Three-channel CMOS transimpedance amplifier for LiDAR sensor receiver

For time-of-flight(TOF)light detection and ranging(LiDAR),a three-channel high-performance transimpedance amplifier(TIA)with high immunity to input load capacitance is presented.A regulated cascade(RGC)as the input stage is at the core of the complementary metal oxide semiconductor(CMOS)circuit chip,giving it more immunity to input photodiode detectors.A simple smart output interface acting as a feedback structure,which is rarely found in other designs,reduces the chip size and power consumption simultaneously.The circuit is designed using a 0.5μm CMOS process technology to achieve low cost.The device delivers a 33.87 dB?transimpedance gain at 350 MHz.With a higher input load capacitance,it shows a-3 dB bandwidth of 461 MHz,indicating a better detector tolerance at the front end of the system.Under a 3.3 V supply voltage,the device consumes 5.2 mW,and the total chip area with three channels is 402.8×597.0μm2(including the test pads).

Highly Efficient Continuous-Wave Mid-Infrared Intracavity Singly Resonant Optical Parametric Oscillator Based on MgO：PPLN

我们在场紧缩的所有固态的 cw 中间红外线的 intracavity 基于自我制作的 1-mm-thick 40-mm-long 的单身地反响的光参量的振荡器(OPO ) 周期性地做了 MgO poled 锂 niobate (MgO : PPLN ) 。在 15.6 W 的二极管泵力量，紧缩的 intracavity Nd : YVO4/MgO : PPLN OPO 在 3.19mm 生产了 1.9 W 产量力量，相应于到 OPO 更闲散的输出的从激光二极管泵的 12.2% 的变换效率。[从作者抽象]

Optimal design of near-Earth asteroid sample-return trajectories in the Sun–Earth–Moon system

In the 6th edition of the Chinese Space Trajectory Design Competition held in 2014, a near-Earth asteroid sample-return trajectory design problem was released, in which the motion of the spacecraft is modeled in multi-body dynamics, considering the gravitational forces of the Sun, Earth, and Moon. It is proposed that an electric-propulsion spacecraft initially parking in a circular 200-kin-altitude low Earth orbit is expected to rendezvous with an asteroid and carry as much sample as possible back to the Earth in a 10-year time frame. The team from the Technology and Engineering Center for Space Utilization, Chinese Academy of Sciences has reported a solution with an asteroid sample mass of 328 tons, which is ranked first in the competition. In this article, we will present our design and optimization methods, primarily including overall analysis, target selection, escape from and capture by the Earth-Moon system, and optimization of impulsive and low-thrust trajectories that are modeled in multi-body dynamics. The orbital resonance concept and lunar gravity assists are considered key techniques employed for trajectory design. The reported solution, preliminarily revealing the feasibility of returning a hundreds-of-tons asteroid or asteroid sample, envisions future space missions relating to near-Earth asteroid exploration.

Improved direct P code acquisition technique

P code direct acquisition is an important technology in satellite navigation system. As the P code has a long period, it is hard to directly acquire. The traditional average method can process multiple code phases in a time to shorten the acquisition time. But with the increase of average phase error of the input signal and the local code, the correlation signal-to-noise ratio （SNR） loss increases. To reduce the SNR loss, an improved average method is introduced. A new sequence is generated with a summation of phase shifting sequences to decrease correlation peak loss. Simulation results show that compared with direct average method, the improved average method effectively increases correlation SNR.

空间通信中超高动态扩频信号的高灵敏度捕获方法(英文)

According to the requirements of the high-sensitivity acquisition of Direct Sequence Spread Spectrum(DSSS) signals under ultrahigh dynamic environments in space communications, a three-dimensional joint search of the phase of Pseudo-Noise-code(PN-code),Doppler frequency and its rate-of-change is presented to achieve high sensitivity in sensing high-frequency dynamics. By eliminating the correlation peak loss caused by ultrahigh Doppler frequency and its rate-of-change offset,the proposed method improves the acquisition sensitivity by increasing the non-coherent accumulation time. The validity of the algorithm is proved by theoretical analysis and simulation results. It is shown that signals with a carrier- to-noise ratio as low as 39 dBHz can be captured with high performance when the Doppler frequency is up to ±1 MHz and its rate-of-change is up to ±200 kHz/s.

Attack on Optical Double Random Phase Encryption Based on the Principle of Ptychographical Imaging

The principle of ptychography is applied in known plain text attack on the double random phase encoding （DRPE） system. We find that with several pairs of plain texts and cipher texts, the model of attack on DRPE can be converted to the model of ptyehographical imaging. Owing to the inherent merits of the ptyehographical imaging, the DRPE system can be breached totally in a fast and nearly perfect way, which is unavailable for currently existing attack methods. Further, since the decryption keys can be seen as an object to be imaged from the perspective of imaging, the ptychographical technique may be a kind of new direction to further analysis of the security of other encryption systems based on double random keys.

Earth-moon Trajectory Optimization Using Solar Electric Propulsion

The optimization of the Earth-moon trajectory using solar electric propulsion is presented. A feasible method is proposed to optimize the transfer trajectory starting from a low Earth circular orbit （500 km altitude） to a low lunar circular orbit （200 km altitude）. Due to the use of low-thrust solar electric propulsion, the entire transfer trajectory consists of hundreds or even thousands of orbital revolutions around the Earth and the moon. The Earth-orbit ascending （from low Earth orbit to high Earth orbit） and lunar descending （from high lunar orbit to low lunar orbit） trajectories in the presence of J2 perturbations and shadowing effect are computed by an analytic orbital averaging technique. A direct/indirect method is used to optimize the control steering for the trans-lunar trajectory segment, a segment from a high Earth orbit to a high lunar orbit, with a fixed thrust-coast-thrust engine sequence. For the trans-lunar trajectory segment, the equations of motion are expressed in the inertial coordinates about the Earth and the moon using a set of nonsingular equinoctial elements inclusive of the gravitational forces of the sun, the Earth, and the moon. By way of the analytic orbital averaging technique and the direct/indirect method, the Earth-moon transfer problem is converted to a parameter optimization problem, and the entire transfer trajectory is formulated and optimized in the form of a single nonlinear optimization problem with a small number of variables and constraints. Finally, an example of an Earth-moon transfer trajectory using solar electric propulsion is demonstrated.

An OGC standard-oriented architecture for distributed coal mine map services

GIS- or CAD-based technology has been widely used for cartographic maps in coal mines, but structural gaps between such maps make it difficult to provide an integrated map service, for any specific purpose, at higher levels. There is no uniform platform that can be used to manage all involved maps. The main reason for this is that datasets are submitted by individual coal mines using their individual, diverse software. No consistent model is used within the software for data abstraction and symbolization. This paper first reviews all the essential specifications concerning OGC (Open Geospatial Consortium) interoperability. Then an OGC standard-oriented architecture is proposed to provide distributed coal mine map services. Within this new architecture the management of spatial data archives, and the integration of coal mine maps, are achieved through the interfaces of geospatial services. Finally an open source geospatial approach is suggested to implement the proposed scheme. A case study of the Huaibei Coal Group is used to demonstrate the proposal.

Surface Modification of Nanometre Silicon Carbide Powder with Polystyrene by Inductively Coupled Plasma

An investigation was made into polystyrene （PS） grafted onto nanometre silicon carbide （SIC） particles. In our experiment, the grafting polymerization reaction was induced by a radio frequency （RF） inductively coupled plasma （ICP） treatment of the nanometre powder. FTIR （Fourier transform infrared spectrum） and XPS （X-ray photoelectron spectroscopy） results reveal that PS is grafted onto the surface of silicon carbide powder. An analysis is presented on the effectiveness of this approach as a function of plasma operating variables including the plasma treating power, treating time, and grafting reaction temperature and time.

Monitoring the ionosphere based on the Crustal Movement Observation Network of China

The Global Navigation Satellite System （GNSS） is becoming important for monitoring the variations in the earth＇s ionosphere based on the total electron content （TEC） and iono- spheric electron density （IED）. The Crustal Movement Observation Network of China （CMONOC）, which includes GNSS stations across China's Mainland, enables the continuous monitoring of the ionosphere over China as accurately as possible. A series of approaches for GNSS-based ionospheric remote sensing and software has been proposed and devel- oped by the Institute of Geodesy and Geophysics （IGG） in Wuhan. Related achievements include the retrieval of ionospheric observables from raw GNSS data, differential code biases estimations in satellites and receivers, models of local and regional ionospheric TEC, and algorithms of ionospheric tomography. Based on these achievements, a software for processing GNSS data to determine the variations in ionospheric TEC and IED over China has been designed and developed by IGG. This software has also been installed at the CMONOC data centers belonging to the China Earthquake Administration and China Meteorological Administration. This paper briefly introduces the related research achievements and indicates potential directions of future work.

Infrared Indoor Wireless MIMO Communication System Using 1.2GHz OOK Modulation

The multiple input multiple output(MIMO) systems using serial infrared(SIR),return to zero-inverted(RZI) and on off keying(OOK) modulation were studied. Also, by analyzing experimental results, curve fitting models were established. Three infrared MIMO systems with 2X2, 2X4 and 4X4 MIMO channels using RZI and OOK modulation were designed and tested. Based on the experimental results, evaluations between BER, distance and displacement were discussed.

Laser-Diode End-Pumped Nd：YVO4 Slab Laser under Direct Pumping into the Emitting Level

我们在场一根 880-nm 激光二极管部分抽结束的 Nd : 有由使用一个混合共鸣器的输出 126.7 W 的 YVO4 平板 cw 激光。关于抽力量吸收的 slop 效率和 optical-to-optical 效率分别地是 73.2% 和 58.7% 。在 100 W 的产量力量，横梁繁殖 M2 因素在不稳定的方向是 1.1 并且 1.15 在稳定的方向。

A Methodology for Estimating Leaf Area Index by Assimilating Remote Sensing Data into Crop Model Based on Temporal and Spatial Knowledge

In this paper,a methodology for Leaf Area Index(LAI) estimating was proposed by assimilating remote sensed data into crop model based on temporal and spatial knowledge.Firstly,sensitive parameters of crop model were calibrated by Shuffled Complex Evolution method developed at the University of Arizona(SCE-UA) optimization method based on phenological information,which is called temporal knowledge.The calibrated crop model will be used as the forecast operator.Then,the Taylor′s mean value theorem was applied to extracting spatial information from the Moderate Resolution Imaging Spectroradiometer(MODIS) multi-scale data,which was used to calibrate the LAI inversion results by A two-layer Canopy Reflectance Model(ACRM) model.The calibrated LAI result was used as the observation operator.Finally,an Ensemble Kalman Filter(EnKF) was used to assimilate MODIS data into crop model.The results showed that the method could significantly improve the estimation accuracy of LAI and the simulated curves of LAI more conform to the crop growth situation closely comparing with MODIS LAI products.The root mean square error(RMSE) of LAI calculated by assimilation is 0.9185 which is reduced by 58.7% compared with that by simulation(0.3795),and before and after assimilation the mean error is reduced by 92.6% which is from 0.3563 to 0.0265.All these experiments indicated that the methodology proposed in this paper is reasonable and accurate for estimating crop LAI.

Kinetic Analysis of Vectored Electric Propulsion System for Stratosphere Airship

To enhance the controllability of stratosphere airship,a vectored electric propulsion system is used.By using the Lagrangian method,a kinetic model of the vectored electric propulsion system is established and validated through ground tests.The fake gyroscopic torque is first proposed,which the vector mechanism should overcome besides the inertial torque and the gravitational torque.The fake gyroscopic torque is caused by the difference between inertial moments about two principal inertial axes of the propeller in the rotating plane,appears only when the propeller is rotating and is proportional with the rotation speed.It is a sinusoidal pulse,with a frequency that is twice of the rotation speed.Considering the fake gyroscope torque pulse and aerodynamic efficiency,three blade propeller is recommended for the vectored propulsion system used for stratosphere airship.

Remote Sensing Image Deblurring Based on Grid Computation

In general, there is a demand for real-time processing of mass quantity remote sensing images. However, the task is not only data-intensive but also computating-intensive. Distributed processing is a hot topic in remote sensing processing and image deblurring is also one of the most important needs. In order to satisfy the demand for quick proc- essing and deblurring of mass quantity satellite images, we developed a distributed, grid computation-based platform as well as a corresponding middleware for grid computation. Both a constrained power spectrum equalization algorithm and effective block processing measures, which can avoid boundary effect, were applied during the processing. The re- sult is satisfactory since computation efficiency and visual effect were greatly improved. It can be concluded that the technology of spatial information grids is effective for mass quantity remote sensing image processing.

Three-dimensional paper-like graphene framework with highly orientated laminar structure as binder-free supercapacitor electrode

A free-standing paper-like three-dimensional graphene framework（3DGF） with orientated laminar structure and interconnected macropores, was obtained by the hard template-directed ordered assembly. As the sacrificial templates, polystyrene（PS） latex spheres were assembled with graphene oxide（GO） to build up a sandwich type composite film, followed by heat removal of which with a simultaneous reduction of GO. The 3DGF exhibited high specific surface area of 402.5 m2/g, controllable pores and mechanical flexibility, which was employed as the binder-free supercapacitor electrode and shows high specific gravimetric capacitance of 95 F/g at 0.5 A/g, with enhanced rate capability in 3 electrode KOH system.

Invisible Visual Cryptography

We propose to realize visual cryptography in an indirect way with the help of diffractive optics, the pure-amplitude keys being substituted with the phase-only keys that are invisible for common-used intensity detectors, leading to the significantly enhanced security and improved usability for practice. Three typical realizations are provided by using static or dynamic diffractive optical elements, and the new concept of invisible visual cryptography （IVC） may be established. This concept is demonstrated by a compact opto-electronic system with only one spatial light modulator within time-delayed exposure, maintaining the fast speed of decryption and no requirement to the calculation of decryption in conventional visual cryptography. Further, IVC shows the immunity to noises and good information capacity, which is partly inherited from diffractive optics. IVC might suggest a new strategy for visual cryptography with the respective of diverse realizations, such as opto-electronic or even bio-chemical or other methods.

Analysis of unmanned aerial vehicle navigation and height control system based on GPS

According to the characteristic of global positioning system（GPS） reflection signals,a GPS delay mapping receiver system scheme is put forward,which not only satisfies the unmanned aerial vehicle（UAV） guidance localization but also realizes height measurement.A code delay algorithm is put forward,which processes the direct and land reflected signal and outputs the navigation data and specular point.The GPS terrain reflected echo signal mathematical equation is inferred.The reflecting signal area,when the GPS signal passes the land,is analyzed.The height survey model reflected land surface characteristic is established.A simulation system which carries guidance localization of the UAV and the height measuring control through the GPS direct signal and the land reflected signal is designed,taken the GPS satellite as the illumination source,the receiver is put on the UAV.Then the UAV guidance signal,the GPS reflection signal and receiver＇s parallel processing are realized.The parallel processing reduces UAV＇s payload and raises system＇s operating efficiency.The simulation results confirms the validity of the model and also provides the basis for the UAV＇s optimization design.

Super-resolution imaging via sparsity constraint and sparse speckle illumination

We present an imaging approach via sparsity constraint and sparse speckle illumination which can dramatically en- hance the optical system＇s imaging resolution. When the object is illuminated by some sparse speckles and the sparse reconstruction algorithm is utilized to restore the blur image, numerical simulated results demonstrate that the image, whose resolution exceeds the Rayleigh limit, can be stably reconstructed even if the detection signal-to-noise ratio （SNR） is less than 10 dB. Factors affecting the quality of the reconstructed image, such as the coded pattern＇s sparsity and the detection SNR, are also studied,

Study on the quality evaluation metrics for compressed spaceborne hyperspectral data

Based on the raw data of spaceborne dispersive and interferometry imaging spectrometer,a set of quality evaluation metrics for compressed hyperspectral data is initially established in this paper.These quality evaluation metrics,which consist of four aspects including compression statistical distortion,sensor performance evaluation,data application performance and image quality,are suited to the comprehensive and systematical analysis of the impact of lossy compression in spaceborne hyperspectral remote sensing data quality.Furthermore,the evaluation results would be helpful to the selection and optimization of satellite data compression scheme.