent of Henan Province,China。
文摘The Mo alloys reinforced by Al2O3 particles were fabricated by hydrothermal synthesis and powder metallurgy. The microstructures of Mo-Al2O3 alloys were studied by using XRD, SEM and TEM. The results show that Al2O3 particles, existing as a stable hexagonal phase(α-Al2O3), are uniformly dispersed in Mo matrix. The ultrafine α-Al2O3 particles remarkably refine grain size and increase dislocation density of Mo alloys. Moreover, a good interfacial bonding zone between α-Al2O3 and Mo grain is obtained. The crystallographic orientations of the interface of the Al2O3 particles and Mo matrix are [111]a-Al2O3//[111]Mo and(112)a-Al2O3//(0 11)Mo. Due to the effect of secondary phase and dislocation strengthening, the yield strength of Mo-2.0 vol.%Al2O3 alloy annealed at 1200 ℃ is approximately 56.0% higher than that of pure Mo. The results confirm that the addition of Al2O3 particles is a promising method to improve the mechanical properties of Mo alloys.
基金Projects(51274163,51605146) supported by the National Natural Science Foundation of ChinaProject(U1502274) supported by Key Program of the National Natural Science Foundation of China+2 种基金Project(2018M632769) supported by the China Postdoctoral Science FoundationProject(2017SKY-WK010) supported by the Research Fund of Shaanxi Key Laboratory of Comprehensive Utilization of Tailings Resources,ChinaProject(18JK0722) supported by Special Research Program of Shaanxi Provincial Department of Education,China
文摘To disclose the effect of contact force and electrode gap on the material transfer behavior of Ag-based contact material, arc-erosion tests of the Ag-4wt.%TiB2 contact material were performed for 5000 operations at 24 V/16 A under resistive load on an electric contact material testing system. The arc energy and arc duration were investigated, the surface morphologies of eroded anode and cathode were characterized, the mass changes after arc-erosion tests were determined, and the material transfer behavior was discussed as well. The results show that contact force has a significant effect on the arc energy, arc duration and erosion morphology, but has no impact on the material transfer mode. However, electrode gap not only influences the arc energy, arc duration and surface morphology, but also changes the material transfer mode. At 1 mm, the material transfers from anode to cathode. Nevertheless, an opposite mode presents at 4 mm, which is from cathode to anode.
文摘The widespread utilization of fossil fuels has caused an associated increase in CO_(2) emissions over the past few decades,which has resulted in global warming and ocean acidification.CO hydrogenation(Fischer‐Tropsch synthesis,FTS)is considered a significant route for the production of liquid fuels and chemicals from nonpetroleum sources to meet worldwide demand.Conversion of CO_(2) with renewable H_(2) into valuable hydrocarbons is beneficial for reducing dependence on fossil fuels and mitigating the negative effects of high CO_(2) concentrations in the atmosphere.Iron‐based catalysts exhibit superior catalytic performance in both FTS and CO_(2) hydrogenation to value‐added hydrocarbons.The abundance and low cost of iron‐based catalysts also promote their wide application in CO_(x) hydrogenation.This paper provides a comprehensive overview of the significant developments in the application of iron‐based catalysts in these two fields.The active phases,promoter effect,and support of iron‐based catalysts are discussed in the present paper.Based on understanding of these three essential aspects,we also cover recent advances in the design and preparation of novel iron‐based catalysts for FTS and CO_(2) hydrogenation.Current challenges and future catalytic applications are also outlined.
基金National Key Research and Development Project of China(No.2018YFB1701200)。
文摘Aiming at the problems of low reliability and complex operation of traditional coin-tap test of composite material,this paper introduces the grey system theory and achieves better performance.The response signals of coin-tap are classified through the grey clustering based on relation analysis,and corresponding improvements are made to the calculation method of the relation degree of nearness.First,the time history of acceleration is taken as the system behavior sequence.The improved correlation calculation method is used to solve the relation degree of nearness between the sequences,and the matrix of degree of grey relation is constructed based on this.Then,the sequence groups are summarized through the matrix,and the response signals of coin-tap are qualitatively classified according to the location of the reference sequence.Finally,the defect detection of composite materials is completed without pre-testing.The test results show that the accuracy of the coin-tap test based on improved grey clustering reaches 100%,which simplifies the operation steps while ensuring the reliability of the coin-tap test results.
基金Supported by the Project of Zhengzhou Tobacco Company of Henan Province(201415)~~
文摘In the process of tobacco production, the moisture content of tobacco leaves directly affects the quality of tobacco leaf. Since the water content in the leaf is low, it needs to process with the conditioning treatment for a short time beforetobacco grading, so as to improve the tobacco moisture content and reduce breakage, as well as ensure the quality and yield of tobacco, ahd meet the requirements of the follow-up process of tobacco. Therefore, a comprehensive overview was given to the pre-conditioning method for tobacco leaf, and the current application status of tobacco leaf pre-conditioning equipment in China was explored.
